Merge tag 'spi-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "A few core tweaks this time together with the usual collection of
  driver specific updates and fixes plus a larger than average selection
  of new device support:

   - fix DMA mapping of unaligned vmalloc() buffers

   - statistics tracking transfer volumes exposed via sysfs

   - new drivers for Freescale MPC5125, Intel Sunrise Point, Mediatek
     SoCs, and Netlogic XLP SoCs"

* tag 'spi-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (66 commits)
  spi: sh-msiof: Fix FIFO size to 64 word from 256 word
  spi: fsl-(e)spi: Fix checking return value of devm_ioremap_resource
  spi: Add DT bindings documentation for Netlogic XLP SPI controller
  spi/xlp: SPI controller driver for Netlogic XLP SoCs
  spi: fsl-espi: add runtime PM
  spi: fsl-(e)spi: simplify cleanup code
  spi: fsl-(e)spi: migrate to using devm_ functions to simplify cleanup
  spi: mediatek: fix SPI_CMD_PAUSE_IE macro error
  spi: check bits_per_word in spi_setup
  spi: mediatek: replace *_time name
  spi: mediatek: add PM clk_prepare_enable fail flow
  spi: mediatek: replace int with u32, delete TAB and define MTK_SPI_PAUSE_INT_STATUS marco
  spi: mediatek: add linux/io.h include file
  spi/bcm63xx-hsspi: add support for dual spi read/write
  spi: dw: Allow interface drivers to limit data I/O to word sizes
  dt: snps,dw-apb-ssi: Document new I/O data register width property
  spi: Fall back to master maximum speed if no slave speed specified
  spi: mediatek: use BIT() to instead of SPI_CMD_*_OFFSET
  spi: medaitek: revise quirks compatibility style
  spi: mediatek: fix spi incorrect endian usage
  ...

Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt

@@ -6,14 +6,14 @@ PSC in UART mode
 For PSC in UART mode the needed PSC serial devices
 are specified by fsl,mpc5121-psc-uart nodes in the
 fsl,mpc5121-immr SoC node. Additionally the PSC FIFO
-Controller node fsl,mpc5121-psc-fifo is requered there:
+Controller node fsl,mpc5121-psc-fifo is required there:
 
-fsl,mpc5121-psc-uart nodes
+fsl,mpc512x-psc-uart nodes
 --------------------------
 
 Required properties :
- - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc"
- - cell-index : Index of the PSC in hardware
+ - compatible : Should contain "fsl,<soc>-psc-uart" and "fsl,<soc>-psc"
+   Supported <soc>s: mpc5121, mpc5125
  - reg : Offset and length of the register set for the PSC device
  - interrupts : <a b> where a is the interrupt number of the
    PSC FIFO Controller and b is a field that represents an
@@ -25,12 +25,21 @@ Recommended properties :
  - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4)
  - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4)
 
+PSC in SPI mode
+---------------
 
-fsl,mpc5121-psc-fifo node
+Similar to the UART mode a PSC can be operated in SPI mode. The compatible used
+for that is fsl,mpc5121-psc-spi. It requires a fsl,mpc5121-psc-fifo as well.
+The required and recommended properties are identical to the
+fsl,mpc5121-psc-uart nodes, just use spi instead of uart in the compatible
+string.
+
+fsl,mpc512x-psc-fifo node
 -------------------------
 
 Required properties :
- - compatible : Should be "fsl,mpc5121-psc-fifo"
+ - compatible : Should be "fsl,<soc>-psc-fifo"
+   Supported <soc>s: mpc5121, mpc5125
  - reg : Offset and length of the register set for the PSC
          FIFO Controller
  - interrupts : <a b> where a is the interrupt number of the
@@ -39,6 +48,9 @@ Required properties :
  - interrupt-parent : the phandle for the interrupt controller that
    services interrupts for this device.
 
+Recommended properties :
+ - clocks : specifies the clock needed to operate the fifo controller
+ - clock-names : name(s) for the clock(s) listed in clocks
 
 Example for a board using PSC0 and PSC1 devices in serial mode:
 

Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt

@@ -10,6 +10,8 @@ Required properties:
 Optional properties:
 - cs-gpios : Specifies the gpio pis to be used for chipselects.
 - num-cs : The number of chipselects. If omitted, this will default to 4.
+- reg-io-width : The I/O register width (in bytes) implemented by this
+  device.  Supported values are 2 or 4 (the default).
 
 Child nodes as per the generic SPI binding.
 

Documentation/devicetree/bindings/spi/spi-davinci.txt

@@ -12,6 +12,8 @@ Required properties:
 - compatible:
 	- "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family
 	- "ti,da830-spi" for SPI used similar to that on DA8xx SoC family
+	- "ti,keystone-spi" for SPI used similar to that on Keystone2 SoC
+		family
 - reg: Offset and length of SPI controller register space
 - num-cs: Number of chip selects. This includes internal as well as
 	GPIO chip selects.

Documentation/devicetree/bindings/spi/spi-img-spfi.txt

@@ -21,6 +21,7 @@ Required properties:
 Optional properties:
 - img,supports-quad-mode: Should be set if the interface supports quad mode
   SPI transfers.
+- spfi-max-frequency: Maximum speed supported by the spfi block.
 
 Example:
 

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

+Binding for MTK SPI controller
+
+Required properties:
+- compatible: should be one of the following.
+    - mediatek,mt8173-spi: for mt8173 platforms
+    - mediatek,mt8135-spi: for mt8135 platforms
+    - mediatek,mt6589-spi: for mt6589 platforms
+
+- #address-cells: should be 1.
+
+- #size-cells: should be 0.
+
+- reg: Address and length of the register set for the device
+
+- interrupts: Should contain spi interrupt
+
+- clocks: phandles to input clocks.
+  The first should be <&topckgen CLK_TOP_SPI_SEL>.
+  The second should be one of the following.
+   -  <&clk26m>: specify parent clock 26MHZ.
+   -  <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ.
+				      It's the default one.
+   -  <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ.
+   -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
+   -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+
+- clock-names: shall be "spi-clk" for the controller clock, and
+  "parent-clk" for the parent clock.
+
+Optional properties:
+- mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
+  controller used, this value should be 0~3, only required for MT8173.
+    0: specify GPIO69,70,71,72 for spi pins.
+    1: specify GPIO102,103,104,105 for spi pins.
+    2: specify GPIO128,129,130,131 for spi pins.
+    3: specify GPIO5,6,7,8 for spi pins.
+
+Example:
+
+- SoC Specific Portion:
+spi: spi@1100a000 {
+	compatible = "mediatek,mt8173-spi";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0 0x1100a000 0 0x1000>;
+	interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>;
+	clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>;
+	clock-names = "spi-clk", "parent-clk";
+	mediatek,pad-select = <0>;
+	status = "disabled";
+};

Documentation/devicetree/bindings/spi/spi-xlp.txt

+SPI Master controller for Netlogic XLP MIPS64 SOCs
+==================================================
+
+Currently this SPI controller driver is supported for the following
+Netlogic XLP SoCs:
+	XLP832, XLP316, XLP208, XLP980, XLP532
+
+Required properties:
+- compatible		: Should be "netlogic,xlp832-spi".
+- #address-cells	: Number of cells required to define a chip select address
+			  on the SPI bus.
+- #size-cells		: Should be zero.
+- reg			: Should contain register location and length.
+- clocks		: Phandle of the spi clock
+- interrupts		: Interrupt number used by this controller.
+- interrupt-parent	: Phandle of the parent interrupt controller.
+
+SPI slave nodes must be children of the SPI master node and can contain
+properties described in Documentation/devicetree/bindings/spi/spi-bus.txt.
+
+Example:
+
+	spi: xlp_spi@3a100 {
+		compatible = "netlogic,xlp832-spi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0 0x3a100 0x100>;
+		clocks = <&spi_clk>;
+		interrupts = <34>;
+		interrupt-parent = <&pic>;
+
+		spi_nor@1 {
+			compatible = "spansion,s25sl12801";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <1>;	/* Chip Select */
+			spi-max-frequency = <40000000>;
+		};
+};

arch/arm/mach-davinci/devices-da8xx.c

@@ -1010,11 +1010,13 @@ static struct davinci_spi_platform_data da8xx_spi_pdata[] = {
 		.version	= SPI_VERSION_2,
 		.intr_line	= 1,
 		.dma_event_q	= EVENTQ_0,
+		.prescaler_limit = 2,
 	},
 	[1] = {
 		.version	= SPI_VERSION_2,
 		.intr_line	= 1,
 		.dma_event_q	= EVENTQ_0,
+		.prescaler_limit = 2,
 	},
 };
 

arch/arm/mach-davinci/dm355.c

@@ -411,6 +411,7 @@ static struct davinci_spi_platform_data dm355_spi0_pdata = {
 	.num_chipselect = 2,
 	.cshold_bug	= true,
 	.dma_event_q	= EVENTQ_1,
+	.prescaler_limit = 1,
 };
 static struct platform_device dm355_spi0_device = {
 	.name = "spi_davinci",

arch/arm/mach-davinci/dm365.c

@@ -646,6 +646,7 @@ static struct davinci_spi_platform_data dm365_spi0_pdata = {
 	.version 	= SPI_VERSION_1,
 	.num_chipselect = 2,
 	.dma_event_q	= EVENTQ_3,
+	.prescaler_limit = 1,
 };
 
 static struct resource dm365_spi0_resources[] = {

arch/powerpc/include/asm/mpc52xx_psc.h

@@ -150,7 +150,10 @@
 
 /* Structure of the hardware registers */
 struct mpc52xx_psc {
-	u8		mode;		/* PSC + 0x00 */
+	union {
+		u8	mode;		/* PSC + 0x00 */
+		u8	mr2;
+	};
 	u8		reserved0[3];
 	union {				/* PSC + 0x04 */
 		u16	status;

drivers/spi/Kconfig

@@ -326,6 +326,15 @@ config SPI_MESON_SPIFC
 	  This enables master mode support for the SPIFC (SPI flash
 	  controller) available in Amlogic Meson SoCs.
 
+config SPI_MT65XX
+	tristate "MediaTek SPI controller"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	help
+	  This selects the MediaTek(R) SPI bus driver.
+	  If you want to use MediaTek(R) SPI interface,
+	  say Y or M here.If you are not sure, say N.
+	  SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
+
 config SPI_OC_TINY
 	tristate "OpenCores tiny SPI"
 	depends on GPIOLIB || COMPILE_TEST
@@ -598,6 +607,17 @@ config SPI_XILINX
 
 	  Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 
+config SPI_XLP
+	tristate "Netlogic XLP SPI controller driver"
+	depends on CPU_XLP || COMPILE_TEST
+	help
+	  Enable support for the SPI controller on the Netlogic XLP SoCs.
+	  Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
+	  and XLP5XX.
+
+	  If you have a Netlogic XLP platform say Y here.
+	  If unsure, say N.
+
 config SPI_XTENSA_XTFPGA
 	tristate "Xtensa SPI controller for xtfpga"
 	depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST

drivers/spi/Makefile

@@ -48,6 +48,7 @@ obj-$(CONFIG_SPI_MESON_SPIFC)		+= spi-meson-spifc.o
 obj-$(CONFIG_SPI_MPC512x_PSC)		+= spi-mpc512x-psc.o
 obj-$(CONFIG_SPI_MPC52xx_PSC)		+= spi-mpc52xx-psc.o
 obj-$(CONFIG_SPI_MPC52xx)		+= spi-mpc52xx.o
+obj-$(CONFIG_SPI_MT65XX)                += spi-mt65xx.o
 obj-$(CONFIG_SPI_MXS)			+= spi-mxs.o
 obj-$(CONFIG_SPI_NUC900)		+= spi-nuc900.o
 obj-$(CONFIG_SPI_OC_TINY)		+= spi-oc-tiny.o
@@ -88,5 +89,6 @@ obj-$(CONFIG_SPI_TOPCLIFF_PCH)		+= spi-topcliff-pch.o
 obj-$(CONFIG_SPI_TXX9)			+= spi-txx9.o
 obj-$(CONFIG_SPI_XCOMM)		+= spi-xcomm.o
 obj-$(CONFIG_SPI_XILINX)		+= spi-xilinx.o
+obj-$(CONFIG_SPI_XLP)			+= spi-xlp.o
 obj-$(CONFIG_SPI_XTENSA_XTFPGA)		+= spi-xtensa-xtfpga.o
 obj-$(CONFIG_SPI_ZYNQMP_GQSPI)		+= spi-zynqmp-gqspi.o

drivers/spi/spi-atmel.c

@@ -19,7 +19,6 @@
 #include <linux/interrupt.h>
 #include <linux/spi/spi.h>
 #include <linux/slab.h>
-#include <linux/platform_data/atmel.h>
 #include <linux/platform_data/dma-atmel.h>
 #include <linux/of.h>
 

drivers/spi/spi-bcm2835.c

@@ -480,7 +480,7 @@ static int bcm2835_spi_transfer_one_poll(struct spi_master *master,
 					 struct spi_device *spi,
 					 struct spi_transfer *tfr,
 					 u32 cs,
-					 unsigned long xfer_time_us)
+					 unsigned long long xfer_time_us)
 {
 	struct bcm2835_spi *bs = spi_master_get_devdata(master);
 	unsigned long timeout;
@@ -531,7 +531,8 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
 {
 	struct bcm2835_spi *bs = spi_master_get_devdata(master);
 	unsigned long spi_hz, clk_hz, cdiv;
-	unsigned long spi_used_hz, xfer_time_us;
+	unsigned long spi_used_hz;
+	unsigned long long xfer_time_us;
 	u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
 
 	/* set clock */
@@ -553,13 +554,11 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
 	spi_used_hz = cdiv ? (clk_hz / cdiv) : (clk_hz / 65536);
 	bcm2835_wr(bs, BCM2835_SPI_CLK, cdiv);
 
-	/* handle all the modes */
+	/* handle all the 3-wire mode */
 	if ((spi->mode & SPI_3WIRE) && (tfr->rx_buf))
 		cs |= BCM2835_SPI_CS_REN;
-	if (spi->mode & SPI_CPOL)
-		cs |= BCM2835_SPI_CS_CPOL;
-	if (spi->mode & SPI_CPHA)
-		cs |= BCM2835_SPI_CS_CPHA;
+	else
+		cs &= ~BCM2835_SPI_CS_REN;
 
 	/* for gpio_cs set dummy CS so that no HW-CS get changed
 	 * we can not run this in bcm2835_spi_set_cs, as it does
@@ -575,9 +574,10 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
 	bs->rx_len = tfr->len;
 
 	/* calculate the estimated time in us the transfer runs */
-	xfer_time_us = tfr->len
+	xfer_time_us = (unsigned long long)tfr->len
 		* 9 /* clocks/byte - SPI-HW waits 1 clock after each byte */
-		* 1000000 / spi_used_hz;
+		* 1000000;
+	do_div(xfer_time_us, spi_used_hz);
 
 	/* for short requests run polling*/
 	if (xfer_time_us <= BCM2835_SPI_POLLING_LIMIT_US)
@@ -592,6 +592,25 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
 	return bcm2835_spi_transfer_one_irq(master, spi, tfr, cs);
 }
 
+static int bcm2835_spi_prepare_message(struct spi_master *master,
+				       struct spi_message *msg)
+{
+	struct spi_device *spi = msg->spi;
+	struct bcm2835_spi *bs = spi_master_get_devdata(master);
+	u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+
+	cs &= ~(BCM2835_SPI_CS_CPOL | BCM2835_SPI_CS_CPHA);
+
+	if (spi->mode & SPI_CPOL)
+		cs |= BCM2835_SPI_CS_CPOL;
+	if (spi->mode & SPI_CPHA)
+		cs |= BCM2835_SPI_CS_CPHA;
+
+	bcm2835_wr(bs, BCM2835_SPI_CS, cs);
+
+	return 0;
+}
+
 static void bcm2835_spi_handle_err(struct spi_master *master,
 				   struct spi_message *msg)
 {
@@ -739,6 +758,7 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 	master->set_cs = bcm2835_spi_set_cs;
 	master->transfer_one = bcm2835_spi_transfer_one;
 	master->handle_err = bcm2835_spi_handle_err;
+	master->prepare_message = bcm2835_spi_prepare_message;
 	master->dev.of_node = pdev->dev.of_node;
 
 	bs = spi_master_get_devdata(master);

drivers/spi/spi-bcm63xx-hsspi.c

@@ -76,6 +76,7 @@
 #define HSSPI_FIFO_REG(x)			(0x200 + (x) * 0x200)
 
 
+#define HSSPI_OP_MULTIBIT			BIT(11)
 #define HSSPI_OP_CODE_SHIFT			13
 #define HSSPI_OP_SLEEP				(0 << HSSPI_OP_CODE_SHIFT)
 #define HSSPI_OP_READ_WRITE			(1 << HSSPI_OP_CODE_SHIFT)
@@ -171,9 +172,12 @@ static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t)
 	if (opcode != HSSPI_OP_READ)
 		step_size -= HSSPI_OPCODE_LEN;
 
-	__raw_writel(0 << MODE_CTRL_PREPENDBYTE_CNT_SHIFT |
-		     2 << MODE_CTRL_MULTIDATA_WR_STRT_SHIFT |
-		     2 << MODE_CTRL_MULTIDATA_RD_STRT_SHIFT | 0xff,
+	if ((opcode == HSSPI_OP_READ && t->rx_nbits == SPI_NBITS_DUAL) ||
+	    (opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL))
+		opcode |= HSSPI_OP_MULTIBIT;
+
+	__raw_writel(1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT |
+		     1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT | 0xff,
 		     bs->regs + HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
 
 	while (pending > 0) {
@@ -374,7 +378,8 @@ static int bcm63xx_hsspi_probe(struct platform_device *pdev)
 	master->num_chipselect = 8;
 	master->setup = bcm63xx_hsspi_setup;
 	master->transfer_one_message = bcm63xx_hsspi_transfer_one;
-	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH |
+			    SPI_RX_DUAL | SPI_TX_DUAL;
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
 	master->auto_runtime_pm = true;
 

drivers/spi/spi-bitbang-txrx.h

@@ -49,7 +49,7 @@ bitbang_txrx_be_cpha0(struct spi_device *spi,
 {
 	/* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */
 
-	bool oldbit = !(word & 1);
+	u32 oldbit = (!(word & (1<<(bits-1)))) << 31;
 	/* clock starts at inactive polarity */
 	for (word <<= (32 - bits); likely(bits); bits--) {
 
@@ -81,7 +81,7 @@ bitbang_txrx_be_cpha1(struct spi_device *spi,
 {
 	/* if (cpol == 0) this is SPI_MODE_1; else this is SPI_MODE_3 */
 
-	bool oldbit = !(word & (1 << 31));
+	u32 oldbit = (!(word & (1<<(bits-1)))) << 31;
 	/* clock starts at inactive polarity */
 	for (word <<= (32 - bits); likely(bits); bits--) {
 

drivers/spi/spi-davinci.c

@@ -139,6 +139,8 @@ struct davinci_spi {
 	u32			(*get_tx)(struct davinci_spi *);
 
 	u8			*bytes_per_word;
+
+	u8			prescaler_limit;
 };
 
 static struct davinci_spi_config davinci_spi_default_cfg;
@@ -255,7 +257,7 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value)
  * This function calculates the prescale value that generates a clock rate
  * less than or equal to the specified maximum.
  *
- * Returns: calculated prescale - 1 for easy programming into SPI registers
+ * Returns: calculated prescale value for easy programming into SPI registers
  * or negative error number if valid prescalar cannot be updated.
  */
 static inline int davinci_spi_get_prescale(struct davinci_spi *dspi,
@@ -263,12 +265,13 @@ static inline int davinci_spi_get_prescale(struct davinci_spi *dspi,
 {
 	int ret;
 
-	ret = DIV_ROUND_UP(clk_get_rate(dspi->clk), max_speed_hz);
+	/* Subtract 1 to match what will be programmed into SPI register. */
+	ret = DIV_ROUND_UP(clk_get_rate(dspi->clk), max_speed_hz) - 1;
 
-	if (ret < 1 || ret > 256)
+	if (ret < dspi->prescaler_limit || ret > 255)
 		return -EINVAL;
 
-	return ret - 1;
+	return ret;
 }
 
 /**
@@ -832,13 +835,40 @@ static int davinci_spi_request_dma(struct davinci_spi *dspi)
 }
 
 #if defined(CONFIG_OF)
+
+/* OF SPI data structure */
+struct davinci_spi_of_data {
+	u8	version;
+	u8	prescaler_limit;
+};
+
+static const struct davinci_spi_of_data dm6441_spi_data = {
+	.version = SPI_VERSION_1,
+	.prescaler_limit = 2,
+};
+
+static const struct davinci_spi_of_data da830_spi_data = {
+	.version = SPI_VERSION_2,
+	.prescaler_limit = 2,
+};
+
+static const struct davinci_spi_of_data keystone_spi_data = {
+	.version = SPI_VERSION_1,
+	.prescaler_limit = 0,
+};
+
 static const struct of_device_id davinci_spi_of_match[] = {
 	{
 		.compatible = "ti,dm6441-spi",
+		.data = &dm6441_spi_data,
 	},
 	{
 		.compatible = "ti,da830-spi",
-		.data = (void *)SPI_VERSION_2,
+		.data = &da830_spi_data,
+	},
+	{
+		.compatible = "ti,keystone-spi",
+		.data = &keystone_spi_data,
 	},
 	{ },
 };
@@ -857,21 +887,21 @@ static int spi_davinci_get_pdata(struct platform_device *pdev,
 			struct davinci_spi *dspi)
 {
 	struct device_node *node = pdev->dev.of_node;
+	struct davinci_spi_of_data *spi_data;
 	struct davinci_spi_platform_data *pdata;
 	unsigned int num_cs, intr_line = 0;
 	const struct of_device_id *match;
 
 	pdata = &dspi->pdata;
 
-	pdata->version = SPI_VERSION_1;
 	match = of_match_device(davinci_spi_of_match, &pdev->dev);
 	if (!match)
 		return -ENODEV;
 
-	/* match data has the SPI version number for SPI_VERSION_2 */
-	if (match->data == (void *)SPI_VERSION_2)
-		pdata->version = SPI_VERSION_2;
+	spi_data = (struct davinci_spi_of_data *)match->data;
 
+	pdata->version = spi_data->version;
+	pdata->prescaler_limit = spi_data->prescaler_limit;
 	/*
 	 * default num_cs is 1 and all chipsel are internal to the chip
 	 * indicated by chip_sel being NULL or cs_gpios being NULL or
@@ -991,7 +1021,7 @@ static int davinci_spi_probe(struct platform_device *pdev)
 
 	dspi->bitbang.chipselect = davinci_spi_chipselect;
 	dspi->bitbang.setup_transfer = davinci_spi_setup_transfer;
-
+	dspi->prescaler_limit = pdata->prescaler_limit;
 	dspi->version = pdata->version;
 
 	dspi->bitbang.flags = SPI_NO_CS | SPI_LSB_FIRST | SPI_LOOP;

drivers/spi/spi-dw-mmio.c

@@ -74,6 +74,9 @@ static int dw_spi_mmio_probe(struct platform_device *pdev)
 
 	dws->max_freq = clk_get_rate(dwsmmio->clk);
 
+	of_property_read_u32(pdev->dev.of_node, "reg-io-width",
+			     &dws->reg_io_width);
+
 	num_cs = 4;
 
 	if (pdev->dev.of_node)

drivers/spi/spi-dw.c

@@ -194,7 +194,7 @@ static void dw_writer(struct dw_spi *dws)
 			else
 				txw = *(u16 *)(dws->tx);
 		}
-		dw_writel(dws, DW_SPI_DR, txw);
+		dw_write_io_reg(dws, DW_SPI_DR, txw);
 		dws->tx += dws->n_bytes;
 	}
 }
@@ -205,7 +205,7 @@ static void dw_reader(struct dw_spi *dws)
 	u16 rxw;
 
 	while (max--) {
-		rxw = dw_readl(dws, DW_SPI_DR);
+		rxw = dw_read_io_reg(dws, DW_SPI_DR);
 		/* Care rx only if the transfer's original "rx" is not null */
 		if (dws->rx_end - dws->len) {
 			if (dws->n_bytes == 1)

drivers/spi/spi-dw.h

@@ -109,6 +109,7 @@ struct dw_spi {
 	u32			fifo_len;	/* depth of the FIFO buffer */
 	u32			max_freq;	/* max bus freq supported */
 
+	u32			reg_io_width;	/* DR I/O width in bytes */
 	u16			bus_num;
 	u16			num_cs;		/* supported slave numbers */
 
@@ -145,11 +146,45 @@ static inline u32 dw_readl(struct dw_spi *dws, u32 offset)
 	return __raw_readl(dws->regs + offset);
 }
 
+static inline u16 dw_readw(struct dw_spi *dws, u32 offset)
+{
+	return __raw_readw(dws->regs + offset);
+}
+
 static inline void dw_writel(struct dw_spi *dws, u32 offset, u32 val)
 {
 	__raw_writel(val, dws->regs + offset);
 }
 
+static inline void dw_writew(struct dw_spi *dws, u32 offset, u16 val)
+{
+	__raw_writew(val, dws->regs + offset);
+}
+
+static inline u32 dw_read_io_reg(struct dw_spi *dws, u32 offset)
+{
+	switch (dws->reg_io_width) {
+	case 2:
+		return dw_readw(dws, offset);
+	case 4:
+	default:
+		return dw_readl(dws, offset);
+	}
+}
+
+static inline void dw_write_io_reg(struct dw_spi *dws, u32 offset, u32 val)
+{
+	switch (dws->reg_io_width) {
+	case 2:
+		dw_writew(dws, offset, val);
+		break;
+	case 4:
+	default:
+		dw_writel(dws, offset, val);
+		break;
+	}
+}
+
 static inline void spi_enable_chip(struct dw_spi *dws, int enable)
 {
 	dw_writel(dws, DW_SPI_SSIENR, (enable ? 1 : 0));

drivers/spi/spi-fsl-espi.c

@@ -21,6 +21,7 @@
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
+#include <linux/pm_runtime.h>
 #include <sysdev/fsl_soc.h>
 
 #include "spi-fsl-lib.h"
@@ -85,6 +86,8 @@ struct fsl_espi_transfer {
 #define SPCOM_TRANLEN(x)	((x) << 0)
 #define	SPCOM_TRANLEN_MAX	0xFFFF	/* Max transaction length */
 
+#define AUTOSUSPEND_TIMEOUT 2000
+
 static void fsl_espi_change_mode(struct spi_device *spi)
 {
 	struct mpc8xxx_spi *mspi = spi_master_get_devdata(spi->master);
@@ -485,6 +488,8 @@ static int fsl_espi_setup(struct spi_device *spi)
 	mpc8xxx_spi = spi_master_get_devdata(spi->master);
 	reg_base = mpc8xxx_spi->reg_base;
 
+	pm_runtime_get_sync(mpc8xxx_spi->dev);
+
 	hw_mode = cs->hw_mode; /* Save original settings */
 	cs->hw_mode = mpc8xxx_spi_read_reg(
 			&reg_base->csmode[spi->chip_select]);
@@ -507,6 +512,10 @@ static int fsl_espi_setup(struct spi_device *spi)
 	mpc8xxx_spi_write_reg(&reg_base->mode, loop_mode);
 
 	retval = fsl_espi_setup_transfer(spi, NULL);
+
+	pm_runtime_mark_last_busy(mpc8xxx_spi->dev);
+	pm_runtime_put_autosuspend(mpc8xxx_spi->dev);
+
 	if (retval < 0) {
 		cs->hw_mode = hw_mode; /* Restore settings */
 		return retval;
@@ -604,20 +613,14 @@ static irqreturn_t fsl_espi_irq(s32 irq, void *context_data)
 	return ret;
 }
 
-static void fsl_espi_remove(struct mpc8xxx_spi *mspi)
+#ifdef CONFIG_PM
+static int fsl_espi_runtime_suspend(struct device *dev)
 {
-	iounmap(mspi->reg_base);
-}
-
-static int fsl_espi_suspend(struct spi_master *master)
-{
-	struct mpc8xxx_spi *mpc8xxx_spi;
-	struct fsl_espi_reg *reg_base;
+	struct spi_master *master = dev_get_drvdata(dev);
+	struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(master);
+	struct fsl_espi_reg *reg_base = mpc8xxx_spi->reg_base;
 	u32 regval;
 
-	mpc8xxx_spi = spi_master_get_devdata(master);
-	reg_base = mpc8xxx_spi->reg_base;
-
 	regval = mpc8xxx_spi_read_reg(&reg_base->mode);
 	regval &= ~SPMODE_ENABLE;
 	mpc8xxx_spi_write_reg(&reg_base->mode, regval);
@@ -625,21 +628,20 @@ static int fsl_espi_suspend(struct spi_master *master)
 	return 0;
 }
 
-static int fsl_espi_resume(struct spi_master *master)
+static int fsl_espi_runtime_resume(struct device *dev)
 {
-	struct mpc8xxx_spi *mpc8xxx_spi;
-	struct fsl_espi_reg *reg_base;
+	struct spi_master *master = dev_get_drvdata(dev);
+	struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(master);
+	struct fsl_espi_reg *reg_base = mpc8xxx_spi->reg_base;
 	u32 regval;
 
-	mpc8xxx_spi = spi_master_get_devdata(master);
-	reg_base = mpc8xxx_spi->reg_base;
-
 	regval = mpc8xxx_spi_read_reg(&reg_base->mode);
 	regval |= SPMODE_ENABLE;
 	mpc8xxx_spi_write_reg(&reg_base->mode, regval);
 
 	return 0;
 }
+#endif
 
 static struct spi_master * fsl_espi_probe(struct device *dev,
 		struct resource *mem, unsigned int irq)
@@ -667,25 +669,23 @@ static struct spi_master * fsl_espi_probe(struct device *dev,
 	master->setup = fsl_espi_setup;
 	master->cleanup = fsl_espi_cleanup;
 	master->transfer_one_message = fsl_espi_do_one_msg;
-	master->prepare_transfer_hardware = fsl_espi_resume;
-	master->unprepare_transfer_hardware = fsl_espi_suspend;
+	master->auto_runtime_pm = true;
 
 	mpc8xxx_spi = spi_master_get_devdata(master);
-	mpc8xxx_spi->spi_remove = fsl_espi_remove;
 
-	mpc8xxx_spi->reg_base = ioremap(mem->start, resource_size(mem));
-	if (!mpc8xxx_spi->reg_base) {
-		ret = -ENOMEM;
+	mpc8xxx_spi->reg_base = devm_ioremap_resource(dev, mem);
+	if (IS_ERR(mpc8xxx_spi->reg_base)) {
+		ret = PTR_ERR(mpc8xxx_spi->reg_base);
 		goto err_probe;
 	}
 
 	reg_base = mpc8xxx_spi->reg_base;
 
 	/* Register for SPI Interrupt */
-	ret = request_irq(mpc8xxx_spi->irq, fsl_espi_irq,
+	ret = devm_request_irq(dev, mpc8xxx_spi->irq, fsl_espi_irq,
 			  0, "fsl_espi", mpc8xxx_spi);
 	if (ret)
-		goto free_irq;
+		goto err_probe;
 
 	if (mpc8xxx_spi->flags & SPI_QE_CPU_MODE) {
 		mpc8xxx_spi->rx_shift = 16;
@@ -731,18 +731,27 @@ static struct spi_master * fsl_espi_probe(struct device *dev,
 
 	mpc8xxx_spi_write_reg(&reg_base->mode, regval);
 
-	ret = spi_register_master(master);
+	pm_runtime_set_autosuspend_delay(dev, AUTOSUSPEND_TIMEOUT);
+	pm_runtime_use_autosuspend(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+
+	ret = devm_spi_register_master(dev, master);
 	if (ret < 0)
-		goto unreg_master;
+		goto err_pm;
 
 	dev_info(dev, "at 0x%p (irq = %d)\n", reg_base, mpc8xxx_spi->irq);
 
+	pm_runtime_mark_last_busy(dev);
+	pm_runtime_put_autosuspend(dev);
+
 	return master;
 
-unreg_master:
-	free_irq(mpc8xxx_spi->irq, mpc8xxx_spi);
-free_irq:
-	iounmap(mpc8xxx_spi->reg_base);
+err_pm:
+	pm_runtime_put_noidle(dev);
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
 err_probe:
 	spi_master_put(master);
 err:
@@ -809,7 +818,9 @@ static int of_fsl_espi_probe(struct platform_device *ofdev)
 
 static int of_fsl_espi_remove(struct platform_device *dev)
 {
-	return mpc8xxx_spi_remove(&dev->dev);
+	pm_runtime_disable(&dev->dev);
+
+	return 0;
 }
 
 #ifdef CONFIG_PM_SLEEP
@@ -824,7 +835,11 @@ static int of_fsl_espi_suspend(struct device *dev)
 		return ret;
 	}
 
-	return fsl_espi_suspend(master);
+	ret = pm_runtime_force_suspend(dev);
+	if (ret < 0)
+		return ret;
+
+	return 0;
 }
 
 static int of_fsl_espi_resume(struct device *dev)
@@ -834,7 +849,7 @@ static int of_fsl_espi_resume(struct device *dev)
 	struct mpc8xxx_spi *mpc8xxx_spi;
 	struct fsl_espi_reg *reg_base;
 	u32 regval;
-	int i;
+	int i, ret;
 
 	mpc8xxx_spi = spi_master_get_devdata(master);
 	reg_base = mpc8xxx_spi->reg_base;
@@ -854,11 +869,17 @@ static int of_fsl_espi_resume(struct device *dev)
 
 	mpc8xxx_spi_write_reg(&reg_base->mode, regval);
 
+	ret = pm_runtime_force_resume(dev);
+	if (ret < 0)
+		return ret;
+
 	return spi_master_resume(master);
 }
 #endif /* CONFIG_PM_SLEEP */
 
 static const struct dev_pm_ops espi_pm = {
+	SET_RUNTIME_PM_OPS(fsl_espi_runtime_suspend,
+			   fsl_espi_runtime_resume, NULL)
 	SET_SYSTEM_SLEEP_PM_OPS(of_fsl_espi_suspend, of_fsl_espi_resume)
 };
 

drivers/spi/spi-fsl-lib.c

@@ -114,25 +114,6 @@ void mpc8xxx_spi_probe(struct device *dev, struct resource *mem,
 }
 EXPORT_SYMBOL_GPL(mpc8xxx_spi_probe);
 
-int mpc8xxx_spi_remove(struct device *dev)
-{
-	struct mpc8xxx_spi *mpc8xxx_spi;
-	struct spi_master *master;
-
-	master = dev_get_drvdata(dev);
-	mpc8xxx_spi = spi_master_get_devdata(master);
-
-	spi_unregister_master(master);
-
-	free_irq(mpc8xxx_spi->irq, mpc8xxx_spi);
-
-	if (mpc8xxx_spi->spi_remove)
-		mpc8xxx_spi->spi_remove(mpc8xxx_spi);
-
-	return 0;
-}
-EXPORT_SYMBOL_GPL(mpc8xxx_spi_remove);
-
 int of_mpc8xxx_spi_probe(struct platform_device *ofdev)
 {
 	struct device *dev = &ofdev->dev;

drivers/spi/spi-fsl-lib.h

@@ -54,9 +54,6 @@ struct mpc8xxx_spi {
 	void (*get_rx) (u32 rx_data, struct mpc8xxx_spi *);
 	u32(*get_tx) (struct mpc8xxx_spi *);
 
-	/* hooks for different controller driver */
-	void (*spi_remove) (struct mpc8xxx_spi *mspi);
-
 	unsigned int count;
 	unsigned int irq;
 

drivers/spi/spi-fsl-spi.c

@@ -559,12 +559,6 @@ static irqreturn_t fsl_spi_irq(s32 irq, void *context_data)
 	return ret;
 }
 
-static void fsl_spi_remove(struct mpc8xxx_spi *mspi)
-{
-	iounmap(mspi->reg_base);
-	fsl_spi_cpm_free(mspi);
-}
-
 static void fsl_spi_grlib_cs_control(struct spi_device *spi, bool on)
 {
 	struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(spi->master);
@@ -631,7 +625,6 @@ static struct spi_master * fsl_spi_probe(struct device *dev,
 	master->transfer_one_message = fsl_spi_do_one_msg;
 
 	mpc8xxx_spi = spi_master_get_devdata(master);
-	mpc8xxx_spi->spi_remove = fsl_spi_remove;
 	mpc8xxx_spi->max_bits_per_word = 32;
 	mpc8xxx_spi->type = fsl_spi_get_type(dev);
 
@@ -639,10 +632,10 @@ static struct spi_master * fsl_spi_probe(struct device *dev,
 	if (ret)
 		goto err_cpm_init;
 
-	mpc8xxx_spi->reg_base = ioremap(mem->start, resource_size(mem));
-	if (mpc8xxx_spi->reg_base == NULL) {
-		ret = -ENOMEM;
-		goto err_ioremap;
+	mpc8xxx_spi->reg_base = devm_ioremap_resource(dev, mem);
+	if (IS_ERR(mpc8xxx_spi->reg_base)) {
+		ret = PTR_ERR(mpc8xxx_spi->reg_base);
+		goto err_probe;
 	}
 
 	if (mpc8xxx_spi->type == TYPE_GRLIB)
@@ -661,11 +654,11 @@ static struct spi_master * fsl_spi_probe(struct device *dev,
 					&mpc8xxx_spi->tx_shift, 8, 1);
 
 	/* Register for SPI Interrupt */
-	ret = request_irq(mpc8xxx_spi->irq, fsl_spi_irq,
-			  0, "fsl_spi", mpc8xxx_spi);
+	ret = devm_request_irq(dev, mpc8xxx_spi->irq, fsl_spi_irq,
+			       0, "fsl_spi", mpc8xxx_spi);
 
 	if (ret != 0)
-		goto free_irq;
+		goto err_probe;
 
 	reg_base = mpc8xxx_spi->reg_base;
 
@@ -686,20 +679,16 @@ static struct spi_master * fsl_spi_probe(struct device *dev,
 
 	mpc8xxx_spi_write_reg(&reg_base->mode, regval);
 
-	ret = spi_register_master(master);
+	ret = devm_spi_register_master(dev, master);
 	if (ret < 0)
-		goto unreg_master;
+		goto err_probe;
 
 	dev_info(dev, "at 0x%p (irq = %d), %s mode\n", reg_base,
 		 mpc8xxx_spi->irq, mpc8xxx_spi_strmode(mpc8xxx_spi->flags));
 
 	return master;
 
-unreg_master:
-	free_irq(mpc8xxx_spi->irq, mpc8xxx_spi);
-free_irq:
-	iounmap(mpc8xxx_spi->reg_base);
-err_ioremap:
+err_probe:
 	fsl_spi_cpm_free(mpc8xxx_spi);
 err_cpm_init:
 	spi_master_put(master);
@@ -866,11 +855,8 @@ static int of_fsl_spi_remove(struct platform_device *ofdev)
 {
 	struct spi_master *master = platform_get_drvdata(ofdev);
 	struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(master);
-	int ret;
 
-	ret = mpc8xxx_spi_remove(&ofdev->dev);
-	if (ret)
-		return ret;
+	fsl_spi_cpm_free(mpc8xxx_spi);
 	if (mpc8xxx_spi->type == TYPE_FSL)
 		of_fsl_spi_free_chipselects(&ofdev->dev);
 	return 0;
@@ -916,7 +902,12 @@ static int plat_mpc8xxx_spi_probe(struct platform_device *pdev)
 
 static int plat_mpc8xxx_spi_remove(struct platform_device *pdev)
 {
-	return mpc8xxx_spi_remove(&pdev->dev);
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(master);
+
+	fsl_spi_cpm_free(mpc8xxx_spi);
+
+	return 0;
 }
 
 MODULE_ALIAS("platform:mpc8xxx_spi");

drivers/spi/spi-img-spfi.c

@@ -105,6 +105,10 @@ struct img_spfi {
 	bool rx_dma_busy;
 };
 
+struct img_spfi_device_data {
+	bool gpio_requested;
+};
+
 static inline u32 spfi_readl(struct img_spfi *spfi, u32 reg)
 {
 	return readl(spfi->regs + reg);
@@ -267,15 +271,15 @@ static int img_spfi_start_pio(struct spi_master *master,
 		cpu_relax();
 	}
 
-	ret = spfi_wait_all_done(spfi);
-	if (ret < 0)
-		return ret;
-
 	if (rx_bytes > 0 || tx_bytes > 0) {
 		dev_err(spfi->dev, "PIO transfer timed out\n");
 		return -ETIMEDOUT;
 	}
 
+	ret = spfi_wait_all_done(spfi);
+	if (ret < 0)
+		return ret;
+
 	return 0;
 }
 
@@ -440,21 +444,50 @@ static int img_spfi_unprepare(struct spi_master *master,
 
 static int img_spfi_setup(struct spi_device *spi)
 {
-	int ret;
-
-	ret = gpio_request_one(spi->cs_gpio, (spi->mode & SPI_CS_HIGH) ?
-			       GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH,
-			       dev_name(&spi->dev));
-	if (ret)
-		dev_err(&spi->dev, "can't request chipselect gpio %d\n",
+	int ret = -EINVAL;
+	struct img_spfi_device_data *spfi_data = spi_get_ctldata(spi);
+
+	if (!spfi_data) {
+		spfi_data = kzalloc(sizeof(*spfi_data), GFP_KERNEL);
+		if (!spfi_data)
+			return -ENOMEM;
+		spfi_data->gpio_requested = false;
+		spi_set_ctldata(spi, spfi_data);
+	}
+	if (!spfi_data->gpio_requested) {
+		ret = gpio_request_one(spi->cs_gpio,
+				       (spi->mode & SPI_CS_HIGH) ?
+				       GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH,
+				       dev_name(&spi->dev));
+		if (ret)
+			dev_err(&spi->dev, "can't request chipselect gpio %d\n",
 				spi->cs_gpio);
-
+		else
+			spfi_data->gpio_requested = true;
+	} else {
+		if (gpio_is_valid(spi->cs_gpio)) {
+			int mode = ((spi->mode & SPI_CS_HIGH) ?
+				    GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH);
+
+			ret = gpio_direction_output(spi->cs_gpio, mode);
+			if (ret)
+				dev_err(&spi->dev, "chipselect gpio %d setup failed (%d)\n",
+					spi->cs_gpio, ret);
+		}
+	}
 	return ret;
 }
 
 static void img_spfi_cleanup(struct spi_device *spi)
 {
-	gpio_free(spi->cs_gpio);
+	struct img_spfi_device_data *spfi_data = spi_get_ctldata(spi);
+
+	if (spfi_data) {
+		if (spfi_data->gpio_requested)
+			gpio_free(spi->cs_gpio);
+		kfree(spfi_data);
+		spi_set_ctldata(spi, NULL);
+	}
 }
 
 static void img_spfi_config(struct spi_master *master, struct spi_device *spi,
@@ -548,6 +581,7 @@ static int img_spfi_probe(struct platform_device *pdev)
 	struct img_spfi *spfi;
 	struct resource *res;
 	int ret;
+	u32 max_speed_hz;
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*spfi));
 	if (!master)
@@ -612,6 +646,19 @@ static int img_spfi_probe(struct platform_device *pdev)
 	master->max_speed_hz = clk_get_rate(spfi->spfi_clk) / 4;
 	master->min_speed_hz = clk_get_rate(spfi->spfi_clk) / 512;
 
+	/*
+	 * Maximum speed supported by spfi is limited to the lower value
+	 * between 1/4 of the SPFI clock or to "spfi-max-frequency"
+	 * defined in the device tree.
+	 * If no value is defined in the device tree assume the maximum
+	 * speed supported to be 1/4 of the SPFI clock.
+	 */
+	if (!of_property_read_u32(spfi->dev->of_node, "spfi-max-frequency",
+				  &max_speed_hz)) {
+		if (master->max_speed_hz > max_speed_hz)
+			master->max_speed_hz = max_speed_hz;
+	}
+
 	master->setup = img_spfi_setup;
 	master->cleanup = img_spfi_cleanup;
 	master->transfer_one = img_spfi_transfer_one;

drivers/spi/spi-mpc512x-psc.c

@@ -30,11 +30,37 @@
 #include <linux/gpio.h>
 #include <asm/mpc52xx_psc.h>
 
+enum {
+	TYPE_MPC5121,
+	TYPE_MPC5125,
+};
+
+/*
+ * This macro abstracts the differences in the PSC register layout between
+ * MPC5121 (which uses a struct mpc52xx_psc) and MPC5125 (using mpc5125_psc).
+ */
+#define psc_addr(mps, regname) ({					\
+	void *__ret = NULL;						\
+	switch (mps->type) {						\
+	case TYPE_MPC5121: {						\
+			struct mpc52xx_psc __iomem *psc = mps->psc;	\
+			__ret = &psc->regname;				\
+		};							\
+		break;							\
+	case TYPE_MPC5125: {						\
+			struct mpc5125_psc __iomem *psc = mps->psc;	\
+			__ret = &psc->regname;				\
+		};							\
+		break;							\
+	}								\
+	__ret; })
+
 struct mpc512x_psc_spi {
 	void (*cs_control)(struct spi_device *spi, bool on);
 
 	/* driver internal data */
-	struct mpc52xx_psc __iomem *psc;
+	int type;
+	void __iomem *psc;
 	struct mpc512x_psc_fifo __iomem *fifo;
 	unsigned int irq;
 	u8 bits_per_word;
@@ -71,13 +97,12 @@ static void mpc512x_psc_spi_activate_cs(struct spi_device *spi)
 {
 	struct mpc512x_psc_spi_cs *cs = spi->controller_state;
 	struct mpc512x_psc_spi *mps = spi_master_get_devdata(spi->master);
-	struct mpc52xx_psc __iomem *psc = mps->psc;
 	u32 sicr;
 	u32 ccr;
 	int speed;
 	u16 bclkdiv;
 
-	sicr = in_be32(&psc->sicr);
+	sicr = in_be32(psc_addr(mps, sicr));
 
 	/* Set clock phase and polarity */
 	if (spi->mode & SPI_CPHA)
@@ -94,9 +119,9 @@ static void mpc512x_psc_spi_activate_cs(struct spi_device *spi)
 		sicr |= 0x10000000;
 	else
 		sicr &= ~0x10000000;
-	out_be32(&psc->sicr, sicr);
+	out_be32(psc_addr(mps, sicr), sicr);
 
-	ccr = in_be32(&psc->ccr);
+	ccr = in_be32(psc_addr(mps, ccr));
 	ccr &= 0xFF000000;
 	speed = cs->speed_hz;
 	if (!speed)
@@ -104,7 +129,7 @@ static void mpc512x_psc_spi_activate_cs(struct spi_device *spi)
 	bclkdiv = (mps->mclk_rate / speed) - 1;
 
 	ccr |= (((bclkdiv & 0xff) << 16) | (((bclkdiv >> 8) & 0xff) << 8));
-	out_be32(&psc->ccr, ccr);
+	out_be32(psc_addr(mps, ccr), ccr);
 	mps->bits_per_word = cs->bits_per_word;
 
 	if (mps->cs_control && gpio_is_valid(spi->cs_gpio))
@@ -315,16 +340,15 @@ static int mpc512x_psc_spi_msg_xfer(struct spi_master *master,
 static int mpc512x_psc_spi_prep_xfer_hw(struct spi_master *master)
 {
 	struct mpc512x_psc_spi *mps = spi_master_get_devdata(master);
-	struct mpc52xx_psc __iomem *psc = mps->psc;
 
 	dev_dbg(&master->dev, "%s()\n", __func__);
 
 	/* Zero MR2 */
-	in_8(&psc->mode);
-	out_8(&psc->mode, 0x0);
+	in_8(psc_addr(mps, mr2));
+	out_8(psc_addr(mps, mr2), 0x0);
 
 	/* enable transmitter/receiver */
-	out_8(&psc->command, MPC52xx_PSC_TX_ENABLE | MPC52xx_PSC_RX_ENABLE);
+	out_8(psc_addr(mps, command), MPC52xx_PSC_TX_ENABLE | MPC52xx_PSC_RX_ENABLE);
 
 	return 0;
 }
@@ -332,13 +356,12 @@ static int mpc512x_psc_spi_prep_xfer_hw(struct spi_master *master)
 static int mpc512x_psc_spi_unprep_xfer_hw(struct spi_master *master)
 {
 	struct mpc512x_psc_spi *mps = spi_master_get_devdata(master);
-	struct mpc52xx_psc __iomem *psc = mps->psc;
 	struct mpc512x_psc_fifo __iomem *fifo = mps->fifo;
 
 	dev_dbg(&master->dev, "%s()\n", __func__);
 
 	/* disable transmitter/receiver and fifo interrupt */
-	out_8(&psc->command, MPC52xx_PSC_TX_DISABLE | MPC52xx_PSC_RX_DISABLE);
+	out_8(psc_addr(mps, command), MPC52xx_PSC_TX_DISABLE | MPC52xx_PSC_RX_DISABLE);
 	out_be32(&fifo->tximr, 0);
 
 	return 0;
@@ -388,7 +411,6 @@ static void mpc512x_psc_spi_cleanup(struct spi_device *spi)
 static int mpc512x_psc_spi_port_config(struct spi_master *master,
 				       struct mpc512x_psc_spi *mps)
 {
-	struct mpc52xx_psc __iomem *psc = mps->psc;
 	struct mpc512x_psc_fifo __iomem *fifo = mps->fifo;
 	u32 sicr;
 	u32 ccr;
@@ -396,12 +418,12 @@ static int mpc512x_psc_spi_port_config(struct spi_master *master,
 	u16 bclkdiv;
 
 	/* Reset the PSC into a known state */
-	out_8(&psc->command, MPC52xx_PSC_RST_RX);
-	out_8(&psc->command, MPC52xx_PSC_RST_TX);
-	out_8(&psc->command, MPC52xx_PSC_TX_DISABLE | MPC52xx_PSC_RX_DISABLE);
+	out_8(psc_addr(mps, command), MPC52xx_PSC_RST_RX);
+	out_8(psc_addr(mps, command), MPC52xx_PSC_RST_TX);
+	out_8(psc_addr(mps, command), MPC52xx_PSC_TX_DISABLE | MPC52xx_PSC_RX_DISABLE);
 
 	/* Disable psc interrupts all useful interrupts are in fifo */
-	out_be16(&psc->isr_imr.imr, 0);
+	out_be16(psc_addr(mps, isr_imr.imr), 0);
 
 	/* Disable fifo interrupts, will be enabled later */
 	out_be32(&fifo->tximr, 0);
@@ -417,18 +439,18 @@ static int mpc512x_psc_spi_port_config(struct spi_master *master,
 		0x00004000 |	/* MSTR = 1   -- SPI master */
 		0x00000800;	/* UseEOF = 1 -- SS low until EOF */
 
-	out_be32(&psc->sicr, sicr);
+	out_be32(psc_addr(mps, sicr), sicr);
 
-	ccr = in_be32(&psc->ccr);
+	ccr = in_be32(psc_addr(mps, ccr));
 	ccr &= 0xFF000000;
 	speed = 1000000;	/* default 1MHz */
 	bclkdiv = (mps->mclk_rate / speed) - 1;
 	ccr |= (((bclkdiv & 0xff) << 16) | (((bclkdiv >> 8) & 0xff) << 8));
-	out_be32(&psc->ccr, ccr);
+	out_be32(psc_addr(mps, ccr), ccr);
 
 	/* Set 2ms DTL delay */
-	out_8(&psc->ctur, 0x00);
-	out_8(&psc->ctlr, 0x82);
+	out_8(psc_addr(mps, ctur), 0x00);
+	out_8(psc_addr(mps, ctlr), 0x82);
 
 	/* we don't use the alarms */
 	out_be32(&fifo->rxalarm, 0xfff);
@@ -482,6 +504,7 @@ static int mpc512x_psc_spi_do_probe(struct device *dev, u32 regaddr,
 
 	dev_set_drvdata(dev, master);
 	mps = spi_master_get_devdata(master);
+	mps->type = (int)of_device_get_match_data(dev);
 	mps->irq = irq;
 
 	if (pdata == NULL) {
@@ -589,7 +612,8 @@ static int mpc512x_psc_spi_of_remove(struct platform_device *op)
 }
 
 static const struct of_device_id mpc512x_psc_spi_of_match[] = {
-	{ .compatible = "fsl,mpc5121-psc-spi", },
+	{ .compatible = "fsl,mpc5121-psc-spi", .data = (void *)TYPE_MPC5121 },
+	{ .compatible = "fsl,mpc5125-psc-spi", .data = (void *)TYPE_MPC5125 },
 	{},
 };
 

drivers/spi/spi-omap2-mcspi.c

@@ -245,6 +245,7 @@ static void omap2_mcspi_set_enable(const struct spi_device *spi, int enable)
 
 static void omap2_mcspi_set_cs(struct spi_device *spi, bool enable)
 {
+	struct omap2_mcspi *mcspi = spi_master_get_devdata(spi->master);
 	u32 l;
 
 	/* The controller handles the inverted chip selects
@@ -255,6 +256,12 @@ static void omap2_mcspi_set_cs(struct spi_device *spi, bool enable)
 		enable = !enable;
 
 	if (spi->controller_state) {
+		int err = pm_runtime_get_sync(mcspi->dev);
+		if (err < 0) {
+			dev_err(mcspi->dev, "failed to get sync: %d\n", err);
+			return;
+		}
+
 		l = mcspi_cached_chconf0(spi);
 
 		if (enable)
@@ -263,6 +270,9 @@ static void omap2_mcspi_set_cs(struct spi_device *spi, bool enable)
 			l |= OMAP2_MCSPI_CHCONF_FORCE;
 
 		mcspi_write_chconf0(spi, l);
+
+		pm_runtime_mark_last_busy(mcspi->dev);
+		pm_runtime_put_autosuspend(mcspi->dev);
 	}
 }
 

drivers/spi/spi-orion.c

@@ -41,6 +41,11 @@
 #define ORION_SPI_DATA_OUT_REG		0x08
 #define ORION_SPI_DATA_IN_REG		0x0c
 #define ORION_SPI_INT_CAUSE_REG		0x10
+#define ORION_SPI_TIMING_PARAMS_REG	0x18
+
+#define ORION_SPI_TMISO_SAMPLE_MASK	(0x3 << 6)
+#define ORION_SPI_TMISO_SAMPLE_1	(1 << 6)
+#define ORION_SPI_TMISO_SAMPLE_2	(2 << 6)
 
 #define ORION_SPI_MODE_CPOL		(1 << 11)
 #define ORION_SPI_MODE_CPHA		(1 << 12)
@@ -70,6 +75,7 @@ struct orion_spi_dev {
 	unsigned int		min_divisor;
 	unsigned int		max_divisor;
 	u32			prescale_mask;
+	bool			is_errata_50mhz_ac;
 };
 
 struct orion_spi {
@@ -195,6 +201,41 @@ orion_spi_mode_set(struct spi_device *spi)
 	writel(reg, spi_reg(orion_spi, ORION_SPI_IF_CONFIG_REG));
 }
 
+static void
+orion_spi_50mhz_ac_timing_erratum(struct spi_device *spi, unsigned int speed)
+{
+	u32 reg;
+	struct orion_spi *orion_spi;
+
+	orion_spi = spi_master_get_devdata(spi->master);
+
+	/*
+	 * Erratum description: (Erratum NO. FE-9144572) The device
+	 * SPI interface supports frequencies of up to 50 MHz.
+	 * However, due to this erratum, when the device core clock is
+	 * 250 MHz and the SPI interfaces is configured for 50MHz SPI
+	 * clock and CPOL=CPHA=1 there might occur data corruption on
+	 * reads from the SPI device.
+	 * Erratum Workaround:
+	 * Work in one of the following configurations:
+	 * 1. Set CPOL=CPHA=0 in "SPI Interface Configuration
+	 * Register".
+	 * 2. Set TMISO_SAMPLE value to 0x2 in "SPI Timing Parameters 1
+	 * Register" before setting the interface.
+	 */
+	reg = readl(spi_reg(orion_spi, ORION_SPI_TIMING_PARAMS_REG));
+	reg &= ~ORION_SPI_TMISO_SAMPLE_MASK;
+
+	if (clk_get_rate(orion_spi->clk) == 250000000 &&
+			speed == 50000000 && spi->mode & SPI_CPOL &&
+			spi->mode & SPI_CPHA)
+		reg |= ORION_SPI_TMISO_SAMPLE_2;
+	else
+		reg |= ORION_SPI_TMISO_SAMPLE_1; /* This is the default value */
+
+	writel(reg, spi_reg(orion_spi, ORION_SPI_TIMING_PARAMS_REG));
+}
+
 /*
  * called only when no transfer is active on the bus
  */
@@ -216,6 +257,9 @@ orion_spi_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
 
 	orion_spi_mode_set(spi);
 
+	if (orion_spi->devdata->is_errata_50mhz_ac)
+		orion_spi_50mhz_ac_timing_erratum(spi, speed);
+
 	rc = orion_spi_baudrate_set(spi, speed);
 	if (rc)
 		return rc;
@@ -413,6 +457,14 @@ static const struct orion_spi_dev armada_375_spi_dev_data = {
 	.prescale_mask = ARMADA_SPI_CLK_PRESCALE_MASK,
 };
 
+static const struct orion_spi_dev armada_380_spi_dev_data = {
+	.typ = ARMADA_SPI,
+	.max_hz = 50000000,
+	.max_divisor = 1920,
+	.prescale_mask = ARMADA_SPI_CLK_PRESCALE_MASK,
+	.is_errata_50mhz_ac = true,
+};
+
 static const struct of_device_id orion_spi_of_match_table[] = {
 	{
 		.compatible = "marvell,orion-spi",
@@ -428,7 +480,7 @@ static const struct of_device_id orion_spi_of_match_table[] = {
 	},
 	{
 		.compatible = "marvell,armada-380-spi",
-		.data = &armada_xp_spi_dev_data,
+		.data = &armada_380_spi_dev_data,
 	},
 	{
 		.compatible = "marvell,armada-390-spi",

drivers/spi/spi-pxa2xx-pci.c

@@ -7,7 +7,6 @@
 #include <linux/of_device.h>
 #include <linux/module.h>
 #include <linux/spi/pxa2xx_spi.h>
-#include <linux/clk.h>
 #include <linux/clk-provider.h>
 
 #include <linux/dmaengine.h>

drivers/spi/spi-pxa2xx.c

@@ -21,6 +21,7 @@
 #include <linux/err.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
+#include <linux/pci.h>
 #include <linux/platform_device.h>
 #include <linux/spi/pxa2xx_spi.h>
 #include <linux/spi/spi.h>
@@ -97,6 +98,15 @@ static const struct lpss_config lpss_platforms[] = {
 		.tx_threshold_lo = 160,
 		.tx_threshold_hi = 224,
 	},
+	{	/* LPSS_SPT_SSP */
+		.offset = 0x200,
+		.reg_general = -1,
+		.reg_ssp = 0x20,
+		.reg_cs_ctrl = 0x24,
+		.rx_threshold = 1,
+		.tx_threshold_lo = 32,
+		.tx_threshold_hi = 56,
+	},
 };
 
 static inline const struct lpss_config
@@ -110,6 +120,7 @@ static bool is_lpss_ssp(const struct driver_data *drv_data)
 	switch (drv_data->ssp_type) {
 	case LPSS_LPT_SSP:
 	case LPSS_BYT_SSP:
+	case LPSS_SPT_SSP:
 		return true;
 	default:
 		return false;
@@ -1107,6 +1118,7 @@ static int setup(struct spi_device *spi)
 		break;
 	case LPSS_LPT_SSP:
 	case LPSS_BYT_SSP:
+	case LPSS_SPT_SSP:
 		config = lpss_get_config(drv_data);
 		tx_thres = config->tx_threshold_lo;
 		tx_hi_thres = config->tx_threshold_hi;
@@ -1276,6 +1288,31 @@ static const struct acpi_device_id pxa2xx_spi_acpi_match[] = {
 };
 MODULE_DEVICE_TABLE(acpi, pxa2xx_spi_acpi_match);
 
+/*
+ * PCI IDs of compound devices that integrate both host controller and private
+ * integrated DMA engine. Please note these are not used in module
+ * autoloading and probing in this module but matching the LPSS SSP type.
+ */
+static const struct pci_device_id pxa2xx_spi_pci_compound_match[] = {
+	/* SPT-LP */
+	{ PCI_VDEVICE(INTEL, 0x9d29), LPSS_SPT_SSP },
+	{ PCI_VDEVICE(INTEL, 0x9d2a), LPSS_SPT_SSP },
+	/* SPT-H */
+	{ PCI_VDEVICE(INTEL, 0xa129), LPSS_SPT_SSP },
+	{ PCI_VDEVICE(INTEL, 0xa12a), LPSS_SPT_SSP },
+	{ },
+};
+
+static bool pxa2xx_spi_idma_filter(struct dma_chan *chan, void *param)
+{
+	struct device *dev = param;
+
+	if (dev != chan->device->dev->parent)
+		return false;
+
+	return true;
+}
+
 static struct pxa2xx_spi_master *
 pxa2xx_spi_acpi_get_pdata(struct platform_device *pdev)
 {
@@ -1283,16 +1320,25 @@ pxa2xx_spi_acpi_get_pdata(struct platform_device *pdev)
 	struct acpi_device *adev;
 	struct ssp_device *ssp;
 	struct resource *res;
-	const struct acpi_device_id *id;
+	const struct acpi_device_id *adev_id = NULL;
+	const struct pci_device_id *pcidev_id = NULL;
 	int devid, type;
 
 	if (!ACPI_HANDLE(&pdev->dev) ||
 	    acpi_bus_get_device(ACPI_HANDLE(&pdev->dev), &adev))
 		return NULL;
 
-	id = acpi_match_device(pdev->dev.driver->acpi_match_table, &pdev->dev);
-	if (id)
-		type = (int)id->driver_data;
+	if (dev_is_pci(pdev->dev.parent))
+		pcidev_id = pci_match_id(pxa2xx_spi_pci_compound_match,
+					 to_pci_dev(pdev->dev.parent));
+	else
+		adev_id = acpi_match_device(pdev->dev.driver->acpi_match_table,
+					    &pdev->dev);
+
+	if (adev_id)
+		type = (int)adev_id->driver_data;
+	else if (pcidev_id)
+		type = (int)pcidev_id->driver_data;
 	else
 		return NULL;
 
@@ -1311,6 +1357,12 @@ pxa2xx_spi_acpi_get_pdata(struct platform_device *pdev)
 	if (IS_ERR(ssp->mmio_base))
 		return NULL;
 
+	if (pcidev_id) {
+		pdata->tx_param = pdev->dev.parent;
+		pdata->rx_param = pdev->dev.parent;
+		pdata->dma_filter = pxa2xx_spi_idma_filter;
+	}
+
 	ssp->clk = devm_clk_get(&pdev->dev, NULL);
 	ssp->irq = platform_get_irq(pdev, 0);
 	ssp->type = type;
@@ -1362,8 +1414,7 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
-	/* Allocate master with space for drv_data and null dma buffer */
-	master = spi_alloc_master(dev, sizeof(struct driver_data) + 16);
+	master = spi_alloc_master(dev, sizeof(struct driver_data));
 	if (!master) {
 		dev_err(&pdev->dev, "cannot alloc spi_master\n");
 		pxa_ssp_free(ssp);
@@ -1390,7 +1441,6 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	master->auto_runtime_pm = true;
 
 	drv_data->ssp_type = ssp->type;
-	drv_data->null_dma_buf = (u32 *)PTR_ALIGN(&drv_data[1], DMA_ALIGNMENT);
 
 	drv_data->ioaddr = ssp->mmio_base;
 	drv_data->ssdr_physical = ssp->phys_base + SSDR;
@@ -1424,8 +1474,6 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	}
 
 	/* Setup DMA if requested */
-	drv_data->tx_channel = -1;
-	drv_data->rx_channel = -1;
 	if (platform_info->enable_dma) {
 		status = pxa2xx_spi_dma_setup(drv_data);
 		if (status) {

drivers/spi/spi-pxa2xx.h

@@ -36,11 +36,6 @@ struct driver_data {
 	/* PXA hookup */
 	struct pxa2xx_spi_master *master_info;
 
-	/* PXA private DMA setup stuff */
-	int rx_channel;
-	int tx_channel;
-	u32 *null_dma_buf;
-
 	/* SSP register addresses */
 	void __iomem *ioaddr;
 	u32 ssdr_physical;

drivers/spi/spi-rockchip.c

@@ -645,7 +645,6 @@ static int rockchip_spi_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, master);
 
 	rs = spi_master_get_devdata(master);
-	memset(rs, 0, sizeof(struct rockchip_spi));
 
 	/* Get basic io resource and map it */
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);

drivers/spi/spi-rspi.c

@@ -383,7 +383,8 @@ static void qspi_update(const struct rspi_data *rspi, u8 mask, u8 val, u8 reg)
 	rspi_write8(rspi, data, reg);
 }
 
-static int qspi_set_send_trigger(struct rspi_data *rspi, unsigned int len)
+static unsigned int qspi_set_send_trigger(struct rspi_data *rspi,
+					  unsigned int len)
 {
 	unsigned int n;
 
@@ -724,25 +725,25 @@ static int rspi_rz_transfer_one(struct spi_master *master,
 static int qspi_trigger_transfer_out_in(struct rspi_data *rspi, const u8 *tx,
 					u8 *rx, unsigned int len)
 {
-	int i, n, ret;
-	int error;
+	unsigned int i, n;
+	int ret;
 
 	while (len > 0) {
 		n = qspi_set_send_trigger(rspi, len);
 		qspi_set_receive_trigger(rspi, len);
 		if (n == QSPI_BUFFER_SIZE) {
-			error = rspi_wait_for_tx_empty(rspi);
-			if (error < 0) {
+			ret = rspi_wait_for_tx_empty(rspi);
+			if (ret < 0) {
 				dev_err(&rspi->master->dev, "transmit timeout\n");
-				return error;
+				return ret;
 			}
 			for (i = 0; i < n; i++)
 				rspi_write_data(rspi, *tx++);
 
-			error = rspi_wait_for_rx_full(rspi);
-			if (error < 0) {
+			ret = rspi_wait_for_rx_full(rspi);
+			if (ret < 0) {
 				dev_err(&rspi->master->dev, "receive timeout\n");
-				return error;
+				return ret;
 			}
 			for (i = 0; i < n; i++)
 				*rx++ = rspi_read_data(rspi);

drivers/spi/spi-s3c24xx.c

@@ -501,7 +501,6 @@ static int s3c24xx_spi_probe(struct platform_device *pdev)
 	}
 
 	hw = spi_master_get_devdata(master);
-	memset(hw, 0, sizeof(struct s3c24xx_spi));
 
 	hw->master = master;
 	hw->pdata = pdata = dev_get_platdata(&pdev->dev);

drivers/spi/spi-s3c64xx.c

@@ -1191,8 +1191,8 @@ static int s3c64xx_spi_probe(struct platform_device *pdev)
 
 	dev_dbg(&pdev->dev, "Samsung SoC SPI Driver loaded for Bus SPI-%d with %d Slaves attached\n",
 					sdd->port_id, master->num_chipselect);
-	dev_dbg(&pdev->dev, "\tIOmem=[%pR]\tDMA=[Rx-%d, Tx-%d]\n",
-					mem_res,
+	dev_dbg(&pdev->dev, "\tIOmem=[%pR]\tFIFO %dbytes\tDMA=[Rx-%d, Tx-%d]\n",
+					mem_res, (FIFO_LVL_MASK(sdd) >> 1) + 1,
 					sdd->rx_dma.dmach, sdd->tx_dma.dmach);
 
 	return 0;

drivers/spi/spi-sh-msiof.c

@@ -48,8 +48,8 @@ struct sh_msiof_spi_priv {
 	const struct sh_msiof_chipdata *chipdata;
 	struct sh_msiof_spi_info *info;
 	struct completion done;
-	int tx_fifo_size;
-	int rx_fifo_size;
+	unsigned int tx_fifo_size;
+	unsigned int rx_fifo_size;
 	void *tx_dma_page;
 	void *rx_dma_page;
 	dma_addr_t tx_dma_addr;
@@ -95,8 +95,6 @@ struct sh_msiof_spi_priv {
 #define MDR2_WDLEN1(i)	(((i) - 1) << 16) /* Word Count (1-64/256 (SH, A1))) */
 #define MDR2_GRPMASK1	0x00000001 /* Group Output Mask 1 (SH, A1) */
 
-#define MAX_WDLEN	256U
-
 /* TSCR and RSCR */
 #define SCR_BRPS_MASK	    0x1f00 /* Prescaler Setting (1-32) */
 #define SCR_BRPS(i)	(((i) - 1) << 8)
@@ -850,7 +848,12 @@ static int sh_msiof_transfer_one(struct spi_master *master,
 		 *  DMA supports 32-bit words only, hence pack 8-bit and 16-bit
 		 *  words, with byte resp. word swapping.
 		 */
-		unsigned int l = min(len, MAX_WDLEN * 4);
+		unsigned int l = 0;
+
+		if (tx_buf)
+			l = min(len, p->tx_fifo_size * 4);
+		if (rx_buf)
+			l = min(len, p->rx_fifo_size * 4);
 
 		if (bits <= 8) {
 			if (l & 3)
@@ -963,7 +966,7 @@ static const struct sh_msiof_chipdata sh_data = {
 
 static const struct sh_msiof_chipdata r8a779x_data = {
 	.tx_fifo_size = 64,
-	.rx_fifo_size = 256,
+	.rx_fifo_size = 64,
 	.master_flags = SPI_MASTER_MUST_TX,
 };
 
@@ -1265,11 +1268,6 @@ static int sh_msiof_spi_remove(struct platform_device *pdev)
 
 static const struct platform_device_id spi_driver_ids[] = {
 	{ "spi_sh_msiof",	(kernel_ulong_t)&sh_data },
-	{ "spi_r8a7790_msiof",	(kernel_ulong_t)&r8a779x_data },
-	{ "spi_r8a7791_msiof",	(kernel_ulong_t)&r8a779x_data },
-	{ "spi_r8a7792_msiof",	(kernel_ulong_t)&r8a779x_data },
-	{ "spi_r8a7793_msiof",	(kernel_ulong_t)&r8a779x_data },
-	{ "spi_r8a7794_msiof",	(kernel_ulong_t)&r8a779x_data },
 	{},
 };
 MODULE_DEVICE_TABLE(platform, spi_driver_ids);

drivers/spi/spi-ti-qspi.c

@@ -99,6 +99,8 @@ struct ti_qspi {
 #define QSPI_INVAL			(4 << 16)
 #define QSPI_WC_CMD_INT_EN			(1 << 14)
 #define QSPI_FLEN(n)			((n - 1) << 0)
+#define QSPI_WLEN_MAX_BITS		128
+#define QSPI_WLEN_MAX_BYTES		16
 
 /* STATUS REGISTER */
 #define BUSY				0x01
@@ -217,14 +219,16 @@ static inline u32 qspi_is_busy(struct ti_qspi *qspi)
 
 static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t)
 {
-	int wlen, count;
+	int wlen, count, xfer_len;
 	unsigned int cmd;
 	const u8 *txbuf;
+	u32 data;
 
 	txbuf = t->tx_buf;
 	cmd = qspi->cmd | QSPI_WR_SNGL;
 	count = t->len;
 	wlen = t->bits_per_word >> 3;	/* in bytes */
+	xfer_len = wlen;
 
 	while (count) {
 		if (qspi_is_busy(qspi))
@@ -234,7 +238,29 @@ static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t)
 		case 1:
 			dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %02x\n",
 					cmd, qspi->dc, *txbuf);
-			writeb(*txbuf, qspi->base + QSPI_SPI_DATA_REG);
+			if (count >= QSPI_WLEN_MAX_BYTES) {
+				u32 *txp = (u32 *)txbuf;
+
+				data = cpu_to_be32(*txp++);
+				writel(data, qspi->base +
+				       QSPI_SPI_DATA_REG_3);
+				data = cpu_to_be32(*txp++);
+				writel(data, qspi->base +
+				       QSPI_SPI_DATA_REG_2);
+				data = cpu_to_be32(*txp++);
+				writel(data, qspi->base +
+				       QSPI_SPI_DATA_REG_1);
+				data = cpu_to_be32(*txp++);
+				writel(data, qspi->base +
+				       QSPI_SPI_DATA_REG);
+				xfer_len = QSPI_WLEN_MAX_BYTES;
+				cmd |= QSPI_WLEN(QSPI_WLEN_MAX_BITS);
+			} else {
+				writeb(*txbuf, qspi->base + QSPI_SPI_DATA_REG);
+				cmd = qspi->cmd | QSPI_WR_SNGL;
+				xfer_len = wlen;
+				cmd |= QSPI_WLEN(wlen);
+			}
 			break;
 		case 2:
 			dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %04x\n",
@@ -254,8 +280,8 @@ static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t)
 			dev_err(qspi->dev, "write timed out\n");
 			return -ETIMEDOUT;
 		}
-		txbuf += wlen;
-		count -= wlen;
+		txbuf += xfer_len;
+		count -= xfer_len;
 	}
 
 	return 0;

drivers/spi/spi-xcomm.c

@@ -237,11 +237,11 @@ static const struct i2c_device_id spi_xcomm_ids[] = {
 	{ "spi-xcomm" },
 	{ },
 };
+MODULE_DEVICE_TABLE(i2c, spi_xcomm_ids);
 
 static struct i2c_driver spi_xcomm_driver = {
 	.driver = {
 		.name	= "spi-xcomm",
-		.owner	= THIS_MODULE,
 	},
 	.id_table	= spi_xcomm_ids,
 	.probe		= spi_xcomm_probe,

drivers/spi/spi-xilinx.c

@@ -249,19 +249,23 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
 	xspi->tx_ptr = t->tx_buf;
 	xspi->rx_ptr = t->rx_buf;
 	remaining_words = t->len / xspi->bytes_per_word;
-	reinit_completion(&xspi->done);
 
 	if (xspi->irq >= 0 &&  remaining_words > xspi->buffer_size) {
+		u32 isr;
 		use_irq = true;
-		xspi->write_fn(XSPI_INTR_TX_EMPTY,
-				xspi->regs + XIPIF_V123B_IISR_OFFSET);
-		/* Enable the global IPIF interrupt */
-		xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
-				xspi->regs + XIPIF_V123B_DGIER_OFFSET);
 		/* Inhibit irq to avoid spurious irqs on tx_empty*/
 		cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
 		xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
 			       xspi->regs + XSPI_CR_OFFSET);
+		/* ACK old irqs (if any) */
+		isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
+		if (isr)
+			xspi->write_fn(isr,
+				       xspi->regs + XIPIF_V123B_IISR_OFFSET);
+		/* Enable the global IPIF interrupt */
+		xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
+				xspi->regs + XIPIF_V123B_DGIER_OFFSET);
+		reinit_completion(&xspi->done);
 	}
 
 	while (remaining_words) {
@@ -302,8 +306,10 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
 		remaining_words -= n_words;
 	}
 
-	if (use_irq)
+	if (use_irq) {
 		xspi->write_fn(0, xspi->regs + XIPIF_V123B_DGIER_OFFSET);
+		xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
+	}
 
 	return t->len;
 }

drivers/spi/spidev.c

@@ -602,11 +602,11 @@ static int spidev_open(struct inode *inode, struct file *filp)
 	if (!spidev->tx_buffer) {
 		spidev->tx_buffer = kmalloc(bufsiz, GFP_KERNEL);
 		if (!spidev->tx_buffer) {
-				dev_dbg(&spidev->spi->dev, "open/ENOMEM\n");
-				status = -ENOMEM;
+			dev_dbg(&spidev->spi->dev, "open/ENOMEM\n");
+			status = -ENOMEM;
 			goto err_find_dev;
-			}
 		}
+	}
 
 	if (!spidev->rx_buffer) {
 		spidev->rx_buffer = kmalloc(bufsiz, GFP_KERNEL);
@@ -709,7 +709,7 @@ static int spidev_probe(struct spi_device *spi)
 
 	/*
 	 * spidev should never be referenced in DT without a specific
-	 * compatbile string, it is a Linux implementation thing
+	 * compatible string, it is a Linux implementation thing
 	 * rather than a description of the hardware.
 	 */
 	if (spi->dev.of_node && !of_match_device(spidev_dt_ids, &spi->dev)) {

include/linux/platform_data/spi-davinci.h

@@ -49,6 +49,7 @@ struct davinci_spi_platform_data {
 	u8			num_chipselect;
 	u8			intr_line;
 	u8			*chip_sel;
+	u8			prescaler_limit;
 	bool			cshold_bug;
 	enum dma_event_q	dma_event_q;
 };

include/linux/platform_data/spi-mt65xx.h

+/*
+ *  MTK SPI bus driver definitions
+ *
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Leilk Liu <leilk.liu@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef ____LINUX_PLATFORM_DATA_SPI_MTK_H
+#define ____LINUX_PLATFORM_DATA_SPI_MTK_H
+
+/* Board specific platform_data */
+struct mtk_chip_config {
+	u32 tx_mlsb;
+	u32 rx_mlsb;
+};
+#endif

include/linux/pxa2xx_ssp.h

@@ -197,6 +197,7 @@ enum pxa_ssp_type {
 	QUARK_X1000_SSP,
 	LPSS_LPT_SSP, /* Keep LPSS types sorted with lpss_platforms[] */
 	LPSS_BYT_SSP,
+	LPSS_SPT_SSP,
 };
 
 struct ssp_device {

include/linux/spi/spi.h

@@ -23,6 +23,8 @@
 #include <linux/scatterlist.h>
 
 struct dma_chan;
+struct spi_master;
+struct spi_transfer;
 
 /*
  * INTERFACES between SPI master-side drivers and SPI infrastructure.
@@ -30,6 +32,59 @@ struct dma_chan;
  */
 extern struct bus_type spi_bus_type;
 
+/**
+ * struct spi_statistics - statistics for spi transfers
+ * @clock:         lock protecting this structure
+ *
+ * @messages:      number of spi-messages handled
+ * @transfers:     number of spi_transfers handled
+ * @errors:        number of errors during spi_transfer
+ * @timedout:      number of timeouts during spi_transfer
+ *
+ * @spi_sync:      number of times spi_sync is used
+ * @spi_sync_immediate:
+ *                 number of times spi_sync is executed immediately
+ *                 in calling context without queuing and scheduling
+ * @spi_async:     number of times spi_async is used
+ *
+ * @bytes:         number of bytes transferred to/from device
+ * @bytes_tx:      number of bytes sent to device
+ * @bytes_rx:      number of bytes received from device
+ *
+ */
+struct spi_statistics {
+	spinlock_t		lock; /* lock for the whole structure */
+
+	unsigned long		messages;
+	unsigned long		transfers;
+	unsigned long		errors;
+	unsigned long		timedout;
+
+	unsigned long		spi_sync;
+	unsigned long		spi_sync_immediate;
+	unsigned long		spi_async;
+
+	unsigned long long	bytes;
+	unsigned long long	bytes_rx;
+	unsigned long long	bytes_tx;
+
+};
+
+void spi_statistics_add_transfer_stats(struct spi_statistics *stats,
+				       struct spi_transfer *xfer,
+				       struct spi_master *master);
+
+#define SPI_STATISTICS_ADD_TO_FIELD(stats, field, count)	\
+	do {							\
+		unsigned long flags;				\
+		spin_lock_irqsave(&(stats)->lock, flags);	\
+		(stats)->field += count;			\
+		spin_unlock_irqrestore(&(stats)->lock, flags);	\
+	} while (0)
+
+#define SPI_STATISTICS_INCREMENT_FIELD(stats, field)	\
+	SPI_STATISTICS_ADD_TO_FIELD(stats, field, 1)
+
 /**
  * struct spi_device - Master side proxy for an SPI slave device
  * @dev: Driver model representation of the device.
@@ -60,6 +115,8 @@ extern struct bus_type spi_bus_type;
  * @cs_gpio: gpio number of the chipselect line (optional, -ENOENT when
  *	when not using a GPIO line)
  *
+ * @statistics: statistics for the spi_device
+ *
  * A @spi_device is used to interchange data between an SPI slave
  * (usually a discrete chip) and CPU memory.
  *
@@ -98,6 +155,9 @@ struct spi_device {
 	char			modalias[SPI_NAME_SIZE];
 	int			cs_gpio;	/* chip select gpio */
 
+	/* the statistics */
+	struct spi_statistics	statistics;
+
 	/*
 	 * likely need more hooks for more protocol options affecting how
 	 * the controller talks to each chip, like:
@@ -296,6 +356,7 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
  * @cs_gpios: Array of GPIOs to use as chip select lines; one per CS
  *	number. Any individual value may be -ENOENT for CS lines that
  *	are not GPIOs (driven by the SPI controller itself).
+ * @statistics: statistics for the spi_master
  * @dma_tx: DMA transmit channel
  * @dma_rx: DMA receive channel
  * @dummy_rx: dummy receive buffer for full-duplex devices
@@ -452,6 +513,9 @@ struct spi_master {
 	/* gpio chip select */
 	int			*cs_gpios;
 
+	/* statistics */
+	struct spi_statistics	statistics;
+
 	/* DMA channels for use with core dmaengine helpers */
 	struct dma_chan		*dma_tx;
 	struct dma_chan		*dma_rx;