Commit fa62e10d authored by Linus Walleij's avatar Linus Walleij Committed by Stephen Boyd

clk: versatile/icst: support for AP baseboard clocks

This adds support for the two ICST525-based clocks on the
Integrator/AP baseboard, as documented in the board manual
"Integrator/AP ASIC Development Motherboard", ARM DUI0098 B,
pages 3-15 thru 3-18.

Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
[sboyd@codeaurora.org: fixed uninitialized val warning]
Signed-off-by: default avatarStephen Boyd <sboyd@codeaurora.org>
parent 74002fcd
......@@ -29,15 +29,20 @@
#define VERSATILE_AUX_OSC_BITS 0x7FFFF
#define INTEGRATOR_AP_CM_BITS 0xFF
#define INTEGRATOR_AP_SYS_BITS 0xFF
#define INTEGRATOR_CP_CM_CORE_BITS 0x7FF
#define INTEGRATOR_CP_CM_MEM_BITS 0x7FF000
#define INTEGRATOR_AP_PCI_25_33_MHZ BIT(8)
/**
* enum icst_control_type - the type of ICST control register
*/
enum icst_control_type {
ICST_VERSATILE, /* The standard type, all control bits available */
ICST_INTEGRATOR_AP_CM, /* Only 8 bits of VDW available */
ICST_INTEGRATOR_AP_SYS, /* Only 8 bits of VDW available */
ICST_INTEGRATOR_AP_PCI, /* Odd bit pattern storage */
ICST_INTEGRATOR_CP_CM_CORE, /* Only 8 bits of VDW and 3 bits of OD */
ICST_INTEGRATOR_CP_CM_MEM, /* Only 8 bits of VDW and 3 bits of OD */
};
......@@ -92,6 +97,38 @@ static int vco_get(struct clk_icst *icst, struct icst_vco *vco)
return 0;
}
/*
* The Integrator/AP system clock on the base board can only
* access the low eight bits of the v PLL divider. Bit 8 is tied low
* and always zero, r is hardwired to 46, and the output divider is
* hardwired to 3 (divide by 4) according to the document
* "Integrator AP ASIC Development Motherboard" ARM DUI 0098B,
* page 3-16.
*/
if (icst->ctype == ICST_INTEGRATOR_AP_SYS) {
vco->v = val & INTEGRATOR_AP_SYS_BITS;
vco->r = 46;
vco->s = 3;
return 0;
}
/*
* The Integrator/AP PCI clock is using an odd pattern to create
* the child clock, basically a single bit called DIVX/Y is used
* to select between two different hardwired values: setting the
* bit to 0 yields v = 17, r = 22 and OD = 1, whereas setting the
* bit to 1 yields v = 14, r = 14 and OD = 1 giving the frequencies
* 33 or 25 MHz respectively.
*/
if (icst->ctype == ICST_INTEGRATOR_AP_PCI) {
bool divxy = !!(val & INTEGRATOR_AP_PCI_25_33_MHZ);
vco->v = divxy ? 17 : 14;
vco->r = divxy ? 22 : 14;
vco->s = 1;
return 0;
}
/*
* The Integrator/CP core clock can access the low eight bits
* of the v PLL divider. Bit 8 is tied low and always zero,
......@@ -143,6 +180,16 @@ static int vco_set(struct clk_icst *icst, struct icst_vco vco)
if (vco.r != 22)
pr_err("ICST error: tried to use RDW != 22\n");
break;
case ICST_INTEGRATOR_AP_SYS:
mask = INTEGRATOR_AP_SYS_BITS;
val = vco.v & 0xFF;
if (vco.v & 0x100)
pr_err("ICST error: tried to set bit 8 of VDW\n");
if (vco.s != 3)
pr_err("ICST error: tried to use VOD != 1\n");
if (vco.r != 46)
pr_err("ICST error: tried to use RDW != 22\n");
break;
case ICST_INTEGRATOR_CP_CM_CORE:
mask = INTEGRATOR_CP_CM_CORE_BITS; /* Uses 12 bits */
val = (vco.v & 0xFF) | vco.s << 8;
......@@ -225,6 +272,27 @@ static long icst_round_rate(struct clk_hw *hw, unsigned long rate,
return DIV_ROUND_CLOSEST(rate, 500000) * 500000;
}
if (icst->ctype == ICST_INTEGRATOR_AP_SYS) {
/* Divides between 3 and 50 MHz in steps of 0.25 MHz */
if (rate <= 3000000)
return 3000000;
if (rate >= 50000000)
return 5000000;
/* Slam to closest 0.25 MHz */
return DIV_ROUND_CLOSEST(rate, 250000) * 250000;
}
if (icst->ctype == ICST_INTEGRATOR_AP_PCI) {
/*
* If we're below or less than halfway from 25 to 33 MHz
* select 25 MHz
*/
if (rate <= 25000000 || rate < 29000000)
return 25000000;
/* Else just return the default frequency */
return 33000000;
}
vco = icst_hz_to_vco(icst->params, rate);
return icst_hz(icst->params, vco);
}
......@@ -235,6 +303,36 @@ static int icst_set_rate(struct clk_hw *hw, unsigned long rate,
struct clk_icst *icst = to_icst(hw);
struct icst_vco vco;
if (icst->ctype == ICST_INTEGRATOR_AP_PCI) {
/* This clock is especially primitive */
unsigned int val;
int ret;
if (rate == 25000000) {
val = 0;
} else if (rate == 33000000) {
val = INTEGRATOR_AP_PCI_25_33_MHZ;
} else {
pr_err("ICST: cannot set PCI frequency %lu\n",
rate);
return -EINVAL;
}
ret = regmap_write(icst->map, icst->lockreg_off,
VERSATILE_LOCK_VAL);
if (ret)
return ret;
ret = regmap_update_bits(icst->map, icst->vcoreg_off,
INTEGRATOR_AP_PCI_25_33_MHZ,
val);
if (ret)
return ret;
/* This locks the VCO again */
ret = regmap_write(icst->map, icst->lockreg_off, 0);
if (ret)
return ret;
return 0;
}
if (parent_rate)
icst->params->ref = parent_rate;
vco = icst_hz_to_vco(icst->params, rate);
......@@ -368,6 +466,34 @@ static const struct icst_params icst525_apcp_cm_params = {
.idx2s = icst525_idx2s,
};
static const struct icst_params icst525_ap_sys_params = {
.vco_max = ICST525_VCO_MAX_5V,
.vco_min = ICST525_VCO_MIN,
/* Minimum 3 MHz, VDW = 4 */
.vd_min = 3,
/* Maximum 50 MHz, VDW = 192 */
.vd_max = 50,
/* r is hardcoded to 46 and this is the actual divisor, +2 */
.rd_min = 48,
.rd_max = 48,
.s2div = icst525_s2div,
.idx2s = icst525_idx2s,
};
static const struct icst_params icst525_ap_pci_params = {
.vco_max = ICST525_VCO_MAX_5V,
.vco_min = ICST525_VCO_MIN,
/* Minimum 25 MHz */
.vd_min = 25,
/* Maximum 33 MHz */
.vd_max = 33,
/* r is hardcoded to 14 or 22 and this is the actual divisors +2 */
.rd_min = 16,
.rd_max = 24,
.s2div = icst525_s2div,
.idx2s = icst525_idx2s,
};
static void __init of_syscon_icst_setup(struct device_node *np)
{
struct device_node *parent;
......@@ -408,6 +534,12 @@ static void __init of_syscon_icst_setup(struct device_node *np)
} else if (of_device_is_compatible(np, "arm,syscon-icst525-integratorap-cm")) {
icst_desc.params = &icst525_apcp_cm_params;
ctype = ICST_INTEGRATOR_AP_CM;
} else if (of_device_is_compatible(np, "arm,syscon-icst525-integratorap-sys")) {
icst_desc.params = &icst525_ap_sys_params;
ctype = ICST_INTEGRATOR_AP_SYS;
} else if (of_device_is_compatible(np, "arm,syscon-icst525-integratorap-pci")) {
icst_desc.params = &icst525_ap_pci_params;
ctype = ICST_INTEGRATOR_AP_PCI;
} else if (of_device_is_compatible(np, "arm,syscon-icst525-integratorcp-cm-core")) {
icst_desc.params = &icst525_apcp_cm_params;
ctype = ICST_INTEGRATOR_CP_CM_CORE;
......@@ -437,6 +569,10 @@ CLK_OF_DECLARE(arm_syscon_icst307_clk,
"arm,syscon-icst307", of_syscon_icst_setup);
CLK_OF_DECLARE(arm_syscon_integratorap_cm_clk,
"arm,syscon-icst525-integratorap-cm", of_syscon_icst_setup);
CLK_OF_DECLARE(arm_syscon_integratorap_sys_clk,
"arm,syscon-icst525-integratorap-sys", of_syscon_icst_setup);
CLK_OF_DECLARE(arm_syscon_integratorap_pci_clk,
"arm,syscon-icst525-integratorap-pci", of_syscon_icst_setup);
CLK_OF_DECLARE(arm_syscon_integratorcp_cm_core_clk,
"arm,syscon-icst525-integratorcp-cm-core", of_syscon_icst_setup);
CLK_OF_DECLARE(arm_syscon_integratorcp_cm_mem_clk,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment