ARM64: dts: amlogic: Enable pin controller on GXBB-based platforms

Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts

@@ -45,6 +45,7 @@
 /dts-v1/;
 
 #include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
@@ -62,8 +63,20 @@ memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		blue {
+			label = "c2:blue:alive";
+			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
 };
 
 &uart_AO {
 	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
 };

arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi

@@ -62,4 +62,6 @@ memory@0 {
 /* This UART is brought out to the DB9 connector */
 &uart_AO {
 	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
 };

arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi

@@ -56,4 +56,7 @@ chosen {
 
 &uart_AO {
 	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+
 };

arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi

@@ -43,6 +43,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/meson-gxbb-gpio.h>
 
 / {
 	compatible = "amlogic,meson-gxbb";
@@ -158,6 +159,29 @@ aobus: aobus@c8100000 {
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
 
+			pinctrl_aobus: pinctrl@14 {
+				compatible = "amlogic,meson-gxbb-aobus-pinctrl";
+				#address-cells = <2>;
+				#size-cells = <2>;
+				ranges;
+
+				gpio_ao: bank@14 {
+					reg = <0x0 0x00014 0x0 0x8>,
+					      <0x0 0x0002c 0x0 0x4>,
+					      <0x0 0x00024 0x0 0x8>;
+					reg-names = "mux", "pull", "gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+
+				uart_ao_a_pins: uart_ao_a {
+					mux {
+						groups = "uart_tx_ao_a", "uart_rx_ao_a";
+						function = "uart_ao";
+					};
+				};
+			};
+
 			uart_AO: serial@4c0 {
 				compatible = "amlogic,meson-uart";
 				reg = <0x0 0x004c0 0x0 0x14>;
@@ -173,6 +197,23 @@ periphs: periphs@c8834000 {
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
+
+			pinctrl_periphs: pinctrl@4b0 {
+				compatible = "amlogic,meson-gxbb-periphs-pinctrl";
+				#address-cells = <2>;
+				#size-cells = <2>;
+				ranges;
+
+				gpio: bank@4b0 {
+					reg = <0x0 0x004b0 0x0 0x28>,
+					      <0x0 0x004e8 0x0 0x14>,
+					      <0x0 0x00120 0x0 0x14>,
+					      <0x0 0x00430 0x0 0x40>;
+					reg-names = "mux", "pull", "pull-enable", "gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+			};
 		};
 
 		hiubus: hiubus@c883c000 {