Commit c5d7a923 authored by Sascha Hauer's avatar Sascha Hauer

Merge branch 'features/denx-mx28' into for-arnd-features

parents d5460290 ea42a0d0
......@@ -26,6 +26,7 @@ CONFIG_MACH_MX23EVK=y
CONFIG_MACH_MX28EVK=y
CONFIG_MACH_STMP378X_DEVB=y
CONFIG_MACH_TX28=y
CONFIG_MACH_M28EVK=y
# CONFIG_ARM_THUMB is not set
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
......
......@@ -64,8 +64,25 @@ config MODULE_TX28
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXS_PWM
config MODULE_M28
bool
select SOC_IMX28
select LEDS_GPIO_REGISTER
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_FEC
select MXS_HAVE_PLATFORM_FLEXCAN
select MXS_HAVE_PLATFORM_MXS_I2C
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXSFB
select MXS_OCOTP
config MACH_TX28
bool "Ka-Ro TX28 module"
select MODULE_TX28
config MACH_M28EVK
bool "Support DENX M28EVK Platform"
select MODULE_M28
endif
......@@ -10,6 +10,7 @@ obj-$(CONFIG_SOC_IMX28) += clock-mx28.o mm-mx28.o
obj-$(CONFIG_MACH_STMP378X_DEVB) += mach-stmp378x_devb.o
obj-$(CONFIG_MACH_MX23EVK) += mach-mx23evk.o
obj-$(CONFIG_MACH_MX28EVK) += mach-mx28evk.o
obj-$(CONFIG_MACH_M28EVK) += mach-m28evk.o
obj-$(CONFIG_MODULE_TX28) += module-tx28.o
obj-$(CONFIG_MACH_TX28) += mach-tx28.o
......
......@@ -738,11 +738,17 @@ static int clk_misc_init(void)
__raw_writel(BM_CLKCTRL_CPU_INTERRUPT_WAIT,
CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU_SET);
/* Extra fec clock setting */
reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
reg &= ~BM_CLKCTRL_ENET_SLEEP;
reg |= BM_CLKCTRL_ENET_CLK_OUT_EN;
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
/*
* Extra fec clock setting
* The DENX M28 uses an external clock source
* and the clock output must not be enabled
*/
if (!machine_is_m28evk()) {
reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
reg &= ~BM_CLKCTRL_ENET_SLEEP;
reg |= BM_CLKCTRL_ENET_CLK_OUT_EN;
__raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
}
/*
* 480 MHz seems too high to be ssp clock source directly,
......
......@@ -33,6 +33,7 @@
0)
#define cpu_is_mx28() ( \
machine_is_mx28evk() || \
machine_is_m28evk() || \
machine_is_tx28() || \
0)
......
......@@ -63,6 +63,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
mxs_duart_base = MX23_DUART_BASE_ADDR;
break;
case MACH_TYPE_MX28EVK:
case MACH_TYPE_M28EVK:
case MACH_TYPE_TX28:
mxs_duart_base = MX28_DUART_BASE_ADDR;
break;
......
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment