Merge bk://linux.bkbits.net/linux-2.5

into hostme.bitkeeper.com:/repos/c/cifs/linux-2.5cifs

Documentation/i2c/porting-clients

@@ -92,10 +92,7 @@ Technical changes:
   i2c_get_clientdata(client) instead.
 
 * [Interface] Init function should not print anything. Make sure
-  there is a MODULE_LICENSE() line. MODULE_PARM() is replaced
-  by module_param(). Note that module_param has a third parameter,
-  that you should set to 0 by default. See include/linux/moduleparam.h
-  for details.
+  there is a MODULE_LICENSE() line.
 
 Coding policy:
 

arch/ia64/kernel/unaligned.c

 /*
  * Architecture-specific unaligned trap handling.
  *
- * Copyright (C) 1999-2002 Hewlett-Packard Co
+ * Copyright (C) 1999-2002, 2004 Hewlett-Packard Co
  *	Stephane Eranian <eranian@hpl.hp.com>
  *	David Mosberger-Tang <davidm@hpl.hp.com>
  *
@@ -1328,7 +1328,7 @@ ia64_handle_unaligned (unsigned long ifa, struct pt_regs *regs)
 	 * handler into reading an arbitrary kernel addresses...
 	 */
 	if (!user_mode(regs))
-		eh = SEARCH_EXCEPTION_TABLE(regs);
+		eh = search_exception_tables(regs->cr_iip + ia64_psr(regs)->ri);
 	if (user_mode(regs) || eh) {
 		if ((current->thread.flags & IA64_THREAD_UAC_SIGBUS) != 0)
 			goto force_sigbus;

arch/ia64/mm/extable.c

 /*
  * Kernel exception handling table support.  Derived from arch/alpha/mm/extable.c.
  *
- * Copyright (C) 1998, 1999, 2001-2002 Hewlett-Packard Co
+ * Copyright (C) 1998, 1999, 2001-2002, 2004 Hewlett-Packard Co
  *	David Mosberger-Tang <davidm@hpl.hp.com>
  */
 
@@ -10,9 +10,51 @@
 #include <asm/uaccess.h>
 #include <asm/module.h>
 
-void sort_extable(struct exception_table_entry *start,
-		  struct exception_table_entry *finish)
+static inline int
+compare_entries (struct exception_table_entry *l, struct exception_table_entry *r)
 {
+	u64 lip = (u64) &l->addr + l->addr;
+	u64 rip = (u64) &r->addr + r->addr;
+
+	if (lip < rip)
+		return -1;
+	if (lip == rip)
+		return 0;
+	else
+		return 1;
+}
+
+static inline void
+swap_entries (struct exception_table_entry *l, struct exception_table_entry *r)
+{
+	u64 delta = (u64) r - (u64) l;
+	struct exception_table_entry tmp;
+
+	tmp = *l;
+	l->addr = r->addr + delta;
+	l->cont = r->cont + delta;
+	r->addr = tmp.addr - delta;
+	r->cont = tmp.cont - delta;
+}
+
+/*
+ * Sort the exception table.  It's usually already sorted, but there may be unordered
+ * entries due to multiple text sections (such as the .init text section).  Note that the
+ * exception-table-entries contain location-relative addresses, which requires a bit of
+ * care during sorting to avoid overflows in the offset members (e.g., it would not be
+ * safe to make a temporary copy of an exception-table entry on the stack, because the
+ * stack may be more than 2GB away from the exception-table).
+ */
+void
+sort_extable (struct exception_table_entry *start, struct exception_table_entry *finish)
+{
+	struct exception_table_entry *p, *q;
+
+ 	/* insertion sort */
+	for (p = start + 1; p < finish; ++p)
+		/* start .. p-1 is sorted; push p down to it's proper place */
+		for (q = p; q > start && compare_entries(&q[0], &q[-1]) < 0; --q)
+			swap_entries(&q[0], &q[-1]);
 }
 
 const struct exception_table_entry *

arch/ia64/mm/fault.c

@@ -58,7 +58,7 @@ mapped_kernel_page_is_present (unsigned long address)
 	if (pgd_none(*pgd) || pgd_bad(*pgd))
 		return 0;
 
-	pmd = pmd_offset(pgd,address);
+	pmd = pmd_offset(pgd, address);
 	if (pmd_none(*pmd) || pmd_bad(*pmd))
 		return 0;
 

arch/x86_64/mm/extable.c

@@ -55,5 +55,4 @@ void sort_extable(struct exception_table_entry *start,
 			}
 		}
 	} while (change != 0);
-	return 0;
 }

arch/x86_64/mm/k8topology.c

@@ -75,7 +75,7 @@ int __init k8_scan_nodes(unsigned long start, unsigned long end)
 			continue;
 		} 
 		if (nodeid >= numnodes) { 
-			printk("Ignoring excess node %d (%x:%x)\n", nodeid, 
+			printk("Ignoring excess node %d (%lx:%lx)\n", nodeid,
 			       base, limit); 
 			continue;
 		} 

drivers/cpufreq/cpufreq.c

@@ -868,7 +868,7 @@ int cpufreq_update_policy(unsigned int cpu)
 	down(&data->lock);
 
 	memcpy(&policy, 
-	       &data, 
+	       data,
 	       sizeof(struct cpufreq_policy));
 	policy.min = data->user_policy.min;
 	policy.max = data->user_policy.max;

drivers/i2c/busses/i2c-parport.h

@@ -67,12 +67,13 @@ static struct adapter_parm adapter_parm[] = {
 		.getsda	= { 0x40, STAT, 1 },
 		.getscl	= { 0x08, STAT, 1 },
 	},
-	/* type 4: ADM 1032 evaluation board */
+	/* type 4: ADM1025 and ADM1032 evaluation boards */
 	{
 		.setsda	= { 0x02, DATA, 1 },
 		.setscl	= { 0x01, DATA, 1 },
 		.getsda	= { 0x10, STAT, 1 },
-		.init	= { 0xf0, DATA, 0 },
+		.init	= { 0xf0, DATA, 0 }, /* ADM1025 doesn't need this,
+						but it doesn't hurt */
 	},
 };
 
@@ -84,4 +85,4 @@ MODULE_PARM_DESC(type,
 	" 1 = home brew teletext adapter\n"
 	" 2 = Velleman K8000 adapter\n"
 	" 3 = ELV adapter\n"
-	" 4 = ADM 1032 evalulation board\n");
+	" 4 = ADM1025 and ADM1032 evaluation boards\n");

drivers/i2c/busses/i2c-philips-par.c

@@ -184,8 +184,8 @@ static void i2c_parport_attach (struct parport *port)
 		return;
 	}
 	/* reset hardware to sane state */
-	bit_lp_setsda(port, 1);
-	bit_lp_setscl(port, 1);
+	adapter->bit_lp_data.setsda(port, 1);
+	adapter->bit_lp_data.setscl(port, 1);
 	parport_release(adapter->pdev);
 
 	if (i2c_bit_add_bus(&adapter->adapter) < 0) {

drivers/i2c/busses/i2c-piix4.c

@@ -68,6 +68,9 @@ struct sd {
 #define SMBSLVEVT	(0xA + piix4_smba)
 #define SMBSLVDAT	(0xC + piix4_smba)
 
+/* count for request_region */
+#define SMBIOSIZE	8
+
 /* PCI Address Constants */
 #define SMBBA		0x090
 #define SMBHSTCFG	0x0D2
@@ -112,14 +115,13 @@ MODULE_PARM_DESC(fix_hstcfg,
 
 static int piix4_transaction(void);
 
-
 static unsigned short piix4_smba = 0;
 static struct i2c_adapter piix4_adapter;
 
 /*
  * Get DMI information.
  */
-static int ibm_dmi_probe(void)
+static int __devinit ibm_dmi_probe(void)
 {
 #ifdef CONFIG_X86
 	extern int is_unsafe_smbus;
@@ -129,9 +131,9 @@ static int ibm_dmi_probe(void)
 #endif
 }
 
-static int piix4_setup(struct pci_dev *PIIX4_dev, const struct pci_device_id *id)
+static int __devinit piix4_setup(struct pci_dev *PIIX4_dev,
+				const struct pci_device_id *id)
 {
-	int error_return = 0;
 	unsigned char temp;
 
 	/* match up the function */
@@ -144,8 +146,7 @@ static int piix4_setup(struct pci_dev *PIIX4_dev, const struct pci_device_id *id
 		dev_err(&PIIX4_dev->dev, "IBM Laptop detected; this module "
 			"may corrupt your serial eeprom! Refusing to load "
 			"module!\n");
-		error_return = -EPERM;
-		goto END;
+		return -EPERM;
 	}
 
 	/* Determine the address of the SMBus areas */
@@ -163,11 +164,10 @@ static int piix4_setup(struct pci_dev *PIIX4_dev, const struct pci_device_id *id
 		}
 	}
 
-	if (!request_region(piix4_smba, 8, "piix4-smbus")) {
+	if (!request_region(piix4_smba, SMBIOSIZE, "piix4-smbus")) {
 		dev_err(&PIIX4_dev->dev, "SMB region 0x%x already in use!\n",
 			piix4_smba);
-		error_return = -ENODEV;
-		goto END;
+		return -ENODEV;
 	}
 
 	pci_read_config_byte(PIIX4_dev, SMBHSTCFG, &temp);
@@ -214,8 +214,9 @@ static int piix4_setup(struct pci_dev *PIIX4_dev, const struct pci_device_id *id
 		} else {
 			dev_err(&PIIX4_dev->dev,
 				"Host SMBus controller not enabled!\n");
-			error_return = -ENODEV;
-			goto END;
+			release_region(piix4_smba, SMBIOSIZE);
+			piix4_smba = 0;
+			return -ENODEV;
 		}
 	}
 
@@ -231,8 +232,7 @@ static int piix4_setup(struct pci_dev *PIIX4_dev, const struct pci_device_id *id
 	dev_dbg(&PIIX4_dev->dev, "SMBREV = 0x%X\n", temp);
 	dev_dbg(&PIIX4_dev->dev, "SMBA = 0x%X\n", piix4_smba);
 
-END:
-	return error_return;
+	return 0;
 }
 
 /* Another internally used function */
@@ -465,7 +465,8 @@ static struct pci_device_id piix4_ids[] = {
 	{ 0, }
 };
 
-static int __devinit piix4_probe(struct pci_dev *dev, const struct pci_device_id *id)
+static int __devinit piix4_probe(struct pci_dev *dev,
+				const struct pci_device_id *id)
 {
 	int retval;
 
@@ -479,17 +480,24 @@ static int __devinit piix4_probe(struct pci_dev *dev, const struct pci_device_id
 	snprintf(piix4_adapter.name, I2C_NAME_SIZE,
 		"SMBus PIIX4 adapter at %04x", piix4_smba);
 
-	retval = i2c_add_adapter(&piix4_adapter);
+	if ((retval = i2c_add_adapter(&piix4_adapter))) {
+		dev_err(&dev->dev, "Couldn't register adapter!\n");
+		release_region(piix4_smba, SMBIOSIZE);
+		piix4_smba = 0;
+	}
 
 	return retval;
 }
 
 static void __devexit piix4_remove(struct pci_dev *dev)
 {
-	i2c_del_adapter(&piix4_adapter);
+	if (piix4_smba) {
+		i2c_del_adapter(&piix4_adapter);
+		release_region(piix4_smba, SMBIOSIZE);
+		piix4_smba = 0;
+	}
 }
 
-
 static struct pci_driver piix4_driver = {
 	.name		= "piix4-smbus",
 	.id_table	= piix4_ids,
@@ -502,15 +510,13 @@ static int __init i2c_piix4_init(void)
 	return pci_module_init(&piix4_driver);
 }
 
-
 static void __exit i2c_piix4_exit(void)
 {
 	pci_unregister_driver(&piix4_driver);
-	release_region(piix4_smba, 8);
 }
 
-MODULE_AUTHOR
-    ("Frodo Looijaard <frodol@dds.nl> and Philip Edelbrock <phil@netroedge.com>");
+MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl> and "
+		"Philip Edelbrock <phil@netroedge.com>");
 MODULE_DESCRIPTION("PIIX4 SMBus driver");
 MODULE_LICENSE("GPL");
 

drivers/i2c/chips/lm75.c

@@ -104,9 +104,9 @@ static ssize_t set_##value(struct device *dev, const char *buf, size_t count)	\
 set(temp_max, LM75_REG_TEMP_OS);
 set(temp_hyst, LM75_REG_TEMP_HYST);
 
-static DEVICE_ATTR(temp_max, S_IWUSR | S_IRUGO, show_temp_max, set_temp_max);
-static DEVICE_ATTR(temp_hyst, S_IWUSR | S_IRUGO, show_temp_hyst, set_temp_hyst);
-static DEVICE_ATTR(temp_input, S_IRUGO, show_temp_input, NULL);
+static DEVICE_ATTR(temp_max1, S_IWUSR | S_IRUGO, show_temp_max, set_temp_max);
+static DEVICE_ATTR(temp_hyst1, S_IWUSR | S_IRUGO, show_temp_hyst, set_temp_hyst);
+static DEVICE_ATTR(temp_input1, S_IRUGO, show_temp_input, NULL);
 
 static int lm75_attach_adapter(struct i2c_adapter *adapter)
 {
@@ -197,9 +197,9 @@ static int lm75_detect(struct i2c_adapter *adapter, int address, int kind)
 	lm75_init_client(new_client);
 	
 	/* Register sysfs hooks */
-	device_create_file(&new_client->dev, &dev_attr_temp_max);
-	device_create_file(&new_client->dev, &dev_attr_temp_hyst);
-	device_create_file(&new_client->dev, &dev_attr_temp_input);
+	device_create_file(&new_client->dev, &dev_attr_temp_max1);
+	device_create_file(&new_client->dev, &dev_attr_temp_hyst1);
+	device_create_file(&new_client->dev, &dev_attr_temp_input1);
 
 	return 0;
 

drivers/i2c/chips/lm78.c

@@ -369,10 +369,10 @@ static ssize_t set_temp_hyst(struct device *dev, const char *buf, size_t count)
 	return count;
 }
 
-static DEVICE_ATTR(temp_input, S_IRUGO, show_temp, NULL)
-static DEVICE_ATTR(temp_max, S_IRUGO | S_IWUSR,
+static DEVICE_ATTR(temp_input1, S_IRUGO, show_temp, NULL)
+static DEVICE_ATTR(temp_max1, S_IRUGO | S_IWUSR,
 		show_temp_over, set_temp_over)
-static DEVICE_ATTR(temp_hyst, S_IRUGO | S_IWUSR,
+static DEVICE_ATTR(temp_hyst1, S_IRUGO | S_IWUSR,
 		show_temp_hyst, set_temp_hyst)
 
 /* 3 Fans */
@@ -678,9 +678,9 @@ int lm78_detect(struct i2c_adapter *adapter, int address, int kind)
 	device_create_file(&new_client->dev, &dev_attr_in_input6);
 	device_create_file(&new_client->dev, &dev_attr_in_min6);
 	device_create_file(&new_client->dev, &dev_attr_in_max6);
-	device_create_file(&new_client->dev, &dev_attr_temp_input);
-	device_create_file(&new_client->dev, &dev_attr_temp_max);
-	device_create_file(&new_client->dev, &dev_attr_temp_hyst);
+	device_create_file(&new_client->dev, &dev_attr_temp_input1);
+	device_create_file(&new_client->dev, &dev_attr_temp_max1);
+	device_create_file(&new_client->dev, &dev_attr_temp_hyst1);
 	device_create_file(&new_client->dev, &dev_attr_fan_input1);
 	device_create_file(&new_client->dev, &dev_attr_fan_min1);
 	device_create_file(&new_client->dev, &dev_attr_fan_div1);

drivers/i2c/chips/lm85.c

@@ -48,9 +48,6 @@ static unsigned int normal_isa_range[] = { I2C_CLIENT_ISA_END };
 /* Insmod parameters */
 SENSORS_INSMOD_4(lm85b, lm85c, adm1027, adt7463);
 
-/* Enable debug if true */
-static int	lm85debug = 0;
-
 /* The LM85 registers */
 
 #define	LM85_REG_IN(nr)			(0x20 + (nr))
@@ -802,19 +799,15 @@ int lm85_detect(struct i2c_adapter *adapter, int address,
 	company = lm85_read_value(new_client, LM85_REG_COMPANY);
 	verstep = lm85_read_value(new_client, LM85_REG_VERSTEP);
 
-	if (lm85debug) {
-		printk("lm85: Detecting device at %d,0x%02x with"
+	dev_dbg(&adapter->dev, "Detecting device at %d,0x%02x with"
 		" COMPANY: 0x%02x and VERSTEP: 0x%02x\n",
 		i2c_adapter_id(new_client->adapter), new_client->addr,
 		company, verstep);
-	}
 
 	/* If auto-detecting, Determine the chip type. */
 	if (kind <= 0) {
-		if (lm85debug) {
-			printk("lm85: Autodetecting device at %d,0x%02x ...\n",
+		dev_dbg(&adapter->dev, "Autodetecting device at %d,0x%02x ...\n",
 			i2c_adapter_id(adapter), address );
-		}
 		if( company == LM85_COMPANY_NATIONAL
 		    && verstep == LM85_VERSTEP_LM85C ) {
 			kind = lm85c ;
@@ -823,8 +816,8 @@ int lm85_detect(struct i2c_adapter *adapter, int address,
 			kind = lm85b ;
 		} else if( company == LM85_COMPANY_NATIONAL
 		    && (verstep & 0xf0) == LM85_VERSTEP_GENERIC ) {
-			printk("lm85: Unrecgonized version/stepping 0x%02x"
-			    " Defaulting to LM85.\n", verstep );
+			dev_err(&adapter->dev, "Unrecgonized version/stepping 0x%02x"
+				" Defaulting to LM85.\n", verstep);
 			kind = any_chip ;
 		} else if( company == LM85_COMPANY_ANALOG_DEV
 		    && verstep == LM85_VERSTEP_ADM1027 ) {
@@ -834,21 +827,19 @@ int lm85_detect(struct i2c_adapter *adapter, int address,
 			kind = adt7463 ;
 		} else if( company == LM85_COMPANY_ANALOG_DEV
 		    && (verstep & 0xf0) == LM85_VERSTEP_GENERIC ) {
-			printk("lm85: Unrecgonized version/stepping 0x%02x"
-			    " Defaulting to ADM1027.\n", verstep );
+			dev_err(&adapter->dev, "Unrecgonized version/stepping 0x%02x"
+				" Defaulting to ADM1027.\n", verstep);
 			kind = adm1027 ;
 		} else if( kind == 0 && (verstep & 0xf0) == 0x60) {
-			printk("lm85: Generic LM85 Version 6 detected\n");
+			dev_err(&adapter->dev, "Generic LM85 Version 6 detected\n");
 			/* Leave kind as "any_chip" */
 		} else {
-			if (lm85debug) {
-				printk("lm85: Autodetection failed\n");
-			}
+			dev_dbg(&adapter->dev, "Autodetection failed\n");
 			/* Not an LM85 ... */
 			if( kind == 0 ) {  /* User used force=x,y */
-			    printk("lm85: Generic LM85 Version 6 not"
-				" found at %d,0x%02x. Try force_lm85c.\n",
-				i2c_adapter_id(adapter), address );
+				dev_err(&adapter->dev, "Generic LM85 Version 6 not"
+					" found at %d,0x%02x. Try force_lm85c.\n",
+					i2c_adapter_id(adapter), address );
 			}
 			err = 0 ;
 			goto ERROR1;
@@ -879,12 +870,10 @@ int lm85_detect(struct i2c_adapter *adapter, int address,
 	data->valid = 0;
 	init_MUTEX(&data->update_lock);
 
-	if (lm85debug) {
-		printk("lm85: Assigning ID %d to %s at %d,0x%02x\n",
+	dev_dbg(&adapter->dev, "Assigning ID %d to %s at %d,0x%02x\n",
 		new_client->id, new_client->name,
 		i2c_adapter_id(new_client->adapter),
 		new_client->addr);
-	}
 
 	/* Tell the I2C layer a new client has arrived */
 	if ((err = i2c_attach_client(new_client)))
@@ -1021,31 +1010,24 @@ void lm85_init_client(struct i2c_client *client)
 	int value;
 	struct lm85_data *data = i2c_get_clientdata(client);
 
-	if (lm85debug) {
-		printk("lm85(%d): Initializing device\n", client->id);
-	}
+	dev_dbg(&client->dev, "Initializing device\n");
 
 	/* Warn if part was not "READY" */
 	value = lm85_read_value(client, LM85_REG_CONFIG);
-	if (lm85debug) {
-		printk("lm85(%d): LM85_REG_CONFIG is: 0x%02x\n", client->id, value );
-	}
+	dev_dbg(&client->dev, "LM85_REG_CONFIG is: 0x%02x\n", value);
 	if( value & 0x02 ) {
-		printk("lm85(%d): Client (%d,0x%02x) config is locked.\n",
-			    client->id,
+		dev_err(&client->dev, "Client (%d,0x%02x) config is locked.\n",
 			    i2c_adapter_id(client->adapter), client->addr );
 	};
 	if( ! (value & 0x04) ) {
-		printk("lm85(%d): Client (%d,0x%02x) is not ready.\n",
-			    client->id,
+		dev_err(&client->dev, "Client (%d,0x%02x) is not ready.\n",
 			    i2c_adapter_id(client->adapter), client->addr );
 	};
 	if( value & 0x10
 	    && ( data->type == adm1027
 		|| data->type == adt7463 ) ) {
-		printk("lm85(%d): Client (%d,0x%02x) VxI mode is set.  "
+		dev_err(&client->dev, "Client (%d,0x%02x) VxI mode is set.  "
 			"Please report this to the lm85 maintainer.\n",
-			    client->id,
 			    i2c_adapter_id(client->adapter), client->addr );
 	};
 
@@ -1061,11 +1043,8 @@ void lm85_init_client(struct i2c_client *client)
 	value = lm85_read_value(client, LM85_REG_CONFIG);
 	/* Try to clear LOCK, Set START, save everything else */
 	value = (value & ~ 0x02) | 0x01 ;
-	if (lm85debug) {
-		printk("lm85(%d): Setting CONFIG to: 0x%02x\n", client->id, value );
-	}
+	dev_dbg(&client->dev, "Setting CONFIG to: 0x%02x\n", value);
 	lm85_write_value(client, LM85_REG_CONFIG, value);
-
 }
 
 void lm85_update_client(struct i2c_client *client)
@@ -1078,10 +1057,8 @@ void lm85_update_client(struct i2c_client *client)
 	if ( !data->valid ||
 	     (jiffies - data->last_reading > LM85_DATA_INTERVAL ) ) {
 		/* Things that change quickly */
-
-		if (lm85debug) {
-			printk("lm85(%d): Reading sensor values\n", client->id);
-		}
+		dev_dbg(&client->dev, "Reading sensor values\n");
+		
 		/* Have to read extended bits first to "freeze" the
 		 * more significant bits that are read later.
 		 */
@@ -1125,10 +1102,8 @@ void lm85_update_client(struct i2c_client *client)
 	if ( !data->valid ||
 	     (jiffies - data->last_config > LM85_CONFIG_INTERVAL) ) {
 		/* Things that don't change often */
+		dev_dbg(&client->dev, "Reading config values\n");
 
-		if (lm85debug) {
-			printk("lm85(%d): Reading config values\n", client->id);
-		}
 		for (i = 0; i <= 4; ++i) {
 			data->in_min[i] =
 			    lm85_read_value(client, LM85_REG_IN_MIN(i));
@@ -1234,8 +1209,6 @@ static void  __exit sm_lm85_exit(void)
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Philip Pokorny <ppokorny@penguincomputing.com>, Margit Schubert-While <margitsw@t-online.de>");
 MODULE_DESCRIPTION("LM85-B, LM85-C driver");
-MODULE_PARM(lm85debug, "i");
-MODULE_PARM_DESC(lm85debug, "Enable debugging statements");
 
 module_init(sm_lm85_init);
 module_exit(sm_lm85_exit);

drivers/usb/Kconfig

@@ -7,7 +7,7 @@ menu "USB support"
 # ARM SA1111 chips have a non-PCI based "OHCI-compatible" USB host interface.
 config USB
 	tristate "Support for USB"
-	depends on PCI || SA1111
+	depends on PCI || SA1111 || ARCH_OMAP1510 || ARCH_OMAP1610
 	---help---
 	  Universal Serial Bus (USB) is a specification for a serial bus
 	  subsystem which offers higher speeds and more features than the

drivers/usb/core/hub.c

@@ -31,6 +31,7 @@
 #include <asm/uaccess.h>
 #include <asm/byteorder.h>
 
+#include "usb.h"
 #include "hcd.h"
 #include "hub.h"
 
@@ -1316,8 +1317,8 @@ int usb_physical_reset_device(struct usb_device *dev)
 		kfree(descriptor);
 		usb_destroy_configuration(dev);
 
-		ret = usb_get_device_descriptor(dev);
-		if (ret < sizeof(dev->descriptor)) {
+		ret = usb_get_device_descriptor(dev, sizeof(dev->descriptor));
+		if (ret != sizeof(dev->descriptor)) {
 			if (ret < 0)
 				err("unable to get device %s descriptor "
 					"(error=%d)", dev->devpath, ret);

drivers/usb/core/message.c

@@ -546,10 +546,10 @@ void usb_sg_cancel (struct usb_sg_request *io)
  *
  * Gets a USB descriptor.  Convenience functions exist to simplify
  * getting some types of descriptors.  Use
- * usb_get_device_descriptor() for USB_DT_DEVICE,
+ * usb_get_device_descriptor() for USB_DT_DEVICE (not exported),
  * and usb_get_string() or usb_string() for USB_DT_STRING.
- * Configuration descriptors (USB_DT_CONFIG) are part of the device
- * structure, at least for the current configuration.
+ * Device (USB_DT_DEVICE) and configuration descriptors (USB_DT_CONFIG)
+ * are part of the device structure.
  * In addition to a number of USB-standard descriptors, some
  * devices also use class-specific or vendor-specific descriptors.
  *
@@ -610,6 +610,7 @@ int usb_get_string(struct usb_device *dev, unsigned short langid, unsigned char
 /**
  * usb_get_device_descriptor - (re)reads the device descriptor
  * @dev: the device whose device descriptor is being updated
+ * @size: how much of the descriptor to read
  * Context: !in_interrupt ()
  *
  * Updates the copy of the device descriptor stored in the device structure,
@@ -618,24 +619,35 @@ int usb_get_string(struct usb_device *dev, unsigned short langid, unsigned char
  * vendors product and version fields (idVendor, idProduct, and bcdDevice).
  * That lets device drivers compare against non-byteswapped constants.
  *
- * There's normally no need to use this call, although some devices
- * will change their descriptors after events like updating firmware.
+ * Not exported, only for use by the core.  If drivers really want to read
+ * the device descriptor directly, they can call usb_get_descriptor() with
+ * type = USB_DT_DEVICE and index = 0.
  *
  * This call is synchronous, and may not be used in an interrupt context.
  *
  * Returns the number of bytes received on success, or else the status code
  * returned by the underlying usb_control_msg() call.
  */
-int usb_get_device_descriptor(struct usb_device *dev)
+int usb_get_device_descriptor(struct usb_device *dev, unsigned int size)
 {
-	int ret = usb_get_descriptor(dev, USB_DT_DEVICE, 0, &dev->descriptor,
-				     sizeof(dev->descriptor));
+	struct usb_device_descriptor *desc;
+	int ret;
+
+	if (size > sizeof(*desc))
+		return -EINVAL;
+	desc = kmalloc(sizeof(*desc), GFP_NOIO);
+	if (!desc)
+		return -ENOMEM;
+
+	ret = usb_get_descriptor(dev, USB_DT_DEVICE, 0, desc, size);
 	if (ret >= 0) {
-		le16_to_cpus(&dev->descriptor.bcdUSB);
-		le16_to_cpus(&dev->descriptor.idVendor);
-		le16_to_cpus(&dev->descriptor.idProduct);
-		le16_to_cpus(&dev->descriptor.bcdDevice);
+		le16_to_cpus(&desc->bcdUSB);
+		le16_to_cpus(&desc->idVendor);
+		le16_to_cpus(&desc->idProduct);
+		le16_to_cpus(&desc->bcdDevice);
+		memcpy(&dev->descriptor, desc, size);
 	}
+	kfree(desc);
 	return ret;
 }
 
@@ -1241,7 +1253,6 @@ EXPORT_SYMBOL(usb_sg_wait);
 
 // synchronous control message convenience routines
 EXPORT_SYMBOL(usb_get_descriptor);
-EXPORT_SYMBOL(usb_get_device_descriptor);
 EXPORT_SYMBOL(usb_get_status);
 EXPORT_SYMBOL(usb_get_string);
 EXPORT_SYMBOL(usb_string);

drivers/usb/core/usb.c

@@ -206,12 +206,15 @@ void usb_deregister(struct usb_driver *driver)
  */
 struct usb_interface *usb_ifnum_to_if(struct usb_device *dev, unsigned ifnum)
 {
+	struct usb_host_config *config = dev->actconfig;
 	int i;
 
-	for (i = 0; i < dev->actconfig->desc.bNumInterfaces; i++)
-		if (dev->actconfig->interface[i]->altsetting[0]
+	if (!config)
+		return NULL;
+	for (i = 0; i < config->desc.bNumInterfaces; i++)
+		if (config->interface[i]->altsetting[0]
 				.desc.bInterfaceNumber == ifnum)
-			return dev->actconfig->interface[i];
+			return config->interface[i];
 
 	return NULL;
 }
@@ -233,14 +236,17 @@ struct usb_interface *usb_ifnum_to_if(struct usb_device *dev, unsigned ifnum)
 struct usb_endpoint_descriptor *
 usb_epnum_to_ep_desc(struct usb_device *dev, unsigned epnum)
 {
+	struct usb_host_config *config = dev->actconfig;
 	int i, k;
 
-	for (i = 0; i < dev->actconfig->desc.bNumInterfaces; i++) {
+	if (!config)
+		return NULL;
+	for (i = 0; i < config->desc.bNumInterfaces; i++) {
 		struct usb_interface		*intf;
 		struct usb_host_interface	*alt;
 
-		/* only endpoints in current altseting are active */
-		intf = dev->actconfig->interface[i];
+		/* only endpoints in current altsetting are active */
+		intf = config->interface[i];
 		alt = intf->altsetting + intf->act_altsetting;
 
 		for (k = 0; k < alt->desc.bNumEndpoints; k++)
@@ -1059,7 +1065,7 @@ int usb_new_device(struct usb_device *dev, struct device *parent)
 		wait_ms(10);	/* Let the SET_ADDRESS settle */
 
 		/* high and low speed devices don't need this... */
-		err = usb_get_descriptor(dev, USB_DT_DEVICE, 0, &dev->descriptor, 8);
+		err = usb_get_device_descriptor(dev, 8);
 		if (err >= 8)
 			break;
 		wait_ms(100);
@@ -1079,8 +1085,8 @@ int usb_new_device(struct usb_device *dev, struct device *parent)
 
 	/* USB device state == addressed ... still not usable */
 
-	err = usb_get_device_descriptor(dev);
-	if (err < (signed)sizeof(dev->descriptor)) {
+	err = usb_get_device_descriptor(dev, sizeof(dev->descriptor));
+	if (err != (signed)sizeof(dev->descriptor)) {
 		dev_err(&dev->dev, "device descriptor read/all, error %d\n", err);
 		goto fail;
 	}

drivers/usb/core/usb.h

@@ -14,3 +14,6 @@ extern void usb_enable_endpoint (struct usb_device *dev,
 		struct usb_endpoint_descriptor *epd);
 extern void usb_enable_interface (struct usb_device *dev,
 		struct usb_interface *intf);
+
+extern int usb_get_device_descriptor(struct usb_device *dev,
+		unsigned int size);

drivers/usb/gadget/Kconfig

@@ -3,12 +3,10 @@
 #    (a) a peripheral controller, and
 #    (b) the gadget driver using it.
 #
-# for 2.5 kbuild, drivers/usb/gadget/Kconfig
-# source this at the end of drivers/usb/Kconfig
-#
-menuconfig USB_GADGET
+menu "USB Gadget Support"
+
+config USB_GADGET
 	tristate "Support for USB Gadgets"
-	depends on EXPERIMENTAL
 	help
 	   USB is a master/slave protocol, organized with one master
 	   host (such as a PC) controlling up to 127 peripheral devices.
@@ -36,12 +34,15 @@ menuconfig USB_GADGET
 # USB Peripheral Controller Support
 #
 choice
-	prompt "USB Peripheral Controller Support"
+	prompt "USB Peripheral Controller"
 	depends on USB_GADGET
+	help
+	   A USB device uses a controller to talk to its host.
+	   Systems should have only one such upstream link.
 
-config USB_NET2280
-	tristate "NetChip 2280 USB Peripheral Controller"
-	depends on PCI && USB_GADGET
+config USB_GADGET_NET2280
+	boolean "NetChip 2280"
+	depends on PCI
 	help
 	   NetChip 2280 is a PCI based USB peripheral controller which
 	   supports both full and high speed USB 2.0 data transfers.  
@@ -54,21 +55,91 @@ config USB_NET2280
 	   dynamically linked module called "net2280" and force all
 	   gadget drivers to also be dynamically linked.
 
+config USB_NET2280
+	tristate
+	depends on USB_GADGET_NET2280
+	default USB_GADGET
+
+config USB_GADGET_PXA2XX
+	boolean "PXA 2xx or IXP 42x"
+	depends on ARCH_PXA || ARCH_IXP425
+	help
+	   Intel's PXA 2xx series XScale ARM-5TE processors include
+	   an integrated full speed USB 1.1 device controller.  The
+	   controller in the IXP 4xx series is register-compatible.
+
+	   It has fifteen fixed-function endpoints, as well as endpoint
+	   zero (for control transfers).
+
+	   Say "y" to link the driver statically, or "m" to build a
+	   dynamically linked module called "pxa2xx_udc" and force all
+	   gadget drivers to also be dynamically linked.
+
+config USB_PXA2XX
+	tristate
+	depends on USB_GADGET_PXA2XX
+	default USB_GADGET
+
+# if there's only one gadget driver, using only two bulk endpoints,
+# don't waste memory for the other endpoints
+config USB_PXA2XX_SMALL
+	depends on USB_GADGET_PXA2XX
+	bool
+	default y if USB_ZERO
+	default y if USB_ETH
+	default y if USB_G_SERIAL
+
+config USB_GADGET_GOKU
+	boolean "Toshiba TC86C001 'Goku-S'"
+	depends on PCI
+	help
+	   The Toshiba TC86C001 is a PCI device which includes controllers
+	   for full speed USB devices, IDE, I2C, SIO, plus a USB host (OHCI).
+	   
+	   The device controller has three configurable (bulk or interrupt)
+	   endpoints, plus endpoint zero (for control transfers).
+
+	   Say "y" to link the driver statically, or "m" to build a
+	   dynamically linked module called "goku_udc" and to force all
+	   gadget drivers to also be dynamically linked.
+
+config USB_GOKU
+	tristate
+	depends on USB_GADGET_GOKU
+	default USB_GADGET
+
+# this could be built elsewhere (doesn't yet exist)
+config USB_GADGET_SA1100
+	boolean "SA 1100"
+	depends on ARCH_SA1100
+	help
+	   Intel's SA-1100 is an ARM-4 processor with an integrated
+	   full speed USB 1.1 device controller.
+
+	   It has two fixed-function endpoints, as well as endpoint
+	   zero (for control transfers).
+
+config USB_SA1100
+	tristate
+	depends on USB_GADGET_SA1100
+	default USB_GADGET
+
 endchoice
 
+
 #
 # USB Gadget Drivers
 #
 choice
-	prompt "USB Gadget Drivers"
+	tristate "USB Gadget Drivers"
 	depends on USB_GADGET
 	default USB_ETH
 
-# FIXME want a cleaner dependency/config approach for drivers.
+# this first set of drivers all depend on bulk-capable hardware.
 
 config USB_ZERO
 	tristate "Gadget Zero (DEVELOPMENT)"
-	depends on USB_GADGET && (USB_DUMMY_HCD || USB_NET2280 || USB_PXA2XX || USB_SA1100)
+	depends on EXPERIMENTAL
 	help
 	  Gadget Zero is a two-configuration device.  It either sinks and
 	  sources bulk data; or it loops back a configurable number of
@@ -91,26 +162,9 @@ config USB_ZERO
 	  Say "y" to link the driver statically, or "m" to build a
 	  dynamically linked module called "g_zero".
 
-config USB_ZERO_NET2280
-	bool
-	# for now, treat the "dummy" hcd as if it were a net2280
-	depends on USB_ZERO && (USB_NET2280 || USB_DUMMY_HCD)
-	default y
-
-config USB_ZERO_PXA2XX
-	bool
-	depends on USB_ZERO && USB_PXA2XX
-	default y
-
-config USB_ZERO_SA1100
-	bool
-	depends on USB_ZERO && USB_SA1100
-	default y
-
-
 config USB_ETH
 	tristate "Ethernet Gadget"
-	depends on USB_GADGET && NET && (USB_DUMMY_HCD || USB_NET2280 || USB_PXA2XX || USB_SA1100)
+	depends on NET
 	help
 	  This driver implements Ethernet style communication, in either
 	  of two ways:
@@ -136,26 +190,9 @@ config USB_ETH
 	  Say "y" to link the driver statically, or "m" to build a
 	  dynamically linked module called "g_ether".
 
-
-config USB_ETH_NET2280
-	bool
-	# for now, treat the "dummy" hcd as if it were a net2280
-	depends on USB_ETH && (USB_NET2280 || USB_DUMMY_HCD)
-	default y
-
-config USB_ETH_PXA2XX
-	bool
-	depends on USB_ETH && USB_PXA2XX
-	default y
-
-config USB_ETH_SA1100
-	bool
-	depends on USB_ETH && USB_SA1100
-	default y
-
 config USB_GADGETFS
 	tristate "Gadget Filesystem (EXPERIMENTAL)"
-	depends on USB_GADGET && (USB_DUMMY_HCD || USB_NET2280 || USB_PXA2XX) && EXPERIMENTAL
+	depends on EXPERIMENTAL
 	help
 	  This driver provides a filesystem based API that lets user mode
 	  programs implement a single-configuration USB device, including
@@ -166,38 +203,44 @@ config USB_GADGETFS
 	  Say "y" to link the driver statically, or "m" to build a
 	  dynamically linked module called "gadgetfs".
 
-config USB_GADGETFS_NET2280
-	bool
-	# for now, treat the "dummy" hcd as if it were a net2280
-	depends on USB_GADGETFS && (USB_NET2280 || USB_DUMMY_HCD)
-	default y
+config USB_FILE_STORAGE
+	tristate "File-backed Storage Gadget (DEVELOPMENT)"
+	# we don't support the SA1100 because of its limitations
+	depends on USB_GADGET_SA1100 = n
+	help
+	  The File-backed Storage Gadget acts as a USB Mass Storage
+	  disk drive.  As its storage repository it can use a regular
+	  file or a block device (in much the same way as the "loop"
+	  device driver), specified as a module parameter.
 
-config USB_GADGETFS_PXA2XX
-	bool
-	depends on USB_GADGETFS && USB_PXA2XX
-	default y
+	  Say "y" to link the driver statically, or "m" to build a
+	  dynamically linked module called "g_file_storage".
+
+config USB_FILE_STORAGE_TEST
+	bool "File-backed Storage Gadget test version"
+	depends on USB_FILE_STORAGE
+	default n
+	help
+	  Say "y" to generate the larger testing version of the
+	  File-backed Storage Gadget, useful for probing the
+	  behavior of USB Mass Storage hosts.  Not needed for
+	  normal operation.
 
 config USB_G_SERIAL
-	tristate "serial Gadget"
-	depends on USB_GADGET && (USB_DUMMY_HCD || USB_NET2280 || USB_PXA2XX || USB_SA1100)
+	tristate "Serial Gadget"
+	help
+	  The Serial Gadget talks to the Linux-USB generic serial driver.
 
-config USB_G_SERIAL_NET2280
-	bool
-	# for now, treat the "dummy" hcd as if it were a net2280
-	depends on USB_G_SERIAL && (USB_NET2280 || USB_DUMMY_HCD)
-	default y
+	  Say "y" to link the driver statically, or "m" to build a
+	  dynamically linked module called "g_serial".
 
-config USB_G_SERIAL_PXA2XX
-	bool
-	depends on USB_G_SERIAL && USB_PXA2XX
-	default y
 
-config USB_G_SERIAL_SA1100
-	bool
-	depends on USB_G_SERIAL && USB_SA1100
-	default y
 
+# put drivers that need isochronous transfer support (for audio
+# or video class gadget drivers), or specific hardware, here.
+
+# - none yet
 
 endchoice
 
-# endmenuconfig
+endmenu

drivers/usb/gadget/Makefile

@@ -2,6 +2,8 @@
 # USB peripheral controller drivers
 #
 obj-$(CONFIG_USB_NET2280)	+= net2280.o
+obj-$(CONFIG_USB_PXA2XX)	+= pxa2xx_udc.o
+obj-$(CONFIG_USB_GOKU)		+= goku_udc.o
 
 #
 # USB gadget drivers
@@ -10,8 +12,11 @@ g_zero-objs			:= zero.o usbstring.o
 g_ether-objs			:= ether.o usbstring.o
 g_serial-objs			:= serial.o usbstring.o
 gadgetfs-objs			:= inode.o usbstring.o
+g_file_storage-objs		:= file_storage.o usbstring.o
  
 obj-$(CONFIG_USB_ZERO)		+= g_zero.o
 obj-$(CONFIG_USB_ETH)		+= g_ether.o
 obj-$(CONFIG_USB_GADGETFS)	+= gadgetfs.o
+obj-$(CONFIG_USB_FILE_STORAGE)	+= g_file_storage.o
 obj-$(CONFIG_USB_G_SERIAL)	+= g_serial.o
+

drivers/usb/gadget/ether.c

@@ -122,12 +122,9 @@ struct eth_dev {
  *
  * CHIP ... hardware identifier
  * DRIVER_VERSION_NUM ... alerts the host side driver to differences
- * EP0_MAXPACKET ... controls packetization of control requests
  * EP_*_NAME ... which endpoints do we use for which purpose?
  * EP_*_NUM ... numbers for them (often limited by hardware)
  * HIGHSPEED ... define if ep0 and descriptors need high speed support
- * MAX_USB_POWER ... define if we use other than 100 mA bus current
- * SELFPOWER ... unless we can run on bus power, USB_CONFIG_ATT_SELFPOWER
  * WAKEUP ... if hardware supports remote wakeup AND we will issue the
  * 	usb_gadget_wakeup() call to initiate it, USB_CONFIG_ATT_WAKEUP
  *
@@ -143,6 +140,9 @@ struct eth_dev {
 /* #undef on hardware that can't implement CDC */
 #define	DEV_CONFIG_CDC
 
+/* undef on bus-powered hardware, and #define MAX_USB_POWER */
+#define SELFPOWER
+
 /*
  * NetChip 2280, PCI based.
  *
@@ -152,11 +152,10 @@ struct eth_dev {
  * performance note:  only PIO needs per-usb-packet IRQs (ep0, ep-e, ep-f)
  * otherwise IRQs are per-Ethernet-packet unless TX_DELAY and chaining help.
  */
-#ifdef	CONFIG_USB_ETH_NET2280
+#ifdef	CONFIG_USB_GADGET_NET2280
 #define CHIP			"net2280"
 #define DEFAULT_QLEN		4		/* has dma chaining */
 #define DRIVER_VERSION_NUM	0x0101
-#define EP0_MAXPACKET		64
 static const char EP_OUT_NAME [] = "ep-a";
 #define EP_OUT_NUM	1
 static const char EP_IN_NAME [] = "ep-b";
@@ -164,8 +163,6 @@ static const char EP_IN_NAME [] = "ep-b";
 static const char EP_STATUS_NAME [] = "ep-f";
 #define EP_STATUS_NUM	3
 #define HIGHSPEED
-/* specific hardware configs could be bus-powered */
-#define SELFPOWER USB_CONFIG_ATT_SELFPOWER
 /* supports remote wakeup, but this driver doesn't */
 
 extern int net2280_set_fifo_mode (struct usb_gadget *gadget, int mode);
@@ -186,17 +183,14 @@ static inline void hw_optimize (struct usb_gadget *gadget)
  * multiple interfaces (or altsettings) aren't usable.  so this hardware
  * can't implement CDC, which needs both capabilities.
  */
-#ifdef	CONFIG_USB_ETH_PXA2XX
+#ifdef	CONFIG_USB_GADGET_PXA2XX
 #undef	DEV_CONFIG_CDC
 #define CHIP			"pxa2xx"
 #define DRIVER_VERSION_NUM	0x0103
-#define EP0_MAXPACKET		16
 static const char EP_OUT_NAME [] = "ep2out-bulk";
 #define EP_OUT_NUM	2
 static const char EP_IN_NAME [] = "ep1in-bulk";
 #define EP_IN_NUM	1
-/* doesn't support bus-powered operation */
-#define SELFPOWER USB_CONFIG_ATT_SELFPOWER
 /* supports remote wakeup, but this driver doesn't */
 
 /* no hw optimizations to apply */
@@ -209,17 +203,14 @@ static const char EP_IN_NAME [] = "ep1in-bulk";
  * can't have a notification endpoint, since there are only the two
  * bulk-capable ones.  the CDC spec allows that.
  */
-#ifdef	CONFIG_USB_ETH_SA1100
+#ifdef	CONFIG_USB_GADGET_SA1100
 #define CHIP			"sa1100"
 #define DRIVER_VERSION_NUM	0x0105
-#define EP0_MAXPACKET		8
 static const char EP_OUT_NAME [] = "ep1out-bulk";
 #define EP_OUT_NUM	1
 static const char EP_IN_NAME [] = "ep2in-bulk";
 #define EP_IN_NUM	2
 // EP_STATUS_NUM is undefined
-/* doesn't support bus-powered operation */
-#define SELFPOWER USB_CONFIG_ATT_SELFPOWER
 /* doesn't support remote wakeup? */
 
 /* no hw optimizations to apply */
@@ -231,25 +222,43 @@ static const char EP_IN_NAME [] = "ep2in-bulk";
  *
  * This has three semi-configurable full speed bulk/interrupt endpoints.
  */
-#ifdef	CONFIG_USB_ETH_GOKU
+#ifdef	CONFIG_USB_GADGET_GOKU
 #define CHIP			"goku"
 #define DRIVER_VERSION_NUM	0x0106
-#define EP0_MAXPACKET		8
 static const char EP_OUT_NAME [] = "ep1-bulk";
 #define EP_OUT_NUM	1
 static const char EP_IN_NAME [] = "ep2-bulk";
 #define EP_IN_NUM	2
 static const char EP_STATUS_NAME [] = "ep3-bulk";
 #define EP_STATUS_NUM	3
-#define SELFPOWER USB_CONFIG_ATT_SELFPOWER
 /* doesn't support remote wakeup */
 
 #define hw_optimize(g) do {} while (0)
 #endif
 
+/*
+ * SuperH UDC:  UDC built-in to some Renesas SH processors.
+ *
+ * This has three semi-configurable full speed bulk/interrupt endpoints.
+ *
+ * Only one configuration and interface is supported.  So this hardware
+ * can't implement CDC.
+ */
+#ifdef	CONFIG_USB_GADGET_SUPERH
+#undef	DEV_CONFIG_CDC
+#define CHIP			"superh"
+#define DRIVER_VERSION_NUM	0x0107
+static const char EP_OUT_NAME[] = "ep1out-bulk";
+#define EP_OUT_NUM		1
+static const char EP_IN_NAME[] = "ep2in-bulk";
+#define EP_IN_NUM		2
+
+#define hw_optimize(g) do {} while (0)
+#endif
+
 /*-------------------------------------------------------------------------*/
 
-#ifndef EP0_MAXPACKET
+#ifndef CHIP
 #	error Configure some USB peripheral controller driver!
 #endif
 
@@ -280,19 +289,15 @@ static const char EP_STATUS_NAME [] = "ep3-bulk";
  * hardware that supports remote wakeup defaults to disabling it.
  */
 
-#ifndef	SELFPOWER
-/* default: say we rely on bus power */
-#define SELFPOWER	0
-/* else:
- * - SELFPOWER value must be USB_CONFIG_ATT_SELFPOWER
- * - MAX_USB_POWER may be nonzero.
- */
-#endif
-
 #ifndef	MAX_USB_POWER
-/* any hub supports this steady state bus power consumption */
-#define MAX_USB_POWER	100	/* mA */
+#ifdef	SELFPOWER
+/* some hosts are confused by 0mA  */
+#define MAX_USB_POWER	2	/* mA */
+#else
+/* bus powered */
+#error	Define your bus power consumption!
 #endif
+#endif	/* MAX_USB_POWER */
 
 #ifndef	WAKEUP
 /* default: this driver won't do remote wakeup */
@@ -376,7 +381,7 @@ module_param (qmult, uint, S_IRUGO|S_IWUSR);
 /*
  * This device advertises one configuration.
  */
-static const struct usb_device_descriptor
+static struct usb_device_descriptor
 device_desc = {
 	.bLength =		sizeof device_desc,
 	.bDescriptorType =	USB_DT_DEVICE,
@@ -386,7 +391,6 @@ device_desc = {
 	.bDeviceClass =		DEV_CONFIG_CLASS,
 	.bDeviceSubClass =	0,
 	.bDeviceProtocol =	0,
-	.bMaxPacketSize0 =	EP0_MAXPACKET,
 
 	.idVendor =		__constant_cpu_to_le16 (DRIVER_VENDOR_NUM),
 	.idProduct =		__constant_cpu_to_le16 (DRIVER_PRODUCT_NUM),
@@ -396,7 +400,7 @@ device_desc = {
 	.bNumConfigurations =	1,
 };
 
-static const struct usb_config_descriptor
+static struct usb_config_descriptor
 eth_config = {
 	.bLength =		sizeof eth_config,
 	.bDescriptorType =	USB_DT_CONFIG,
@@ -409,7 +413,7 @@ eth_config = {
 #endif
 	.bConfigurationValue =	DEV_CONFIG_VALUE,
 	.iConfiguration =	STRING_PRODUCT,
-	.bmAttributes =		USB_CONFIG_ATT_ONE | SELFPOWER | WAKEUP,
+	.bmAttributes =		USB_CONFIG_ATT_ONE | WAKEUP,
 	.bMaxPower =		(MAX_USB_POWER + 1) / 2,
 };
 
@@ -645,7 +649,7 @@ hs_sink_desc = {
 	.bInterval =		1,
 };
 
-static const struct usb_qualifier_descriptor
+static struct usb_qualifier_descriptor
 dev_qualifier = {
 	.bLength =		sizeof dev_qualifier,
 	.bDescriptorType =	USB_DT_DEVICE_QUALIFIER,
@@ -653,12 +657,10 @@ dev_qualifier = {
 	.bcdUSB =		__constant_cpu_to_le16 (0x0200),
 	.bDeviceClass =		DEV_CONFIG_CLASS,
 
-	/* assumes ep0 uses the same value for both speeds ... */
-	.bMaxPacketSize0 =	EP0_MAXPACKET,
-
 	.bNumConfigurations =	1,
 };
 
+
 /* maxpacket and other transfer characteristics vary by speed. */
 #define ep_desc(g,hs,fs) (((g)->speed==USB_SPEED_HIGH)?(hs):(fs))
 
@@ -959,7 +961,7 @@ eth_set_config (struct eth_dev *dev, unsigned number, int gfp_flags)
 	if (number == dev->config)
 		return 0;
 
-#ifdef CONFIG_USB_ETH_SA1100
+#ifdef CONFIG_USB_GADGET_SA1100
 	if (dev->config && atomic_read (&dev->tx_qlen) != 0) {
 		/* tx fifo is full, but we can't clear it...*/
 		INFO (dev, "can't change configurations\n");
@@ -1006,6 +1008,7 @@ eth_set_config (struct eth_dev *dev, unsigned number, int gfp_flags)
 
 /* section 3.8.2 table 11 of the CDC spec lists Ethernet notifications */
 #define CDC_NOTIFY_NETWORK_CONNECTION	0x00	/* required; 6.3.1 */
+#define CDC_NOTIFY_RESPONSE_AVAILABLE	0x01	/* optional; 6.3.2 */
 #define CDC_NOTIFY_SPEED_CHANGE		0x2a	/* required; 6.3.8 */
 
 struct cdc_notification {
@@ -1123,6 +1126,8 @@ static void eth_setup_complete (struct usb_ep *ep, struct usb_request *req)
 /* see section 3.8.2 table 10 of the CDC spec for more ethernet
  * requests, mostly for filters (multicast, pm) and statistics
  */
+#define CDC_SEND_ENCAPSULATED_REQUEST	0x00	/* optional */
+#define CDC_GET_ENCAPSULATED_RESPONSE	0x01	/* optional */
 #define CDC_SET_ETHERNET_PACKET_FILTER	0x43	/* required */
 
 /*
@@ -1188,7 +1193,7 @@ eth_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
 		value = eth_set_config (dev, ctrl->wValue, GFP_ATOMIC);
 		spin_unlock (&dev->lock);
 		break;
-#ifdef	CONFIG_USB_ETH_PXA2XX
+#ifdef	CONFIG_USB_GADGET_PXA2XX
 	/* PXA UDC prevents us from using SET_INTERFACE in normal ways.
 	 * And it hides GET_CONFIGURATION and GET_INTERFACE too.
 	 */
@@ -1638,7 +1643,7 @@ static int eth_start_xmit (struct sk_buff *skb, struct net_device *net)
 	req->context = skb;
 	req->complete = tx_complete;
 
-#ifdef	CONFIG_USB_ETH_SA1100
+#ifdef	CONFIG_USB_GADGET_SA1100
 	/* don't demand zlp (req->zero) support from all hardware */
 	if ((length % dev->in_ep->maxpacket) == 0)
 		length++;
@@ -1770,6 +1775,17 @@ eth_bind (struct usb_gadget *gadget)
 		return -ENODEV;
 #endif
 
+	device_desc.bMaxPacketSize0 = gadget->ep0->maxpacket;
+#ifdef	HIGHSPEED
+	/* assumes ep0 uses the same value for both speeds ... */
+	dev_qualifier.bMaxPacketSize0 = device_desc.bMaxPacketSize0;
+#endif
+
+#ifdef	SELFPOWERED
+	eth_config.bmAttributes |= USB_CONFIG_ATT_SELFPOWERED;
+	usb_gadget_set_selfpowered (gadget);
+#endif
+
  	net = alloc_etherdev (sizeof *dev);
  	if (!net)
 		return status;

drivers/usb/gadget/inode.c

@@ -232,18 +232,27 @@ static void put_ep (struct ep_data *data)
  * the usb controller exposes.
  */
 
-#ifdef	CONFIG_USB_GADGETFS_NET2280
+#ifdef	CONFIG_USB_GADGET_DUMMY_HCD
+/* act (mostly) like a net2280 */
+#define CONFIG_USB_GADGET_NET2280
+#endif
+
+#ifdef	CONFIG_USB_GADGET_NET2280
 #define CHIP			"net2280"
 #define HIGHSPEED
 #endif
 
-#ifdef	CONFIG_USB_GADGETFS_PXA2XX
+#ifdef	CONFIG_USB_GADGET_PXA2XX
 #define CHIP			"pxa2xx_udc"
 /* earlier hardware doesn't have UDCCFR, races set_{config,interface} */
 #warning works best with pxa255 or newer
 #endif
 
-#ifdef	CONFIG_USB_GADGETFS_SA1100
+#ifdef	CONFIG_USB_GADGET_GOKU
+#define CHIP			"goku_udc"
+#endif
+
+#ifdef	CONFIG_USB_GADGET_SA1100
 #define CHIP			"sa1100"
 #endif
 
@@ -397,7 +406,7 @@ ep_io (struct ep_data *epdata, void *buf, unsigned len)
 
 /* handle a synchronous OUT bulk/intr/iso transfer */
 static ssize_t
-ep_read (struct file *fd, char *buf, size_t len, loff_t *ptr)
+ep_read (struct file *fd, char __user *buf, size_t len, loff_t *ptr)
 {
 	struct ep_data		*data = fd->private_data;
 	void			*kbuf;
@@ -441,7 +450,7 @@ ep_read (struct file *fd, char *buf, size_t len, loff_t *ptr)
 
 /* handle a synchronous IN bulk/intr/iso transfer */
 static ssize_t
-ep_write (struct file *fd, const char *buf, size_t len, loff_t *ptr)
+ep_write (struct file *fd, const char __user *buf, size_t len, loff_t *ptr)
 {
 	struct ep_data		*data = fd->private_data;
 	void			*kbuf;

drivers/usb/gadget/net2280.h

@@ -520,6 +520,7 @@ struct net2280_ep {
 	unsigned				num : 8,
 						fifo_size : 12,
 						in_fifo_validate : 1,
+						out_overflow : 1,
 						stopped : 1,
 						is_in : 1,
 						is_iso : 1;
@@ -529,6 +530,7 @@ static inline void allow_status (struct net2280_ep *ep)
 {
 	/* ep0 only */
 	writel (  (1 << CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE)
+		| (1 << CLEAR_NAK_OUT_PACKETS)
 		| (1 << CLEAR_NAK_OUT_PACKETS_MODE)
 		, &ep->regs->ep_rsp);
 	ep->stopped = 1;
@@ -546,7 +548,6 @@ struct net2280_request {
 	dma_addr_t			td_dma;
 	struct list_head		queue;
 	unsigned			mapped : 1,
-					dma_done : 1,
 					valid : 1;
 };
 
@@ -559,8 +560,7 @@ struct net2280 {
 	unsigned			enabled : 1,
 					protocol_stall : 1,
 					got_irq : 1,
-					region : 1,
-					selfpowered : 1;
+					region : 1;
 	u16				chiprev;
 
 	/* pci state used to access those endpoints */

drivers/usb/gadget/serial.c

@@ -135,9 +135,6 @@ do {									\
 
 #define GS_NUM_PORTS			16
 
-#define GS_VENDOR_ID			0x05F9
-#define GS_PRODUCT_ID			0xFFFF
-
 #define GS_NUM_CONFIGS			1
 #define GS_NO_CONFIG_ID			0
 #define GS_BULK_CONFIG_ID		2
@@ -187,7 +184,7 @@ static int debug = G_SERIAL_DEBUG;
  * DMA channels to manage their FIFOs.  It supports high speed.
  * Those endpoints can be arranged in any desired configuration.
  */
-#ifdef	CONFIG_USB_G_SERIAL_NET2280
+#ifdef	CONFIG_USB_GADGET_NET2280
 #define CHIP				"net2280"
 #define EP0_MAXPACKET			64
 static const char EP_OUT_NAME[] =	"ep-a";
@@ -220,13 +217,13 @@ static inline void hw_optimize(struct usb_gadget *gadget)
  * can't use altsettings or reset the interfaces independently.
  * So stick to a single interface.
  */
-#ifdef	CONFIG_USB_G_SERIAL_PXA2XX
+#ifdef	CONFIG_USB_GADGET_PXA2XX
 #define CHIP				"pxa2xx"
 #define EP0_MAXPACKET			16
-static const char EP_OUT_NAME[] =	"ep12out-bulk";
-#define EP_OUT_NUM			12
-static const char EP_IN_NAME[] =	"ep11in-bulk";
-#define EP_IN_NUM			11
+static const char EP_OUT_NAME[] =	"ep2out-bulk";
+#define EP_OUT_NUM			2
+static const char EP_IN_NAME[] =	"ep1in-bulk";
+#define EP_IN_NUM			1
 #define SELFPOWER 			USB_CONFIG_ATT_SELFPOWER
 
 /* no hw optimizations to apply */
@@ -245,7 +242,7 @@ static const char EP_IN_NAME[] =	"ep11in-bulk";
  * in special situations.  So this is a case of "choose it right
  * during enumeration" ...
  */
-#ifdef	CONFIG_USB_G_SERIAL_SA1100
+#ifdef	CONFIG_USB_GADGET_SA1100
 #define CHIP				"sa1100"
 #define EP0_MAXPACKET			8
 static const char EP_OUT_NAME[] =	"ep1out-bulk";
@@ -264,7 +261,7 @@ static const char EP_IN_NAME [] =	"ep2in-bulk";
  *
  * This has three semi-configurable full speed bulk/interrupt endpoints.
  */
-#ifdef	CONFIG_USB_G_SERIAL_GOKU
+#ifdef	CONFIG_USB_GADGET_GOKU
 #define CHIP				"goku"
 #define DRIVER_VERSION_NUM		0x0116
 #define EP0_MAXPACKET			8
@@ -302,6 +299,14 @@ static const char EP_IN_NAME [] =	"ep2-bulk";
 /* else value must be USB_CONFIG_ATT_WAKEUP */
 #endif
 
+/* Thanks to NetChip Technologies for donating this product ID.
+ *
+ * DO NOT REUSE THESE IDs with a protocol-incompatible driver!!  Ever!!
+ * Instead:  allocate your own, using normal USB-IF procedures.
+ */
+#define GS_VENDOR_ID	0x0525		/* NetChip */
+#define GS_PRODUCT_ID	0xa4a6		/* Linux-USB Serial Gadget */
+
 
 /* Structures */
 

drivers/usb/gadget/zero.c

@@ -131,7 +131,7 @@ static const char loopback [] = "loop input to output";
  * DMA channels to manage their FIFOs.  It supports high speed.
  * Those endpoints can be arranged in any desired configuration.
  */
-#ifdef	CONFIG_USB_ZERO_NET2280
+#if defined(CONFIG_USB_GADGET_NET2280) || defined(CONFIG_USB_GADGET_DUMMY_HCD)
 #define CHIP			"net2280"
 #define DRIVER_VERSION_NUM	0x0101
 static const char EP_OUT_NAME [] = "ep-a";
@@ -154,7 +154,7 @@ static const char EP_IN_NAME [] = "ep-b";
  * can't use altsettings or reset the interfaces independently.
  * So stick to a single interface.
  */
-#ifdef	CONFIG_USB_ZERO_PXA2XX
+#ifdef	CONFIG_USB_GADGET_PXA2XX
 #define CHIP			"pxa2xx"
 #define DRIVER_VERSION_NUM	0x0103
 static const char EP_OUT_NAME [] = "ep12out-bulk";
@@ -176,7 +176,7 @@ static const char EP_IN_NAME [] = "ep11in-bulk";
  * in special situations.  So this is a case of "choose it right
  * during enumeration" ...
  */
-#ifdef	CONFIG_USB_ZERO_SA1100
+#ifdef	CONFIG_USB_GADGET_SA1100
 #define CHIP			"sa1100"
 #define DRIVER_VERSION_NUM	0x0105
 static const char EP_OUT_NAME [] = "ep1out-bulk";
@@ -192,7 +192,7 @@ static const char EP_IN_NAME [] = "ep2in-bulk";
  *
  * This has three semi-configurable full speed bulk/interrupt endpoints.
  */
-#ifdef	CONFIG_USB_ZERO_GOKU
+#ifdef	CONFIG_USB_GADGET_GOKU
 #define CHIP			"goku"
 #define DRIVER_VERSION_NUM	0x0106
 static const char EP_OUT_NAME [] = "ep1-bulk";
@@ -936,7 +936,7 @@ zero_set_config (struct zero_dev *dev, unsigned number, int gfp_flags)
 	if (number == dev->config)
 		return 0;
 
-#ifdef CONFIG_USB_ZERO_SA1100
+#ifdef CONFIG_USB_GADGET_SA1100
 	if (dev->config) {
 		/* tx fifo is full, but we can't clear it...*/
 		INFO (dev, "can't change configurations\n");

drivers/usb/host/ohci-hcd.c

@@ -684,6 +684,10 @@ MODULE_LICENSE ("GPL");
 #include "ohci-sa1111.c"
 #endif
 
-#if !(defined(CONFIG_PCI) || defined(CONFIG_SA1111))
+#ifdef CONFIG_ARCH_OMAP
+#include "ohci-omap.c"
+#endif
+
+#if !(defined(CONFIG_PCI) || defined(CONFIG_SA1111) || defined(CONFIG_ARCH_OMAP))
 #error "missing bus glue for ohci-hcd"
 #endif

drivers/usb/host/ohci-omap.h

+/*
+ * linux/drivers/usb/host/ohci-omap.h
+ *
+ * OMAP OHCI USB controller specific defines
+ */
+
+/* OMAP USB OHCI common defines */
+#define OMAP_OHCI_NAME		"omap-ohci"
+#define OMAP_OHCI_BASE		0xfffba000
+#define OMAP_OHCI_SIZE		4096
+
+#define HMC_CLEAR		(0x3f << 1)
+#define APLL_NDPLL_SWITCH	0x0001
+#define DPLL_PLL_ENABLE		0x0010
+#define DPLL_LOCK		0x0001
+#define SOFT_REQ_REG_REQ	0x0001
+#define USB_MCLK_EN		0x0010
+#define USB_HOST_HHC_UHOST_EN	0x00000200
+#define SOFT_USB_OTG_REQ	(1 << 8)
+#define SOFT_USB_REQ		(1 << 3)
+#define STATUS_REQ_REG		0xfffe0840
+#define USB_HOST_DPLL_REQ	(1 << 8)
+#define SOFT_DPLL_REQ		(1 << 0)
+
+/* OMAP-1510 USB OHCI defines */
+#define OMAP1510_LB_MEMSIZE	32		/* Should be same as SDRAM size */
+#define OMAP1510_LB_CLOCK_DIV	0xfffec10c
+#define OMAP1510_LB_MMU_CTL	0xfffec208	
+#define OMAP1510_LB_MMU_LCK	0xfffec224
+#define OMAP1510_LB_MMU_LD_TLB	0xfffec228
+#define OMAP1510_LB_MMU_CAM_H	0xfffec22c
+#define OMAP1510_LB_MMU_CAM_L	0xfffec230
+#define OMAP1510_LB_MMU_RAM_H	0xfffec234
+#define OMAP1510_LB_MMU_RAM_L	0xfffec238
+
+/* OMAP-1610 USB OHCI defines */
+#define USB_TRANSCEIVER_CTRL	0xfffe1064
+#define OTG_REV			0xfffb0400
+
+#define OTG_SYSCON_1		0xfffb0404
+#define OTG_IDLE_EN		(1 << 15)
+#define DEV_IDLE_EN		(1 << 13)
+
+#define OTG_SYSCON_2		0xfffb0408
+#define OTG_CTRL		0xfffb040c
+#define OTG_IRQ_EN		0xfffb0410
+#define OTG_IRQ_SRC		0xfffb0414
+
+#define OTG_EN			(1 << 31)
+#define USBX_SYNCHRO		(1 << 30)
+#define SRP_VBUS		(1 << 12)
+#define OTG_PADEN		(1 << 10)
+#define HMC_PADEN		(1 << 9)
+#define UHOST_EN		(1 << 8)
+
+/* Hardware specific defines */
+#define OMAP1510_FPGA_HOST_CTRL	0xe800020c

drivers/usb/media/dabusb.c

@@ -781,17 +781,25 @@ static int dabusb_probe (struct usb_interface *intf,
 
 static void dabusb_disconnect (struct usb_interface *intf)
 {
+	wait_queue_t __wait;
 	pdabusb_t s = usb_get_intfdata (intf);
 
 	dbg("dabusb_disconnect");
-
+	
+	init_waitqueue_entry(&__wait, current);
+	
 	usb_set_intfdata (intf, NULL);
 	if (s) {
 		usb_deregister_dev (intf, &dabusb_class);
 		s->remove_pending = 1;
 		wake_up (&s->wait);
+		add_wait_queue(&s->remove_ok, &__wait);
+		set_current_state(TASK_UNINTERRUPTIBLE);
 		if (s->state == _started)
-			sleep_on (&s->remove_ok);
+			schedule();
+		current->state = TASK_RUNNING;
+		remove_wait_queue(&s->remove_ok, &__wait);
+		
 		s->usbdev = NULL;
 		s->overruns = 0;
 	}

drivers/usb/misc/Kconfig

@@ -6,6 +6,7 @@ comment "USB Miscellaneous drivers"
 
 config USB_EMI62
 	tristate "EMI 6|2m USB Audio interface support"
+	depends on USB
 	---help---
 	  This driver loads firmware to Emagic EMI 6|2m low latency USB
 	  Audio and Midi interface.
@@ -20,6 +21,7 @@ config USB_EMI62
 
 config USB_EMI26
 	tristate "EMI 2|6 USB Audio interface support"
+	depends on USB
 	---help---
 	  This driver loads firmware to Emagic EMI 2|6 low latency USB
 	  Audio interface.

drivers/usb/misc/auerswald.c

@@ -1927,7 +1927,6 @@ static int auerswald_probe (struct usb_interface *intf,
 {
 	struct usb_device *usbdev = interface_to_usbdev(intf);
 	pauerswald_t cp = NULL;
-	DECLARE_WAIT_QUEUE_HEAD (wqh);
 	unsigned int u = 0;
 	char *pbuf;
 	int ret;
@@ -1975,7 +1974,8 @@ static int auerswald_probe (struct usb_interface *intf,
 	dbg ("Version is %X", cp->version);
 
 	/* allow some time to settle the device */
-	sleep_on_timeout (&wqh, HZ / 3 );
+	set_current_state(TASK_UNINTERRUPTIBLE);
+	schedule_timeout(HZ/3);
 
 	/* Try to get a suitable textual description of the device */
 	/* Device name:*/

drivers/usb/misc/tiglusb.c

@@ -161,7 +161,7 @@ tiglusb_read (struct file *filp, char __user *buf, size_t count, loff_t * f_pos)
 	int bytes_to_read = 0;
 	int bytes_read = 0;
 	int result = 0;
-	char buffer[BULK_RCV_MAX];
+	char *buffer;
 	unsigned int pipe;
 
 	if (*f_pos)
@@ -173,6 +173,10 @@ tiglusb_read (struct file *filp, char __user *buf, size_t count, loff_t * f_pos)
 	if (!s->dev)
 		return -EIO;
 
+	buffer = kmalloc(BULK_RCV_MAX, GFP_KERNEL);
+	if (!buffer)
+		return -ENOMEM;
+
 	bytes_to_read = (count >= BULK_RCV_MAX) ? BULK_RCV_MAX : count;
 
 	pipe = usb_rcvbulkpipe (s->dev, 1);
@@ -203,6 +207,7 @@ tiglusb_read (struct file *filp, char __user *buf, size_t count, loff_t * f_pos)
 	}
 
       out:
+	kfree(buffer);
 	return ret ? ret : bytes_read;
 }
 
@@ -214,7 +219,7 @@ tiglusb_write (struct file *filp, const char __user *buf, size_t count, loff_t *
 	int bytes_to_write = 0;
 	int bytes_written = 0;
 	int result = 0;
-	char buffer[BULK_SND_MAX];
+	char *buffer;
 	unsigned int pipe;
 
 	if (*f_pos)
@@ -226,6 +231,10 @@ tiglusb_write (struct file *filp, const char __user *buf, size_t count, loff_t *
 	if (!s->dev)
 		return -EIO;
 
+	buffer = kmalloc(BULK_SND_MAX, GFP_KERNEL);
+	if (!buffer)
+		return -ENOMEM;
+
 	bytes_to_write = (count >= BULK_SND_MAX) ? BULK_SND_MAX : count;
 	if (copy_from_user (buffer, buf, bytes_to_write)) {
 		ret = -EFAULT;
@@ -258,6 +267,7 @@ tiglusb_write (struct file *filp, const char __user *buf, size_t count, loff_t *
 	}
 
       out:
+	kfree(buffer);
 	return ret ? ret : bytes_written;
 }
 
@@ -387,7 +397,11 @@ tiglusb_probe (struct usb_interface *intf,
 static void
 tiglusb_disconnect (struct usb_interface *intf)
 {
+	wait_queue_t __wait;
 	ptiglusb_t s = usb_get_intfdata (intf);
+	
+	init_waitqueue_entry(&__wait, current);
+	
 
 	usb_set_intfdata (intf, NULL);
 	if (!s || !s->dev) {
@@ -397,8 +411,12 @@ tiglusb_disconnect (struct usb_interface *intf)
 
 	s->remove_pending = 1;
 	wake_up (&s->wait);
+	add_wait_queue(&s->wait, &__wait);
+	set_current_state(TASK_UNINTERRUPTIBLE);
 	if (s->state == _started)
-		sleep_on (&s->remove_ok);
+		schedule();
+	current->state = TASK_RUNNING;
+	remove_wait_queue(&s->wait, &__wait);
 	down (&s->mutex);
 	s->dev = NULL;
 	s->opened = 0;

drivers/usb/serial/kobil_sct.c

@@ -651,7 +651,7 @@ static int  kobil_ioctl(struct usb_serial_port *port, struct file *file,
 		return 0;
 
 	case TCSETS:   // 0x5402
-		if (! &port->tty->termios) {
+		if (!(port->tty->termios)) {
 			dbg("%s - port %d Error: port->tty->termios is NULL", __FUNCTION__, port->number);
 			return -ENOTTY;
 		}

drivers/usb/serial/whiteheat.c

@@ -353,8 +353,8 @@ static int whiteheat_attach (struct usb_serial *serial)
 	int pipe;
 	int ret;
 	int alen;
-	__u8 command[2] = { WHITEHEAT_GET_HW_INFO, 0 };
-	__u8 result[sizeof(*hw_info) + 1];
+	__u8 *command;
+	__u8 *result;
 	int i;
 	int j;
 	struct urb *urb;
@@ -365,13 +365,22 @@ static int whiteheat_attach (struct usb_serial *serial)
 	command_port = serial->port[COMMAND_PORT];
 
