ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102

BeagleBoard-X15 has capability for a fan and has an onboard TMP102
temperature sensor as well. This allows us to create a new thermal
zone (called, un-imaginatively "board"), and allows us to use some
active cooling as temperatures start edge upward in the system by
creating a new alert temperature (emperically 50C) for cpu.

NOTE: Fan is NOT mounted by default on the platform, in such a case,
all we end up doing is switch on a regulator and leak very minimal
current.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -87,6 +87,7 @@ gpio_fan: gpio_fan {
 		gpios =  <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>;
 		gpio-fan,speed-map = <0     0>,
 				     <13000 1>;
+		#cooling-cells = <2>;
 	};
 
 	extcon_usb1: extcon_usb1 {
@@ -442,6 +443,7 @@ tmp102: tmp102@48 {
 		pinctrl-0 = <&tmp102_pins_default>;
 		interrupt-parent = <&gpio7>;
 		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+		#thermal-sensor-cells = <1>;
 	};
 };
 
@@ -560,3 +562,50 @@ &omap_dwc3_2 {
 &usb2 {
 	dr_mode = "peripheral";
 };
+
+&cpu_trips {
+	cpu_alert1: cpu_alert1 {
+		temperature = <50000>; /* millicelsius */
+		hysteresis = <2000>; /* millicelsius */
+		type = "active";
+	};
+};
+
+&cpu_cooling_maps {
+	map1 {
+		trip = <&cpu_alert1>;
+		cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+	};
+};
+
+&thermal_zones {
+	board_thermal: board_thermal {
+		polling-delay-passive = <1250>; /* milliseconds */
+		polling-delay = <1500>; /* milliseconds */
+
+				/* sensor       ID */
+		thermal-sensors = <&tmp102     0>;
+
+		board_trips: trips {
+			board_alert0: board_alert {
+				temperature = <40000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "active";
+			};
+
+			board_crit: board_crit {
+				temperature = <105000>; /* millicelsius */
+				hysteresis = <0>; /* millicelsius */
+				type = "critical";
+			};
+		};
+
+		board_cooling_maps: cooling-maps {
+			map0 {
+				trip = <&board_alert0>;
+				cooling-device =
+				  <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+       };
+};

arch/arm/boot/dts/omap4-cpu-thermal.dtsi

@@ -18,7 +18,7 @@ cpu_thermal: cpu_thermal {
 			/* sensor       ID */
         thermal-sensors = <&bandgap     0>;
 
-        trips {
+	cpu_trips: trips {
                 cpu_alert0: cpu_alert {
                         temperature = <100000>; /* millicelsius */
                         hysteresis = <2000>; /* millicelsius */
@@ -31,7 +31,7 @@ cpu_crit: cpu_crit {
                 };
         };
 
-	cooling-maps {
+	cpu_cooling_maps: cooling-maps {
 		map0 {
 			trip = <&cpu_alert0>;
 			cooling-device =