MIPS: Lantiq: Add support for gphy firmware loading for ar10 and grx390

Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11389/
Patchwork: https://patchwork.linux-mips.org/patch/11398/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/lantiq/xway/reset.c

@@ -4,6 +4,7 @@
  *  by the Free Software Foundation.
  *
  *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
+ *  Copyright (C) 2013-2015 Lantiq Beteiligungs-GmbH & Co.KG
  */
 
 #include <linux/init.h>
@@ -22,9 +23,6 @@
 
 #include "../prom.h"
 
-#define ltq_rcu_w32(x, y)	ltq_w32((x), ltq_rcu_membase + (y))
-#define ltq_rcu_r32(x)		ltq_r32(ltq_rcu_membase + (x))
-
 /* reset request register */
 #define RCU_RST_REQ		0x0010
 /* reset status register */
@@ -32,11 +30,29 @@
 /* vr9 gphy registers */
 #define RCU_GFS_ADD0_XRX200	0x0020
 #define RCU_GFS_ADD1_XRX200	0x0068
+/* xRX300 gphy registers */
+#define RCU_GFS_ADD0_XRX300	0x0020
+#define RCU_GFS_ADD1_XRX300	0x0058
+#define RCU_GFS_ADD2_XRX300	0x00AC
+/* xRX330 gphy registers */
+#define RCU_GFS_ADD0_XRX330	0x0020
+#define RCU_GFS_ADD1_XRX330	0x0058
+#define RCU_GFS_ADD2_XRX330	0x00AC
+#define RCU_GFS_ADD3_XRX330	0x0264
 
 /* reboot bit */
 #define RCU_RD_GPHY0_XRX200	BIT(31)
 #define RCU_RD_SRST		BIT(30)
 #define RCU_RD_GPHY1_XRX200	BIT(29)
+/* xRX300 bits */
+#define RCU_RD_GPHY0_XRX300	BIT(31)
+#define RCU_RD_GPHY1_XRX300	BIT(29)
+#define RCU_RD_GPHY2_XRX300	BIT(28)
+/* xRX330 bits */
+#define RCU_RD_GPHY0_XRX330	BIT(31)
+#define RCU_RD_GPHY1_XRX330	BIT(29)
+#define RCU_RD_GPHY2_XRX330	BIT(28)
+#define RCU_RD_GPHY3_XRX330	BIT(10)
 
 /* reset cause */
 #define RCU_STAT_SHIFT		26
@@ -47,6 +63,26 @@
 /* remapped base addr of the reset control unit */
 static void __iomem *ltq_rcu_membase;
 static struct device_node *ltq_rcu_np;
+static DEFINE_SPINLOCK(ltq_rcu_lock);
+
+static void ltq_rcu_w32(uint32_t val, uint32_t reg_off)
+{
+	ltq_w32(val, ltq_rcu_membase + reg_off);
+}
+
+static uint32_t ltq_rcu_r32(uint32_t reg_off)
+{
+	return ltq_r32(ltq_rcu_membase + reg_off);
+}
+
+static void ltq_rcu_w32_mask(uint32_t clr, uint32_t set, uint32_t reg_off)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ltq_rcu_lock, flags);
+	ltq_rcu_w32((ltq_rcu_r32(reg_off) & ~(clr)) | (set), reg_off);
+	spin_unlock_irqrestore(&ltq_rcu_lock, flags);
+}
 
 /* This function is used by the watchdog driver */
 int ltq_reset_cause(void)
@@ -67,15 +103,40 @@ unsigned char ltq_boot_select(void)
 	return RCU_BOOT_SEL(val);
 }
 
-/* reset / boot a gphy */
-static struct ltq_xrx200_gphy_reset {
+struct ltq_gphy_reset {
 	u32 rd;
 	u32 addr;
-} xrx200_gphy[] = {
+};
+
+/* reset / boot a gphy */
+static struct ltq_gphy_reset xrx200_gphy[] = {
 	{RCU_RD_GPHY0_XRX200, RCU_GFS_ADD0_XRX200},
 	{RCU_RD_GPHY1_XRX200, RCU_GFS_ADD1_XRX200},
 };
 
+/* reset / boot a gphy */
+static struct ltq_gphy_reset xrx300_gphy[] = {
+	{RCU_RD_GPHY0_XRX300, RCU_GFS_ADD0_XRX300},
+	{RCU_RD_GPHY1_XRX300, RCU_GFS_ADD1_XRX300},
+	{RCU_RD_GPHY2_XRX300, RCU_GFS_ADD2_XRX300},
+};
+
+/* reset / boot a gphy */
+static struct ltq_gphy_reset xrx330_gphy[] = {
+	{RCU_RD_GPHY0_XRX330, RCU_GFS_ADD0_XRX330},
+	{RCU_RD_GPHY1_XRX330, RCU_GFS_ADD1_XRX330},
+	{RCU_RD_GPHY2_XRX330, RCU_GFS_ADD2_XRX330},
+	{RCU_RD_GPHY3_XRX330, RCU_GFS_ADD3_XRX330},
+};
+
+static void xrx200_gphy_boot_addr(struct ltq_gphy_reset *phy_regs,
+				  dma_addr_t dev_addr)
+{
+	ltq_rcu_w32_mask(0, phy_regs->rd, RCU_RST_REQ);
+	ltq_rcu_w32(dev_addr, phy_regs->addr);
+	ltq_rcu_w32_mask(phy_regs->rd, 0,  RCU_RST_REQ);
+}
+
 /* reset and boot a gphy. these phys only exist on xrx200 SoC */
 int xrx200_gphy_boot(struct device *dev, unsigned int id, dma_addr_t dev_addr)
 {
@@ -86,23 +147,34 @@ int xrx200_gphy_boot(struct device *dev, unsigned int id, dma_addr_t dev_addr)
 		return -EINVAL;
 	}
 
-	clk = clk_get_sys("1f203000.rcu", "gphy");
-	if (IS_ERR(clk))
-		return PTR_ERR(clk);
-
-	clk_enable(clk);
-
-	if (id > 1) {
-		dev_err(dev, "%u is an invalid gphy id\n", id);
-		return -EINVAL;
+	if (of_machine_is_compatible("lantiq,vr9")) {
+		clk = clk_get_sys("1f203000.rcu", "gphy");
+		if (IS_ERR(clk))
+			return PTR_ERR(clk);
+		clk_enable(clk);
 	}
+
 	dev_info(dev, "booting GPHY%u firmware at %X\n", id, dev_addr);
 
-	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) | xrx200_gphy[id].rd,
-			RCU_RST_REQ);
-	ltq_rcu_w32(dev_addr, xrx200_gphy[id].addr);
-	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) & ~xrx200_gphy[id].rd,
-			RCU_RST_REQ);
+	if (of_machine_is_compatible("lantiq,vr9")) {
+		if (id >= ARRAY_SIZE(xrx200_gphy)) {
+			dev_err(dev, "%u is an invalid gphy id\n", id);
+			return -EINVAL;
+		}
+		xrx200_gphy_boot_addr(&xrx200_gphy[id], dev_addr);
+	} else if (of_machine_is_compatible("lantiq,ar10")) {
+		if (id >= ARRAY_SIZE(xrx300_gphy)) {
+			dev_err(dev, "%u is an invalid gphy id\n", id);
+			return -EINVAL;
+		}
+		xrx200_gphy_boot_addr(&xrx300_gphy[id], dev_addr);
+	} else if (of_machine_is_compatible("lantiq,grx390")) {
+		if (id >= ARRAY_SIZE(xrx330_gphy)) {
+			dev_err(dev, "%u is an invalid gphy id\n", id);
+			return -EINVAL;
+		}
+		xrx200_gphy_boot_addr(&xrx330_gphy[id], dev_addr);
+	}
 	return 0;
 }