Commit d6cfc1e2 authored by Benoit Parrot's avatar Benoit Parrot Committed by Benoit Cousson

ARM: dts: AM33XX: Add LCDC info into am335x-evm

Add LCDC device node in DT for am33xx
Add LCDC and Panel info in DT for am335x-evm

Changes:
- remove redundant/unnecessary SoC specific setting in the board dts
- resolved conflicts on for_3.13/dts
Signed-off-by: default avatarBenoit Parrot <bparrot@ti.com>
Signed-off-by: default avatarJoel Fernandes <joelf@ti.com>
Signed-off-by: default avatarBenoit Cousson <bcousson@baylibre.com>
parent 099f3a85
......@@ -85,6 +85,40 @@ backlight {
brightness-levels = <0 51 53 56 62 75 101 152 255>;
default-brightness-level = <8>;
};
panel {
compatible = "ti,tilcdc,panel";
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&lcd_pins_s0>;
panel-info {
ac-bias = <255>;
ac-bias-intrpt = <0>;
dma-burst-sz = <16>;
bpp = <32>;
fdd = <0x80>;
sync-edge = <0>;
sync-ctrl = <1>;
raster-order = <0>;
fifo-th = <0>;
};
display-timings {
800x480p62 {
clock-frequency = <30000000>;
hactive = <800>;
vactive = <480>;
hfront-porch = <39>;
hback-porch = <39>;
hsync-len = <47>;
vback-porch = <29>;
vfront-porch = <13>;
vsync-len = <2>;
hsync-active = <1>;
vsync-active = <1>;
};
};
};
};
&am33xx_pinmux {
......@@ -212,6 +246,39 @@ davinci_mdio_sleep: davinci_mdio_sleep {
0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
>;
};
lcd_pins_s0: lcd_pins_s0 {
pinctrl-single,pins = <
0x20 0x01 /* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
0x24 0x01 /* gpmc_ad9.lcd_data17, OUTPUT | MODE1 */
0x28 0x01 /* gpmc_ad10.lcd_data18, OUTPUT | MODE1 */
0x2c 0x01 /* gpmc_ad11.lcd_data19, OUTPUT | MODE1 */
0x30 0x01 /* gpmc_ad12.lcd_data20, OUTPUT | MODE1 */
0x34 0x01 /* gpmc_ad13.lcd_data21, OUTPUT | MODE1 */
0x38 0x01 /* gpmc_ad14.lcd_data22, OUTPUT | MODE1 */
0x3c 0x01 /* gpmc_ad15.lcd_data23, OUTPUT | MODE1 */
0xa0 0x00 /* lcd_data0.lcd_data0, OUTPUT | MODE0 */
0xa4 0x00 /* lcd_data1.lcd_data1, OUTPUT | MODE0 */
0xa8 0x00 /* lcd_data2.lcd_data2, OUTPUT | MODE0 */
0xac 0x00 /* lcd_data3.lcd_data3, OUTPUT | MODE0 */
0xb0 0x00 /* lcd_data4.lcd_data4, OUTPUT | MODE0 */
0xb4 0x00 /* lcd_data5.lcd_data5, OUTPUT | MODE0 */
0xb8 0x00 /* lcd_data6.lcd_data6, OUTPUT | MODE0 */
0xbc 0x00 /* lcd_data7.lcd_data7, OUTPUT | MODE0 */
0xc0 0x00 /* lcd_data8.lcd_data8, OUTPUT | MODE0 */
0xc4 0x00 /* lcd_data9.lcd_data9, OUTPUT | MODE0 */
0xc8 0x00 /* lcd_data10.lcd_data10, OUTPUT | MODE0 */
0xcc 0x00 /* lcd_data11.lcd_data11, OUTPUT | MODE0 */
0xd0 0x00 /* lcd_data12.lcd_data12, OUTPUT | MODE0 */
0xd4 0x00 /* lcd_data13.lcd_data13, OUTPUT | MODE0 */
0xd8 0x00 /* lcd_data14.lcd_data14, OUTPUT | MODE0 */
0xdc 0x00 /* lcd_data15.lcd_data15, OUTPUT | MODE0 */
0xe0 0x00 /* lcd_vsync.lcd_vsync, OUTPUT | MODE0 */
0xe4 0x00 /* lcd_hsync.lcd_hsync, OUTPUT | MODE0 */
0xe8 0x00 /* lcd_pclk.lcd_pclk, OUTPUT | MODE0 */
0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
>;
};
};
&uart0 {
......@@ -308,6 +375,10 @@ tmp275: tmp275@48 {
};
};
&lcdc {
status = "okay";
};
&elm {
status = "okay";
};
......
......@@ -684,6 +684,15 @@ elm: elm@48080000 {
status = "disabled";
};
lcdc: lcdc@4830e000 {
compatible = "ti,am33xx-tilcdc";
reg = <0x4830e000 0x1000>;
interrupt-parent = <&intc>;
interrupts = <36>;
ti,hwmods = "lcdc";
status = "disabled";
};
tscadc: tscadc@44e0d000 {
compatible = "ti,am3359-tscadc";
reg = <0x44e0d000 0x1000>;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment