Commit f7e290fb authored by Martin Blumenstingl's avatar Martin Blumenstingl Committed by David S. Miller

net: phy: icplus: implement .did_interrupt for IP101A/G

The IP101A_G_IRQ_CONF_STATUS register has bits to detect which
interrupts have fired. Implement the .did_interrupt callback to let the
PHY core know whether the interrupt was for this specific PHY.

This is useful for debugging interrupt problems with 32-pin IP101GR PHYs
where the interrupt line is shared with the RX_ERR (receive error
status) signal. The default values are:
- RX_ERR is enabled by default (LOW means that there is no receive
  error)
- the PHY's interrupt line is configured "active low" by default

Without any additional changes there is a flood of interrupts if the
RX_ERR/INTR32 signal is configured in RX_ERR mode (which is the
default). Having a did_interrupt ensures that the PHY core returns
IRQ_NONE instead of endlessly triggering the PHY state machine.
Additionally the kernel will report this after a while:
  irq 28: nobody cared (try booting with the "irqpoll" option)
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent a872c388
......@@ -44,6 +44,9 @@ MODULE_LICENSE("GPL");
#define IP101A_G_IRQ_CONF_STATUS 0x11 /* Conf Info IRQ & Status Reg */
#define IP101A_G_IRQ_PIN_USED BIT(15) /* INTR pin used */
#define IP101A_G_IRQ_ALL_MASK BIT(11) /* IRQ's inactive */
#define IP101A_G_IRQ_SPEED_CHANGE BIT(2)
#define IP101A_G_IRQ_DUPLEX_CHANGE BIT(1)
#define IP101A_G_IRQ_LINK_CHANGE BIT(0)
static int ip175c_config_init(struct phy_device *phydev)
{
......@@ -209,6 +212,18 @@ static int ip101a_g_config_intr(struct phy_device *phydev)
return phy_write(phydev, IP101A_G_IRQ_CONF_STATUS, val);
}
static int ip101a_g_did_interrupt(struct phy_device *phydev)
{
int val = phy_read(phydev, IP101A_G_IRQ_CONF_STATUS);
if (val < 0)
return 0;
return val & (IP101A_G_IRQ_SPEED_CHANGE |
IP101A_G_IRQ_DUPLEX_CHANGE |
IP101A_G_IRQ_LINK_CHANGE);
}
static int ip101a_g_ack_interrupt(struct phy_device *phydev)
{
int err = phy_read(phydev, IP101A_G_IRQ_CONF_STATUS);
......@@ -243,6 +258,7 @@ static struct phy_driver icplus_driver[] = {
.phy_id_mask = 0x0ffffff0,
.features = PHY_BASIC_FEATURES,
.config_intr = ip101a_g_config_intr,
.did_interrupt = ip101a_g_did_interrupt,
.ack_interrupt = ip101a_g_ack_interrupt,
.config_init = &ip101a_g_config_init,
.suspend = genphy_suspend,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment