Commit ee8c446f authored by Mauro S. M. Rodrigues's avatar Mauro S. M. Rodrigues Committed by Michael Ellerman

powerpc/eeh: Avoid misleading message "EEH: no capable adapters found"

Due to recent refactoring in EEH in:
commit b9fde58d ("powerpc/powernv: Rework EEH initialization on
powernv")
a misleading message was seen in the kernel message buffer:

[    0.108431] EEH: PowerNV platform initialized
[    0.589979] EEH: No capable adapters found

This happened due to the removal of the initialization delay for powernv
platform.

Even though the EEH infrastructure for the devices is eventually
initialized and still works just fine the eeh device probe step is
postponed in order to assure the PEs are created. Later
pnv_eeh_post_init does the probe devices job but at that point the
message was already shown right after eeh_init flow.

This patch introduces a new flag EEH_POSTPONED_PROBE to represent that
temporary state and avoid the message mentioned above and showing the
follow one instead:

[    0.107724] EEH: PowerNV platform initialized
[    4.844825] EEH: PCI Enhanced I/O Error Handling Enabled
Signed-off-by: default avatarMauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: default avatarRussell Currey <ruscur@russell.cc>
Tested-by: default avatarVenkat Rao B <vrbagal1@linux.vnet.ibm.com>
Signed-off-by: default avatarMichael Ellerman <mpe@ellerman.id.au>
parent a545cf03
......@@ -36,13 +36,14 @@ struct pci_dn;
#ifdef CONFIG_EEH
/* EEH subsystem flags */
#define EEH_ENABLED 0x01 /* EEH enabled */
#define EEH_FORCE_DISABLED 0x02 /* EEH disabled */
#define EEH_PROBE_MODE_DEV 0x04 /* From PCI device */
#define EEH_PROBE_MODE_DEVTREE 0x08 /* From device tree */
#define EEH_VALID_PE_ZERO 0x10 /* PE#0 is valid */
#define EEH_ENABLE_IO_FOR_LOG 0x20 /* Enable IO for log */
#define EEH_EARLY_DUMP_LOG 0x40 /* Dump log immediately */
#define EEH_ENABLED 0x01 /* EEH enabled */
#define EEH_FORCE_DISABLED 0x02 /* EEH disabled */
#define EEH_PROBE_MODE_DEV 0x04 /* From PCI device */
#define EEH_PROBE_MODE_DEVTREE 0x08 /* From device tree */
#define EEH_VALID_PE_ZERO 0x10 /* PE#0 is valid */
#define EEH_ENABLE_IO_FOR_LOG 0x20 /* Enable IO for log */
#define EEH_EARLY_DUMP_LOG 0x40 /* Dump log immediately */
#define EEH_POSTPONED_PROBE 0x80 /* Powernv may postpone device probe */
/*
* Delay for PE reset, all in ms
......
......@@ -1087,7 +1087,7 @@ static int eeh_init(void)
if (eeh_enabled())
pr_info("EEH: PCI Enhanced I/O Error Handling Enabled\n");
else
else if (!eeh_has_flag(EEH_POSTPONED_PROBE))
pr_info("EEH: No capable adapters found\n");
return ret;
......
......@@ -223,6 +223,14 @@ int pnv_eeh_post_init(void)
eeh_probe_devices();
eeh_addr_cache_build();
if (eeh_has_flag(EEH_POSTPONED_PROBE)) {
eeh_clear_flag(EEH_POSTPONED_PROBE);
if (eeh_enabled())
pr_info("EEH: PCI Enhanced I/O Error Handling Enabled\n");
else
pr_info("EEH: No capable adapters found\n");
}
/* Register OPAL event notifier */
eeh_event_irq = opal_event_request(ilog2(OPAL_EVENT_PCI_ERROR));
if (eeh_event_irq < 0) {
......@@ -384,8 +392,10 @@ static void *pnv_eeh_probe(struct pci_dn *pdn, void *data)
return NULL;
/* Skip if we haven't probed yet */
if (phb->ioda.pe_rmap[config_addr] == IODA_INVALID_PE)
if (phb->ioda.pe_rmap[config_addr] == IODA_INVALID_PE) {
eeh_add_flag(EEH_POSTPONED_PROBE);
return NULL;
}
/* Initialize eeh device */
edev->class_code = pdn->class_code;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment