cy82c693: remove no longer needed debugging code

Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent 7ca70e4d
......@@ -50,11 +50,6 @@
#define DRV_NAME "cy82c693"
/*
* The following are used to debug the driver.
*/
#define CY82C693_DEBUG_INFO 0
/*
* NOTE: the value for busmaster timeout is tricky and I got it by
* trial and error! By using a to low value will cause DMA timeouts
......@@ -176,11 +171,6 @@ static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode)
outb(index, CY82_INDEX_PORT);
outb(data, CY82_DATA_PORT);
#if CY82C693_DEBUG_INFO
printk(KERN_INFO "%s (ch=%d, dev=%d): set DMA mode to %d (single=%d)\n",
drive->name, hwif->channel, drive->dn & 1, mode & 3, single);
#endif /* CY82C693_DEBUG_INFO */
/*
* note: below we set the value for Bus Master IDE TimeOut Register
* I'm not absolutly sure what this does, but it solved my problem
......@@ -194,11 +184,6 @@ static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode)
data = BUSMASTER_TIMEOUT;
outb(CY82_INDEX_TIMEOUT, CY82_INDEX_PORT);
outb(data, CY82_DATA_PORT);
#if CY82C693_DEBUG_INFO
printk(KERN_INFO "%s: Set IDE Bus Master TimeOut Register to 0x%X\n",
drive->name, data);
#endif /* CY82C693_DEBUG_INFO */
}
static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
......@@ -239,8 +224,6 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r);
pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w);
pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8);
addrCtrl &= 0xF;
} else {
/*
* set slave drive
......@@ -257,17 +240,7 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r);
pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w);
pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8);
addrCtrl >>= 4;
addrCtrl &= 0xF;
}
#if CY82C693_DEBUG_INFO
printk(KERN_INFO "%s (ch=%d, dev=%d): set PIO timing to "
"(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n",
drive->name, hwif->channel, drive->dn & 1,
addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
#endif /* CY82C693_DEBUG_INFO */
}
static void __devinit init_iops_cy82c693(ide_hwif_t *hwif)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment