Merge master.kernel.org:/home/acme/BK/includes-2.5

into home.transmeta.com:/home/torvalds/v2.5/linux

drivers/isdn/hisax/bkm_a8.c

@@ -278,8 +278,6 @@ sct_alloc_io(u_int adr, u_int len)
 static struct pci_dev *dev_a8 __initdata = NULL;
 static u16  sub_vendor_id __initdata = 0;
 static u16  sub_sys_id __initdata = 0;
-static u_char pci_bus __initdata = 0;
-static u_char pci_device_fn __initdata = 0;
 static u_char pci_irq __initdata = 0;
 
 #endif /* CONFIG_PCI */
@@ -328,8 +326,6 @@ setup_sct_quadro(struct IsdnCard *card)
 					return(0);
 				pci_ioaddr1 = pci_resource_start(dev_a8, 1);
 				pci_irq = dev_a8->irq;
-				pci_bus = dev_a8->bus->number;
-				pci_device_fn = dev_a8->devfn;
 				found = 1;
 				break;
 			}
@@ -342,20 +338,17 @@ setup_sct_quadro(struct IsdnCard *card)
 		}
 #ifdef ATTEMPT_PCI_REMAPPING
 /* HACK: PLX revision 1 bug: PLX address bit 7 must not be set */
-		pcibios_read_config_byte(pci_bus, pci_device_fn,
-			PCI_REVISION_ID, &pci_rev_id);
+		pci_read_config_byte(dev_a8, PCI_REVISION_ID, &pci_rev_id);
 		if ((pci_ioaddr1 & 0x80) && (pci_rev_id == 1)) {
 			printk(KERN_WARNING "HiSax: %s (%s): PLX rev 1, remapping required!\n",
 				CardType[card->typ],
 				sct_quadro_subtypes[cs->subtyp]);
 			/* Restart PCI negotiation */
-			pcibios_write_config_dword(pci_bus, pci_device_fn,
-				PCI_BASE_ADDRESS_1, (u_int) - 1);
+			pci_write_config_dword(dev_a8, PCI_BASE_ADDRESS_1, (u_int) - 1);
 			/* Move up by 0x80 byte */
 			pci_ioaddr1 += 0x80;
 			pci_ioaddr1 &= PCI_BASE_ADDRESS_IO_MASK;
-			pcibios_write_config_dword(pci_bus, pci_device_fn,
-				PCI_BASE_ADDRESS_1, pci_ioaddr1);
+			pci_write_config_dword(dev_a8, PCI_BASE_ADDRESS_1, pci_ioaddr1);
 			dev_a8->resource[ 1].start = pci_ioaddr1;
 		}
 #endif /* End HACK */
@@ -366,11 +359,11 @@ setup_sct_quadro(struct IsdnCard *card)
 		       sct_quadro_subtypes[cs->subtyp]);
 		return (0);
 	}
-	pcibios_read_config_dword(pci_bus, pci_device_fn, PCI_BASE_ADDRESS_1, &pci_ioaddr1);
-	pcibios_read_config_dword(pci_bus, pci_device_fn, PCI_BASE_ADDRESS_2, &pci_ioaddr2);
-	pcibios_read_config_dword(pci_bus, pci_device_fn, PCI_BASE_ADDRESS_3, &pci_ioaddr3);
-	pcibios_read_config_dword(pci_bus, pci_device_fn, PCI_BASE_ADDRESS_4, &pci_ioaddr4);
-	pcibios_read_config_dword(pci_bus, pci_device_fn, PCI_BASE_ADDRESS_5, &pci_ioaddr5);
+	pci_read_config_dword(dev_a8, PCI_BASE_ADDRESS_1, &pci_ioaddr1);
+	pci_read_config_dword(dev_a8, PCI_BASE_ADDRESS_2, &pci_ioaddr2);
+	pci_read_config_dword(dev_a8, PCI_BASE_ADDRESS_3, &pci_ioaddr3);
+	pci_read_config_dword(dev_a8, PCI_BASE_ADDRESS_4, &pci_ioaddr4);
+	pci_read_config_dword(dev_a8, PCI_BASE_ADDRESS_5, &pci_ioaddr5);
 	if (!pci_ioaddr1 || !pci_ioaddr2 || !pci_ioaddr3 || !pci_ioaddr4 || !pci_ioaddr5) {
 		printk(KERN_WARNING "HiSax: %s (%s): No IO base address(es)\n",
 		       CardType[card->typ],

drivers/pci/Makefile

@@ -3,10 +3,10 @@
 #
 
 export-objs	:= access.o hotplug.o pci-driver.o pci.o pool.o \
-			probe.o proc.o search.o compat.o setup-bus.o
+			probe.o proc.o search.o setup-bus.o
 
 obj-y		+= access.o probe.o pci.o pool.o quirks.o \
-			compat.o names.o pci-driver.o search.o hotplug.o
+			names.o pci-driver.o search.o hotplug.o
 obj-$(CONFIG_PM)  += power.o
 obj-$(CONFIG_PROC_FS) += proc.o
 

drivers/pci/compat.c

-/*
- *	$Id: compat.c,v 1.1 1998/02/16 10:35:50 mj Exp $
- *
- *	PCI Bus Services -- Function For Backward Compatibility
- *
- *	Copyright 1998--2000 Martin Mares <mj@ucw.cz>
- */
-
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-
-/* Obsolete functions, these will be going away... */
-
-#define PCI_OP(rw,size,type)							\
-int pcibios_##rw##_config_##size (unsigned char bus, unsigned char dev_fn,	\
-				  unsigned char where, unsigned type val)	\
-{										\
-	struct pci_dev *dev = pci_find_slot(bus, dev_fn);			\
-	if (!dev) return PCIBIOS_DEVICE_NOT_FOUND;				\
-	return pci_##rw##_config_##size(dev, where, val);			\
-}
-
-PCI_OP(read, byte, char *)
-PCI_OP(read, word, short *)
-PCI_OP(read, dword, int *)
-PCI_OP(write, byte, char)
-PCI_OP(write, word, short)
-PCI_OP(write, dword, int)
-
-EXPORT_SYMBOL(pcibios_read_config_byte);
-EXPORT_SYMBOL(pcibios_read_config_word);
-EXPORT_SYMBOL(pcibios_read_config_dword);
-EXPORT_SYMBOL(pcibios_write_config_byte);
-EXPORT_SYMBOL(pcibios_write_config_word);
-EXPORT_SYMBOL(pcibios_write_config_dword);

drivers/pcmcia/cistpl.c

@@ -430,7 +430,10 @@ int pcmcia_get_first_tuple(client_handle_t handle, tuple_t *tuple)
 #ifdef CONFIG_CARDBUS
     if (s->state & SOCKET_CARDBUS) {
 	u_int ptr;
-	pcibios_read_config_dword(s->cap.cb_dev->subordinate->number, 0, 0x28, &ptr);
+	struct pci_dev *dev = pci_find_slot (s->cap.cb_dev->subordinate->number, 0);
+	if (!dev)
+	    return CS_BAD_HANDLE;
+	pci_read_config_dword(dev, 0x28, &ptr);
 	tuple->CISOffset = ptr & ~7;
 	SPACE(tuple->Flags) = (ptr & 7);
     } else

drivers/usb/core/config.c

@@ -109,7 +109,8 @@ static int usb_parse_interface(struct usb_interface *interface, unsigned char *b
 	interface->num_altsetting = 0;
 	interface->max_altsetting = USB_ALTSETTINGALLOC;
 
-	interface->altsetting = kmalloc(sizeof(struct usb_interface_descriptor) * interface->max_altsetting, GFP_KERNEL);
+	interface->altsetting = kmalloc(sizeof(*interface->altsetting) * interface->max_altsetting,
+					GFP_KERNEL);
 	
 	if (!interface->altsetting) {
 		err("couldn't kmalloc interface->altsetting");
@@ -118,29 +119,27 @@ static int usb_parse_interface(struct usb_interface *interface, unsigned char *b
 
 	while (size > 0) {
 		struct usb_interface_descriptor	*d;
-
+	
 		if (interface->num_altsetting >= interface->max_altsetting) {
-			void *ptr;
+			struct usb_host_interface *ptr;
 			int oldmas;
 
 			oldmas = interface->max_altsetting;
 			interface->max_altsetting += USB_ALTSETTINGALLOC;
 			if (interface->max_altsetting > USB_MAXALTSETTING) {
-				warn("too many alternate settings (max %d)",
-					USB_MAXALTSETTING);
+				warn("too many alternate settings (incr %d max %d)\n",
+					USB_ALTSETTINGALLOC, USB_MAXALTSETTING);
 				return -1;
 			}
 
-			ptr = interface->altsetting;
-			interface->altsetting = kmalloc(sizeof(struct usb_interface_descriptor) * interface->max_altsetting, GFP_KERNEL);
-			if (!interface->altsetting) {
+			ptr = kmalloc(sizeof(*ptr) * interface->max_altsetting, GFP_KERNEL);
+			if (ptr == NULL) {
 				err("couldn't kmalloc interface->altsetting");
-				interface->altsetting = ptr;
 				return -1;
 			}
-			memcpy(interface->altsetting, ptr, sizeof(struct usb_interface_descriptor) * oldmas);
-
-			kfree(ptr);
+			memcpy(ptr, interface->altsetting, sizeof(*interface->altsetting) * oldmas);
+			kfree(interface->altsetting);
+			interface->altsetting = ptr;
 		}
 
 		ifp = interface->altsetting + interface->num_altsetting;

drivers/usb/net/pegasus.h

@@ -85,6 +85,7 @@ typedef struct pegasus {
 	struct usb_device	*usb;
 	struct net_device	*net;
 	struct net_device_stats	stats;
+	struct mii_if_info	mii;
 	unsigned		flags;
 	unsigned		features;
 	int			dev_index;
@@ -97,6 +98,7 @@ typedef struct pegasus {
 	wait_queue_head_t	ctrl_wait;
 	struct semaphore	sem;
 	spinlock_t		rx_pool_lock;
+	int			chip;
 	unsigned char		intr_buff[8];
 	__u8			tx_buff[PEGASUS_MTU];
 	__u8			eth_regs[4];
@@ -131,11 +133,11 @@ struct usb_eth_dev {
 #define	VENDOR_LANEED		0x056e
 #define	VENDOR_LINKSYS		0x066b
 #define	VENDOR_MELCO		0x0411
+#define	VENDOR_NETGEAR		0x0846
 #define	VENDOR_SMARTBRIDGES	0x08d1
 #define	VENDOR_SMC		0x0707
 #define	VENDOR_SOHOWARE		0x15e8
 #define	VENDOR_SIEMENS		0x067c
-#define	VENDOR_JTEC		0x11ad
 
 
 #else	/* PEGASUS_DEV */
@@ -169,7 +171,10 @@ PEGASUS_DEV( "SpeedStream USB 10/100 Ethernet", VENDOR_ACCTON, 0x5046,
 PEGASUS_DEV( "ADMtek ADM8511 \"Pegasus II\" USB Ethernet",
 		VENDOR_ADMTEK, 0x8511,
 		DEFAULT_GPIO_RESET | PEGASUS_II )
-PEGASUS_DEV( "ADMtek AN986 \"Pegasus\" USB Ethernet (eval. board)",
+PEGASUS_DEV( "ADMtek ADM8513 \"Pegasus II\" USB Ethernet",
+		VENDOR_ADMTEK, 0x8513,
+		DEFAULT_GPIO_RESET | PEGASUS_II )
+PEGASUS_DEV( "ADMtek AN986 \"Pegasus\" USB Ethernet (evaluation board)",
 		VENDOR_ADMTEK, 0x0986,
 		DEFAULT_GPIO_RESET | HAS_HOME_PNA )
 PEGASUS_DEV( "AN986A USB MAC", VENDOR_ADMTEK, 1986,
@@ -192,7 +197,7 @@ PEGASUS_DEV( "Billionton USBE-100", VENDOR_BILLIONTON, 0x8511,
 		DEFAULT_GPIO_RESET | PEGASUS_II )
 PEGASUS_DEV( "Corega FEter USB-TX", VENDOR_COREGA, 0x0004,
 		DEFAULT_GPIO_RESET )
-PEGASUS_DEV( "Corega FEter", VENDOR_COREGA, 0x000d,
+PEGASUS_DEV( "Corega FEter USB-TXS", VENDOR_COREGA, 0x000d,
 		DEFAULT_GPIO_RESET | PEGASUS_II )
 PEGASUS_DEV( "D-Link DSB-650TX", VENDOR_DLINK, 0x4001,
 		LINKSYS_GPIO_RESET )
@@ -246,6 +251,8 @@ PEGASUS_DEV( "MELCO/BUFFALO LUA-TX", VENDOR_MELCO, 0x0005,
 		DEFAULT_GPIO_RESET )
 PEGASUS_DEV( "MELCO/BUFFALO LUA2-TX", VENDOR_MELCO, 0x0009,
 		DEFAULT_GPIO_RESET | PEGASUS_II )
+PEGASUS_DEV( "NETGEAR FA101", VENDOR_NETGEAR, 0x1020,
+		DEFAULT_GPIO_RESET | PEGASUS_II )
 PEGASUS_DEV( "smartNIC 2 PnP Adapter", VENDOR_SMARTBRIDGES, 0x0003,
 		DEFAULT_GPIO_RESET | PEGASUS_II )
 PEGASUS_DEV( "SMC 202 USB Ethernet", VENDOR_SMC, 0x0200,
@@ -258,8 +265,6 @@ PEGASUS_DEV( "SOHOware NUB110 Ethernet", VENDOR_SOHOWARE, 0x9110,
 		DEFAULT_GPIO_RESET | PEGASUS_II )
 PEGASUS_DEV( "SpeedStream USB 10/100 Ethernet", VENDOR_SIEMENS, 0x1001,
 		DEFAULT_GPIO_RESET | PEGASUS_II )
-PEGASUS_DEV( "FA8101 USB To ETHERNET", VENDOR_JTEC, 0x8101,
-		DEFAULT_GPIO_RESET | PEGASUS_II )
 
 
 #endif	/* PEGASUS_DEV */

drivers/usb/serial/usb-serial.c

@@ -14,6 +14,10 @@
  *
  * See Documentation/usb/usb-serial.txt for more information on using this driver
  *
+ * (11/19/2002) gkh
+ *	removed a few #ifdefs for the generic code and cleaned up the failure
+ *	logic in initialization.
+ *
  * (10/02/2002) gkh
  *	moved the console code to console.c and out of this file.
  *
@@ -341,7 +345,7 @@
 /*
  * Version Information
  */
-#define DRIVER_VERSION "v1.6"
+#define DRIVER_VERSION "v1.7"
 #define DRIVER_AUTHOR "Greg Kroah-Hartman, greg@kroah.com, http://www.kroah.com/linux/"
 #define DRIVER_DESC "USB Serial Driver core"
 
@@ -382,7 +386,29 @@ static struct usb_device_id generic_serial_ids[] = {
 	{.driver_info = 42},
 	{}
 };
-#endif
+
+static int generic_register (void)
+{
+	generic_device_ids[0].idVendor = vendor;
+	generic_device_ids[0].idProduct = product;
+	generic_device_ids[0].match_flags = USB_DEVICE_ID_MATCH_VENDOR | USB_DEVICE_ID_MATCH_PRODUCT;
+
+	/* register our generic driver with ourselves */
+	return usb_serial_register (&generic_device);
+}
+
+static void generic_deregister (void)
+{
+	/* remove our generic driver */
+	usb_serial_deregister (&generic_device);
+}
+
+#else
+
+static inline int generic_register (void) { return 0; }
+static inline void generic_deregister (void) { }
+
+#endif /* CONFIG_USB_SERIAL_GENERIC */
 
 /* Driver structure we register with the USB core */
 static struct usb_driver usb_serial_driver = {
@@ -409,7 +435,6 @@ static struct termios *		serial_termios_locked[SERIAL_TTY_MINORS];
 static struct usb_serial	*serial_table[SERIAL_TTY_MINORS];	/* initially all NULL */
 static LIST_HEAD(usb_serial_driver_list);
 
-
 struct usb_serial *usb_serial_get_by_minor (unsigned int minor)
 {
 	return serial_table[minor];
@@ -839,7 +864,7 @@ static int serial_read_proc (char *page, char **start, off_t off, int count, int
 
 		length += sprintf (page+length, "%d:", i);
 		if (serial->type->owner)
-			length += sprintf (page+length, " module:%s", serial->type->owner->name);
+			length += sprintf (page+length, " module:%s", module_name(serial->type->owner));
 		length += sprintf (page+length, " name:\"%s\"", serial->type->name);
 		length += sprintf (page+length, " vendor:%04x product:%04x", serial->vendor, serial->product);
 		length += sprintf (page+length, " num_ports:%d", serial->num_ports);
@@ -1574,40 +1599,49 @@ static struct tty_driver serial_tty_driver = {
 static int __init usb_serial_init(void)
 {
 	int i;
-	int result;
+	int result = 0;
 
 	/* Initalize our global data */
 	for (i = 0; i < SERIAL_TTY_MINORS; ++i) {
 		serial_table[i] = NULL;
 	}
 
+	/* register the generic driver, if we should */
+	result = generic_register();
+	if (result < 0) {
+		err("%s - registering generic driver failed", __FUNCTION__);
+		goto exit;
+	}
+
 	/* register the tty driver */
 	serial_tty_driver.init_termios          = tty_std_termios;
 	serial_tty_driver.init_termios.c_cflag  = B9600 | CS8 | CREAD | HUPCL | CLOCAL;
-	if (tty_register_driver (&serial_tty_driver)) {
-		err("%s - failed to register tty driver", __FUNCTION__);
-		return -1;
+	result = tty_register_driver (&serial_tty_driver);
+	if (result) {
+		err("%s - tty_register_driver failed", __FUNCTION__);
+		goto exit_generic;
 	}
 
 	/* register the USB driver */
 	result = usb_register(&usb_serial_driver);
 	if (result < 0) {
-		tty_unregister_driver(&serial_tty_driver);
-		err("usb_register failed for the usb-serial driver. Error number %d", result);
-		return -1;
+		err("%s - usb_register failed", __FUNCTION__);
+		goto exit_tty;
 	}
 
-#ifdef CONFIG_USB_SERIAL_GENERIC
-	generic_device_ids[0].idVendor = vendor;
-	generic_device_ids[0].idProduct = product;
-	generic_device_ids[0].match_flags = USB_DEVICE_ID_MATCH_VENDOR | USB_DEVICE_ID_MATCH_PRODUCT;
-	/* register our generic driver with ourselves */
-	usb_serial_register (&generic_device);
-#endif
-
 	info(DRIVER_DESC " " DRIVER_VERSION);
 
-	return 0;
+	return result;
+
+exit_tty:
+	tty_unregister_driver(&serial_tty_driver);
+
+exit_generic:
+	generic_deregister();
+
+exit:
+	err ("%s - returning with error %d", __FUNCTION__, result);
+	return result;
 }
 
 
@@ -1615,11 +1649,8 @@ static void __exit usb_serial_exit(void)
 {
 	usb_serial_console_exit();
 
-#ifdef CONFIG_USB_SERIAL_GENERIC
-	/* remove our generic driver */
-	usb_serial_deregister (&generic_device);
-#endif
-	
+	generic_deregister();
+
 	usb_deregister(&usb_serial_driver);
 	tty_unregister_driver(&serial_tty_driver);
 }

drivers/usb/storage/freecom.c

@@ -115,7 +115,7 @@ freecom_readdata (Scsi_Cmnd *srb, struct us_data *us,
         freecom_udata_t extra = (freecom_udata_t) us->extra;
         struct freecom_xfer_wrap *fxfr =
                 (struct freecom_xfer_wrap *) extra->buffer;
-        int result, partial;
+        int result;
 
         fxfr->Type = FCM_PACKET_INPUT | 0x00;
         fxfr->Timeout = 0;    /* Short timeout for debugging. */
@@ -125,14 +125,12 @@ freecom_readdata (Scsi_Cmnd *srb, struct us_data *us,
         US_DEBUGP("Read data Freecom! (c=%d)\n", count);
 
         /* Issue the transfer command. */
-        result = usb_stor_bulk_msg (us, fxfr, opipe,
-                        FCM_PACKET_LENGTH, &partial);
+        result = usb_stor_bulk_transfer_buf (us, opipe, fxfr,
+                        FCM_PACKET_LENGTH, NULL);
         if (result != USB_STOR_XFER_GOOD) {
-                US_DEBUGP ("Freecom readdata xport failure: r=%d, p=%d\n",
-                                result, partial);
+                US_DEBUGP ("Freecom readdata transport error\n");
                 return USB_STOR_TRANSPORT_ERROR;
         }
-        US_DEBUGP("Done issuing read request: %d %d\n", result, partial);
 
         /* Now transfer all of our blocks. */
 	US_DEBUGP("Start of read\n");
@@ -151,7 +149,7 @@ freecom_writedata (Scsi_Cmnd *srb, struct us_data *us,
         freecom_udata_t extra = (freecom_udata_t) us->extra;
         struct freecom_xfer_wrap *fxfr =
                 (struct freecom_xfer_wrap *) extra->buffer;
-        int result, partial;
+        int result;
 
         fxfr->Type = FCM_PACKET_OUTPUT | 0x00;
         fxfr->Timeout = 0;    /* Short timeout for debugging. */
@@ -161,15 +159,12 @@ freecom_writedata (Scsi_Cmnd *srb, struct us_data *us,
         US_DEBUGP("Write data Freecom! (c=%d)\n", count);
 
         /* Issue the transfer command. */
-        result = usb_stor_bulk_msg (us, fxfr, opipe,
-                        FCM_PACKET_LENGTH, &partial);
+        result = usb_stor_bulk_transfer_buf (us, opipe, fxfr,
+                        FCM_PACKET_LENGTH, NULL);
         if (result != USB_STOR_XFER_GOOD) {
-                US_DEBUGP ("Freecom writedata xport failure: r=%d, p=%d\n",
-                                result, partial);
+                US_DEBUGP ("Freecom writedata transport error\n");
                 return USB_STOR_TRANSPORT_ERROR;
         }
-        US_DEBUGP("Done issuing write request: %d %d\n",
-                        result, partial);
 
         /* Now transfer all of our blocks. */
 	US_DEBUGP("Start of write\n");
@@ -191,7 +186,7 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
         struct freecom_status  *fst;
         unsigned int ipipe, opipe;             /* We need both pipes. */
         int result;
-        int partial;
+	unsigned int partial;
         int length;
         freecom_udata_t extra;
 
@@ -215,23 +210,22 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
         US_DEBUG(pdump (srb->cmnd, 12));
 
         /* Send it out. */
-        result = usb_stor_bulk_msg (us, fcb, opipe,
-                        FCM_PACKET_LENGTH, &partial);
+        result = usb_stor_bulk_transfer_buf (us, opipe, fcb,
+                        FCM_PACKET_LENGTH, NULL);
 
         /* The Freecom device will only fail if there is something wrong in
          * USB land.  It returns the status in its own registers, which
          * come back in the bulk pipe. */
         if (result != USB_STOR_XFER_GOOD) {
-                US_DEBUGP ("freecom xport failure: r=%d, p=%d\n",
-                                result, partial);
+                US_DEBUGP ("freecom transport error\n");
                 return USB_STOR_TRANSPORT_ERROR;
         }
 
         /* There are times we can optimize out this status read, but it
          * doesn't hurt us to always do it now. */
-        result = usb_stor_bulk_msg (us, fst, ipipe,
+        result = usb_stor_bulk_transfer_buf (us, ipipe, fst,
                         FCM_PACKET_LENGTH, &partial);
-        US_DEBUGP("foo Status result %d %d\n", result, partial);
+        US_DEBUGP("foo Status result %d %u\n", result, partial);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_ERROR;
 
@@ -256,24 +250,23 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
 		memset (fcb->Filler, 0, sizeof (fcb->Filler));
 
         	/* Send it out. */
-		result = usb_stor_bulk_msg (us, fcb, opipe,
-				FCM_PACKET_LENGTH, &partial);
+		result = usb_stor_bulk_transfer_buf (us, opipe, fcb,
+				FCM_PACKET_LENGTH, NULL);
 
 		/* The Freecom device will only fail if there is something
 		 * wrong in USB land.  It returns the status in its own
 		 * registers, which come back in the bulk pipe.
 		 */
 		if (result != USB_STOR_XFER_GOOD) {
-			US_DEBUGP ("freecom xport failure: r=%d, p=%d\n",
-					result, partial);
+			US_DEBUGP ("freecom transport error\n");
 			return USB_STOR_TRANSPORT_ERROR;
 		}
 
 		/* get the data */
-        	result = usb_stor_bulk_msg (us, fst, ipipe,
+        	result = usb_stor_bulk_transfer_buf (us, ipipe, fst,
 				FCM_PACKET_LENGTH, &partial);
 
-		US_DEBUGP("bar Status result %d %d\n", result, partial);
+		US_DEBUGP("bar Status result %d %u\n", result, partial);
 		if (result > USB_STOR_XFER_SHORT)
 	                return USB_STOR_TRANSPORT_ERROR;
 
@@ -328,7 +321,7 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
                         return result;
 
                 US_DEBUGP("FCM: Waiting for status\n");
-                result = usb_stor_bulk_msg (us, fst, ipipe,
+                result = usb_stor_bulk_transfer_buf (us, ipipe, fst,
                                 FCM_PACKET_LENGTH, &partial);
 		US_DEBUG(pdump ((void *) fst, partial));
 
@@ -354,7 +347,7 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
                         return result;
 
                 US_DEBUGP("FCM: Waiting for status\n");
-                result = usb_stor_bulk_msg (us, fst, ipipe,
+                result = usb_stor_bulk_transfer_buf (us, ipipe, fst,
                                 FCM_PACKET_LENGTH, &partial);
 
                 if (partial != 4 || result > USB_STOR_XFER_SHORT)
@@ -385,13 +378,6 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
         }
 
         return USB_STOR_TRANSPORT_GOOD;
-
-        US_DEBUGP("Freecom: transfer_length = %d\n",
-			usb_stor_transfer_length (srb));
-
-        US_DEBUGP("Freecom: direction = %d\n", srb->sc_data_direction);
-
-        return USB_STOR_TRANSPORT_ERROR;
 }
 
 int

drivers/usb/storage/isd200.c

@@ -668,7 +668,7 @@ int isd200_write_config( struct us_data *us )
 #endif
 
 	/* let's send the command via the control pipe */
-	result = usb_stor_control_msg(
+	result = usb_stor_ctrl_transfer(
                 us, 
                 us->send_ctrl_pipe,
                 0x01, 
@@ -709,7 +709,7 @@ int isd200_read_config( struct us_data *us )
 	/* read the configuration information from ISD200.  Use this to */
 	/* determine what the special ATA CDB bytes are.                */
 
-	result = usb_stor_control_msg(
+	result = usb_stor_ctrl_transfer(
                 us, 
                 us->recv_ctrl_pipe,
                 0x02, 

drivers/usb/storage/transport.c

@@ -479,7 +479,7 @@ int usb_stor_control_msg(struct us_data *us, unsigned int pipe,
 			 usb_stor_blocking_completion, NULL);
 	status = usb_stor_msg_common(us);
 
-	/* return the actual length of the data transferred if no error*/
+	/* return the actual length of the data transferred if no error */
 	if (status >= 0)
 		status = us->current_urb->actual_length;
 	return status;
@@ -543,47 +543,91 @@ int usb_stor_clear_halt(struct us_data *us, unsigned int pipe)
 	return 0;
 }
 
+
 /*
- * Transfer one control message
+ * Interpret the results of a URB transfer
  *
- * This function does basically the same thing as usb_stor_control_msg()
- * above, except that return codes are USB_STOR_XFER_xxx rather than the
- * urb status or transfer length.
+ * This function prints appropriate debugging messages, clears halts on
+ * bulk endpoints, and translates the status to the corresponding
+ * USB_STOR_XFER_xxx return code.
  */
-int usb_stor_ctrl_transfer(struct us_data *us, unsigned int pipe,
-		u8 request, u8 requesttype, u16 value, u16 index,
-		void *data, u16 size) {
-	int result;
+static int interpret_urb_result(struct us_data *us, unsigned int pipe,
+		unsigned int length, int result, unsigned int partial) {
 
-	US_DEBUGP("usb_stor_ctrl_transfer(): rq=%02x rqtype=%02x "
-			"value=%04x index=%02x len=%d\n",
-			request, requesttype, value, index, size);
-	result = usb_stor_control_msg(us, pipe, request, requesttype,
-			value, index, data, size);
-	US_DEBUGP("usb_stor_control_msg returned %d\n", result);
+	US_DEBUGP("Status code %d; transferred %u/%u\n",
+			result, partial, length);
 
-	/* a stall indicates a protocol error */
+	/* stalled */
 	if (result == -EPIPE) {
-		US_DEBUGP("-- stall on control pipe\n");
+
+		/* for non-bulk (i.e., control) endpoints, a stall indicates
+		 * a protocol error */
+		if (!usb_pipebulk(pipe)) {
+			US_DEBUGP("-- stall on control pipe\n");
+			return USB_STOR_XFER_ERROR;
+		}
+
+		/* for a bulk endpoint, clear the stall */
+		US_DEBUGP("clearing endpoint halt for pipe 0x%x\n", pipe);
+		if (usb_stor_clear_halt(us, pipe) < 0)
+			return USB_STOR_XFER_ERROR;
+		return USB_STOR_XFER_STALLED;
+	}
+
+	/* NAK - that means we've retried this a few times already */
+	if (result == -ETIMEDOUT) {
+		US_DEBUGP("-- device NAKed\n");
+		return USB_STOR_XFER_ERROR;
+	}
+
+	/* the transfer was cancelled, presumably by an abort */
+	if (result == -ENODEV) {
+		US_DEBUGP("-- transfer cancelled\n");
 		return USB_STOR_XFER_ERROR;
 	}
 
-	/* some other serious problem here */
+	/* the catch-all error case */
 	if (result < 0) {
 		US_DEBUGP("-- unknown error\n");
 		return USB_STOR_XFER_ERROR;
 	}
 
-	/* was the entire command transferred? */
-	if (result < size) {
-		US_DEBUGP("-- transferred only %d bytes\n", result);
+	/* no error code; did we send all the data? */
+	if (partial != length) {
+		US_DEBUGP("-- transferred only %u bytes\n", partial);
 		return USB_STOR_XFER_SHORT;
 	}
 
-	US_DEBUGP("-- transfer completed successfully\n");
+	US_DEBUGP("-- transfer complete\n");
 	return USB_STOR_XFER_GOOD;
 }
 
+/*
+ * Transfer one control message
+ *
+ * This function does basically the same thing as usb_stor_control_msg()
+ * above, except that return codes are USB_STOR_XFER_xxx rather than the
+ * urb status or transfer length.
+ */
+int usb_stor_ctrl_transfer(struct us_data *us, unsigned int pipe,
+		u8 request, u8 requesttype, u16 value, u16 index,
+		void *data, u16 size) {
+	int result;
+	unsigned int partial = 0;
+
+	US_DEBUGP("usb_stor_ctrl_transfer(): rq=%02x rqtype=%02x "
+			"value=%04x index=%02x len=%u\n",
+			request, requesttype, value, index, size);
+	result = usb_stor_control_msg(us, pipe, request, requesttype,
+			value, index, data, size);
+
+	if (result > 0) {	/* Separate out the amount transferred */
+		partial = result;
+		result = 0;
+	}
+	return interpret_urb_result(us, pipe, size, result, partial);
+}
+
 /*
  * Transfer one buffer via bulk transfer
  *
@@ -596,50 +640,17 @@ int usb_stor_ctrl_transfer(struct us_data *us, unsigned int pipe,
  *	    urb status or transfer length.
  */
 int usb_stor_bulk_transfer_buf(struct us_data *us, unsigned int pipe,
-	char *buf, unsigned int length, unsigned int *act_len)
+	void *buf, unsigned int length, unsigned int *act_len)
 {
 	int result;
-	int partial;
+	unsigned int partial;
 
 	/* transfer the data */
-	US_DEBUGP("usb_stor_bulk_transfer_buf(): xfer %d bytes\n", length);
+	US_DEBUGP("usb_stor_bulk_transfer_buf(): xfer %u bytes\n", length);
 	result = usb_stor_bulk_msg(us, buf, pipe, length, &partial);
-	US_DEBUGP("usb_stor_bulk_msg() returned %d xferred %d/%d\n",
-		  result, partial, length);
 	if (act_len)
 		*act_len = partial;
-
-	/* if we stall, we need to clear it before we go on */
-	if (result == -EPIPE) {
-		US_DEBUGP("clearing endpoint halt for pipe 0x%x,"
-				" stalled at %d bytes\n", pipe, partial);
-		if (usb_stor_clear_halt(us, pipe) < 0)
-			return USB_STOR_XFER_ERROR;
-		return USB_STOR_XFER_STALLED;
-	}
-
-	/* NAK - that means we've retried a few times already */
-	if (result == -ETIMEDOUT) {
-		US_DEBUGP("-- device NAKed\n");
-		return USB_STOR_XFER_ERROR;
-	}
-
-	/* the catch-all error case */
-	if (result) {
-		US_DEBUGP("-- unknown error\n");
-		return USB_STOR_XFER_ERROR;
-	}
-
-	/* did we send all the data? */
-	if (partial == length) {
-		US_DEBUGP("-- transfer complete\n");
-		return USB_STOR_XFER_GOOD;
-	}
-
-	/* no error code, so we must have transferred some data, 
-	 * just not all of it */
-	US_DEBUGP("-- transferred only %d bytes\n", partial);
-	return USB_STOR_XFER_SHORT;
+	return interpret_urb_result(us, pipe, length, result, partial);
 }
 
 /*
@@ -653,10 +664,10 @@ int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
 		unsigned int *act_len)
 {
 	int result;
-	int partial;
+	unsigned int partial;
 
 	/* initialize the scatter-gather request block */
-	US_DEBUGP("usb_stor_bulk_transfer_sglist(): xfer %d bytes, "
+	US_DEBUGP("usb_stor_bulk_transfer_sglist(): xfer %u bytes, "
 			"%d entries\n", length, num_sg);
 	result = usb_sg_init(us->current_sg, us->pusb_dev, pipe, 0,
 			sg, num_sg, length, SLAB_NOIO);
@@ -685,55 +696,22 @@ int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
 
 	result = us->current_sg->status;
 	partial = us->current_sg->bytes;
-	US_DEBUGP("usb_sg_wait() returned %d xferred %d/%d\n",
-			result, partial, length);
 	if (act_len)
 		*act_len = partial;
-
-	/* if we stall, we need to clear it before we go on */
-	if (result == -EPIPE) {
-		US_DEBUGP("clearing endpoint halt for pipe 0x%x, "
-				"stalled at %d bytes\n", pipe, partial);
-		if (usb_stor_clear_halt(us, pipe) < 0)
-			return USB_STOR_XFER_ERROR;
-		return USB_STOR_XFER_STALLED;
-	}
-
-	/* NAK - that means we've retried this a few times already */
-	if (result == -ETIMEDOUT) {
-		US_DEBUGP("-- device NAKed\n");
-		return USB_STOR_XFER_ERROR;
-	}
-
-	/* the catch-all error case */
-	if (result) {
-		US_DEBUGP("-- unknown error\n");
-		return USB_STOR_XFER_ERROR;
-	}
-
-	/* did we send all the data? */
-	if (partial == length) {
-		US_DEBUGP("-- transfer complete\n");
-		return USB_STOR_XFER_GOOD;
-	}
-
-	/* no error code, so we must have transferred some data,
-	 * just not all of it */
-	US_DEBUGP("-- transferred only %d bytes\n", partial);
-	return USB_STOR_XFER_SHORT;
+	return interpret_urb_result(us, pipe, length, result, partial);
 }
 
 /*
  * Transfer an entire SCSI command's worth of data payload over the bulk
  * pipe.
  *
- * Nore that this uses usb_stor_bulk_transfer_buf() and
+ * Note that this uses usb_stor_bulk_transfer_buf() and
  * usb_stor_bulk_transfer_sglist() to achieve its goals --
  * this function simply determines whether we're going to use
  * scatter-gather or not, and acts appropriately.
  */
 int usb_stor_bulk_transfer_sg(struct us_data* us, unsigned int pipe,
-		char *buf, unsigned int length_left, int use_sg, int *residual)
+		void *buf, unsigned int length_left, int use_sg, int *residual)
 {
 	int result;
 	unsigned int partial;
@@ -1278,7 +1256,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 		  (bcb.Lun >> 4), (bcb.Lun & 0x0F), 
 		  le32_to_cpu(bcb.DataTransferLength), bcb.Flags, bcb.Length);
 	result = usb_stor_bulk_transfer_buf(us, us->send_bulk_pipe,
-				(char *) &bcb, US_BULK_CB_WRAP_LEN, NULL);
+				&bcb, US_BULK_CB_WRAP_LEN, NULL);
 	US_DEBUGP("Bulk command transfer result=%d\n", result);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_ERROR;
@@ -1302,7 +1280,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 	/* get CSW for device status */
 	US_DEBUGP("Attempting to get CSW...\n");
 	result = usb_stor_bulk_transfer_buf(us, us->recv_bulk_pipe,
-				(char *) &bcs, US_BULK_CS_WRAP_LEN, NULL);
+				&bcs, US_BULK_CS_WRAP_LEN, NULL);
 
 	/* did the attempt to read the CSW fail? */
 	if (result == USB_STOR_XFER_STALLED) {
@@ -1310,7 +1288,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 		/* get the status again */
 		US_DEBUGP("Attempting to get CSW (2nd try)...\n");
 		result = usb_stor_bulk_transfer_buf(us, us->recv_bulk_pipe,
-				(char *) &bcs, US_BULK_CS_WRAP_LEN, NULL);
+				&bcs, US_BULK_CS_WRAP_LEN, NULL);
 	}
 
 	/* if we still have a failure at this point, we're in trouble */

drivers/usb/storage/transport.h

@@ -117,6 +117,7 @@ struct bulk_cs_wrap {
 /*
  * usb_stor_bulk_transfer_xxx() return codes, in order of severity
  */
+
 #define USB_STOR_XFER_GOOD		0  /* good transfer                 */
 #define USB_STOR_XFER_SHORT		1  /* transfered less than expected */
 #define USB_STOR_XFER_STALLED		2  /* endpoint stalled		    */
@@ -129,7 +130,14 @@ struct bulk_cs_wrap {
 #define USB_STOR_TRANSPORT_GOOD	   0   /* Transport good, command good	   */
 #define USB_STOR_TRANSPORT_FAILED  1   /* Transport good, command failed   */
 #define USB_STOR_TRANSPORT_ERROR   2   /* Transport bad (i.e. device dead) */
-#define USB_STOR_TRANSPORT_ABORTED 3   /* Transport aborted                */
+
+/*
+ * We used to have USB_STOR_XFER_ABORTED and USB_STOR_TRANSPORT_ABORTED
+ * return codes.  But now the transport and low-level transfer routines
+ * treat an abort as just another error (-ENOENT for a cancelled URB).
+ * It is up to the invoke_transport() function to test for aborts and
+ * distinguish them from genuine communication errors.
+ */
 
 /*
  * CBI accept device specific command
@@ -162,12 +170,12 @@ extern int usb_stor_ctrl_transfer(struct us_data *us, unsigned int pipe,
 		u8 request, u8 requesttype, u16 value, u16 index,
 		void *data, u16 size);
 extern int usb_stor_bulk_transfer_buf(struct us_data *us, unsigned int pipe,
-		char *buf, unsigned int length, unsigned int *act_len);
+		void *buf, unsigned int length, unsigned int *act_len);
 extern int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
 		struct scatterlist *sg, int num_sg, unsigned int length,
 		unsigned int *act_len);
 extern int usb_stor_bulk_transfer_sg(struct us_data *us, unsigned int pipe,
-		char *buf, unsigned int length, int use_sg, int *residual);
+		void *buf, unsigned int length, int use_sg, int *residual);
 
 static __inline__ int usb_stor_bulk_transfer_srb(struct us_data *us,
 		unsigned int pipe, Scsi_Cmnd *srb, unsigned int length) {

include/linux/pci.h

@@ -517,21 +517,6 @@ void pcibios_update_resource(struct pci_dev *, struct resource *,
 void pcibios_update_irq(struct pci_dev *, int irq);
 void pcibios_fixup_pbus_ranges(struct pci_bus *, struct pbus_set_ranges_data *);
 
-/* Backward compatibility, don't use in new code! */
-
-int pcibios_read_config_byte (unsigned char bus, unsigned char dev_fn,
-			      unsigned char where, unsigned char *val);
-int pcibios_read_config_word (unsigned char bus, unsigned char dev_fn,
-			      unsigned char where, unsigned short *val);
-int pcibios_read_config_dword (unsigned char bus, unsigned char dev_fn,
-			       unsigned char where, unsigned int *val);
-int pcibios_write_config_byte (unsigned char bus, unsigned char dev_fn,
-			       unsigned char where, unsigned char val);
-int pcibios_write_config_word (unsigned char bus, unsigned char dev_fn,
-			       unsigned char where, unsigned short val);
-int pcibios_write_config_dword (unsigned char bus, unsigned char dev_fn,
-				unsigned char where, unsigned int val);
-
 /* Generic PCI functions used internally */
 
 int pci_bus_exists(const struct list_head *list, int nr);
@@ -668,8 +653,6 @@ extern struct pci_dev *isa_bridge;
 static inline int pci_present(void) { return 0; }
 
 #define _PCI_NOP(o,s,t) \
-	static inline int pcibios_##o##_config_##s (u8 bus, u8 dfn, u8 where, t val) \
-		{ return PCIBIOS_FUNC_NOT_SUPPORTED; } \
 	static inline int pci_##o##_config_##s (struct pci_dev *dev, int where, t val) \
 		{ return PCIBIOS_FUNC_NOT_SUPPORTED; }
 #define _PCI_NOP_ALL(o,x)	_PCI_NOP(o,byte,u8 x) \