Commit d1a277c5 authored by Wolfgang Grandegger's avatar Wolfgang Grandegger Committed by David S. Miller

can: sja1000: generic OF platform bus driver

This patch adds a generic driver for SJA1000 chips on the OpenFirmware
platform bus found on embedded PowerPC systems. You need a SJA1000 node
definition in your flattened device tree source (DTS) file similar to:

  can@3,100 {
  	compatible = "nxp,sja1000";
  	reg = <3 0x100 0x80>;
  	interrupts = <2 0>;
  	interrupt-parent = <&mpic>;
  	nxp,external-clock-frequency = <16000000>;
  };

See also Documentation/powerpc/dts-bindings/can/sja1000.txt.

CC: devicetree-discuss@ozlabs.org
Signed-off-by: default avatarWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 255a9154
Memory mapped SJA1000 CAN controller from NXP (formerly Philips)
Required properties:
- compatible : should be "nxp,sja1000".
- reg : should specify the chip select, address offset and size required
to map the registers of the SJA1000. The size is usually 0x80.
- interrupts: property with a value describing the interrupt source
(number and sensitivity) required for the SJA1000.
Optional properties:
- nxp,external-clock-frequency : Frequency of the external oscillator
clock in Hz. Note that the internal clock frequency used by the
SJA1000 is half of that value. If not specified, a default value
of 16000000 (16 MHz) is used.
- nxp,tx-output-mode : operation mode of the TX output control logic:
<0x0> : bi-phase output mode
<0x1> : normal output mode (default)
<0x2> : test output mode
<0x3> : clock output mode
- nxp,tx-output-config : TX output pin configuration:
<0x01> : TX0 invert
<0x02> : TX0 pull-down (default)
<0x04> : TX0 pull-up
<0x06> : TX0 push-pull
<0x08> : TX1 invert
<0x10> : TX1 pull-down
<0x20> : TX1 pull-up
<0x30> : TX1 push-pull
- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin.
If not specified or if the specified value is 0, the CLKOUT pin
will be disabled.
- nxp,no-comparator-bypass : Allows to disable the CAN input comperator.
For futher information, please have a look to the SJA1000 data sheet.
Examples:
can@3,100 {
compatible = "nxp,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 0>;
interrupt-parent = <&mpic>;
nxp,external-clock-frequency = <16000000>;
};
......@@ -51,6 +51,15 @@ config CAN_SJA1000_PLATFORM
boards from Phytec (http://www.phytec.de) like the PCM027,
PCM038.
config CAN_SJA1000_OF_PLATFORM
depends on CAN_SJA1000 && PPC_OF
tristate "Generic OF Platform Bus based SJA1000 driver"
---help---
This driver adds support for the SJA1000 chips connected to
the OpenFirmware "platform bus" found on embedded systems with
OpenFirmware bindings, e.g. if you have a PowerPC based system
you may want to enable this option.
config CAN_EMS_PCI
tristate "EMS CPC-PCI and CPC-PCIe Card"
depends on PCI && CAN_SJA1000
......
......@@ -4,6 +4,7 @@
obj-$(CONFIG_CAN_SJA1000) += sja1000.o
obj-$(CONFIG_CAN_SJA1000_PLATFORM) += sja1000_platform.o
obj-$(CONFIG_CAN_SJA1000_OF_PLATFORM) += sja1000_of_platform.o
obj-$(CONFIG_CAN_EMS_PCI) += ems_pci.o
obj-$(CONFIG_CAN_KVASER_PCI) += kvaser_pci.o
......
/*
* Driver for SJA1000 CAN controllers on the OpenFirmware platform bus
*
* Copyright (C) 2008-2009 Wolfgang Grandegger <wg@grandegger.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the version 2 of the GNU General Public License
* as published by the Free Software Foundation
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software Foundation,
* Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*/
/* This is a generic driver for SJA1000 chips on the OpenFirmware platform
* bus found on embedded PowerPC systems. You need a SJA1000 CAN node
* definition in your flattened device tree source (DTS) file similar to:
*
* can@3,100 {
* compatible = "nxp,sja1000";
* reg = <3 0x100 0x80>;
* interrupts = <2 0>;
* interrupt-parent = <&mpic>;
* nxp,external-clock-frequency = <16000000>;
* };
*
* See "Documentation/powerpc/dts-bindings/can/sja1000.txt" for further
* information.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/netdevice.h>
#include <linux/delay.h>
#include <linux/can.h>
#include <linux/can/dev.h>
#include <linux/of_platform.h>
#include <asm/prom.h>
#include "sja1000.h"
#define DRV_NAME "sja1000_of_platform"
MODULE_AUTHOR("Wolfgang Grandegger <wg@grandegger.com>");
MODULE_DESCRIPTION("Socket-CAN driver for SJA1000 on the OF platform bus");
MODULE_LICENSE("GPL v2");
#define SJA1000_OFP_CAN_CLOCK (16000000 / 2)
#define SJA1000_OFP_OCR OCR_TX0_PULLDOWN
#define SJA1000_OFP_CDR (CDR_CBP | CDR_CLK_OFF)
static u8 sja1000_ofp_read_reg(const struct sja1000_priv *priv, int reg)
{
return in_8(priv->reg_base + reg);
}
static void sja1000_ofp_write_reg(const struct sja1000_priv *priv,
int reg, u8 val)
{
out_8(priv->reg_base + reg, val);
}
static int __devexit sja1000_ofp_remove(struct of_device *ofdev)
{
struct net_device *dev = dev_get_drvdata(&ofdev->dev);
struct sja1000_priv *priv = netdev_priv(dev);
struct device_node *np = ofdev->node;
struct resource res;
dev_set_drvdata(&ofdev->dev, NULL);
unregister_sja1000dev(dev);
free_sja1000dev(dev);
iounmap(priv->reg_base);
irq_dispose_mapping(dev->irq);
of_address_to_resource(np, 0, &res);
release_mem_region(res.start, resource_size(&res));
return 0;
}
static int __devinit sja1000_ofp_probe(struct of_device *ofdev,
const struct of_device_id *id)
{
struct device_node *np = ofdev->node;
struct net_device *dev;
struct sja1000_priv *priv;
struct resource res;
const u32 *prop;
int err, irq, res_size, prop_size;
void __iomem *base;
err = of_address_to_resource(np, 0, &res);
if (err) {
dev_err(&ofdev->dev, "invalid address\n");
return err;
}
res_size = resource_size(&res);
if (!request_mem_region(res.start, res_size, DRV_NAME)) {
dev_err(&ofdev->dev, "couldn't request %#x..%#x\n",
res.start, res.end);
return -EBUSY;
}
base = ioremap_nocache(res.start, res_size);
if (!base) {
dev_err(&ofdev->dev, "couldn't ioremap %#x..%#x\n",
res.start, res.end);
err = -ENOMEM;
goto exit_release_mem;
}
irq = irq_of_parse_and_map(np, 0);
if (irq == NO_IRQ) {
dev_err(&ofdev->dev, "no irq found\n");
err = -ENODEV;
goto exit_unmap_mem;
}
dev = alloc_sja1000dev(0);
if (!dev) {
err = -ENOMEM;
goto exit_dispose_irq;
}
priv = netdev_priv(dev);
priv->read_reg = sja1000_ofp_read_reg;
priv->write_reg = sja1000_ofp_write_reg;
prop = of_get_property(np, "nxp,external-clock-frequency", &prop_size);
if (prop && (prop_size == sizeof(u32)))
priv->can.clock.freq = *prop / 2;
else
priv->can.clock.freq = SJA1000_OFP_CAN_CLOCK; /* default */
prop = of_get_property(np, "nxp,tx-output-mode", &prop_size);
if (prop && (prop_size == sizeof(u32)))
priv->ocr |= *prop & OCR_MODE_MASK;
else
priv->ocr |= OCR_MODE_NORMAL; /* default */
prop = of_get_property(np, "nxp,tx-output-config", &prop_size);
if (prop && (prop_size == sizeof(u32)))
priv->ocr |= (*prop << OCR_TX_SHIFT) & OCR_TX_MASK;
else
priv->ocr |= OCR_TX0_PULLDOWN; /* default */
prop = of_get_property(np, "nxp,clock-out-frequency", &prop_size);
if (prop && (prop_size == sizeof(u32)) && *prop) {
u32 divider = priv->can.clock.freq * 2 / *prop;
if (divider > 1)
priv->cdr |= divider / 2 - 1;
else
priv->cdr |= CDR_CLKOUT_MASK;
} else {
priv->cdr |= CDR_CLK_OFF; /* default */
}
prop = of_get_property(np, "nxp,no-comparator-bypass", NULL);
if (!prop)
priv->cdr |= CDR_CBP; /* default */
priv->irq_flags = IRQF_SHARED;
priv->reg_base = base;
dev->irq = irq;
dev_info(&ofdev->dev,
"reg_base=0x%p irq=%d clock=%d ocr=0x%02x cdr=0x%02x\n",
priv->reg_base, dev->irq, priv->can.clock.freq,
priv->ocr, priv->cdr);
dev_set_drvdata(&ofdev->dev, dev);
SET_NETDEV_DEV(dev, &ofdev->dev);
err = register_sja1000dev(dev);
if (err) {
dev_err(&ofdev->dev, "registering %s failed (err=%d)\n",
DRV_NAME, err);
goto exit_free_sja1000;
}
return 0;
exit_free_sja1000:
free_sja1000dev(dev);
exit_dispose_irq:
irq_dispose_mapping(irq);
exit_unmap_mem:
iounmap(base);
exit_release_mem:
release_mem_region(res.start, res_size);
return err;
}
static struct of_device_id __devinitdata sja1000_ofp_table[] = {
{.compatible = "nxp,sja1000"},
{},
};
static struct of_platform_driver sja1000_ofp_driver = {
.owner = THIS_MODULE,
.name = DRV_NAME,
.probe = sja1000_ofp_probe,
.remove = __devexit_p(sja1000_ofp_remove),
.match_table = sja1000_ofp_table,
};
static int __init sja1000_ofp_init(void)
{
return of_register_platform_driver(&sja1000_ofp_driver);
}
module_init(sja1000_ofp_init);
static void __exit sja1000_ofp_exit(void)
{
return of_unregister_platform_driver(&sja1000_ofp_driver);
};
module_exit(sja1000_ofp_exit);
......@@ -13,6 +13,7 @@
#define OCR_MODE_TEST 0x01
#define OCR_MODE_NORMAL 0x02
#define OCR_MODE_CLOCK 0x03
#define OCR_MODE_MASK 0x07
#define OCR_TX0_INVERT 0x04
#define OCR_TX0_PULLDOWN 0x08
#define OCR_TX0_PULLUP 0x10
......@@ -21,6 +22,8 @@
#define OCR_TX1_PULLDOWN 0x40
#define OCR_TX1_PULLUP 0x80
#define OCR_TX1_PUSHPULL 0xc0
#define OCR_TX_MASK 0xfc
#define OCR_TX_SHIFT 2
struct sja1000_platform_data {
u32 clock; /* CAN bus oscillator frequency in Hz */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment