Commit c60d1ae4 authored by Gerald Schaefer's avatar Gerald Schaefer Committed by Martin Schwidefsky

s390/pci: introduce lazy IOTLB flushing for DMA unmap

This changes the default IOTLB flushing method to lazy flushing, which
means that there will be no direct flush after each DMA unmap operation.
Instead, the iommu bitmap pointer will be adjusted after unmap, so that
no DMA address will be re-used until after an iommu bitmap wrap-around.
The only IOTLB flush will then happen after each wrap-around.

A new kernel parameter "s390_iommu=" is also introduced, to allow changing
the flushing behaviour to the old strict method.
Reviewed-by: default avatarSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: default avatarGerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: default avatarMartin Schwidefsky <schwidefsky@de.ibm.com>
parent 29b8dd9d
......@@ -3023,6 +3023,13 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
S [KNL] Run init in single mode
s390_iommu= [HW,S390]
Set s390 IOTLB flushing mode
strict
With strict flushing every unmap operation will result in
an IOTLB flush. Default is lazy flushing before reuse,
which is faster.
sa1100ir [NET]
See drivers/net/irda/sa1100_ir.c.
......
......@@ -16,6 +16,13 @@
static struct kmem_cache *dma_region_table_cache;
static struct kmem_cache *dma_page_table_cache;
static int s390_iommu_strict;
static int zpci_refresh_global(struct zpci_dev *zdev)
{
return zpci_refresh_trans((u64) zdev->fh << 32, zdev->start_dma,
zdev->iommu_pages * PAGE_SIZE);
}
static unsigned long *dma_alloc_cpu_table(void)
{
......@@ -155,18 +162,15 @@ static int dma_update_trans(struct zpci_dev *zdev, unsigned long pa,
}
/*
* rpcit is not required to establish new translations when previously
* invalid translation-table entries are validated, however it is
* required when altering previously valid entries.
* With zdev->tlb_refresh == 0, rpcit is not required to establish new
* translations when previously invalid translation-table entries are
* validated. With lazy unmap, it also is skipped for previously valid
* entries, but a global rpcit is then required before any address can
* be re-used, i.e. after each iommu bitmap wrap-around.
*/
if (!zdev->tlb_refresh &&
((flags & ZPCI_PTE_VALID_MASK) == ZPCI_PTE_VALID))
/*
* TODO: also need to check that the old entry is indeed INVALID
* and not only for one page but for the whole range...
* -> now we WARN_ON in that case but with lazy unmap that
* needs to be redone!
*/
(!s390_iommu_strict ||
((flags & ZPCI_PTE_VALID_MASK) == ZPCI_PTE_VALID)))
goto no_refresh;
rc = zpci_refresh_trans((u64) zdev->fh << 32, start_dma_addr,
......@@ -220,16 +224,21 @@ static unsigned long __dma_alloc_iommu(struct zpci_dev *zdev,
static unsigned long dma_alloc_iommu(struct zpci_dev *zdev, int size)
{
unsigned long offset, flags;
int wrap = 0;
spin_lock_irqsave(&zdev->iommu_bitmap_lock, flags);
offset = __dma_alloc_iommu(zdev, zdev->next_bit, size);
if (offset == -1)
if (offset == -1) {
/* wrap-around */
offset = __dma_alloc_iommu(zdev, 0, size);
wrap = 1;
}
if (offset != -1) {
zdev->next_bit = offset + size;
if (zdev->next_bit >= zdev->iommu_pages)
zdev->next_bit = 0;
if (!zdev->tlb_refresh && !s390_iommu_strict && wrap)
/* global flush after wrap-around with lazy unmap */
zpci_refresh_global(zdev);
}
spin_unlock_irqrestore(&zdev->iommu_bitmap_lock, flags);
return offset;
......@@ -243,7 +252,11 @@ static void dma_free_iommu(struct zpci_dev *zdev, unsigned long offset, int size
if (!zdev->iommu_bitmap)
goto out;
bitmap_clear(zdev->iommu_bitmap, offset, size);
if (offset >= zdev->next_bit)
/*
* Lazy flush for unmap: need to move next_bit to avoid address re-use
* until wrap-around.
*/
if (!s390_iommu_strict && offset >= zdev->next_bit)
zdev->next_bit = offset + size;
out:
spin_unlock_irqrestore(&zdev->iommu_bitmap_lock, flags);
......@@ -504,3 +517,12 @@ struct dma_map_ops s390_dma_ops = {
/* dma_supported is unconditionally true without a callback */
};
EXPORT_SYMBOL_GPL(s390_dma_ops);
static int __init s390_iommu_setup(char *str)
{
if (!strncmp(str, "strict", 6))
s390_iommu_strict = 1;
return 0;
}
__setup("s390_iommu=", s390_iommu_setup);
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment