Commit dc96efb7 authored by Matt Schulte's avatar Matt Schulte Committed by Greg Kroah-Hartman

Serial: Add support for new devices: Exar's XR17V35x family of multi-port PCIe UARTs

Add support for new devices: Exar's XR17V35x family of multi-port PCIe UARTs.
Signed-off-by: default avatarMatt Schulte <matts@commtech-fastcom.com>
Acked-by: default avatarAlan Cox <alan@linux.intel.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent ae8d8a14
......@@ -282,6 +282,15 @@ static const struct serial8250_config uart_config[] = {
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR,
},
[PORT_XR17V35X] = {
.name = "XR17V35X",
.fifo_size = 256,
.tx_loadsz = 256,
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 |
UART_FCR_T_TRIG_11,
.flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
UART_CAP_SLEEP,
},
[PORT_LPC3220] = {
.name = "LPC3220",
.fifo_size = 64,
......@@ -455,6 +464,7 @@ static void io_serial_out(struct uart_port *p, int offset, int value)
}
static int serial8250_default_handle_irq(struct uart_port *port);
static int exar_handle_irq(struct uart_port *port);
static void set_io_from_upio(struct uart_port *p)
{
......@@ -574,6 +584,18 @@ EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos);
*/
static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
{
/*
* Exar UARTs have a SLEEP register that enables or disables
* each UART to enter sleep mode separately. On the XR17V35x the
* register is accessible to each UART at the UART_EXAR_SLEEP
* offset but the UART channel may only write to the corresponding
* bit.
*/
if (p->port.type == PORT_XR17V35X) {
serial_out(p, UART_EXAR_SLEEP, 0xff);
return;
}
if (p->capabilities & UART_CAP_SLEEP) {
if (p->capabilities & UART_CAP_EFR) {
serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
......@@ -881,6 +903,27 @@ static void autoconfig_16550a(struct uart_8250_port *up)
up->port.type = PORT_16550A;
up->capabilities |= UART_CAP_FIFO;
/*
* XR17V35x UARTs have an extra divisor register, DLD
* that gets enabled with when DLAB is set which will
* cause the device to incorrectly match and assign
* port type to PORT_16650. The EFR for this UART is
* found at offset 0x09. Instead check the Deice ID (DVID)
* register for a 2, 4 or 8 port UART.
*/
status1 = serial_in(up, UART_EXAR_DVID);
if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) {
if (up->port.flags & UPF_EXAR_EFR) {
DEBUG_AUTOCONF("Exar XR17V35x ");
up->port.type = PORT_XR17V35X;
up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
UART_CAP_SLEEP;
return;
}
}
/*
* Check for presence of the EFR when DLAB is set.
* Only ST16C650V1 UARTs pass this test.
......@@ -1515,6 +1558,30 @@ static int serial8250_default_handle_irq(struct uart_port *port)
return serial8250_handle_irq(port, iir);
}
/*
* These Exar UARTs have an extra interrupt indicator that could
* fire for a few unimplemented interrupts. One of which is a
* wakeup event when coming out of sleep. Put this here just
* to be on the safe side that these interrupts don't go unhandled.
*/
static int exar_handle_irq(struct uart_port *port)
{
unsigned char int0, int1, int2, int3;
unsigned int iir = serial_port_in(port, UART_IIR);
int ret;
ret = serial8250_handle_irq(port, iir);
if (port->type == PORT_XR17V35X) {
int0 = serial_port_in(port, 0x80);
int1 = serial_port_in(port, 0x81);
int2 = serial_port_in(port, 0x82);
int3 = serial_port_in(port, 0x83);
}
return ret;
}
/*
* This is the serial driver's interrupt routine.
*
......@@ -2614,6 +2681,10 @@ static void serial8250_config_port(struct uart_port *port, int flags)
serial8250_release_rsa_resource(up);
if (port->type == PORT_UNKNOWN)
serial8250_release_std_resource(up);
/* Fixme: probably not the best place for this */
if (port->type == PORT_XR17V35X)
port->handle_irq = exar_handle_irq;
}
static int
......
......@@ -1164,6 +1164,39 @@ pci_xr17c154_setup(struct serial_private *priv,
return pci_default_setup(priv, board, port, idx);
}
static int
pci_xr17v35x_setup(struct serial_private *priv,
const struct pciserial_board *board,
struct uart_8250_port *port, int idx)
{
u8 __iomem *p;
p = pci_ioremap_bar(priv->dev, 0);
port->port.flags |= UPF_EXAR_EFR;
/*
* Setup Multipurpose Input/Output pins.
*/
if (idx == 0) {
writeb(0x00, p + 0x8f); /*MPIOINT[7:0]*/
writeb(0x00, p + 0x90); /*MPIOLVL[7:0]*/
writeb(0x00, p + 0x91); /*MPIO3T[7:0]*/
writeb(0x00, p + 0x92); /*MPIOINV[7:0]*/
writeb(0x00, p + 0x93); /*MPIOSEL[7:0]*/
writeb(0x00, p + 0x94); /*MPIOOD[7:0]*/
writeb(0x00, p + 0x95); /*MPIOINT[15:8]*/
writeb(0x00, p + 0x96); /*MPIOLVL[15:8]*/
writeb(0x00, p + 0x97); /*MPIO3T[15:8]*/
writeb(0x00, p + 0x98); /*MPIOINV[15:8]*/
writeb(0x00, p + 0x99); /*MPIOSEL[15:8]*/
writeb(0x00, p + 0x9a); /*MPIOOD[15:8]*/
}
iounmap(p);
return pci_default_setup(priv, board, port, idx);
}
static int
pci_wch_ch353_setup(struct serial_private *priv,
const struct pciserial_board *board,
......@@ -1622,6 +1655,27 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.subdevice = PCI_ANY_ID,
.setup = pci_xr17c154_setup,
},
{
.vendor = PCI_VENDOR_ID_EXAR,
.device = PCI_DEVICE_ID_EXAR_XR17V352,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_xr17v35x_setup,
},
{
.vendor = PCI_VENDOR_ID_EXAR,
.device = PCI_DEVICE_ID_EXAR_XR17V354,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_xr17v35x_setup,
},
{
.vendor = PCI_VENDOR_ID_EXAR,
.device = PCI_DEVICE_ID_EXAR_XR17V358,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_xr17v35x_setup,
},
/*
* Xircom cards
*/
......@@ -1962,6 +2016,9 @@ enum pci_board_num_t {
pbn_exar_XR17C152,
pbn_exar_XR17C154,
pbn_exar_XR17C158,
pbn_exar_XR17V352,
pbn_exar_XR17V354,
pbn_exar_XR17V358,
pbn_exar_ibm_saturn,
pbn_pasemi_1682M,
pbn_ni8430_2,
......@@ -2580,6 +2637,30 @@ static struct pciserial_board pci_boards[] = {
.base_baud = 921600,
.uart_offset = 0x200,
},
[pbn_exar_XR17V352] = {
.flags = FL_BASE0,
.num_ports = 2,
.base_baud = 7812500,
.uart_offset = 0x400,
.reg_shift = 0,
.first_offset = 0,
},
[pbn_exar_XR17V354] = {
.flags = FL_BASE0,
.num_ports = 4,
.base_baud = 7812500,
.uart_offset = 0x400,
.reg_shift = 0,
.first_offset = 0,
},
[pbn_exar_XR17V358] = {
.flags = FL_BASE0,
.num_ports = 8,
.base_baud = 7812500,
.uart_offset = 0x400,
.reg_shift = 0,
.first_offset = 0,
},
[pbn_exar_ibm_saturn] = {
.flags = FL_BASE0,
.num_ports = 1,
......@@ -3826,6 +3907,21 @@ static struct pci_device_id serial_pci_tbl[] = {
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17C158 },
/*
* Exar Corp. XR17V35[248] Dual/Quad/Octal PCIe UARTs
*/
{ PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V352,
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17V352 },
{ PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V354,
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17V354 },
{ PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V358,
PCI_ANY_ID, PCI_ANY_ID,
0,
0, pbn_exar_XR17V358 },
/*
* Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke)
......
......@@ -1985,6 +1985,9 @@
#define PCI_DEVICE_ID_EXAR_XR17C152 0x0152
#define PCI_DEVICE_ID_EXAR_XR17C154 0x0154
#define PCI_DEVICE_ID_EXAR_XR17C158 0x0158
#define PCI_DEVICE_ID_EXAR_XR17V352 0x0352
#define PCI_DEVICE_ID_EXAR_XR17V354 0x0354
#define PCI_DEVICE_ID_EXAR_XR17V358 0x0358
#define PCI_VENDOR_ID_MICROGATE 0x13c0
#define PCI_DEVICE_ID_MICROGATE_USC 0x0010
......
......@@ -49,7 +49,8 @@
#define PORT_XR17D15X 21 /* Exar XR17D15x UART */
#define PORT_LPC3220 22 /* NXP LPC32xx SoC "Standard" UART */
#define PORT_8250_CIR 23 /* CIR infrared port, has its own driver */
#define PORT_MAX_8250 23 /* max port ID */
#define PORT_XR17V35X 24 /* Exar XR17V35x UARTs */
#define PORT_MAX_8250 24 /* max port ID */
/*
* ARM specific type numbers. These are not currently guaranteed
......
......@@ -367,5 +367,11 @@
#define UART_OMAP_MDR1_CIR_MODE 0x06 /* CIR mode */
#define UART_OMAP_MDR1_DISABLE 0x07 /* Disable (default state) */
/*
* These are definitions for the XR17V35X and XR17D15X
*/
#define UART_EXAR_SLEEP 0x8b /* Sleep mode */
#define UART_EXAR_DVID 0x8d /* Device identification */
#endif /* _LINUX_SERIAL_REG_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment