staging: brcm80211: Remove BUSTYPE macro

BUSTYPE isn't used in this configuration.
Signed-off-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/staging/brcm80211/include/bcmdefs.h

@@ -51,7 +51,6 @@
 #define SPI_BUS			6	/* gSPI target */
 #define RPC_BUS			7	/* RPC target */
 
-#define BUSTYPE(bus) 	(bus)
 #define CHIPTYPE(bus) 	(bus)
 #define CHIPID(chip)	(chip)
 #define CHIPREV(rev)	(rev)

drivers/staging/brcm80211/include/nicpci.h

@@ -74,6 +74,6 @@ extern bool pcicore_pmecap_fast(struct osl_info *osh);
 extern void pcicore_pmeen(void *pch);
 extern void pcicore_pmeclr(void *pch);
 extern bool pcicore_pmestat(void *pch);
-#endif				/* defined(BCMSDIO) || (defined(BCMBUSTYPE) && (BCMBUSTYPE == SI_BUS)) */
+#endif /* defined(BCMSDIO)||(defined(BCMBUSTYPE) && (BCMBUSTYPE==SI_BUS)) */
 
 #endif				/* _NICPCI_H */

drivers/staging/brcm80211/include/siutils.h

@@ -295,9 +295,9 @@ typedef struct si_info {
 #define	ILP_DIV_5MHZ		0	/* ILP = 5 MHz */
 #define	ILP_DIV_1MHZ		4	/* ILP = 1 MHz */
 
-#define PCI(si)		((BUSTYPE((si)->pub.bustype) == PCI_BUS) &&	\
+#define PCI(si)		(((si)->pub.bustype == PCI_BUS) &&	\
 			 ((si)->pub.buscoretype == PCI_CORE_ID))
-#define PCIE(si)	((BUSTYPE((si)->pub.bustype) == PCI_BUS) &&	\
+#define PCIE(si)	(((si)->pub.bustype == PCI_BUS) &&	\
 			 ((si)->pub.buscoretype == PCIE_CORE_ID))
 #define PCI_FORCEHT(si)	\
 	(PCIE(si) && (si->pub.chip == BCM4716_CHIP_ID))

drivers/staging/brcm80211/phy/wlc_phy_cmn.c

@@ -300,7 +300,7 @@ void write_radio_reg(phy_info_t *pi, u16 addr, u16 val)
 		W_REG(osh, &pi->regs->phy4wdatalo, val);
 	}
 
-	if (BUSTYPE(pi->sh->bustype) == PCI_BUS) {
+	if (pi->sh->bustype == PCI_BUS) {
 		if (++pi->phy_wreg >= pi->phy_wreg_limit) {
 			(void)R_REG(osh, &pi->regs->maccontrol);
 			pi->phy_wreg = 0;
@@ -445,7 +445,7 @@ void write_phy_reg(phy_info_t *pi, u16 addr, u16 val)
 #else
 	W_REG(osh, (volatile u32 *)(&regs->phyregaddr),
 	      addr | (val << 16));
-	if (BUSTYPE(pi->sh->bustype) == PCI_BUS) {
+	if (pi->sh->bustype == PCI_BUS) {
 		if (++pi->phy_wreg >= pi->phy_wreg_limit) {
 			pi->phy_wreg = 0;
 			(void)R_REG(osh, &regs->phyversion);

drivers/staging/brcm80211/phy/wlc_phy_int.h

@@ -1158,7 +1158,7 @@ extern void wlc_phy_table_write_nphy(phy_info_t *pi, u32, u32, u32,
 	 (pi->ipa5g_on && CHSPEC_IS5G(pi->radio_chanspec)))
 
 #define WLC_PHY_WAR_PR51571(pi) \
-	if ((BUSTYPE((pi)->sh->bustype) == PCI_BUS) && NREV_LT((pi)->pubpi.phy_rev, 3)) \
+	if (((pi)->sh->bustype == PCI_BUS) && NREV_LT((pi)->pubpi.phy_rev, 3)) \
 		(void)R_REG((pi)->sh->osh, &(pi)->regs->maccontrol)
 
 extern void wlc_phy_cal_perical_nphy_run(phy_info_t *pi, u8 caltype);

drivers/staging/brcm80211/sys/wl_mac80211.c

@@ -1305,8 +1305,8 @@ void wl_free(wl_info_t *wl)
 	 * unregister_netdev() calls get_stats() which may read chip registers
 	 * so we cannot unmap the chip registers until after calling unregister_netdev() .
 	 */
-	if (wl->regsva && BUSTYPE(wl->bcm_bustype) != SDIO_BUS &&
-	    BUSTYPE(wl->bcm_bustype) != JTAG_BUS) {
+	if (wl->regsva && wl->bcm_bustype != SDIO_BUS &&
+	    wl->bcm_bustype != JTAG_BUS) {
 		iounmap((void *)wl->regsva);
 	}
 	wl->regsva = NULL;

drivers/staging/brcm80211/sys/wlc_bmac.c

@@ -832,7 +832,7 @@ int wlc_bmac_attach(wlc_info_t *wlc, u16 vendor, u16 device, uint unit,
 	    || (wlc_hw->boardflags & BFL_NOPLLDOWN))
 		wlc_bmac_pllreq(wlc_hw, true, WLC_PLLREQ_SHARED);
 
-	if ((BUSTYPE(wlc_hw->sih->bustype) == PCI_BUS)
+	if ((wlc_hw->sih->bustype == PCI_BUS)
 	    && (si_pci_war16165(wlc_hw->sih)))
 		wlc->war16165 = true;
 
@@ -992,7 +992,7 @@ int wlc_bmac_attach(wlc_info_t *wlc, u16 vendor, u16 device, uint unit,
 	wlc_coredisable(wlc_hw);
 
 	/* Match driver "down" state */
-	if (BUSTYPE(wlc_hw->sih->bustype) == PCI_BUS)
+	if (wlc_hw->sih->bustype == PCI_BUS)
 		si_pci_down(wlc_hw->sih);
 
 	/* register sb interrupt callback functions */
@@ -1081,7 +1081,7 @@ int wlc_bmac_detach(wlc_info_t *wlc)
 		 */
 		si_deregister_intr_callback(wlc_hw->sih);
 
-		if (BUSTYPE(wlc_hw->sih->bustype) == PCI_BUS)
+		if (wlc_hw->sih->bustype == PCI_BUS)
 			si_pci_sleep(wlc_hw->sih);
 	}
 
@@ -1207,7 +1207,7 @@ int wlc_bmac_up_prep(wlc_hw_info_t *wlc_hw)
 	 */
 	coremask = (1 << wlc_hw->wlc->core->coreidx);
 
-	if (BUSTYPE(wlc_hw->sih->bustype) == PCI_BUS)
+	if (wlc_hw->sih->bustype == PCI_BUS)
 		si_pci_setup(wlc_hw->sih, coremask);
 
 	ASSERT(si_coreid(wlc_hw->sih) == D11_CORE_ID);
@@ -1218,13 +1218,13 @@ int wlc_bmac_up_prep(wlc_hw_info_t *wlc_hw)
 	 */
 	if (wlc_bmac_radio_read_hwdisabled(wlc_hw)) {
 		/* put SB PCI in down state again */
-		if (BUSTYPE(wlc_hw->sih->bustype) == PCI_BUS)
+		if (wlc_hw->sih->bustype == PCI_BUS)
 			si_pci_down(wlc_hw->sih);
 		wlc_bmac_xtal(wlc_hw, OFF);
 		return BCME_RADIOOFF;
 	}
 
-	if (BUSTYPE(wlc_hw->sih->bustype) == PCI_BUS)
+	if (wlc_hw->sih->bustype == PCI_BUS)
 		si_pci_up(wlc_hw->sih);
 
 	/* reset the d11 core */
@@ -1310,7 +1310,7 @@ int wlc_bmac_down_finish(wlc_hw_info_t *wlc_hw)
 
 		/* turn off primary xtal and pll */
 		if (!wlc_hw->noreset) {
-			if (BUSTYPE(wlc_hw->sih->bustype) == PCI_BUS)
+			if (wlc_hw->sih->bustype == PCI_BUS)
 				si_pci_down(wlc_hw->sih);
 			wlc_bmac_xtal(wlc_hw, OFF);
 		}
@@ -2263,7 +2263,7 @@ void wlc_bmac_hw_up(wlc_hw_info_t *wlc_hw)
 	si_clkctl_init(wlc_hw->sih);
 	wlc_clkctl_clk(wlc_hw, CLK_FAST);
 
-	if (BUSTYPE(wlc_hw->sih->bustype) == PCI_BUS) {
+	if (wlc_hw->sih->bustype == PCI_BUS) {
 		si_pci_fixcfg(wlc_hw->sih);
 
 		/* AI chip doesn't restore bar0win2 on hibernation/resume, need sw fixup */
@@ -4123,8 +4123,8 @@ void wlc_gpio_fast_deinit(wlc_hw_info_t *wlc_hw)
 	/* Only chips with internal bus or PCIE cores or certain PCI cores
 	 * are able to switch cores w/o disabling interrupts
 	 */
-	if (!((BUSTYPE(wlc_hw->sih->bustype) == SI_BUS) ||
-	      ((BUSTYPE(wlc_hw->sih->bustype) == PCI_BUS) &&
+	if (!((wlc_hw->sih->bustype == SI_BUS) ||
+	      ((wlc_hw->sih->bustype == PCI_BUS) &&
 	       ((wlc_hw->sih->buscoretype == PCIE_CORE_ID) ||
 		(wlc_hw->sih->buscorerev >= 13)))))
 		return;

drivers/staging/brcm80211/sys/wlc_mac80211.c

@@ -92,7 +92,7 @@
 /* To inform the ucode of the last mcast frame posted so that it can clear moredata bit */
 #define BCMCFID(wlc, fid) wlc_bmac_write_shm((wlc)->hw, M_BCMC_FID, (fid))
 
-#define WLC_WAR16165(wlc) (BUSTYPE(wlc->pub->sih->bustype) == PCI_BUS && \
+#define WLC_WAR16165(wlc) (wlc->pub->sih->bustype == PCI_BUS && \
 				(!AP_ENAB(wlc->pub)) && (wlc->war16165))
 
 /* debug/trace */

drivers/staging/brcm80211/util/aiutils.c

@@ -119,7 +119,7 @@ void ai_scan(si_t *sih, void *regs, uint devid)
 
 	erombase = R_REG(sii->osh, &cc->eromptr);
 
-	switch (BUSTYPE(sih->bustype)) {
+	switch (sih->bustype) {
 	case SI_BUS:
 		eromptr = (u32 *) REG_MAP(erombase, SI_CORE_SIZE);
 		break;
@@ -334,7 +334,7 @@ void *ai_setcoreidx(si_t *sih, uint coreidx)
 	ASSERT((sii->intrsenabled_fn == NULL)
 	       || !(*(sii)->intrsenabled_fn) ((sii)->intr_arg));
 
-	switch (BUSTYPE(sih->bustype)) {
+	switch (sih->bustype) {
 	case SI_BUS:
 		/* map new one */
 		if (!sii->regs[coreidx]) {
@@ -508,7 +508,7 @@ uint ai_corereg(si_t *sih, uint coreidx, uint regoff, uint mask, uint val)
 	if (coreidx >= SI_MAXCORES)
 		return 0;
 
-	if (BUSTYPE(sih->bustype) == SI_BUS) {
+	if (sih->bustype == SI_BUS) {
 		/* If internal bus, we can always get at everything */
 		fast = true;
 		/* map if does not exist */
@@ -518,7 +518,7 @@ uint ai_corereg(si_t *sih, uint coreidx, uint regoff, uint mask, uint val)
 			ASSERT(GOODREGS(sii->regs[coreidx]));
 		}
 		r = (u32 *) ((unsigned char *) sii->regs[coreidx] + regoff);
-	} else if (BUSTYPE(sih->bustype) == PCI_BUS) {
+	} else if (sih->bustype == PCI_BUS) {
 		/* If pci/pcie, we can get at pci/pcie regs and on newer cores to chipc */
 
 		if ((sii->coreid[coreidx] == CC_CORE_ID) && SI_FAST(sii)) {

drivers/staging/brcm80211/util/bcmsrom.c

@@ -164,14 +164,14 @@ int srom_var_init(si_t *sih, uint bustype, void *curmap, struct osl_info *osh,
 
 	len = 0;
 
-	ASSERT(bustype == BUSTYPE(bustype));
+	ASSERT(bustype == bustype);
 	if (vars == NULL || count == NULL)
 		return 0;
 
 	*vars = NULL;
 	*count = 0;
 
-	switch (BUSTYPE(bustype)) {
+	switch (bustype) {
 	case SI_BUS:
 	case JTAG_BUS:
 		return initvars_srom_si(sih, osh, curmap, vars, count);
@@ -204,7 +204,7 @@ srom_read(si_t *sih, uint bustype, void *curmap, struct osl_info *osh,
 	uint i;
 #endif				/* BCMSDIO */
 
-	ASSERT(bustype == BUSTYPE(bustype));
+	ASSERT(bustype == bustype);
 
 	/* check input - 16-bit access only */
 	if (byteoff & 1 || nbytes & 1 || (byteoff + nbytes) > SROM_MAX)
@@ -213,7 +213,7 @@ srom_read(si_t *sih, uint bustype, void *curmap, struct osl_info *osh,
 	off = byteoff / 2;
 	nw = nbytes / 2;
 
-	if (BUSTYPE(bustype) == PCI_BUS) {
+	if (bustype == PCI_BUS) {
 		if (!curmap)
 			return 1;
 
@@ -235,7 +235,7 @@ srom_read(si_t *sih, uint bustype, void *curmap, struct osl_info *osh,
 		}
 #endif
 #ifdef BCMSDIO
-	} else if (BUSTYPE(bustype) == SDIO_BUS) {
+	} else if (bustype == SDIO_BUS) {
 		off = byteoff / 2;
 		nw = nbytes / 2;
 		for (i = 0; i < nw; i++) {
@@ -244,7 +244,7 @@ srom_read(si_t *sih, uint bustype, void *curmap, struct osl_info *osh,
 				return 1;
 		}
 #endif				/* BCMSDIO */
-	} else if (BUSTYPE(bustype) == SI_BUS) {
+	} else if (bustype == SI_BUS) {
 		return 1;
 	} else {
 		return 1;

drivers/staging/brcm80211/util/hnddma.c

@@ -2666,8 +2666,8 @@ uint dma_addrwidth(si_t *sih, void *dmaregs)
 		/* backplane are 64-bit capable */
 		if (si_backplane64(sih))
 			/* If bus is System Backplane or PCIE then we can access 64-bits */
-			if ((BUSTYPE(sih->bustype) == SI_BUS) ||
-			    ((BUSTYPE(sih->bustype) == PCI_BUS) &&
+			if ((sih->bustype == SI_BUS) ||
+			    ((sih->bustype == PCI_BUS) &&
 			     (sih->buscoretype == PCIE_CORE_ID)))
 				return DMADDRWIDTH_64;
 
@@ -2681,8 +2681,8 @@ uint dma_addrwidth(si_t *sih, void *dmaregs)
 	dma32regs = (dma32regs_t *) dmaregs;
 
 	/* For System Backplane, PCIE bus or addrext feature, 32-bits ok */
-	if ((BUSTYPE(sih->bustype) == SI_BUS) ||
-	    ((BUSTYPE(sih->bustype) == PCI_BUS)
+	if ((sih->bustype == SI_BUS) ||
+	    ((sih->bustype == PCI_BUS)
 	     && sih->buscoretype == PCIE_CORE_ID)
 	    || (_dma32_addrext(osh, dma32regs)))
 		return DMADDRWIDTH_32;

drivers/staging/brcm80211/util/nicpci.c

@@ -47,7 +47,8 @@ typedef struct {
 
 /* debug/trace */
 #define	PCI_ERROR(args)
-#define PCIE_PUB(sih) ((BUSTYPE((sih)->bustype) == PCI_BUS) && ((sih)->buscoretype == PCIE_CORE_ID))
+#define PCIE_PUB(sih) \
+	(((sih)->bustype == PCI_BUS) && ((sih)->buscoretype == PCIE_CORE_ID))
 
 /* routines to access mdio slave device registers */
 static bool pcie_mdiosetblock(pcicore_info_t *pi, uint blk);

drivers/staging/brcm80211/util/sbutils.c

@@ -90,7 +90,7 @@ static u32 _sb_coresba(si_info_t *sii)
 {
 	u32 sbaddr = 0;
 
-	switch (BUSTYPE(sii->pub.bustype)) {
+	switch (sii->pub.bustype) {
 	case SPI_BUS:
 	case SDIO_BUS:
 		sbaddr = (u32)(unsigned long)sii->curmap;
@@ -347,7 +347,7 @@ static void *_sb_setcoreidx(si_info_t *sii, uint coreidx)
 	u32 sbaddr = sii->coresba[coreidx];
 	void *regs;
 
-	switch (BUSTYPE(sii->pub.bustype)) {
+	switch (sii->pub.bustype) {
 #ifdef BCMSDIO
 	case SPI_BUS:
 	case SDIO_BUS:
@@ -412,8 +412,8 @@ bool sb_taclear(si_t *sih, bool details)
 
 	sii = SI_INFO(sih);
 
-	if ((BUSTYPE(sii->pub.bustype) == SDIO_BUS) ||
-	    (BUSTYPE(sii->pub.bustype) == SPI_BUS)) {
+	if ((sii->pub.bustype == SDIO_BUS) ||
+	    (sii->pub.bustype == SPI_BUS)) {
 
 		INTR_OFF(sii, intr_val);
 		origidx = si_coreidx(sih);

drivers/staging/brcm80211/util/siutils.c

@@ -117,12 +117,12 @@ static bool si_buscore_prep(si_info_t *sii, uint bustype, uint devid,
 
 #ifndef BRCM_FULLMAC
 	/* kludge to enable the clock on the 4306 which lacks a slowclock */
-	if (BUSTYPE(bustype) == PCI_BUS && !si_ispcie(sii))
+	if (bustype == PCI_BUS && !si_ispcie(sii))
 		si_clkctl_xtal(&sii->pub, XTAL | PLL, ON);
 #endif
 
 #if defined(BCMSDIO)
-	if (BUSTYPE(bustype) == SDIO_BUS) {
+	if (bustype == SDIO_BUS) {
 		int err;
 		u8 clkset;
 
@@ -224,7 +224,7 @@ static bool si_buscore_setup(si_info_t *sii, chipcregs_t *cc, uint bustype,
 		SI_VMSG(("CORE[%d]: id 0x%x rev %d base 0x%x regs 0x%p\n",
 			 i, cid, crev, sii->coresba[i], sii->regs[i]));
 
-		if (BUSTYPE(bustype) == PCI_BUS) {
+		if (bustype == PCI_BUS) {
 			if (cid == PCI_CORE_ID) {
 				pciidx = i;
 				pcirev = crev;
@@ -236,8 +236,8 @@ static bool si_buscore_setup(si_info_t *sii, chipcregs_t *cc, uint bustype,
 			}
 		}
 #ifdef BCMSDIO
-		else if (((BUSTYPE(bustype) == SDIO_BUS) ||
-			  (BUSTYPE(bustype) == SPI_BUS)) &&
+		else if (((bustype == SDIO_BUS) ||
+			  (bustype == SPI_BUS)) &&
 			 ((cid == PCMCIA_CORE_ID) || (cid == SDIOD_CORE_ID))) {
 			sii->pub.buscorerev = crev;
 			sii->pub.buscoretype = cid;
@@ -259,7 +259,7 @@ static bool si_buscore_setup(si_info_t *sii, chipcregs_t *cc, uint bustype,
 	* or downloaded code was
 	* already running.
 	*/
-	if ((BUSTYPE(bustype) == SDIO_BUS) || (BUSTYPE(bustype) == SPI_BUS)) {
+	if ((bustype == SDIO_BUS) || (bustype == SPI_BUS)) {
 		if (si_setcore(&sii->pub, ARM7S_CORE_ID, 0) ||
 			si_setcore(&sii->pub, ARMCM3_CORE_ID, 0))
 			si_core_disable(&sii->pub, 0);
@@ -285,7 +285,7 @@ static bool si_buscore_setup(si_info_t *sii, chipcregs_t *cc, uint bustype,
 		 sii->pub.buscoretype, sii->pub.buscorerev));
 
 	/* fixup necessary chip/core configurations */
-	if (BUSTYPE(sii->pub.bustype) == PCI_BUS) {
+	if (sii->pub.bustype == PCI_BUS) {
 		if (SI_FAST(sii)) {
 			if (!sii->pch) {
 				sii->pch = (void *)pcicore_init(
@@ -312,7 +312,7 @@ static __used void si_nvram_process(si_info_t *sii, char *pvars)
 	uint w = 0;
 
 	/* get boardtype and boardrev */
-	switch (BUSTYPE(sii->pub.bustype)) {
+	switch (sii->pub.bustype) {
 	case PCI_BUS:
 		/* do a pci config read to get subsystem id and subvendor id */
 		pci_read_config_dword(sii->osh->pdev, PCI_CFG_SVID, &w);
@@ -394,11 +394,6 @@ static si_info_t *si_doattach(si_info_t *sii, uint devid, struct osl_info *osh,
 	cc = (chipcregs_t *) sii->curmap;
 	sih->bustype = bustype;
 
-	if (bustype != BUSTYPE(bustype)) {
-		SI_ERROR(("si_doattach: bus type %d does not match configured bus type %d\n", bustype, BUSTYPE(bustype)));
-		return NULL;
-	}
-
 	/* bus/core/clk setup for register access */
 	if (!si_buscore_prep(sii, bustype, devid, sdh)) {
 		SI_ERROR(("si_doattach: si_core_clk_prep failed %d\n",
@@ -448,7 +443,7 @@ static si_info_t *si_doattach(si_info_t *sii, uint devid, struct osl_info *osh,
 
 	/* Init nvram from sprom/otp if they exist */
 	if (srom_var_init
-	    (&sii->pub, BUSTYPE(bustype), regs, sii->osh, vars, varsz)) {
+	    (&sii->pub, bustype, regs, sii->osh, vars, varsz)) {
 		SI_ERROR(("si_doattach: srom_var_init failed: bad srom\n"));
 		goto exit;
 	}
@@ -549,10 +544,6 @@ static si_info_t *si_doattach(si_info_t *sii, uint devid, struct osl_info *osh,
 	}
 
 	sih->bustype = bustype;
-	if (bustype != BUSTYPE(bustype)) {
-		SI_ERROR(("si_doattach: bus type %d does not match configured bus type %d\n", bustype, BUSTYPE(bustype)));
-		return NULL;
-	}
 
 	/* bus/core/clk setup for register access */
 	if (!si_buscore_prep(sii, bustype, devid, sdh)) {
@@ -620,7 +611,7 @@ static si_info_t *si_doattach(si_info_t *sii, uint devid, struct osl_info *osh,
 
 	/* Init nvram from sprom/otp if they exist */
 	if (srom_var_init
-	    (&sii->pub, BUSTYPE(bustype), regs, sii->osh, vars, varsz)) {
+	    (&sii->pub, bustype, regs, sii->osh, vars, varsz)) {
 		SI_ERROR(("si_doattach: srom_var_init failed: bad srom\n"));
 		goto exit;
 	}
@@ -691,7 +682,7 @@ static si_info_t *si_doattach(si_info_t *sii, uint devid, struct osl_info *osh,
 
 	return sii;
  exit:
-	if (BUSTYPE(sih->bustype) == PCI_BUS) {
+	if (sih->bustype == PCI_BUS) {
 		if (sii->pch)
 			pcicore_deinit(sii->pch);
 		sii->pch = NULL;
@@ -715,7 +706,7 @@ void si_detach(si_t *sih)
 	if (sii == NULL)
 		return;
 
-	if (BUSTYPE(sih->bustype) == SI_BUS)
+	if (sih->bustype == SI_BUS)
 		for (idx = 0; idx < SI_MAXCORES; idx++)
 			if (sii->regs[idx]) {
 				REG_UNMAP(sii->regs[idx]);
@@ -725,7 +716,7 @@ void si_detach(si_t *sih)
 #ifndef BRCM_FULLMAC
 	nvram_exit((void *)si_local);	/* free up nvram buffers */
 
-	if (BUSTYPE(sih->bustype) == PCI_BUS) {
+	if (sih->bustype == PCI_BUS) {
 		if (sii->pch)
 			pcicore_deinit(sii->pch);
 		sii->pch = NULL;
@@ -1097,7 +1088,7 @@ static uint si_slowclk_src(si_info_t *sii)
 	ASSERT(SI_FAST(sii) || si_coreid(&sii->pub) == CC_CORE_ID);
 
 	if (sii->pub.ccrev < 6) {
-		if (BUSTYPE(sii->pub.bustype) == PCI_BUS) {
+		if (sii->pub.bustype == PCI_BUS) {
 			pci_read_config_dword(sii->osh->pdev, PCI_GPIO_OUT,
 					      &val);
 			if (val & PCI_CFG_GPIO_SCS)
@@ -1273,7 +1264,7 @@ int si_clkctl_xtal(si_t *sih, uint what, bool on)
 
 	sii = SI_INFO(sih);
 
-	switch (BUSTYPE(sih->bustype)) {
+	switch (sih->bustype) {
 
 #ifdef BCMSDIO
 	case SDIO_BUS:
@@ -1384,7 +1375,7 @@ static bool _si_clkctl_cc(si_info_t *sii, uint mode)
 		INTR_OFF(sii, intr_val);
 		origidx = sii->curidx;
 
-		if ((BUSTYPE(sii->pub.bustype) == SI_BUS) &&
+		if ((sii->pub.bustype == SI_BUS) &&
 		    si_setcore(&sii->pub, MIPS33_CORE_ID, 0) &&
 		    (si_corerev(&sii->pub) <= 7) && (sii->pub.ccrev >= 10))
 			goto done;
@@ -1466,7 +1457,7 @@ int si_devpath(si_t *sih, char *path, int size)
 	if (!path || size <= 0)
 		return -1;
 
-	switch (BUSTYPE(sih->bustype)) {
+	switch (sih->bustype) {
 	case SI_BUS:
 	case JTAG_BUS:
 		slen = snprintf(path, (size_t) size, "sb/%u/", si_coreidx(sih));
@@ -1556,7 +1547,7 @@ static __used bool si_ispcie(si_info_t *sii)
 {
 	u8 cap_ptr;
 
-	if (BUSTYPE(sii->pub.bustype) != PCI_BUS)
+	if (sii->pub.bustype != PCI_BUS)
 		return false;
 
 	cap_ptr =
@@ -1623,7 +1614,7 @@ void si_pci_up(si_t *sih)
 	sii = SI_INFO(sih);
 
 	/* if not pci bus, we're done */
-	if (BUSTYPE(sih->bustype) != PCI_BUS)
+	if (sih->bustype != PCI_BUS)
 		return;
 
 	if (PCI_FORCEHT(sii))
@@ -1652,7 +1643,7 @@ void si_pci_down(si_t *sih)
 	sii = SI_INFO(sih);
 
 	/* if not pci bus, we're done */
-	if (BUSTYPE(sih->bustype) != PCI_BUS)
+	if (sih->bustype != PCI_BUS)
 		return;
 
 	/* release FORCEHT since chip is going to "down" state */
@@ -1675,7 +1666,7 @@ void si_pci_setup(si_t *sih, uint coremask)
 
 	sii = SI_INFO(sih);
 
-	if (BUSTYPE(sii->pub.bustype) != PCI_BUS)
+	if (sii->pub.bustype != PCI_BUS)
 		return;
 
 	ASSERT(PCI(sii) || PCIE(sii));
@@ -1737,7 +1728,7 @@ int si_pci_fixcfg(si_t *sih)
 
 	si_info_t *sii = SI_INFO(sih);
 
-	ASSERT(BUSTYPE(sii->pub.bustype) == PCI_BUS);
+	ASSERT(sii->pub.bustype == PCI_BUS);
 
 	/* Fixup PI in SROM shadow area to enable the correct PCI core access */
 	/* save the current index */
@@ -1783,7 +1774,7 @@ u32 si_gpiocontrol(si_t *sih, u32 mask, u32 val, u8 priority)
 	 * ignore reservation if it's high priority (e.g., test apps)
 	 */
 	if ((priority != GPIO_HI_PRIORITY) &&
-	    (BUSTYPE(sih->bustype) == SI_BUS) && (val || mask)) {
+	    (sih->bustype == SI_BUS) && (val || mask)) {
 		mask = priority ? (si_gpioreservation & mask) :
 		    ((si_gpioreservation | mask) & ~(si_gpioreservation));
 		val &= mask;
@@ -1935,7 +1926,7 @@ bool si_deviceremoved(si_t *sih)
 
 	sii = SI_INFO(sih);
 
-	switch (BUSTYPE(sih->bustype)) {
+	switch (sih->bustype) {
 	case PCI_BUS:
 		ASSERT(sii->osh != NULL);
 		pci_read_config_dword(sii->osh->pdev, PCI_CFG_VID, &w);