 	pipe = usb_sndbulkpipe (serial->dev, command_port->bulk_out_endpointAddress);
+	command = kmalloc(2, GFP_KERNEL);
+	if (!command)
+		goto no_command_buffer;
+	command[0] = WHITEHEAT_GET_HW_INFO;
+	command[1] = 0;
+	
+	result = kmalloc(sizeof(*hw_info) + 1, GFP_KERNEL);
+	if (!result)
+		goto no_result_buffer;
 	/*
 	 * When the module is reloaded the firmware is still there and
 	 * the endpoints are still in the usb core unchanged. This is the
          * unlinking bug in disguise. Same for the call below.
          */
 	usb_clear_halt(serial->dev, pipe);
-	ret = usb_bulk_msg (serial->dev, pipe, command, sizeof(command), &alen, COMMAND_TIMEOUT);
+	ret = usb_bulk_msg (serial->dev, pipe, command, 2, &alen, COMMAND_TIMEOUT);
 	if (ret) {
 		err("%s: Couldn't send command [%d]", serial->type->name, ret);
 		goto no_firmware;
@@ -383,7 +392,7 @@ static int whiteheat_attach (struct usb_serial *serial)
 	pipe = usb_rcvbulkpipe (serial->dev, command_port->bulk_in_endpointAddress);
 	/* See the comment on the usb_clear_halt() above */
 	usb_clear_halt(serial->dev, pipe);
-	ret = usb_bulk_msg (serial->dev, pipe, result, sizeof(result), &alen, COMMAND_TIMEOUT);
+	ret = usb_bulk_msg (serial->dev, pipe, result, sizeof(*hw_info) + 1, &alen, COMMAND_TIMEOUT);
 	if (ret) {
 		err("%s: Couldn't get results [%d]", serial->type->name, ret);
 		goto no_firmware;
@@ -485,6 +494,8 @@ static int whiteheat_attach (struct usb_serial *serial)
 	usb_set_serial_port_data(command_port, command_info);
 	command_port->write_urb->complete = command_port_write_callback;
 	command_port->read_urb->complete = command_port_read_callback;
+	kfree(result);
+	kfree(command);
 
 	return 0;
 
@@ -526,6 +537,10 @@ static int whiteheat_attach (struct usb_serial *serial)
 no_private:
 		;
 	}
+	kfree(result);
+no_result_buffer:
+	kfree(command);
+no_command_buffer:
 	return -ENOMEM;
 }
 

drivers/usb/storage/scsiglue.c

@@ -309,44 +309,6 @@ static int proc_info (struct Scsi_Host *hostptr, char *buffer, char **start, off
  * Sysfs interface
  ***********************************************************************/
 
-/* Output routine for the sysfs info file */
-static ssize_t show_info(struct device *dev, char *buffer)
-{
-	char *pos = buffer;
-	const int length = PAGE_SIZE;
-
-	struct scsi_device *sdev = to_scsi_device(dev);
-	struct us_data *us = (struct us_data*)sdev->host->hostdata[0];
-
-	/* print the controller name */
-	SPRINTF("   Host scsi%d: usb-storage\n", sdev->host->host_no);
-
-	/* print product, vendor, and serial number strings */
-	SPRINTF("       Vendor: %s\n", us->vendor);
-	SPRINTF("      Product: %s\n", us->product);
-	SPRINTF("Serial Number: %s\n", us->serial);
-
-	/* show the protocol and transport */
-	SPRINTF("     Protocol: %s\n", us->protocol_name);
-	SPRINTF("    Transport: %s\n", us->transport_name);
-
-	/* show the device flags */
-	if (pos < buffer + length) {
-		pos += sprintf(pos, "       Quirks:");
-
-		DO_FLAG(SINGLE_LUN);
-		DO_FLAG(SCM_MULT_TARG);
-		DO_FLAG(FIX_INQUIRY);
-		DO_FLAG(FIX_CAPACITY);
-
-		*(pos++) = '\n';
-	}
-
-	return (pos - buffer);
-}
-
-static DEVICE_ATTR(info, S_IRUGO, show_info, NULL);
-
 /* Output routine for the sysfs max_sectors file */
 static ssize_t show_max_sectors(struct device *dev, char *buf)
 {
@@ -373,7 +335,6 @@ static DEVICE_ATTR(max_sectors, S_IRUGO | S_IWUSR, show_max_sectors,
 		store_max_sectors);
 
 static struct device_attribute *sysfs_device_attr_list[] = {
-		&dev_attr_info,
 		&dev_attr_max_sectors,
 		NULL,
 		};

drivers/usb/storage/unusual_devs.h

@@ -115,6 +115,13 @@ UNUSUAL_DEV(  0x04a4, 0x0004, 0x0001, 0x0001,
 		"DVD-CAM DZ-MV100A Camcorder",
 		US_SC_SCSI, US_PR_CB, NULL, US_FL_SINGLE_LUN),
 
+/* Reported by Simon Levitt <simon@whattf.com>
+ * This entry needs Sub and Proto fields */
+UNUSUAL_DEV(  0x04b8, 0x0601, 0x0100, 0x0100,
+		"Epson",
+		"875DC Storage",
+		US_SC_SCSI, US_PR_CB, NULL, US_FL_FIX_INQUIRY),
+
 /* Reported by Khalid Aziz <khalid@gonehiking.org>
  * This entry is needed because the device reports Sub=ff */
 UNUSUAL_DEV(  0x04b8, 0x0602, 0x0110, 0x0110,
@@ -482,11 +489,6 @@ UNUSUAL_DEV(  0x07ab, 0xfc01, 0x0000, 0x9999,
 		"Freecom",
 		"USB-IDE",
 		US_SC_QIC, US_PR_FREECOM, freecom_init, 0),
-
-UNUSUAL_DEV(  0x07ab, 0xfc84, 0x0000, 0x9999,
-		"Freecom",
-		"FX-5/FX-50",
-		US_SC_QIC, US_PR_FREECOM, freecom_init, 0),
 #endif
 
 UNUSUAL_DEV(  0x07af, 0x0004, 0x0100, 0x0133, 

include/asm-ia64/uaccess.h

@@ -28,7 +28,7 @@
  *
  * Based on <asm-alpha/uaccess.h>.
  *
- * Copyright (C) 1998, 1999, 2001-2003 Hewlett-Packard Co
+ * Copyright (C) 1998, 1999, 2001-2004 Hewlett-Packard Co
  *	David Mosberger-Tang <davidm@hpl.hp.com>
  */
 
@@ -283,24 +283,23 @@ extern unsigned long __strnlen_user (const char *, long);
 	__su_ret;						\
 })
 
+/* Generic code can't deal with the location-relative format that we use for compactness.  */
 #define ARCH_HAS_SORT_EXTABLE
 #define ARCH_HAS_SEARCH_EXTABLE
 
 struct exception_table_entry {
-	int addr;	/* gp-relative address of insn this fixup is for */
-	int cont;	/* gp-relative continuation address; if bit 2 is set, r9 is set to 0 */
+	int addr;	/* location-relative address of insn this fixup is for */
+	int cont;	/* location-relative continuation addr.; if bit 2 is set, r9 is set to 0 */
 };
 
 extern void handle_exception (struct pt_regs *regs, const struct exception_table_entry *e);
 extern const struct exception_table_entry *search_exception_tables (unsigned long addr);
 
-# define SEARCH_EXCEPTION_TABLE(regs) search_exception_tables(regs->cr_iip + ia64_psr(regs)->ri)
-
 static inline int
 done_with_exception (struct pt_regs *regs)
 {
 	const struct exception_table_entry *e;
-	e = SEARCH_EXCEPTION_TABLE(regs);
+	e = search_exception_tables(regs->cr_iip + ia64_psr(regs)->ri);
 	if (e) {
 		handle_exception(regs, e);
 		return 1;

include/linux/usb.h

@@ -856,7 +856,6 @@ extern int usb_bulk_msg(struct usb_device *usb_dev, unsigned int pipe,
 /* wrappers around usb_control_msg() for the most common standard requests */
 extern int usb_get_descriptor(struct usb_device *dev, unsigned char desctype,
 	unsigned char descindex, void *buf, int size);
-extern int usb_get_device_descriptor(struct usb_device *dev);
 extern int usb_get_status(struct usb_device *dev,
 	int type, int target, void *data);
 extern int usb_get_string(struct usb_device *dev,

kernel/power/pmdisk.c

@@ -28,6 +28,7 @@
 #include <linux/device.h>
 #include <linux/swapops.h>
 #include <linux/bootmem.h>
+#include <linux/utsname.h>
 
 #include <asm/mmu_context.h>
 

kernel/sched.c

@@ -124,9 +124,6 @@
 	(NS_TO_JIFFIES((p)->sleep_avg) * MAX_BONUS / \
 		MAX_SLEEP_AVG)
 
-/* spinlock debugging needs this, even on !CONFIG_SMP */
-spinlock_t kernel_flag __cacheline_aligned_in_smp = SPIN_LOCK_UNLOCKED;
-
 #ifdef CONFIG_SMP
 #define TIMESLICE_GRANULARITY(p)	(MIN_TIMESLICE * \
 		(1 << (((MAX_BONUS - CURRENT_BONUS(p)) ? : 1) - 1)) * \
@@ -2859,7 +2856,6 @@ __init int migration_init(void)
 
 #endif
 
-#if defined(CONFIG_SMP) || defined(CONFIG_PREEMPT)
 /*
  * The 'big kernel lock'
  *
@@ -2869,10 +2865,11 @@ __init int migration_init(void)
  * been migrated to a proper locking design yet.
  *
  * Don't use in new code.
+ *
+ * Note: spinlock debugging needs this even on !CONFIG_SMP.
  */
-
+spinlock_t kernel_flag __cacheline_aligned_in_smp = SPIN_LOCK_UNLOCKED;
 EXPORT_SYMBOL(kernel_flag);
-#endif
 
 static void kstat_init_cpu(int cpu)
 {

sound/usb/usbaudio.c

@@ -33,6 +33,7 @@
 #include <linux/slab.h>
 #include <linux/string.h>
 #include <linux/usb.h>
+#include <linux/usb_ch9.h>
 #include <sound/core.h>
 #include <sound/info.h>
 #include <sound/pcm.h>
@@ -2560,9 +2561,10 @@ static int snd_usb_extigy_boot_quirk(struct usb_device *dev, struct usb_interfac
 		err = usb_control_msg(dev, usb_sndctrlpipe(dev,0),
 				      0x10, 0x43, 0x0001, 0x000a, NULL, 0, HZ);
 		if (err < 0) snd_printdd("error sending boot message: %d\n", err);
-		err = usb_get_device_descriptor(dev);
+		err = usb_get_descriptor(dev, USB_DT_DEVICE, 0,
+				&dev->descriptor, sizeof(dev->descriptor));
 		config = dev->actconfig;
-		if (err < 0) snd_printdd("error usb_get_device_descriptor: %d\n", err);
+		if (err < 0) snd_printdd("error usb_get_descriptor: %d\n", err);
 		err = usb_reset_configuration(dev);
 		if (err < 0) snd_printdd("error usb_reset_configuration: %d\n", err);
 		snd_printdd("extigy_boot: new boot length = %d\n", get_cfg_desc(config)->wTotalLength);