serial: 8250: Add Nuvoton NPCM UART

The Nuvoton UART is almost compatible with the 8250 driver when probed
via the 8250_of driver, however it requires some extra configuration
at startup.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/devicetree/bindings/serial/8250.txt

@@ -24,6 +24,7 @@ Required properties:
 	- "ti,da830-uart"
 	- "aspeed,ast2400-vuart"
 	- "aspeed,ast2500-vuart"
+	- "nuvoton,npcm750-uart"
 	- "serial" if the port type is unknown.
 - reg : offset and length of the register set for the device.
 - interrupts : should contain uart interrupt.

drivers/tty/serial/8250/8250_of.c

@@ -316,6 +316,7 @@ static const struct of_device_id of_platform_serial_table[] = {
 	{ .compatible = "mrvl,mmp-uart",
 		.data = (void *)PORT_XSCALE, },
 	{ .compatible = "ti,da830-uart", .data = (void *)PORT_DA830, },
+	{ .compatible = "nuvoton,npcm750-uart", .data = (void *)PORT_NPCM, },
 	{ /* end of list */ },
 };
 MODULE_DEVICE_TABLE(of, of_platform_serial_table);

drivers/tty/serial/8250/8250_port.c

@@ -47,6 +47,10 @@
 #define UART_EXAR_SLEEP		0x8b	/* Sleep mode */
 #define UART_EXAR_DVID		0x8d	/* Device identification */
 
+/* Nuvoton NPCM timeout register */
+#define UART_NPCM_TOR          7
+#define UART_NPCM_TOIE         BIT(7)  /* Timeout Interrupt Enable */
+
 /*
  * Debugging.
  */
@@ -293,6 +297,15 @@ static const struct serial8250_config uart_config[] = {
 				  UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
 		.flags		= UART_CAP_FIFO,
 	},
+	[PORT_NPCM] = {
+		.name		= "Nuvoton 16550",
+		.fifo_size	= 16,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
+				  UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
+		.rxtrig_bytes	= {1, 4, 8, 14},
+		.flags		= UART_CAP_FIFO,
+	},
 };
 
 /* Uart divisor latch read */
@@ -2141,6 +2154,15 @@ int serial8250_do_startup(struct uart_port *port)
 				UART_DA830_PWREMU_MGMT_FREE);
 	}
 
+	if (port->type == PORT_NPCM) {
+		/*
+		 * Nuvoton calls the scratch register 'UART_TOR' (timeout
+		 * register). Enable it, and set TIOC (timeout interrupt
+		 * comparator) to be 0x20 for correct operation.
+		 */
+		serial_port_out(port, UART_NPCM_TOR, UART_NPCM_TOIE | 0x20);
+	}
+
 #ifdef CONFIG_SERIAL_8250_RSA
 	/*
 	 * If this is an RSA port, see if we can kick it up to the
@@ -2463,6 +2485,15 @@ static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up,
 	return quot_16 >> 4;
 }
 
+/* Nuvoton NPCM UARTs have a custom divisor calculation */
+static unsigned int npcm_get_divisor(struct uart_8250_port *up,
+		unsigned int baud)
+{
+	struct uart_port *port = &up->port;
+
+	return DIV_ROUND_CLOSEST(port->uartclk, 16 * baud + 2) - 2;
+}
+
 static unsigned int serial8250_get_divisor(struct uart_8250_port *up,
 					   unsigned int baud,
 					   unsigned int *frac)
@@ -2483,6 +2514,8 @@ static unsigned int serial8250_get_divisor(struct uart_8250_port *up,
 		quot = 0x8002;
 	else if (up->port.type == PORT_XR17V35X)
 		quot = xr17v35x_get_divisor(up, baud, frac);
+	else if (up->port.type == PORT_NPCM)
+		quot = npcm_get_divisor(up, baud);
 	else
 		quot = uart_get_divisor(port, baud);
 

include/uapi/linux/serial_core.h

@@ -76,6 +76,9 @@
 #define PORT_SUNZILOG	38
 #define PORT_SUNSAB	39
 
+/* Nuvoton UART */
+#define PORT_NPCM	40
+
 /* Intel EG20 */
 #define PORT_PCH_8LINE	44
 #define PORT_PCH_2LINE	45