drm/amd/powerplay: Add EEPROM I2C read/write support to Arcturus.

The communication is done through SMU table and hence the code
is in powerplay.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drivers/gpu/drm/amd/powerplay/arcturus_ppt.c

@@ -37,6 +37,11 @@
 #include "smu_v11_0_pptable.h"
 #include "arcturus_ppsmc.h"
 #include "nbio/nbio_7_4_sh_mask.h"
+#include <linux/i2c.h>
+#include <linux/pci.h>
+#include "amdgpu_ras.h"
+
+#define to_amdgpu_device(x) (container_of(x, struct amdgpu_ras, eeprom_control.eeprom_accessor))->adev
 
 #define CTF_OFFSET_EDGE			5
 #define CTF_OFFSET_HOTSPOT		5
@@ -172,6 +177,7 @@ static struct smu_11_0_cmn2aisc_mapping arcturus_table_map[SMU_TABLE_COUNT] = {
 	TAB_MAP(SMU_METRICS),
 	TAB_MAP(DRIVER_SMU_CONFIG),
 	TAB_MAP(OVERDRIVE),
+	TAB_MAP(I2C_COMMANDS),
 };
 
 static struct smu_11_0_cmn2aisc_mapping arcturus_pwr_src_map[SMU_POWER_SOURCE_COUNT] = {
@@ -294,6 +300,9 @@ static int arcturus_tables_init(struct smu_context *smu, struct smu_table *table
 	SMU_TABLE_INIT(tables, SMU_TABLE_SMU_METRICS, sizeof(SmuMetrics_t),
 		       PAGE_SIZE, AMDGPU_GEM_DOMAIN_VRAM);
 
+	SMU_TABLE_INIT(tables, SMU_TABLE_I2C_COMMANDS, sizeof(SwI2cRequest_t),
+			       PAGE_SIZE, AMDGPU_GEM_DOMAIN_VRAM);
+
 	smu_table->metrics_table = kzalloc(sizeof(SmuMetrics_t), GFP_KERNEL);
 	if (!smu_table->metrics_table)
 		return -ENOMEM;
@@ -1925,6 +1934,224 @@ static int arcturus_dpm_set_uvd_enable(struct smu_context *smu, bool enable)
 	return ret;
 }
 
+
+static void arcturus_fill_eeprom_i2c_req(SwI2cRequest_t  *req, bool write,
+				  uint8_t address, uint32_t numbytes,
+				  uint8_t *data)
+{
+	int i;
+
+	BUG_ON(numbytes > MAX_SW_I2C_COMMANDS);
+
+	req->I2CcontrollerPort = 0;
+	req->I2CSpeed = 2;
+	req->SlaveAddress = address;
+	req->NumCmds = numbytes;
+
+	for (i = 0; i < numbytes; i++) {
+		SwI2cCmd_t *cmd =  &req->SwI2cCmds[i];
+
+		/* First 2 bytes are always write for lower 2b EEPROM address */
+		if (i < 2)
+			cmd->Cmd = 1;
+		else
+			cmd->Cmd = write;
+
+
+		/* Add RESTART for read  after address filled */
+		cmd->CmdConfig |= (i == 2 && !write) ? CMDCONFIG_RESTART_MASK : 0;
+
+		/* Add STOP in the end */
+		cmd->CmdConfig |= (i == (numbytes - 1)) ? CMDCONFIG_STOP_MASK : 0;
+
+		/* Fill with data regardless if read or write to simplify code */
+		cmd->RegisterAddr = data[i];
+	}
+}
+
+static int arcturus_i2c_eeprom_read_data(struct i2c_adapter *control,
+					       uint8_t address,
+					       uint8_t *data,
+					       uint32_t numbytes)
+{
+	uint32_t  i, ret = 0;
+	SwI2cRequest_t req;
+	struct amdgpu_device *adev = to_amdgpu_device(control);
+	struct smu_table_context *smu_table = &adev->smu.smu_table;
+	struct smu_table *table = &smu_table->tables[SMU_TABLE_I2C_COMMANDS];
+
+	memset(&req, 0, sizeof(req));
+	arcturus_fill_eeprom_i2c_req(&req, false, address, numbytes, data);
+
+	mutex_lock(&adev->smu.mutex);
+	/* Now read data starting with that address */
+	ret = smu_update_table(&adev->smu, SMU_TABLE_I2C_COMMANDS, 0, &req,
+					true);
+	mutex_unlock(&adev->smu.mutex);
+
+	if (!ret) {
+		SwI2cRequest_t *res = (SwI2cRequest_t *)table->cpu_addr;
+
+		/* Assume SMU  fills res.SwI2cCmds[i].Data with read bytes */
+		for (i = 0; i < numbytes; i++)
+			data[i] = res->SwI2cCmds[i].Data;
+
+		pr_debug("arcturus_i2c_eeprom_read_data, address = %x, bytes = %d, data :",
+				  (uint16_t)address, numbytes);
+
+		print_hex_dump(KERN_DEBUG, "data: ", DUMP_PREFIX_NONE,
+			       8, 1, data, numbytes, false);
+	} else
+		pr_err("arcturus_i2c_eeprom_read_data - error occurred :%x", ret);
+
+	return ret;
+}
+
+static int arcturus_i2c_eeprom_write_data(struct i2c_adapter *control,
+						uint8_t address,
+						uint8_t *data,
+						uint32_t numbytes)
+{
+	uint32_t ret;
+	SwI2cRequest_t req;
+	struct amdgpu_device *adev = to_amdgpu_device(control);
+
+	memset(&req, 0, sizeof(req));
+	arcturus_fill_eeprom_i2c_req(&req, true, address, numbytes, data);
+
+	mutex_lock(&adev->smu.mutex);
+	ret = smu_update_table(&adev->smu, SMU_TABLE_I2C_COMMANDS, 0, &req, true);
+	mutex_unlock(&adev->smu.mutex);
+
+	if (!ret) {
+		pr_debug("arcturus_i2c_write(), address = %x, bytes = %d , data: ",
+					 (uint16_t)address, numbytes);
+
+		print_hex_dump(KERN_DEBUG, "data: ", DUMP_PREFIX_NONE,
+			       8, 1, data, numbytes, false);
+		/*
+		 * According to EEPROM spec there is a MAX of 10 ms required for
+		 * EEPROM to flush internal RX buffer after STOP was issued at the
+		 * end of write transaction. During this time the EEPROM will not be
+		 * responsive to any more commands - so wait a bit more.
+		 */
+		msleep(10);
+
+	} else
+		pr_err("arcturus_i2c_write- error occurred :%x", ret);
+
+	return ret;
+}
+
+static int arcturus_i2c_eeprom_i2c_xfer(struct i2c_adapter *i2c_adap,
+			      struct i2c_msg *msgs, int num)
+{
+	uint32_t  i, j, ret, data_size, data_chunk_size, next_eeprom_addr = 0;
+	uint8_t *data_ptr, data_chunk[MAX_SW_I2C_COMMANDS] = { 0 };
+
+	for (i = 0; i < num; i++) {
+		/*
+		 * SMU interface allows at most MAX_SW_I2C_COMMANDS bytes of data at
+		 * once and hence the data needs to be spliced into chunks and sent each
+		 * chunk separately
+		 */
+		data_size = msgs[i].len - 2;
+		data_chunk_size = MAX_SW_I2C_COMMANDS - 2;
+		next_eeprom_addr = (msgs[i].buf[0] << 8 & 0xff00) | (msgs[i].buf[1] & 0xff);
+		data_ptr = msgs[i].buf + 2;
+
+		for (j = 0; j < data_size / data_chunk_size; j++) {
+			/* Insert the EEPROM dest addess, bits 0-15 */
+			data_chunk[0] = ((next_eeprom_addr >> 8) & 0xff);
+			data_chunk[1] = (next_eeprom_addr & 0xff);
+
+			if (msgs[i].flags & I2C_M_RD) {
+				ret = arcturus_i2c_eeprom_read_data(i2c_adap,
+								(uint8_t)msgs[i].addr,
+								data_chunk, MAX_SW_I2C_COMMANDS);
+
+				memcpy(data_ptr, data_chunk + 2, data_chunk_size);
+			} else {
+
+				memcpy(data_chunk + 2, data_ptr, data_chunk_size);
+
+				ret = arcturus_i2c_eeprom_write_data(i2c_adap,
+								 (uint8_t)msgs[i].addr,
+								 data_chunk, MAX_SW_I2C_COMMANDS);
+			}
+
+			if (ret) {
+				num = -EIO;
+				goto fail;
+			}
+
+			next_eeprom_addr += data_chunk_size;
+			data_ptr += data_chunk_size;
+		}
+
+		if (data_size % data_chunk_size) {
+			data_chunk[0] = ((next_eeprom_addr >> 8) & 0xff);
+			data_chunk[1] = (next_eeprom_addr & 0xff);
+
+			if (msgs[i].flags & I2C_M_RD) {
+				ret = arcturus_i2c_eeprom_read_data(i2c_adap,
+								(uint8_t)msgs[i].addr,
+								data_chunk, (data_size % data_chunk_size) + 2);
+
+				memcpy(data_ptr, data_chunk + 2, data_size % data_chunk_size);
+			} else {
+				memcpy(data_chunk + 2, data_ptr, data_size % data_chunk_size);
+
+				ret = arcturus_i2c_eeprom_write_data(i2c_adap,
+								 (uint8_t)msgs[i].addr,
+								 data_chunk, (data_size % data_chunk_size) + 2);
+			}
+
+			if (ret) {
+				num = -EIO;
+				goto fail;
+			}
+		}
+	}
+
+fail:
+	return num;
+}
+
+static u32 arcturus_i2c_eeprom_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+
+static const struct i2c_algorithm arcturus_i2c_eeprom_i2c_algo = {
+	.master_xfer = arcturus_i2c_eeprom_i2c_xfer,
+	.functionality = arcturus_i2c_eeprom_i2c_func,
+};
+
+int arcturus_i2c_eeprom_control_init(struct i2c_adapter *control)
+{
+	struct amdgpu_device *adev = to_amdgpu_device(control);
+	int res;
+
+	control->owner = THIS_MODULE;
+	control->class = I2C_CLASS_SPD;
+	control->dev.parent = &adev->pdev->dev;
+	control->algo = &arcturus_i2c_eeprom_i2c_algo;
+	snprintf(control->name, sizeof(control->name), "RAS EEPROM");
+
+	res = i2c_add_adapter(control);
+	if (res)
+		DRM_ERROR("Failed to register hw i2c, err: %d\n", res);
+
+	return res;
+}
+
+void arcturus_i2c_eeprom_control_fini(struct i2c_adapter *control)
+{
+	i2c_del_adapter(control);
+}
+
 static const struct pptable_funcs arcturus_ppt_funcs = {
 	/* translate smu index into arcturus specific index */
 	.get_smu_msg_index = arcturus_get_smu_msg_index,
@@ -1964,6 +2191,8 @@ static const struct pptable_funcs arcturus_ppt_funcs = {
 	.get_power_limit = arcturus_get_power_limit,
 	.is_dpm_running = arcturus_is_dpm_running,
 	.dpm_set_uvd_enable = arcturus_dpm_set_uvd_enable,
+	.i2c_eeprom_init = arcturus_i2c_eeprom_control_init,
+	.i2c_eeprom_fini = arcturus_i2c_eeprom_control_fini,
 	.init_microcode = smu_v11_0_init_microcode,
 	.load_microcode = smu_v11_0_load_microcode,
 	.init_smc_tables = smu_v11_0_init_smc_tables,