Merge branches 'clk-imx', 'clk-ti', 'clk-xilinx', 'clk-nvidia', 'clk-qcom',...

Merge branches 'clk-imx', 'clk-ti', 'clk-xilinx', 'clk-nvidia', 'clk-qcom', 'clk-freescale' and 'clk-qoriq' into clk-next

 - Support for Xilinx Versal platform clks
 - Display clk controller on qcom sc7180
 - Video clk controller on qcom sc7180
 - Graphics clk controller on qcom sc7180
 - CPU PLLs for qcom msm8916
 - Fixes for clk controllers on qcom msm8998 SoCs
 - Move qcom msm8974 gfx3d clk to RPM control
 - Display port clk support on qcom sdm845 SoCs
 - Global clk controller on qcom ipq6018
 - Adjust composite clk to new way of describing clk parents
 - Add a driver for BCLK of Freescale SAI cores

* clk-imx: (32 commits)
  clk: imx: Add support for i.MX8MP clock driver
  dt-bindings: imx: Add clock binding doc for i.MX8MP
  clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
  clk: imx: imx8mq: Switch to clk_hw based API
  clk: imx: imx8mm: Switch to clk_hw based API
  clk: imx: imx8mn: Switch to clk_hw based API
  clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
  clk: imx: gate3: Switch to clk_hw based API
  clk: imx: add hw API imx_clk_hw_mux2_flags
  clk: imx: add imx_unregister_hw_clocks
  clk: imx: clk-composite-8m: Switch to clk_hw based API
  clk: imx: clk-pll14xx: Switch to clk_hw based API
  clk: imx7up: Rename the clks to hws
  clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
  clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
  clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
  clk: imx: Rename sccg and frac pll register to suggest clk_hw
  clk: imx: imx7ulp composite: Rename to show is clk_hw based
  clk: imx: pllv2: Switch to clk_hw based API
  clk: imx: pllv1: Switch to clk_hw based API
  ...

* clk-ti:
  clk: ti: clkctrl: Fix hidden dependency to node name
  clk: ti: add clkctrl data dra7 sgx
  clk: ti: omap5: Add missing AESS clock
  clk: ti: dra7: fix parent for gmac_clkctrl
  clk: ti: dra7: add vpe clkctrl data
  clk: ti: dra7: add cam clkctrl data
  dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock

* clk-xilinx:
  clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
  clk: zynqmp: Fix divider calculation
  clk: zynqmp: Add support for get max divider
  clk: zynqmp: Warn user if clock user are more than allowed
  clk: zynqmp: Extend driver for versal
  dt-bindings: clock: Add bindings for versal clock driver

* clk-nvidia:
  clk: tegra20/30: Explicitly set parent clock for Video Decoder
  clk: tegra20/30: Don't pre-initialize displays parent clock
  clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
  clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
  clk: tegra: Mark fuse clock as critical

* clk-qcom: (35 commits)
  clk: qcom: rpmh: Sort OF match table
  dt-bindings: fix warnings in validation of qcom,gcc.yaml
  dt-binding: fix compilation error of the example in qcom,gcc.yaml
  clk: qcom: Add ipq6018 Global Clock Controller support
  clk: qcom: Add DT bindings for ipq6018 gcc clock controller
  clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
  clk: qcom: rpmh: Add IPA clock for SC7180
  clk: qcom: rpmh: skip undefined clocks when registering
  clk: qcom: Add video clock controller driver for SC7180
  dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
  dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
  clk: qcom: Add graphics clock controller driver for SC7180
  dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
  dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
  clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
  clk: qcom: Add display clock controller driver for SC7180
  dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
  dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
  clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
  clk: qcom: alpha-pll: Remove useless read from set rate
  ...

* clk-freescale:
  clk: fsl-sai: new driver
  dt-bindings: clock: document the fsl-sai driver
  clk: composite: add _register_composite_pdata() variants

* clk-qoriq:
  clk: qoriq: add ls1088a hwaccel clocks support
  clk: ls1028a: Add clock driver for Display output interface
  dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings

Documentation/devicetree/bindings/clock/fsl,plldig.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/clock/fsl,plldig.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP QorIQ Layerscape LS1028A Display PIXEL Clock Binding
+
+maintainers:
+  - Wen He <wen.he_1@nxp.com>
+
+description: |
+  NXP LS1028A has a clock domain PXLCLK0 used for the Display output
+  interface in the display core, as implemented in TSMC CLN28HPM PLL.
+  which generate and offers pixel clocks to Display.
+
+properties:
+  compatible:
+    const: fsl,ls1028a-plldig
+
+  reg:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 0
+
+  fsl,vco-hz:
+     description: Optional for VCO frequency of the PLL in Hertz.
+        The VCO frequency of this PLL cannot be changed during runtime
+        only at startup. Therefore, the output frequencies are very
+        limited and might not even closely match the requested frequency.
+        To work around this restriction the user may specify its own
+        desired VCO frequency for the PLL.
+     minimum: 650000000
+     maximum: 1300000000
+     default: 1188000000
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - '#clock-cells'
+
+examples:
+  # Display PIXEL Clock node:
+  - |
+    dpclk: clock-display@f1f0000 {
+        compatible = "fsl,ls1028a-plldig";
+        reg = <0x0 0xf1f0000 0x0 0xffff>;
+        #clock-cells = <0>;
+        clocks = <&osc_27m>;
+    };
+
+...

Documentation/devicetree/bindings/clock/fsl,sai-clock.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/clock/fsl,sai-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale SAI bitclock-as-a-clock binding
+
+maintainers:
+  - Michael Walle <michael@walle.cc>
+
+description: |
+  It is possible to use the BCLK pin of a SAI module as a generic clock
+  output. Some SoC are very constrained in their pin multiplexer
+  configuration. Eg. pins can only be changed groups. For example, on the
+  LS1028A SoC you can only enable SAIs in pairs. If you use only one SAI,
+  the second pins are wasted. Using this binding it is possible to use the
+  clock of the second SAI as a MCLK clock for an audio codec, for example.
+
+  This is a composite of a gated clock and a divider clock.
+
+properties:
+  compatible:
+    const: fsl,vf610-sai-clock
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  '#clock-cells':
+    const: 0
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        mclk: clock-mclk@f130080 {
+            compatible = "fsl,vf610-sai-clock";
+            reg = <0x0 0xf130080 0x0 0x80>;
+            #clock-cells = <0>;
+            clocks = <&parentclk>;
+        };
+    };

Documentation/devicetree/bindings/clock/imx8mp-clock.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/clock/imx8mp-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8M Plus Clock Control Module Binding
+
+maintainers:
+  - Anson Huang <Anson.Huang@nxp.com>
+
+description:
+  NXP i.MX8M Plus clock control module is an integrated clock controller, which
+  generates and supplies to all modules.
+
+properties:
+  compatible:
+    const: fsl,imx8mp-ccm
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: 32k osc
+      - description: 24m osc
+      - description: ext1 clock input
+      - description: ext2 clock input
+      - description: ext3 clock input
+      - description: ext4 clock input
+
+  clock-names:
+    items:
+      - const: osc_32k
+      - const: osc_24m
+      - const: clk_ext1
+      - const: clk_ext2
+      - const: clk_ext3
+      - const: clk_ext4
+
+  '#clock-cells':
+    const: 1
+    description:
+      The clock consumer should specify the desired clock by having the clock
+      ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx8mp-clock.h
+      for the full list of i.MX8M Plus clock IDs.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - '#clock-cells'
+
+examples:
+  # Clock Control Module node:
+  - |
+    clk: clock-controller@30380000 {
+        compatible = "fsl,imx8mp-ccm";
+        reg = <0x30380000 0x10000>;
+        #clock-cells = <1>;
+        clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>,
+                 <&clk_ext2>, <&clk_ext3>, <&clk_ext4>;
+        clock-names = "osc_32k", "osc_24m", "clk_ext1",
+                      "clk_ext2", "clk_ext3", "clk_ext4";
+    };
+
+...

Documentation/devicetree/bindings/clock/qcom,dispcc.txt

-Qualcomm Technologies, Inc. Display Clock Controller Binding
-------------------------------------------------------------
-
-Required properties :
-
-- compatible : shall contain "qcom,sdm845-dispcc"
-- reg : shall contain base register location and length.
-- #clock-cells : from common clock binding, shall contain 1.
-- #reset-cells : from common reset binding, shall contain 1.
-- #power-domain-cells : from generic power domain binding, shall contain 1.
-
-Example:
-	dispcc: clock-controller@af00000 {
-		compatible = "qcom,sdm845-dispcc";
-		reg = <0xaf00000 0x100000>;
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-		#power-domain-cells = <1>;
-	};

Documentation/devicetree/bindings/clock/qcom,dispcc.yaml

+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/clock/qcom,dispcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Display Clock & Reset Controller Binding
+
+maintainers:
+  - Taniya Das <tdas@codeaurora.org>
+
+description: |
+  Qualcomm display clock control module which supports the clocks, resets and
+  power domains.
+
+properties:
+  compatible:
+    enum:
+      - qcom,sc7180-dispcc
+      - qcom,sdm845-dispcc
+
+  clocks:
+    minItems: 1
+    maxItems: 2
+    items:
+      - description: Board XO source
+      - description: GPLL0 source from GCC
+
+  clock-names:
+    items:
+      - const: xo
+      - const: gpll0
+
+  '#clock-cells':
+    const: 1
+
+  '#reset-cells':
+    const: 1
+
+  '#power-domain-cells':
+    const: 1
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - '#clock-cells'
+  - '#reset-cells'
+  - '#power-domain-cells'
+
+examples:
+  # Example of DISPCC with clock node properties for SDM845:
+  - |
+    clock-controller@af00000 {
+      compatible = "qcom,sdm845-dispcc";
+      reg = <0xaf00000 0x10000>;
+      clocks = <&rpmhcc 0>, <&gcc 24>;
+      clock-names = "xo", "gpll0";
+      #clock-cells = <1>;
+      #reset-cells = <1>;
+      #power-domain-cells = <1>;
+     };
+...

Documentation/devicetree/bindings/clock/qcom,gcc.yaml

@@ -19,8 +19,9 @@ properties:
     enum:
        - qcom,gcc-apq8064
        - qcom,gcc-apq8084
-       - qcom,gcc-ipq8064
        - qcom,gcc-ipq4019
+       - qcom,gcc-ipq6018
+       - qcom,gcc-ipq8064
        - qcom,gcc-ipq8074
        - qcom,gcc-msm8660
        - qcom,gcc-msm8916
@@ -40,20 +41,50 @@ properties:
        - qcom,gcc-sm8150
 
   clocks:
-    minItems: 1
-    maxItems: 3
-    items:
+    oneOf:
+      #qcom,gcc-sm8150
+      #qcom,gcc-sc7180
+      - items:
         - description: Board XO source
         - description: Board active XO source
         - description: Sleep clock source
+      #qcom,gcc-msm8996
+      - items:
+        - description: XO source
+        - description: Second XO source
+        - description: Sleep clock source
+      #qcom,gcc-msm8998
+      - items:
+        - description: Board XO source
+        - description: Sleep clock source
+        - description: USB 3.0 phy pipe clock
+        - description: UFS phy rx symbol clock for pipe 0
+        - description: UFS phy rx symbol clock for pipe 1
+        - description: UFS phy tx symbol clock
+        - description: PCIE phy pipe clock
 
   clock-names:
-    minItems: 1
-    maxItems: 3
-    items:
+    oneOf:
+      #qcom,gcc-sm8150
+      #qcom,gcc-sc7180
+      - items:
         - const: bi_tcxo
         - const: bi_tcxo_ao
         - const: sleep_clk
+      #qcom,gcc-msm8996
+      - items:
+        - const: cxo
+        - const: cxo2
+        - const: sleep_clk
+      #qcom,gcc-msm8998
+      - items:
+        - const: xo
+        - const: sleep_clk
+        - const: usb3_pipe
+        - const: ufs_rx_symbol0
+        - const: ufs_rx_symbol1
+        - const: ufs_tx_symbol0
+        - const: pcie0_pipe
 
   '#clock-cells':
     const: 1
@@ -118,6 +149,7 @@ else:
       compatible:
         contains:
           enum:
+            - qcom,gcc-msm8998
             - qcom,gcc-sm8150
             - qcom,gcc-sc7180
   then:
@@ -179,10 +211,35 @@ examples:
     clock-controller@100000 {
       compatible = "qcom,gcc-sc7180";
       reg = <0x100000 0x1f0000>;
-      clocks = <&rpmhcc 0>, <&rpmhcc 1>;
-      clock-names = "bi_tcxo", "bi_tcxo_ao";
+      clocks = <&rpmhcc 0>, <&rpmhcc 1>, <0>;
+      clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk";
+      #clock-cells = <1>;
+      #reset-cells = <1>;
+      #power-domain-cells = <1>;
+    };
+
+  # Example of MSM8998 GCC:
+  - |
+    #include <dt-bindings/clock/qcom,rpmcc.h>
+    clock-controller@100000 {
+      compatible = "qcom,gcc-msm8998";
       #clock-cells = <1>;
       #reset-cells = <1>;
       #power-domain-cells = <1>;
+      reg = <0x00100000 0xb0000>;
+      clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+               <&sleep>,
+               <0>,
+               <0>,
+               <0>,
+               <0>,
+               <0>;
+      clock-names = "xo",
+                    "sleep_clk",
+                    "usb3_pipe",
+                    "ufs_rx_symbol0",
+                    "ufs_rx_symbol1",
+                    "ufs_tx_symbol0",
+                    "pcie0_pipe";
     };
 ...

Documentation/devicetree/bindings/clock/qcom,gpucc.txt

-Qualcomm Graphics Clock & Reset Controller Binding
---------------------------------------------------
-
-Required properties :
-- compatible : shall contain "qcom,sdm845-gpucc" or "qcom,msm8998-gpucc"
-- reg : shall contain base register location and length
-- #clock-cells : from common clock binding, shall contain 1
-- #reset-cells : from common reset binding, shall contain 1
-- #power-domain-cells : from generic power domain binding, shall contain 1
-- clocks : shall contain the XO clock
-	   shall contain the gpll0 out main clock (msm8998)
-- clock-names : shall be "xo"
-		shall be "gpll0" (msm8998)
-
-Example:
-	gpucc: clock-controller@5090000 {
-		compatible = "qcom,sdm845-gpucc";
-		reg = <0x5090000 0x9000>;
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-		#power-domain-cells = <1>;
-		clocks = <&rpmhcc RPMH_CXO_CLK>;
-		clock-names = "xo";
-	};

Documentation/devicetree/bindings/clock/qcom,gpucc.yaml

+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/clock/qcom,gpucc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Graphics Clock & Reset Controller Binding
+
+maintainers:
+  - Taniya Das <tdas@codeaurora.org>
+
+description: |
+  Qualcomm grpahics clock control module which supports the clocks, resets and
+  power domains.
+
+properties:
+  compatible:
+    enum:
+      - qcom,msm8998-gpucc
+      - qcom,sc7180-gpucc
+      - qcom,sdm845-gpucc
+
+  clocks:
+    minItems: 1
+    maxItems: 3
+    items:
+      - description: Board XO source
+      - description: GPLL0 main branch source from GCC(gcc_gpu_gpll0_clk_src)
+      - description: GPLL0 div branch source from GCC(gcc_gpu_gpll0_div_clk_src)
+
+  clock-names:
+    minItems: 1
+    maxItems: 3
+    items:
+      - const: xo
+      - const: gpll0_main
+      - const: gpll0_div
+
+  '#clock-cells':
+    const: 1
+
+  '#reset-cells':
+    const: 1
+
+  '#power-domain-cells':
+    const: 1
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - '#clock-cells'
+  - '#reset-cells'
+  - '#power-domain-cells'
+
+examples:
+  # Example of GPUCC with clock node properties for SDM845:
+  - |
+    clock-controller@5090000 {
+      compatible = "qcom,sdm845-gpucc";
+      reg = <0x5090000 0x9000>;
+      clocks = <&rpmhcc 0>, <&gcc 31>, <&gcc 32>;
+      clock-names = "xo", "gpll0_main", "gpll0_div";
+      #clock-cells = <1>;
+      #reset-cells = <1>;
+      #power-domain-cells = <1>;
+     };
+...

Documentation/devicetree/bindings/clock/qcom,mmcc.txt

-Qualcomm Multimedia Clock & Reset Controller Binding
-----------------------------------------------------
-
-Required properties :
-- compatible : shall contain only one of the following:
-
-			"qcom,mmcc-apq8064"
-			"qcom,mmcc-apq8084"
-			"qcom,mmcc-msm8660"
-			"qcom,mmcc-msm8960"
-			"qcom,mmcc-msm8974"
-			"qcom,mmcc-msm8996"
-
-- reg : shall contain base register location and length
-- #clock-cells : shall contain 1
-- #reset-cells : shall contain 1
-
-Optional properties :
-- #power-domain-cells : shall contain 1
-
-Example:
-	clock-controller@4000000 {
-		compatible = "qcom,mmcc-msm8960";
-		reg = <0x4000000 0x1000>;
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-		#power-domain-cells = <1>;
-	};

Documentation/devicetree/bindings/clock/qcom,mmcc.yaml

+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/clock/qcom,mmcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Multimedia Clock & Reset Controller Binding
+
+maintainers:
+  - Jeffrey Hugo <jhugo@codeaurora.org>
+  - Taniya Das <tdas@codeaurora.org>
+
+description: |
+  Qualcomm multimedia clock control module which supports the clocks, resets and
+  power domains.
+
+properties:
+  compatible :
+    enum:
+       - qcom,mmcc-apq8064
+       - qcom,mmcc-apq8084
+       - qcom,mmcc-msm8660
+       - qcom,mmcc-msm8960
+       - qcom,mmcc-msm8974
+       - qcom,mmcc-msm8996
+       - qcom,mmcc-msm8998
+
+  clocks:
+    items:
+      - description: Board XO source
+      - description: Board sleep source
+      - description: Global PLL 0 clock
+      - description: DSI phy instance 0 dsi clock
+      - description: DSI phy instance 0 byte clock
+      - description: DSI phy instance 1 dsi clock
+      - description: DSI phy instance 1 byte clock
+      - description: HDMI phy PLL clock
+      - description: DisplayPort phy PLL vco clock
+      - description: DisplayPort phy PLL link clock
+
+  clock-names:
+    items:
+      - const: xo
+      - const: sleep
+      - const: gpll0
+      - const: dsi0dsi
+      - const: dsi0byte
+      - const: dsi1dsi
+      - const: dsi1byte
+      - const: hdmipll
+      - const: dpvco
+      - const: dplink
+
+  '#clock-cells':
+    const: 1
+
+  '#reset-cells':
+    const: 1
+
+  '#power-domain-cells':
+    const: 1
+
+  reg:
+    maxItems: 1
+
+  protected-clocks:
+    description:
+       Protected clock specifier list as per common clock binding
+
+required:
+  - compatible
+  - reg
+  - '#clock-cells'
+  - '#reset-cells'
+  - '#power-domain-cells'
+
+if:
+  properties:
+    compatible:
+      contains:
+        const: qcom,mmcc-msm8998
+
+then:
+  required:
+    - clocks
+    - clock-names
+
+examples:
+  # Example for MMCC for MSM8960:
+  - |
+    clock-controller@4000000 {
+      compatible = "qcom,mmcc-msm8960";
+      reg = <0x4000000 0x1000>;
+      #clock-cells = <1>;
+      #reset-cells = <1>;
+      #power-domain-cells = <1>;
+    };
+...

Documentation/devicetree/bindings/clock/qcom,videocc.txt

-Qualcomm Video Clock & Reset Controller Binding
------------------------------------------------
-
-Required properties :
-- compatible : shall contain "qcom,sdm845-videocc"
-- reg : shall contain base register location and length
-- #clock-cells : from common clock binding, shall contain 1.
-- #power-domain-cells : from generic power domain binding, shall contain 1.
-- #reset-cells : from common reset binding, shall contain 1.
-
-Example:
-	videocc: clock-controller@ab00000 {
-		compatible = "qcom,sdm845-videocc";
-		reg = <0xab00000 0x10000>;
-		#clock-cells = <1>;
-		#power-domain-cells = <1>;
-		#reset-cells = <1>;
-	};

Documentation/devicetree/bindings/clock/qcom,videocc.yaml

+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/clock/qcom,videocc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Video Clock & Reset Controller Binding
+
+maintainers:
+  - Taniya Das <tdas@codeaurora.org>
+
+description: |
+  Qualcomm video clock control module which supports the clocks, resets and
+  power domains.
+
+properties:
+  compatible:
+    enum:
+      - qcom,sc7180-videocc
+      - qcom,sdm845-videocc
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: xo
+
+  '#clock-cells':
+    const: 1
+
+  '#reset-cells':
+    const: 1
+
+  '#power-domain-cells':
+    const: 1
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - '#clock-cells'
+  - '#reset-cells'
+  - '#power-domain-cells'
+
+examples:
+  # Example of VIDEOCC with clock node properties for SDM845:
+  - |
+    clock-controller@ab00000 {
+      compatible = "qcom,sdm845-videocc";
+      reg = <0xab00000 0x10000>;
+      clocks = <&rpmhcc 0>;
+      clock-names = "xo";
+      #clock-cells = <1>;
+      #reset-cells = <1>;
+      #power-domain-cells = <1>;
+     };
+...

Documentation/devicetree/bindings/clock/ti-clkctrl.txt

@@ -16,18 +16,23 @@ For more information, please see the Linux clock framework binding at
 Documentation/devicetree/bindings/clock/clock-bindings.txt.
 
 Required properties :
-- compatible : shall be "ti,clkctrl"
+- compatible : shall be "ti,clkctrl" or a clock domain specific name:
+	       "ti,clkctrl-l4-cfg"
+	       "ti,clkctrl-l4-per"
+	       "ti,clkctrl-l4-secure"
+	       "ti,clkctrl-l4-wkup"
 - #clock-cells : shall contain 2 with the first entry being the instance
 		 offset from the clock domain base and the second being the
 		 clock index
+- reg : clock registers
 
 Example: Clock controller node on omap 4430:
 
 &cm2 {
 	l4per: cm@1400 {
 		cm_l4per@0 {
-			cm_l4per_clkctrl: clk@20 {
-				compatible = "ti,clkctrl";
+			cm_l4per_clkctrl: clock@20 {
+				compatible = "ti,clkctrl-l4-per", "ti,clkctrl";
 				reg = <0x20 0x1b0>;
 				#clock-cells = <2>;
 			};

Documentation/devicetree/bindings/clock/ti/dra7-atl.txt

@@ -43,7 +43,7 @@ Configuration of ATL instances:
 	- aws : Audio word select signal selection
 };
 
-For valid word select signals, see the dt-bindings/clk/ti-dra7-atl.h include
+For valid word select signals, see the dt-bindings/clock/ti-dra7-atl.h include
 file.
 
 Examples:
@@ -83,7 +83,7 @@ atl: atl@4843c000 {
 	clock-names = "fck";
 };
 
-#include <dt-bindings/clk/ti-dra7-atl.h>
+#include <dt-bindings/clock/ti-dra7-atl.h>
 
 &atl {
 

Documentation/devicetree/bindings/clock/xlnx,versal-clk.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/clock/xlnx,versal-clk.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Versal clock controller
+
+maintainers:
+  - Michal Simek <michal.simek@xilinx.com>
+  - Jolly Shah <jolly.shah@xilinx.com>
+  - Rajan Vaja <rajan.vaja@xilinx.com>
+
+description: |
+  The clock controller is a hardware block of Xilinx versal clock tree. It
+  reads required input clock frequencies from the devicetree and acts as clock
+  provider for all clock consumers of PS clocks.
+
+select: false
+
+properties:
+  compatible:
+    const: xlnx,versal-clk
+
+  "#clock-cells":
+    const: 1
+
+  clocks:
+    description: List of clock specifiers which are external input
+      clocks to the given clock controller.
+    items:
+      - description: reference clock
+      - description: alternate reference clock
+      - description: alternate reference clock for programmable logic
+
+  clock-names:
+    items:
+      - const: ref
+      - const: alt_ref
+      - const: pl_alt_ref
+
+required:
+  - compatible
+  - "#clock-cells"
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    firmware {
+      zynqmp_firmware: zynqmp-firmware {
+        compatible = "xlnx,zynqmp-firmware";
+        method = "smc";
+        versal_clk: clock-controller {
+          #clock-cells = <1>;
+          compatible = "xlnx,versal-clk";
+          clocks = <&ref>, <&alt_ref>, <&pl_alt_ref>;
+          clock-names = "ref", "alt_ref", "pl_alt_ref";
+        };
+      };
+    };
+...

Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt

@@ -21,10 +21,11 @@ platforms.
 	Usage: required
 	Value type: <prop-encoded-array>
 	Definition: must specify the base address and size of the global block
+
 - clocks:
-	Usage: required if #clocks-cells property is present
-	Value type: <phandle>
-	Definition: phandle to the input PLL, which feeds the APCS mux/divider
+	Usage: required if #clock-names property is present
+	Value type: <phandle array>
+	Definition: phandles to the two parent clocks of the clock driver.
 
 - #mbox-cells:
 	Usage: required
@@ -36,6 +37,12 @@ platforms.
 	Value type: <u32>
 	Definition: as described in clock.txt, must be 0
 
+- clock-names:
+	Usage: required if the platform data based clock driver needs to
+	retrieve the parent clock names from device tree.
+	This will requires two mandatory clocks to be defined.
+	Value type: <string-array>
+	Definition: must be "pll" and "aux"
 
 = EXAMPLE
 The following example describes the APCS HMSS found in MSM8996 and part of the
@@ -68,3 +75,14 @@ Below is another example of the APCS binding on MSM8916 platforms:
 		clocks = <&a53pll>;
 		#clock-cells = <0>;
 	};
+
+Below is another example of the APCS binding on QCS404 platforms:
+
+	apcs_glb: mailbox@b011000 {
+		compatible = "qcom,qcs404-apcs-apps-global", "syscon";
+		reg = <0x0b011000 0x1000>;
+		#mbox-cells = <1>;
+		clocks = <&apcs_hfpll>, <&gcc GCC_GPLL0_AO_OUT_MAIN>;
+		clock-names = "pll", "aux";
+		#clock-cells = <0>;
+	};

arch/arm/boot/dts/dra7-evm-common.dtsi

@@ -4,7 +4,7 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/ti-dra7-atl.h>
+#include <dt-bindings/clock/ti-dra7-atl.h>
 #include <dt-bindings/input/input.h>
 
 / {

arch/arm/boot/dts/dra72-evm-common.dtsi

@@ -6,7 +6,7 @@
 
 #include "dra72x.dtsi"
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/ti-dra7-atl.h>
+#include <dt-bindings/clock/ti-dra7-atl.h>
 
 / {
 	compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";

arch/arm/boot/dts/dra7xx-clocks.dtsi

@@ -1734,6 +1734,20 @@ dss_clkctrl: dss-clkctrl@20 {
 		};
 	};
 
+	gpu_cm: gpu-cm@1200 {
+		compatible = "ti,omap4-cm";
+		reg = <0x1200 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x1200 0x100>;
+
+		gpu_clkctrl: gpu-clkctrl@20 {
+			compatible = "ti,clkctrl";
+			reg = <0x20 0x4>;
+			#clock-cells = <2>;
+		};
+	};
+
 	l3init_cm: l3init-cm@1300 {
 		compatible = "ti,omap4-cm";
 		reg = <0x1300 0x100>;

drivers/clk/Kconfig

@@ -174,6 +174,18 @@ config COMMON_CLK_CS2000_CP
 	help
 	  If you say yes here you get support for the CS2000 clock multiplier.
 
+config COMMON_CLK_FSL_SAI
+	bool "Clock driver for BCLK of Freescale SAI cores"
+	depends on ARCH_LAYERSCAPE || COMPILE_TEST
+	help
+	  This driver supports the Freescale SAI (Synchronous Audio Interface)
+	  to be used as a generic clock output. Some SoCs have restrictions
+	  regarding the possible pin multiplexer settings. Eg. on some SoCs
+	  two SAI interfaces can only be enabled together. If just one is
+	  needed, the BCLK pin of the second one can be used as general
+	  purpose clock output. Ideally, it can be used to drive an audio
+	  codec (sometimes known as MCLK).
+
 config COMMON_CLK_GEMINI
 	bool "Clock driver for Cortina Systems Gemini SoC"
 	depends on ARCH_GEMINI || COMPILE_TEST
@@ -225,6 +237,16 @@ config CLK_QORIQ
 	  This adds the clock driver support for Freescale QorIQ platforms
 	  using common clock framework.
 
+config CLK_LS1028A_PLLDIG
+        tristate "Clock driver for LS1028A Display output"
+        depends on ARCH_LAYERSCAPE || COMPILE_TEST
+        default ARCH_LAYERSCAPE
+        help
+          This driver support the Display output interfaces(LCD, DPHY) pixel clocks
+          of the QorIQ Layerscape LS1028A, as implemented TSMC CLN28HPM PLL. Not all
+          features of the PLL are currently supported by the driver. By default,
+          configured bypass mode with this PLL.
+
 config COMMON_CLK_XGENE
 	bool "Clock driver for APM XGene SoC"
 	default ARCH_XGENE

drivers/clk/Makefile

@@ -29,6 +29,7 @@ obj-$(CONFIG_ARCH_CLPS711X)		+= clk-clps711x.o
 obj-$(CONFIG_COMMON_CLK_CS2000_CP)	+= clk-cs2000-cp.o
 obj-$(CONFIG_ARCH_EFM32)		+= clk-efm32gg.o
 obj-$(CONFIG_COMMON_CLK_FIXED_MMIO)	+= clk-fixed-mmio.o
+obj-$(CONFIG_COMMON_CLK_FSL_SAI)	+= clk-fsl-sai.o
 obj-$(CONFIG_COMMON_CLK_GEMINI)		+= clk-gemini.o
 obj-$(CONFIG_COMMON_CLK_ASPEED)		+= clk-aspeed.o
 obj-$(CONFIG_MACH_ASPEED_G6)		+= clk-ast2600.o
@@ -44,6 +45,7 @@ obj-$(CONFIG_ARCH_NPCM7XX)	    	+= clk-npcm7xx.o
 obj-$(CONFIG_ARCH_NSPIRE)		+= clk-nspire.o
 obj-$(CONFIG_COMMON_CLK_OXNAS)		+= clk-oxnas.o
 obj-$(CONFIG_COMMON_CLK_PALMAS)		+= clk-palmas.o
+obj-$(CONFIG_CLK_LS1028A_PLLDIG)	+= clk-plldig.o
 obj-$(CONFIG_COMMON_CLK_PWM)		+= clk-pwm.o
 obj-$(CONFIG_CLK_QORIQ)			+= clk-qoriq.o
 obj-$(CONFIG_COMMON_CLK_RK808)		+= clk-rk808.o

drivers/clk/clk-composite.c

@@ -199,8 +199,9 @@ static void clk_composite_disable(struct clk_hw *hw)
 	gate_ops->disable(gate_hw);
 }
 
-struct clk_hw *clk_hw_register_composite(struct device *dev, const char *name,
-			const char * const *parent_names, int num_parents,
+static struct clk_hw *__clk_hw_register_composite(struct device *dev,
+			const char *name, const char * const *parent_names,
+			const struct clk_parent_data *pdata, int num_parents,
 			struct clk_hw *mux_hw, const struct clk_ops *mux_ops,
 			struct clk_hw *rate_hw, const struct clk_ops *rate_ops,
 			struct clk_hw *gate_hw, const struct clk_ops *gate_ops,
@@ -218,7 +219,10 @@ struct clk_hw *clk_hw_register_composite(struct device *dev, const char *name,
 
 	init.name = name;
 	init.flags = flags;
+	if (parent_names)
 		init.parent_names = parent_names;
+	else
+		init.parent_data = pdata;
 	init.num_parents = num_parents;
 	hw = &composite->hw;
 
@@ -312,6 +316,34 @@ struct clk_hw *clk_hw_register_composite(struct device *dev, const char *name,
 	return hw;
 }
 
+struct clk_hw *clk_hw_register_composite(struct device *dev, const char *name,
+			const char * const *parent_names, int num_parents,
+			struct clk_hw *mux_hw, const struct clk_ops *mux_ops,
+			struct clk_hw *rate_hw, const struct clk_ops *rate_ops,
+			struct clk_hw *gate_hw, const struct clk_ops *gate_ops,
+			unsigned long flags)
+{
+	return __clk_hw_register_composite(dev, name, parent_names, NULL,
+					   num_parents, mux_hw, mux_ops,
+					   rate_hw, rate_ops, gate_hw,
+					   gate_ops, flags);
+}
+
+struct clk_hw *clk_hw_register_composite_pdata(struct device *dev,
+			const char *name,
+			const struct clk_parent_data *parent_data,
+			int num_parents,
+			struct clk_hw *mux_hw, const struct clk_ops *mux_ops,
+			struct clk_hw *rate_hw, const struct clk_ops *rate_ops,
+			struct clk_hw *gate_hw, const struct clk_ops *gate_ops,
+			unsigned long flags)
+{
+	return __clk_hw_register_composite(dev, name, NULL, parent_data,
+					   num_parents, mux_hw, mux_ops,
+					   rate_hw, rate_ops, gate_hw,
+					   gate_ops, flags);
+}
+
 struct clk *clk_register_composite(struct device *dev, const char *name,
 			const char * const *parent_names, int num_parents,
 			struct clk_hw *mux_hw, const struct clk_ops *mux_ops,
@@ -329,6 +361,24 @@ struct clk *clk_register_composite(struct device *dev, const char *name,
 	return hw->clk;
 }
 
+struct clk *clk_register_composite_pdata(struct device *dev, const char *name,
+			const struct clk_parent_data *parent_data,
+			int num_parents,
+			struct clk_hw *mux_hw, const struct clk_ops *mux_ops,
+			struct clk_hw *rate_hw, const struct clk_ops *rate_ops,
+			struct clk_hw *gate_hw, const struct clk_ops *gate_ops,
+			unsigned long flags)
+{
+	struct clk_hw *hw;
+
+	hw = clk_hw_register_composite_pdata(dev, name, parent_data,
+			num_parents, mux_hw, mux_ops, rate_hw, rate_ops,
+			gate_hw, gate_ops, flags);
+	if (IS_ERR(hw))
+		return ERR_CAST(hw);
+	return hw->clk;
+}
+
 void clk_unregister_composite(struct clk *clk)
 {
 	struct clk_composite *composite;

drivers/clk/clk-fsl-sai.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Freescale SAI BCLK as a generic clock driver
+ *
+ * Copyright 2020 Michael Walle <michael@walle.cc>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+
+#define I2S_CSR		0x00
+#define I2S_CR2		0x08
+#define CSR_BCE_BIT	28
+#define CR2_BCD		BIT(24)
+#define CR2_DIV_SHIFT	0
+#define CR2_DIV_WIDTH	8
+
+struct fsl_sai_clk {
+	struct clk_divider div;
+	struct clk_gate gate;
+	spinlock_t lock;
+};
+
+static int fsl_sai_clk_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct fsl_sai_clk *sai_clk;
+	struct clk_parent_data pdata = { .index = 0 };
+	void __iomem *base;
+	struct clk_hw *hw;
+	struct resource *res;
+
+	sai_clk = devm_kzalloc(dev, sizeof(*sai_clk), GFP_KERNEL);
+	if (!sai_clk)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	spin_lock_init(&sai_clk->lock);
+
+	sai_clk->gate.reg = base + I2S_CSR;
+	sai_clk->gate.bit_idx = CSR_BCE_BIT;
+	sai_clk->gate.lock = &sai_clk->lock;
+
+	sai_clk->div.reg = base + I2S_CR2;
+	sai_clk->div.shift = CR2_DIV_SHIFT;
+	sai_clk->div.width = CR2_DIV_WIDTH;
+	sai_clk->div.lock = &sai_clk->lock;
+
+	/* set clock direction, we are the BCLK master */
+	writel(CR2_BCD, base + I2S_CR2);
+
+	hw = clk_hw_register_composite_pdata(dev, dev->of_node->name,
+					     &pdata, 1, NULL, NULL,
+					     &sai_clk->div.hw,
+					     &clk_divider_ops,
+					     &sai_clk->gate.hw,
+					     &clk_gate_ops,
+					     CLK_SET_RATE_GATE);
+	if (IS_ERR(hw))
+		return PTR_ERR(hw);
+
+	return devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get, hw);
+}
+
+static const struct of_device_id of_fsl_sai_clk_ids[] = {
+	{ .compatible = "fsl,vf610-sai-clock" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, of_fsl_sai_clk_ids);
+
+static struct platform_driver fsl_sai_clk_driver = {
+	.probe = fsl_sai_clk_probe,
+	.driver		= {
+		.name	= "fsl-sai-clk",
+		.of_match_table = of_fsl_sai_clk_ids,
+	},
+};
+module_platform_driver(fsl_sai_clk_driver);
+
+MODULE_DESCRIPTION("Freescale SAI bitclock-as-a-clock driver");
+MODULE_AUTHOR("Michael Walle <michael@walle.cc>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:fsl-sai-clk");

drivers/clk/clk-plldig.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 NXP
+ *
+ * Clock driver for LS1028A Display output interfaces(LCD, DPHY).
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/bitfield.h>
+
+/* PLLDIG register offsets and bit masks */
+#define PLLDIG_REG_PLLSR            0x24
+#define PLLDIG_LOCK_MASK            BIT(2)
+#define PLLDIG_REG_PLLDV            0x28
+#define PLLDIG_MFD_MASK             GENMASK(7, 0)
+#define PLLDIG_RFDPHI1_MASK         GENMASK(30, 25)
+#define PLLDIG_REG_PLLFM            0x2c
+#define PLLDIG_SSCGBYP_ENABLE       BIT(30)
+#define PLLDIG_REG_PLLFD            0x30
+#define PLLDIG_FDEN                 BIT(30)
+#define PLLDIG_FRAC_MASK            GENMASK(15, 0)
+#define PLLDIG_REG_PLLCAL1          0x38
+#define PLLDIG_REG_PLLCAL2          0x3c
+
+/* Range of the VCO frequencies, in Hz */
+#define PLLDIG_MIN_VCO_FREQ         650000000
+#define PLLDIG_MAX_VCO_FREQ         1300000000
+
+/* Range of the output frequencies, in Hz */
+#define PHI1_MIN_FREQ               27000000
+#define PHI1_MAX_FREQ               600000000
+
+/* Maximum value of the reduced frequency divider */
+#define MAX_RFDPHI1          63UL
+
+/* Best value of multiplication factor divider */
+#define PLLDIG_DEFAULT_MFD   44
+
+/*
+ * Denominator part of the fractional part of the
+ * loop multiplication factor.
+ */
+#define MFDEN          20480
+
+static const struct clk_parent_data parent_data[] = {
+	{ .index = 0 },
+};
+
+struct clk_plldig {
+	struct clk_hw hw;
+	void __iomem *regs;
+	unsigned int vco_freq;
+};
+
+#define to_clk_plldig(_hw)	container_of(_hw, struct clk_plldig, hw)
+
+static int plldig_enable(struct clk_hw *hw)
+{
+	struct clk_plldig *data = to_clk_plldig(hw);
+	u32 val;
+
+	val = readl(data->regs + PLLDIG_REG_PLLFM);
+	/*
+	 * Use Bypass mode with PLL off by default, the frequency overshoot
+	 * detector output was disable. SSCG Bypass mode should be enable.
+	 */
+	val |= PLLDIG_SSCGBYP_ENABLE;
+	writel(val, data->regs + PLLDIG_REG_PLLFM);
+
+	return 0;
+}
+
+static void plldig_disable(struct clk_hw *hw)
+{
+	struct clk_plldig *data = to_clk_plldig(hw);
+	u32 val;
+
+	val = readl(data->regs + PLLDIG_REG_PLLFM);
+
+	val &= ~PLLDIG_SSCGBYP_ENABLE;
+	val |= FIELD_PREP(PLLDIG_SSCGBYP_ENABLE, 0x0);
+
+	writel(val, data->regs + PLLDIG_REG_PLLFM);
+}
+
+static int plldig_is_enabled(struct clk_hw *hw)
+{
+	struct clk_plldig *data = to_clk_plldig(hw);
+
+	return readl(data->regs + PLLDIG_REG_PLLFM) &
+			      PLLDIG_SSCGBYP_ENABLE;
+}
+
+static unsigned long plldig_recalc_rate(struct clk_hw *hw,
+					unsigned long parent_rate)
+{
+	struct clk_plldig *data = to_clk_plldig(hw);
+	u32 val, rfdphi1;
+
+	val = readl(data->regs + PLLDIG_REG_PLLDV);
+
+	/* Check if PLL is bypassed */
+	if (val & PLLDIG_SSCGBYP_ENABLE)
+		return parent_rate;
+
+	rfdphi1 = FIELD_GET(PLLDIG_RFDPHI1_MASK, val);
+
+	/*
+	 * If RFDPHI1 has a value of 1 the VCO frequency is also divided by
+	 * one.
+	 */
+	if (!rfdphi1)
+		rfdphi1 = 1;
+
+	return DIV_ROUND_UP(data->vco_freq, rfdphi1);
+}
+
+static unsigned long plldig_calc_target_div(unsigned long vco_freq,
+					    unsigned long target_rate)
+{
+	unsigned long div;
+
+	div = DIV_ROUND_CLOSEST(vco_freq, target_rate);
+	div = clamp(div, 1UL, MAX_RFDPHI1);
+
+	return div;
+}
+
+static int plldig_determine_rate(struct clk_hw *hw,
+				 struct clk_rate_request *req)
+{
+	struct clk_plldig *data = to_clk_plldig(hw);
+	unsigned int div;
+
+	req->rate = clamp(req->rate, PHI1_MIN_FREQ, PHI1_MAX_FREQ);
+	div = plldig_calc_target_div(data->vco_freq, req->rate);
+	req->rate = DIV_ROUND_UP(data->vco_freq, div);
+
+	return 0;
+}
+
+static int plldig_set_rate(struct clk_hw *hw, unsigned long rate,
+		unsigned long parent_rate)
+{
+	struct clk_plldig *data = to_clk_plldig(hw);
+	unsigned int val, cond;
+	unsigned int rfdphi1;
+
+	rate = clamp(rate, PHI1_MIN_FREQ, PHI1_MAX_FREQ);
+	rfdphi1 = plldig_calc_target_div(data->vco_freq, rate);
+
+	/* update the divider value */
+	val = readl(data->regs + PLLDIG_REG_PLLDV);
+	val &= ~PLLDIG_RFDPHI1_MASK;
+	val |= FIELD_PREP(PLLDIG_RFDPHI1_MASK, rfdphi1);
+	writel(val, data->regs + PLLDIG_REG_PLLDV);
+
+	/* waiting for old lock state to clear */
+	udelay(200);
+
+	/* Wait until PLL is locked or timeout */
+	return readl_poll_timeout_atomic(data->regs + PLLDIG_REG_PLLSR, cond,
+					 cond & PLLDIG_LOCK_MASK, 0,
+					 USEC_PER_MSEC);
+}
+
+static const struct clk_ops plldig_clk_ops = {
+	.enable = plldig_enable,
+	.disable = plldig_disable,
+	.is_enabled = plldig_is_enabled,
+	.recalc_rate = plldig_recalc_rate,
+	.determine_rate = plldig_determine_rate,
+	.set_rate = plldig_set_rate,
+};
+
+static int plldig_init(struct clk_hw *hw)
+{
+	struct clk_plldig *data = to_clk_plldig(hw);
+	struct clk_hw *parent = clk_hw_get_parent(hw);
+	unsigned long parent_rate = clk_hw_get_rate(parent);
+	unsigned long val;
+	unsigned long long lltmp;
+	unsigned int mfd, fracdiv = 0;
+
+	if (!parent)
+		return -EINVAL;
+
+	if (data->vco_freq) {
+		mfd = data->vco_freq / parent_rate;
+		lltmp = data->vco_freq % parent_rate;
+		lltmp *= MFDEN;
+		do_div(lltmp, parent_rate);
+		fracdiv = lltmp;
+	} else {
+		mfd = PLLDIG_DEFAULT_MFD;
+		data->vco_freq = parent_rate * mfd;
+	}
+
+	val = FIELD_PREP(PLLDIG_MFD_MASK, mfd);
+	writel(val, data->regs + PLLDIG_REG_PLLDV);
+
+	/* Enable fractional divider */
+	if (fracdiv) {
+		val = FIELD_PREP(PLLDIG_FRAC_MASK, fracdiv);
+		val |= PLLDIG_FDEN;
+		writel(val, data->regs + PLLDIG_REG_PLLFD);
+	}
+
+	return 0;
+}
+
+static int plldig_clk_probe(struct platform_device *pdev)
+{
+	struct clk_plldig *data;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(data->regs))
+		return PTR_ERR(data->regs);
+
+	data->hw.init = CLK_HW_INIT_PARENTS_DATA("dpclk",
+						 parent_data,
+						 &plldig_clk_ops,
+						 0);
+
+	ret = devm_clk_hw_register(dev, &data->hw);
+	if (ret) {
+		dev_err(dev, "failed to register %s clock\n",
+						dev->of_node->name);
+		return ret;
+	}
+
+	ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get,
+					  &data->hw);
+	if (ret) {
+		dev_err(dev, "unable to add clk provider\n");
+		return ret;
+	}
+
+	/*
+	 * The frequency of the VCO cannot be changed during runtime.
+	 * Therefore, let the user specify a desired frequency.
+	 */
+	if (!of_property_read_u32(dev->of_node, "fsl,vco-hz",
+				  &data->vco_freq)) {
+		if (data->vco_freq < PLLDIG_MIN_VCO_FREQ ||
+		    data->vco_freq > PLLDIG_MAX_VCO_FREQ)
+			return -EINVAL;
+	}
+
+	return plldig_init(&data->hw);
+}
+
+static const struct of_device_id plldig_clk_id[] = {
+	{ .compatible = "fsl,ls1028a-plldig" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, plldig_clk_id);
+
+static struct platform_driver plldig_clk_driver = {
+	.driver = {
+		.name = "plldig-clock",
+		.of_match_table = plldig_clk_id,
+	},
+	.probe = plldig_clk_probe,
+};
+module_platform_driver(plldig_clk_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Wen He <wen.he_1@nxp.com>");
+MODULE_DESCRIPTION("LS1028A Display output interface pixel clock driver");

drivers/clk/clk-qoriq.c

@@ -342,6 +342,32 @@ static const struct clockgen_muxinfo ls1046a_hwa2 = {
 	},
 };
 
+static const struct clockgen_muxinfo ls1088a_hwa1 = {
+	{
+		{},
+		{ CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+		{ CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+		{ CLKSEL_VALID, CGA_PLL1, PLL_DIV3 },
+		{ CLKSEL_VALID, CGA_PLL1, PLL_DIV4 },
+		{},
+		{ CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+		{ CLKSEL_VALID, CGA_PLL2, PLL_DIV3 },
+	},
+};
+
+static const struct clockgen_muxinfo ls1088a_hwa2 = {
+	{
+		{},
+		{ CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+		{ CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+		{ CLKSEL_VALID, CGA_PLL2, PLL_DIV3 },
+		{ CLKSEL_VALID, CGA_PLL2, PLL_DIV4 },
+		{},
+		{ CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+		{ CLKSEL_VALID, CGA_PLL1, PLL_DIV3 },
+	},
+};
+
 static const struct clockgen_muxinfo ls1012a_cmux = {
 	{
 		[0] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
@@ -607,6 +633,9 @@ static const struct clockgen_chipinfo chipinfo[] = {
 		.cmux_groups = {
 			&clockgen2_cmux_cga12
 		},
+		.hwaccel = {
+			&ls1088a_hwa1, &ls1088a_hwa2
+		},
 		.cmux_to_group = {
 			0, 0, -1
 		},

drivers/clk/imx/Kconfig

@@ -20,6 +20,12 @@ config CLK_IMX8MN
 	help
 	    Build the driver for i.MX8MN CCM Clock Driver
 
+config CLK_IMX8MP
+	bool "IMX8MP CCM Clock Driver"
+	depends on ARCH_MXC && ARM64
+	help
+	    Build the driver for i.MX8MP CCM Clock Driver
+
 config CLK_IMX8MQ
 	bool "IMX8MQ CCM Clock Driver"
 	depends on ARCH_MXC && ARM64

drivers/clk/imx/Makefile

@@ -18,7 +18,7 @@ obj-$(CONFIG_MXC_CLK) += \
 	clk-pllv2.o \
 	clk-pllv3.o \
 	clk-pllv4.o \
-	clk-sccg-pll.o \
+	clk-sscg-pll.o \
 	clk-pll14xx.o
 
 obj-$(CONFIG_MXC_CLK_SCU) += \
@@ -27,6 +27,7 @@ obj-$(CONFIG_MXC_CLK_SCU) += \
 
 obj-$(CONFIG_CLK_IMX8MM) += clk-imx8mm.o
 obj-$(CONFIG_CLK_IMX8MN) += clk-imx8mn.o
+obj-$(CONFIG_CLK_IMX8MP) += clk-imx8mp.o
 obj-$(CONFIG_CLK_IMX8MQ) += clk-imx8mq.o
 obj-$(CONFIG_CLK_IMX8QXP) += clk-imx8qxp.o clk-imx8qxp-lpcg.o
 

drivers/clk/imx/clk-composite-7ulp.c

@@ -21,7 +21,7 @@
 #define PCG_PCD_WIDTH	3
 #define PCG_PCD_MASK	0x7
 
-struct clk_hw *imx7ulp_clk_composite(const char *name,
+struct clk_hw *imx7ulp_clk_hw_composite(const char *name,
 				     const char * const *parent_names,
 				     int num_parents, bool mux_present,
 				     bool rate_present, bool gate_present,

drivers/clk/imx/clk-composite-8m.c

@@ -123,7 +123,7 @@ static const struct clk_ops imx8m_clk_composite_divider_ops = {
 	.set_rate = imx8m_clk_composite_divider_set_rate,
 };
 
-struct clk *imx8m_clk_composite_flags(const char *name,
+struct clk_hw *imx8m_clk_hw_composite_flags(const char *name,
 					const char * const *parent_names,
 					int num_parents, void __iomem *reg,
 					unsigned long flags)
@@ -171,7 +171,7 @@ struct clk *imx8m_clk_composite_flags(const char *name,
 	if (IS_ERR(hw))
 		goto fail;
 
-	return hw->clk;
+	return hw;
 
 fail:
 	kfree(gate);

drivers/clk/imx/clk-divider-gate.c

@@ -43,7 +43,7 @@ static unsigned long clk_divider_gate_recalc_rate(struct clk_hw *hw,
 {
 	struct clk_divider_gate *div_gate = to_clk_divider_gate(hw);
 	struct clk_divider *div = to_clk_divider(hw);
-	unsigned long flags = 0;
+	unsigned long flags;
 	unsigned int val;
 
 	spin_lock_irqsave(div->lock, flags);
@@ -75,7 +75,7 @@ static int clk_divider_gate_set_rate(struct clk_hw *hw, unsigned long rate,
 {
 	struct clk_divider_gate *div_gate = to_clk_divider_gate(hw);
 	struct clk_divider *div = to_clk_divider(hw);
-	unsigned long flags = 0;
+	unsigned long flags;
 	int value;
 	u32 val;
 
@@ -104,7 +104,7 @@ static int clk_divider_enable(struct clk_hw *hw)
 {
 	struct clk_divider_gate *div_gate = to_clk_divider_gate(hw);
 	struct clk_divider *div = to_clk_divider(hw);
-	unsigned long flags = 0;
+	unsigned long flags;
 	u32 val;
 
 	if (!div_gate->cached_val) {
@@ -127,7 +127,7 @@ static void clk_divider_disable(struct clk_hw *hw)
 {
 	struct clk_divider_gate *div_gate = to_clk_divider_gate(hw);
 	struct clk_divider *div = to_clk_divider(hw);
-	unsigned long flags = 0;
+	unsigned long flags;
 	u32 val;
 
 	spin_lock_irqsave(div->lock, flags);
@@ -167,13 +167,13 @@ static const struct clk_ops clk_divider_gate_ops = {
 };
 
 /*
- * NOTE: In order to resue the most code from the common divider,
+ * NOTE: In order to reuse the most code from the common divider,
  * we also design our divider following the way that provids an extra
  * clk_divider_flags, however it's fixed to CLK_DIVIDER_ONE_BASED by
  * default as our HW is. Besides that it supports only CLK_DIVIDER_READ_ONLY
  * flag which can be specified by user flexibly.
  */
-struct clk_hw *imx_clk_divider_gate(const char *name, const char *parent_name,
+struct clk_hw *imx_clk_hw_divider_gate(const char *name, const char *parent_name,
 				    unsigned long flags, void __iomem *reg,
 				    u8 shift, u8 width, u8 clk_divider_flags,
 				    const struct clk_div_table *table,

drivers/clk/imx/clk-frac-pll.c

@@ -201,7 +201,8 @@ static const struct clk_ops clk_frac_pll_ops = {
 	.set_rate	= clk_pll_set_rate,
 };
 
-struct clk *imx_clk_frac_pll(const char *name, const char *parent_name,
+struct clk_hw *imx_clk_hw_frac_pll(const char *name,
+				   const char *parent_name,
 				   void __iomem *base)
 {
 	struct clk_init_data init;
@@ -230,5 +231,5 @@ struct clk *imx_clk_frac_pll(const char *name, const char *parent_name,
 		return ERR_PTR(ret);
 	}
 
-	return hw->clk;
+	return hw;
 }

drivers/clk/imx/clk-imx6q.c

@@ -598,6 +598,9 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 	}
 
 	hws[IMX6QDL_CLK_PLL4_POST_DIV] = clk_hw_register_divider_table(NULL, "pll4_post_div", "pll4_audio", CLK_SET_RATE_PARENT, base + 0x70, 19, 2, 0, post_div_table, &imx_ccm_lock);
+	if (clk_on_imx6q() || clk_on_imx6qp())
+		hws[IMX6QDL_CLK_PLL4_AUDIO_DIV] = imx_clk_hw_fixed_factor("pll4_audio_div", "pll4_post_div", 1, 1);
+	else
 		hws[IMX6QDL_CLK_PLL4_AUDIO_DIV] = clk_hw_register_divider(NULL, "pll4_audio_div", "pll4_post_div", CLK_SET_RATE_PARENT, base + 0x170, 15, 1, 0, &imx_ccm_lock);
 	hws[IMX6QDL_CLK_PLL5_POST_DIV] = clk_hw_register_divider_table(NULL, "pll5_post_div", "pll5_video", CLK_SET_RATE_PARENT, base + 0xa0, 19, 2, 0, post_div_table, &imx_ccm_lock);
 	hws[IMX6QDL_CLK_PLL5_VIDEO_DIV] = clk_hw_register_divider_table(NULL, "pll5_video_div", "pll5_post_div", CLK_SET_RATE_PARENT, base + 0x170, 30, 2, 0, video_div_table, &imx_ccm_lock);

drivers/clk/imx/clk-imx8qxp-lpcg.c

@@ -173,6 +173,17 @@ static int imx8qxp_lpcg_clk_probe(struct platform_device *pdev)
 	if (!ss_lpcg)
 		return -ENODEV;
 
+	/*
+	 * Please don't replace this with devm_platform_ioremap_resource.
+	 *
+	 * devm_platform_ioremap_resource calls devm_ioremap_resource which
+	 * differs from devm_ioremap by also calling devm_request_mem_region
+	 * and preventing other mappings in the same area.
+	 *
+	 * On imx8 the LPCG nodes map entire subsystems and overlap
+	 * peripherals, this means that using devm_platform_ioremap_resource
+	 * will cause many devices to fail to probe including serial ports.
+	 */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res)
 		return -EINVAL;

drivers/clk/imx/clk-pfdv2.c

@@ -166,7 +166,7 @@ static const struct clk_ops clk_pfdv2_ops = {
 	.is_enabled     = clk_pfdv2_is_enabled,
 };
 
-struct clk_hw *imx_clk_pfdv2(const char *name, const char *parent_name,
+struct clk_hw *imx_clk_hw_pfdv2(const char *name, const char *parent_name,
 			     void __iomem *reg, u8 idx)
 {
 	struct clk_init_data init;

drivers/clk/imx/clk-pll14xx.c

@@ -67,6 +67,13 @@ struct imx_pll14xx_clk imx_1443x_pll = {
 	.rate_count = ARRAY_SIZE(imx_pll1443x_tbl),
 };
 
+struct imx_pll14xx_clk imx_1443x_dram_pll = {
+	.type = PLL_1443X,
+	.rate_table = imx_pll1443x_tbl,
+	.rate_count = ARRAY_SIZE(imx_pll1443x_tbl),
+	.flags = CLK_GET_RATE_NOCACHE,
+};
+
 struct imx_pll14xx_clk imx_1416x_pll = {
 	.type = PLL_1416X,
 	.rate_table = imx_pll1416x_tbl,
@@ -369,13 +376,14 @@ static const struct clk_ops clk_pll1443x_ops = {
 	.set_rate	= clk_pll1443x_set_rate,
 };
 
-struct clk *imx_clk_pll14xx(const char *name, const char *parent_name,
+struct clk_hw *imx_clk_hw_pll14xx(const char *name, const char *parent_name,
 				  void __iomem *base,
 				  const struct imx_pll14xx_clk *pll_clk)
 {
 	struct clk_pll14xx *pll;
-	struct clk *clk;
+	struct clk_hw *hw;
 	struct clk_init_data init;
+	int ret;
 	u32 val;
 
 	pll = kzalloc(sizeof(*pll), GFP_KERNEL);
@@ -412,12 +420,15 @@ struct clk *imx_clk_pll14xx(const char *name, const char *parent_name,
 	val &= ~BYPASS_MASK;
 	writel_relaxed(val, pll->base + GNRL_CTL);
 
-	clk = clk_register(NULL, &pll->hw);
-	if (IS_ERR(clk)) {
-		pr_err("%s: failed to register pll %s %lu\n",
-			__func__, name, PTR_ERR(clk));
+	hw = &pll->hw;
+
+	ret = clk_hw_register(NULL, hw);
+	if (ret) {
+		pr_err("%s: failed to register pll %s %d\n",
+			__func__, name, ret);
 		kfree(pll);
+		return ERR_PTR(ret);
 	}
 
-	return clk;
+	return hw;
 }

drivers/clk/imx/clk-pllv1.c

@@ -111,12 +111,13 @@ static const struct clk_ops clk_pllv1_ops = {
 	.recalc_rate = clk_pllv1_recalc_rate,
 };
 
-struct clk *imx_clk_pllv1(enum imx_pllv1_type type, const char *name,
+struct clk_hw *imx_clk_hw_pllv1(enum imx_pllv1_type type, const char *name,
 		const char *parent, void __iomem *base)
 {
 	struct clk_pllv1 *pll;
-	struct clk *clk;
+	struct clk_hw *hw;
 	struct clk_init_data init;
+	int ret;
 
 	pll = kmalloc(sizeof(*pll), GFP_KERNEL);
 	if (!pll)
@@ -132,10 +133,13 @@ struct clk *imx_clk_pllv1(enum imx_pllv1_type type, const char *name,
 	init.num_parents = 1;
 
 	pll->hw.init = &init;
+	hw = &pll->hw;
 
-	clk = clk_register(NULL, &pll->hw);
-	if (IS_ERR(clk))
+	ret = clk_hw_register(NULL, hw);
+	if (ret) {
 		kfree(pll);
+		return ERR_PTR(ret);
+	}
 
-	return clk;
+	return hw;
 }

drivers/clk/imx/clk-pllv2.c

@@ -239,12 +239,13 @@ static const struct clk_ops clk_pllv2_ops = {
 	.set_rate = clk_pllv2_set_rate,
 };
 
-struct clk *imx_clk_pllv2(const char *name, const char *parent,
+struct clk_hw *imx_clk_hw_pllv2(const char *name, const char *parent,
 		void __iomem *base)
 {
 	struct clk_pllv2 *pll;
-	struct clk *clk;
+	struct clk_hw *hw;
 	struct clk_init_data init;
+	int ret;
 
 	pll = kzalloc(sizeof(*pll), GFP_KERNEL);
 	if (!pll)
@@ -259,10 +260,13 @@ struct clk *imx_clk_pllv2(const char *name, const char *parent,
 	init.num_parents = 1;
 
 	pll->hw.init = &init;
+	hw = &pll->hw;
 
-	clk = clk_register(NULL, &pll->hw);
-	if (IS_ERR(clk))
+	ret = clk_hw_register(NULL, hw);
+	if (ret) {
 		kfree(pll);
+		return ERR_PTR(ret);
+	}
 
-	return clk;
+	return hw;
 }

drivers/clk/imx/clk-pllv4.c

@@ -206,7 +206,7 @@ static const struct clk_ops clk_pllv4_ops = {
 	.is_enabled	= clk_pllv4_is_enabled,
 };
 
-struct clk_hw *imx_clk_pllv4(const char *name, const char *parent_name,
+struct clk_hw *imx_clk_hw_pllv4(const char *name, const char *parent_name,
 			  void __iomem *base)
 {
 	struct clk_pllv4 *pll;

drivers/clk/imx/clk.c

@@ -22,6 +22,14 @@ void imx_unregister_clocks(struct clk *clks[], unsigned int count)
 		clk_unregister(clks[i]);
 }
 
+void imx_unregister_hw_clocks(struct clk_hw *hws[], unsigned int count)
+{
+	unsigned int i;
+
+	for (i = 0; i < count; i++)
+		clk_hw_unregister(hws[i]);
+}
+
 void __init imx_mmdc_mask_handshake(void __iomem *ccm_base,
 				    unsigned int chn)
 {
@@ -94,7 +102,7 @@ struct clk_hw * __init imx_obtain_fixed_clock_hw(
 	return __clk_get_hw(clk);
 }
 
-struct clk_hw * __init imx_obtain_fixed_clk_hw(struct device_node *np,
+struct clk_hw * imx_obtain_fixed_clk_hw(struct device_node *np,
 					const char *name)
 {
 	struct clk *clk;

drivers/clk/qcom/clk-rcg.h

@@ -161,6 +161,7 @@ extern const struct clk_ops clk_byte2_ops;
 extern const struct clk_ops clk_pixel_ops;
 extern const struct clk_ops clk_gfx3d_ops;
 extern const struct clk_ops clk_rcg2_shared_ops;
+extern const struct clk_ops clk_dp_ops;
 
 struct clk_rcg_dfs_data {
 	struct clk_rcg2 *rcg;