macintosh/via-macii: Poll the device most likely to respond

Poll the most recently polled device by default, rather than the lowest
device address that happens to be enabled in autopoll_devs. This improves
input latency. Re-use macii_queue_poll() rather than duplicate that logic.
This eliminates a static struct and function.

Fixes: d95fd5fc ("m68k: Mac II ADB fixes") # v5.0+
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/5836f80886ebcfbe5be5fb7e0dc49feed6469712.1593318192.git.fthain@telegraphics.com.au

drivers/macintosh/via-macii.c

@@ -77,6 +77,10 @@ static volatile unsigned char *via;
 #define ST_ODD		0x20		/* ADB state: odd data byte */
 #define ST_IDLE		0x30		/* ADB state: idle, nothing to send */
 
+/* ADB command byte structure */
+#define ADDR_MASK	0xF0
+#define CMD_MASK	0x0F
+
 static int macii_init_via(void);
 static void macii_start(void);
 static irqreturn_t macii_interrupt(int irq, void *arg);
@@ -117,7 +121,8 @@ static int reply_len; /* number of bytes received in reply_buf or req->reply */
 static int status;          /* VIA's ADB status bits captured upon interrupt */
 static int last_status;              /* status bits as at previous interrupt */
 static int srq_asserted;     /* have to poll for the device that asserted it */
-static int command_byte;         /* the most recent command byte transmitted */
+static u8 last_cmd;              /* the most recent command byte transmitted */
+static u8 last_poll_cmd; /* the most recent Talk R0 command byte transmitted */
 static int autopoll_devs;      /* bits set are device addresses to be polled */
 
 /* Check for MacII style ADB */
@@ -179,35 +184,49 @@ static int macii_init_via(void)
 /* Send an ADB poll (Talk Register 0 command prepended to the request queue) */
 static void macii_queue_poll(void)
 {
-	/* No point polling the active device as it will never assert SRQ, so
-	 * poll the next device in the autopoll list. This could leave us
-	 * stuck in a polling loop if an unprobed device is asserting SRQ.
-	 * In theory, that could only happen if a device was plugged in after
-	 * probing started. Unplugging it again will break the cycle.
-	 * (Simply polling the next higher device often ends up polling almost
-	 * every device (after wrapping around), which takes too long.)
-	 */
-	int device_mask;
-	int next_device;
 	static struct adb_request req;
+	unsigned char poll_command;
+	unsigned int poll_addr;
 
+	/* This only polls devices in the autopoll list, which assumes that
+	 * unprobed devices never assert SRQ. That could happen if a device was
+	 * plugged in after the adb bus scan. Unplugging it again will resolve
+	 * the problem. This behaviour is similar to MacOS.
+	 */
 	if (!autopoll_devs)
 		return;
 
-	device_mask = (1 << (((command_byte & 0xF0) >> 4) + 1)) - 1;
-	if (autopoll_devs & ~device_mask)
-		next_device = ffs(autopoll_devs & ~device_mask) - 1;
-	else
-		next_device = ffs(autopoll_devs) - 1;
+	/* The device most recently polled may not be the best device to poll
+	 * right now. Some other device(s) may have signalled SRQ (the active
+	 * device won't do that). Or the autopoll list may have been changed.
+	 * Try polling the next higher address.
+	 */
+	poll_addr = (last_poll_cmd & ADDR_MASK) >> 4;
+	if ((srq_asserted && last_cmd == last_poll_cmd) ||
+	    !(autopoll_devs & (1 << poll_addr))) {
+		unsigned int higher_devs;
+
+		higher_devs = autopoll_devs & -(1 << (poll_addr + 1));
+		poll_addr = ffs(higher_devs ? higher_devs : autopoll_devs) - 1;
+	}
 
-	adb_request(&req, NULL, ADBREQ_NOSEND, 1, ADB_READREG(next_device, 0));
+	/* Send a Talk Register 0 command */
+	poll_command = ADB_READREG(poll_addr, 0);
+
+	/* No need to repeat this Talk command. The transceiver will do that
+	 * as long as it is idle.
+	 */
+	if (poll_command == last_cmd)
+		return;
+
+	adb_request(&req, NULL, ADBREQ_NOSEND, 1, poll_command);
 
 	req.sent = 0;
 	req.complete = 0;
 	req.reply_len = 0;
 	req.next = current_req;
 
-	if (current_req != NULL) {
+	if (WARN_ON(current_req)) {
 		current_req = &req;
 	} else {
 		current_req = &req;
@@ -266,37 +285,22 @@ static int macii_write(struct adb_request *req)
 /* Start auto-polling */
 static int macii_autopoll(int devs)
 {
-	static struct adb_request req;
 	unsigned long flags;
-	int err = 0;
 
 	local_irq_save(flags);
 
 	/* bit 1 == device 1, and so on. */
 	autopoll_devs = devs & 0xFFFE;
 
-	if (autopoll_devs && !current_req) {
-		/* Send a Talk Reg 0. The controller will repeatedly transmit
-		 * this as long as it is idle.
-		 */
-		adb_request(&req, NULL, ADBREQ_NOSEND, 1,
-		            ADB_READREG(ffs(autopoll_devs) - 1, 0));
-		err = macii_write(&req);
+	if (!current_req) {
+		macii_queue_poll();
+		if (current_req && macii_state == idle)
+			macii_start();
 	}
 
 	local_irq_restore(flags);
-	return err;
-}
 
-static inline int need_autopoll(void)
-{
-	/* Was the last command Talk Reg 0
-	 * and is the target on the autopoll list?
-	 */
-	if ((command_byte & 0x0F) == 0x0C &&
-	    ((1 << ((command_byte & 0xF0) >> 4)) & autopoll_devs))
-		return 0;
-	return 1;
+	return 0;
 }
 
 /* Prod the chip without interrupts */
@@ -333,7 +337,12 @@ static void macii_start(void)
 	 */
 
 	/* store command byte */
-	command_byte = req->data[1];
+	last_cmd = req->data[1];
+
+	/* If this is a Talk Register 0 command, store the command byte */
+	if ((last_cmd & CMD_MASK) == ADB_READREG(0, 0))
+		last_poll_cmd = last_cmd;
+
 	/* Output mode */
 	via[ACR] |= SR_OUT;
 	/* Load data */
@@ -424,10 +433,11 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 				if (req->done)
 					(*req->done)(req);
 
-				if (current_req)
+				if (!current_req)
+					macii_queue_poll();
+
+				if (current_req && macii_state == idle)
 					macii_start();
-				else if (need_autopoll())
-					macii_autopoll(autopoll_devs);
 			}
 
 			if (macii_state == idle) {
@@ -507,14 +517,11 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 
 		macii_state = idle;
 
-		/* SRQ seen before, initiate poll now */
-		if (srq_asserted)
+		if (!current_req)
 			macii_queue_poll();
 
 		if (current_req)
 			macii_start();
-		else if (need_autopoll())
-			macii_autopoll(autopoll_devs);
 
 		if (macii_state == idle)
 			via[B] = (via[B] & ~ST_MASK) | ST_IDLE;