tty: esp: remove broken driver

The ESP driver has been marked broken for years. It's an old ISA device
that clearly nobody cares about any more. Remove it
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Documentation/serial/hayes-esp.txt

-HAYES ESP DRIVER VERSION 2.1
-
-A big thanks to the people at Hayes, especially Alan Adamson.  Their support
-has enabled me to provide enhancements to the driver.
-
-Please report your experiences with this driver to me (arobinso@nyx.net).  I
-am looking for both positive and negative feedback.
-
-*** IMPORTANT CHANGES FOR 2.1 ***
-Support for PIO mode.  Five situations will cause PIO mode to be used:
-1) A multiport card is detected.  PIO mode will always be used.  (8 port cards
-do not support DMA).
-2) The DMA channel is set to an invalid value (anything other than 1 or 3).
-3) The DMA buffer/channel could not be allocated.  The port will revert to PIO
-mode until it is reopened.
-4) Less than a specified number of bytes need to be transferred to/from the
-FIFOs.  PIO mode will be used for that transfer only.
-5) A port needs to do a DMA transfer and another port is already using the
-DMA channel.  PIO mode will be used for that transfer only.
-
-Since the Hayes ESP seems to conflict with other cards (notably sound cards)
-when using DMA, DMA is turned off by default.  To use DMA, it must be turned
-on explicitly, either with the "dma=" option described below or with
-setserial.  A multiport card can be forced into DMA mode by using setserial;
-however, most multiport cards don't support DMA.
-
-The latest version of setserial allows the enhanced configuration of the ESP
-card to be viewed and modified.
-***
-
-This package contains the files needed to compile a module to support the Hayes
-ESP card.  The drivers are basically a modified version of the serial drivers.
-
-Features:
-
-- Uses the enhanced mode of the ESP card, allowing a wider range of
-  interrupts and features than compatibility mode
-- Uses DMA and 16 bit PIO mode to transfer data to and from the ESP's FIFOs,
-  reducing CPU load
-- Supports primary and secondary ports
-
-
-If the driver is compiled as a module, the IRQs to use can be specified by
-using the irq= option.  The format is:
-
-irq=[0x100],[0x140],[0x180],[0x200],[0x240],[0x280],[0x300],[0x380]
-
-The address in brackets is the base address of the card.  The IRQ of
-nonexistent cards can be set to 0.  If an IRQ of a card that does exist is set
-to 0, the driver will attempt to guess at the correct IRQ.  For example, to set
-the IRQ of the card at address 0x300 to 12, the insmod command would be:
-
-insmod esp irq=0,0,0,0,0,0,12,0
-
-The custom divisor can be set by using the divisor= option.  The format is the
-same as for the irq= option.  Each divisor value is a series of hex digits,
-with each digit representing the divisor to use for a corresponding port.  The
-divisor value is constructed RIGHT TO LEFT.  Specifying a nonzero divisor value
-will automatically set the spd_cust flag.  To calculate the divisor to use for
-a certain baud rate, divide the port's base baud (generally 921600) by the
-desired rate.  For example, to set the divisor of the primary port at 0x300 to
-4 and the divisor of the secondary port at 0x308 to 8, the insmod command would
-be:
-
-insmod esp divisor=0,0,0,0,0,0,0x84,0
-
-The dma= option can be used to set the DMA channel.  The channel can be either
-1 or 3.  Specifying any other value will force the driver to use PIO mode.
-For example, to set the DMA channel to 3, the insmod command would be:
-
-insmod esp dma=3
-
-The rx_trigger= and tx_trigger= options can be used to set the FIFO trigger
-levels.  They specify when the ESP card should send an interrupt.  Larger
-values will decrease the number of interrupts; however, a value too high may
-result in data loss.  Valid values are 1 through 1023, with 768 being the
-default.  For example, to set the receive trigger level to 512 bytes and the
-transmit trigger level to 700 bytes, the insmod command would be:
-
-insmod esp rx_trigger=512 tx_trigger=700
-
-The flow_off= and flow_on= options can be used to set the hardware flow off/
-flow on levels.  The flow on level must be lower than the flow off level, and
-the flow off level should be higher than rx_trigger.  Valid values are 1
-through 1023, with 1016 being the default flow off level and 944 being the
-default flow on level.  For example, to set the flow off level to 1000 bytes
-and the flow on level to 935 bytes, the insmod command would be:
-
-insmod esp flow_off=1000 flow_on=935
-
-The rx_timeout= option can be used to set the receive timeout value.  This
-value indicates how long after receiving the last character that the ESP card
-should wait before signalling an interrupt.  Valid values are 0 though 255,
-with 128 being the default.  A value too high will increase latency, and a
-value too low will cause unnecessary interrupts.  For example, to set the
-receive timeout to 255, the insmod command would be:
-
-insmod esp rx_timeout=255
-
-The pio_threshold= option sets the threshold (in number of characters) for
-using PIO mode instead of DMA mode.  For example, if this value is 32,
-transfers of 32 bytes or less will always use PIO mode.
-
-insmod esp pio_threshold=32
-
-Multiple options can be listed on the insmod command line by separating each
-option with a space.  For example:
-
-insmod esp dma=3 trigger=512
-
-The esp module can be automatically loaded when needed.  To cause this to
-happen, add the following lines to /etc/modprobe.conf (replacing the last line
-with options for your configuration):
-
-alias char-major-57 esp
-alias char-major-58 esp
-options esp irq=0,0,0,0,0,0,3,0 divisor=0,0,0,0,0,0,0x4,0
-
-You may also need to run 'depmod -a'.
-
-Devices must be created manually.  To create the devices, note the output from
-the module after it is inserted.  The output will appear in the location where
-kernel messages usually appear (usually /var/adm/messages).  Create two devices
-for each 'tty' mentioned, one with major of 57 and the other with major of 58.
-The minor number should be the same as the tty number reported.  The commands
-would be (replace ? with the tty number):
-
-mknod /dev/ttyP? c 57 ?
-mknod /dev/cup? c 58 ?
-
-For example, if the following line appears:
-
-Oct 24 18:17:23 techno kernel: ttyP8 at 0x0140 (irq = 3) is an ESP primary port
-
-...two devices should be created:
-
-mknod /dev/ttyP8 c 57 8
-mknod /dev/cup8 c 58 8
-
-You may need to set the permissions on the devices:
-
-chmod 666 /dev/ttyP*
-chmod 666 /dev/cup*
-
-The ESP module and the serial module should not conflict (they can be used at
-the same time).  After the ESP module has been loaded the ports on the ESP card
-will no longer be accessible by the serial driver.
-
-If I/O errors are experienced when accessing the port, check for IRQ and DMA
-conflicts ('cat /proc/interrupts' and 'cat /proc/dma' for a list of IRQs and
-DMAs currently in use).
-
-Enjoy!
-Andrew J. Robinson <arobinso@nyx.net>

drivers/char/Kconfig

@@ -201,19 +201,6 @@ config DIGIEPCA
 	  To compile this driver as a module, choose M here: the
 	  module will be called epca.
 
-config ESPSERIAL
-	tristate "Hayes ESP serial port support"
-	depends on SERIAL_NONSTANDARD && ISA && ISA_DMA_API && BROKEN
-	help
-	  This is a driver which supports Hayes ESP serial ports.  Both single
-	  port cards and multiport cards are supported.  Make sure to read
-	  <file:Documentation/hayes-esp.txt>.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called esp.
-
-	  If unsure, say N.
-
 config MOXA_INTELLIO
 	tristate "Moxa Intellio support"
 	depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI)

drivers/char/Makefile

@@ -18,7 +18,6 @@ obj-$(CONFIG_CONSOLE_TRANSLATIONS) += consolemap.o consolemap_deftbl.o
 obj-$(CONFIG_HW_CONSOLE)	+= vt.o defkeymap.o
 obj-$(CONFIG_AUDIT)		+= tty_audit.o
 obj-$(CONFIG_MAGIC_SYSRQ)	+= sysrq.o
-obj-$(CONFIG_ESPSERIAL)		+= esp.o
 obj-$(CONFIG_MVME147_SCC)	+= generic_serial.o vme_scc.o
 obj-$(CONFIG_MVME162_SCC)	+= generic_serial.o vme_scc.o
 obj-$(CONFIG_BVME6000_SCC)	+= generic_serial.o vme_scc.o

include/linux/Kbuild

@@ -214,7 +214,6 @@ unifdef-y += futex.h
 unifdef-y += fs.h
 unifdef-y += gameport.h
 unifdef-y += generic_serial.h
-unifdef-y += hayesesp.h
 unifdef-y += hdlcdrv.h
 unifdef-y += hdlc.h
 unifdef-y += hdreg.h

include/linux/hayesesp.h

-#ifndef HAYESESP_H
-#define HAYESESP_H
-
-struct hayes_esp_config {
-	short flow_on;
-	short flow_off;
-	short rx_trigger;
-	short tx_trigger;
-	short pio_threshold;
-	unsigned char rx_timeout;
-	char dma_channel;
-};
-
-#ifdef __KERNEL__
-
-#define ESP_DMA_CHANNEL   0
-#define ESP_RX_TRIGGER    768
-#define ESP_TX_TRIGGER    768
-#define ESP_FLOW_OFF      1016
-#define ESP_FLOW_ON       944
-#define ESP_RX_TMOUT      128
-#define ESP_PIO_THRESHOLD 32
-
-#define ESP_IN_MAJOR	57	/* major dev # for dial in */
-#define ESP_OUT_MAJOR	58	/* major dev # for dial out */
-#define ESPC_SCALE 	3
-#define UART_ESI_BASE	0x00
-#define UART_ESI_SID	0x01
-#define UART_ESI_RX	0x02
-#define UART_ESI_TX	0x02
-#define UART_ESI_CMD1	0x04
-#define UART_ESI_CMD2	0x05
-#define UART_ESI_STAT1	0x04
-#define UART_ESI_STAT2	0x05
-#define UART_ESI_RWS	0x07
-
-#define UART_IER_DMA_TMOUT	0x80
-#define UART_IER_DMA_TC		0x08
-
-#define ESI_SET_IRQ		0x04
-#define ESI_SET_DMA_TMOUT	0x05
-#define ESI_SET_SRV_MASK	0x06
-#define ESI_SET_ERR_MASK	0x07
-#define ESI_SET_FLOW_CNTL	0x08
-#define ESI_SET_FLOW_CHARS	0x09
-#define ESI_SET_FLOW_LVL	0x0a
-#define ESI_SET_TRIGGER		0x0b
-#define ESI_SET_RX_TIMEOUT	0x0c
-#define ESI_SET_FLOW_TMOUT	0x0d
-#define ESI_WRITE_UART		0x0e
-#define ESI_READ_UART		0x0f
-#define ESI_SET_MODE		0x10
-#define ESI_GET_ERR_STAT	0x12
-#define ESI_GET_UART_STAT	0x13
-#define ESI_GET_RX_AVAIL	0x14
-#define ESI_GET_TX_AVAIL	0x15
-#define ESI_START_DMA_RX	0x16
-#define ESI_START_DMA_TX	0x17
-#define ESI_ISSUE_BREAK		0x1a
-#define ESI_FLUSH_RX		0x1b
-#define ESI_FLUSH_TX		0x1c
-#define ESI_SET_BAUD		0x1d
-#define ESI_SET_ENH_IRQ		0x1f
-#define ESI_SET_REINTR		0x20
-#define ESI_SET_PRESCALAR	0x23
-#define ESI_NO_COMMAND		0xff
-
-#define ESP_STAT_RX_TIMEOUT	0x01
-#define ESP_STAT_DMA_RX		0x02
-#define ESP_STAT_DMA_TX		0x04
-#define ESP_STAT_NEVER_DMA      0x08
-#define ESP_STAT_USE_PIO        0x10
-
-#define ESP_MAGIC		0x53ee
-#define ESP_XMIT_SIZE		4096
-
-struct esp_struct {
-	int			magic;
-	struct tty_port		port;
-	spinlock_t		lock;
-	int			io_port;
-	int			irq;
-	int			read_status_mask;
-	int			ignore_status_mask;
-	int			timeout;
-	int			stat_flags;
-	int			custom_divisor;
-	int			close_delay;
-	unsigned short		closing_wait;
-	unsigned short		closing_wait2;
-	int			IER; 	/* Interrupt Enable Register */
-	int			MCR; 	/* Modem control register */
-	unsigned long		last_active;
-	int			line;
-	unsigned char 		*xmit_buf;
-	int			xmit_head;
-	int			xmit_tail;
-	int			xmit_cnt;
-	wait_queue_head_t	break_wait;
-	struct async_icount	icount;	/* kernel counters for the 4 input interrupts */
-	struct hayes_esp_config config; /* port configuration */
-	struct esp_struct	*next_port; /* For the linked list */
-};
-
-struct esp_pio_buffer {
-	unsigned char data[1024];
-	struct esp_pio_buffer *next;
-};
-
-#endif /* __KERNEL__ */
-
-
-#endif /* ESP_H */
-