RDMA/mlx5: Allow SQ modification

Currently the SQ is set to a ready state when the RAW QP is modified to
INIT.  When the TIS is modified, e.g. to change the lag_tx_affinity, then
SQs which are already in the ready state will not be affected.

Open a window to modify the SQ behavior by setting the SQ as ready only
when QP was modified to RTS.

Link: https://lore.kernel.org/r/20200716105416.1423826-1-leon@kernel.orgSigned-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Zhang <markz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

drivers/infiniband/hw/mlx5/qp.c

@@ -3544,7 +3544,7 @@ static int modify_raw_packet_qp(struct mlx5_ib_dev *dev, struct mlx5_ib_qp *qp,
 	switch (raw_qp_param->operation) {
 	case MLX5_CMD_OP_RST2INIT_QP:
 		rq_state = MLX5_RQC_STATE_RDY;
-		sq_state = MLX5_SQC_STATE_RDY;
+		sq_state = MLX5_SQC_STATE_RST;
 		break;
 	case MLX5_CMD_OP_2ERR_QP:
 		rq_state = MLX5_RQC_STATE_ERR;
@@ -3556,13 +3556,11 @@ static int modify_raw_packet_qp(struct mlx5_ib_dev *dev, struct mlx5_ib_qp *qp,
 		break;
 	case MLX5_CMD_OP_RTR2RTS_QP:
 	case MLX5_CMD_OP_RTS2RTS_QP:
-		if (raw_qp_param->set_mask ==
-		    MLX5_RAW_QP_RATE_LIMIT) {
-			modify_rq = 0;
-			sq_state = sq->state;
-		} else {
-			return raw_qp_param->set_mask ? -EINVAL : 0;
-		}
+		if (raw_qp_param->set_mask & ~MLX5_RAW_QP_RATE_LIMIT)
+			return -EINVAL;
+
+		modify_rq = 0;
+		sq_state = MLX5_SQC_STATE_RDY;
 		break;
 	case MLX5_CMD_OP_INIT2INIT_QP:
 	case MLX5_CMD_OP_INIT2RTR_QP:
@@ -4443,7 +4441,7 @@ static int sqrq_state_to_qp_state(u8 sq_state, u8 rq_state,
 			[MLX5_SQ_STATE_NA]	= IB_QPS_RESET,
 		},
 		[MLX5_RQC_STATE_RDY] = {
-			[MLX5_SQC_STATE_RST]	= MLX5_QP_STATE_BAD,
+			[MLX5_SQC_STATE_RST]	= MLX5_QP_STATE,
 			[MLX5_SQC_STATE_RDY]	= MLX5_QP_STATE,
 			[MLX5_SQC_STATE_ERR]	= IB_QPS_SQE,
 			[MLX5_SQ_STATE_NA]	= MLX5_QP_STATE,
@@ -4455,7 +4453,7 @@ static int sqrq_state_to_qp_state(u8 sq_state, u8 rq_state,
 			[MLX5_SQ_STATE_NA]	= IB_QPS_ERR,
 		},
 		[MLX5_RQ_STATE_NA] = {
-			[MLX5_SQC_STATE_RST]    = IB_QPS_RESET,
+			[MLX5_SQC_STATE_RST]    = MLX5_QP_STATE,
 			[MLX5_SQC_STATE_RDY]	= MLX5_QP_STATE,
 			[MLX5_SQC_STATE_ERR]	= MLX5_QP_STATE,
 			[MLX5_SQ_STATE_NA]	= MLX5_QP_STATE_BAD,