[PATCH] e1000: New bit definitions, fix comments on loadtime parameters

drivers/net/e1000/e1000_hw.h

@@ -369,6 +369,9 @@ int32_t e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active);
 
 #define E1000_82542_2_0_REV_ID 2
 #define E1000_82542_2_1_REV_ID 3
+#define E1000_REVISION_0       0
+#define E1000_REVISION_1       1
+#define E1000_REVISION_2       2
 
 #define SPEED_10    10
 #define SPEED_100   100
@@ -763,6 +766,7 @@ struct e1000_ffvt_entry {
 #define E1000_WUPL     0x05900  /* Wakeup Packet Length - RW */
 #define E1000_WUPM     0x05A00  /* Wakeup Packet Memory - RO A */
 #define E1000_FFLT     0x05F00  /* Flexible Filter Length Table - RW Array */
+#define E1000_HOST_IF  0x08800  /* Host Interface */
 #define E1000_FFMT     0x09000  /* Flexible Filter Mask Table - RW Array */
 #define E1000_FFVT     0x09800  /* Flexible Filter Value Table - RW Array */
 
@@ -899,6 +903,7 @@ struct e1000_ffvt_entry {
 #define E1000_82542_TDFT     0x08018
 #define E1000_82542_FFMT     E1000_FFMT
 #define E1000_82542_FFVT     E1000_FFVT
+#define E1000_82542_HOST_IF  E1000_HOST_IF
 
 /* Statistics counters collected by the MAC */
 struct e1000_hw_stats {
@@ -1434,6 +1439,10 @@ struct e1000_hw {
 #define E1000_MANC_TCO_RESET     0x00010000 /* TCO Reset Occurred */
 #define E1000_MANC_RCV_TCO_EN    0x00020000 /* Receive TCO Packets Enabled */
 #define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
+#define E1000_MANC_EN_MAC_ADDR_FILTER   0x00100000 /* Enable MAC address
+                                                    * filtering */
+#define E1000_MANC_EN_MNG2HOST   0x00200000 /* Enable MNG packets to host
+                                             * memory */
 #define E1000_MANC_SMB_REQ       0x01000000 /* SMBus Request */
 #define E1000_MANC_SMB_GNT       0x02000000 /* SMBus Grant */
 #define E1000_MANC_SMB_CLK_IN    0x04000000 /* SMBus Clock In */

drivers/net/e1000/e1000_param.c

@@ -107,7 +107,7 @@ E1000_PARAM(Duplex, "Duplex setting");
 
 /* Auto-negotiation Advertisement Override
  *
- * Valid Range: 0x01-0x0F, 0x20-0x2F
+ * Valid Range: 0x01-0x0F, 0x20-0x2F (copper); 0x20 (fiber)
  *
  * The AutoNeg value is a bit mask describing which speed and duplex
  * combinations should be advertised during auto-negotiation.
@@ -117,7 +117,7 @@ E1000_PARAM(Duplex, "Duplex setting");
  * Speed (Mbps)  N/A   N/A   1000   N/A    100   100   10     10
  * Duplex                    Full          Full  Half  Full   Half
  *
- * Default Value: 0x2F
+ * Default Value: 0x2F (copper); 0x20 (fiber)
  */
 
 E1000_PARAM(AutoNeg, "Advertised auto-negotiation setting");