Commit fbb9ab10 authored by David Ertman's avatar David Ertman Committed by Jeff Kirsher

e1000e: Expand workaround for 10Mb HD throughput bug

In commit 772d05c5 "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.

This same behavior is seen on i217 and i218 parts as well.  This patch expands
the original workaround to encompass these parts.
Signed-off-by: default avatarDave Ertman <davidx.m.ertman@intel.com>
Tested-by: default avatarAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent 77e61146
...@@ -1314,14 +1314,17 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) ...@@ -1314,14 +1314,17 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
return ret_val; return ret_val;
} }
/* When connected at 10Mbps half-duplex, 82579 parts are excessively /* When connected at 10Mbps half-duplex, some parts are excessively
* aggressive resulting in many collisions. To avoid this, increase * aggressive resulting in many collisions. To avoid this, increase
* the IPG and reduce Rx latency in the PHY. * the IPG and reduce Rx latency in the PHY.
*/ */
if ((hw->mac.type == e1000_pch2lan) && link) { if (((hw->mac.type == e1000_pch2lan) ||
(hw->mac.type == e1000_pch_lpt)) && link) {
u32 reg; u32 reg;
reg = er32(STATUS); reg = er32(STATUS);
if (!(reg & (E1000_STATUS_FD | E1000_STATUS_SPEED_MASK))) { if (!(reg & (E1000_STATUS_FD | E1000_STATUS_SPEED_MASK))) {
u16 emi_addr;
reg = er32(TIPG); reg = er32(TIPG);
reg &= ~E1000_TIPG_IPGT_MASK; reg &= ~E1000_TIPG_IPGT_MASK;
reg |= 0xFF; reg |= 0xFF;
...@@ -1332,8 +1335,12 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) ...@@ -1332,8 +1335,12 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
if (ret_val) if (ret_val)
return ret_val; return ret_val;
ret_val = if (hw->mac.type == e1000_pch2lan)
e1000_write_emi_reg_locked(hw, I82579_RX_CONFIG, 0); emi_addr = I82579_RX_CONFIG;
else
emi_addr = I217_RX_CONFIG;
ret_val = e1000_write_emi_reg_locked(hw, emi_addr, 0);
hw->phy.ops.release(hw); hw->phy.ops.release(hw);
......
...@@ -242,6 +242,7 @@ ...@@ -242,6 +242,7 @@
#define I217_EEE_CAPABILITY 0x8000 /* IEEE MMD Register 3.20 */ #define I217_EEE_CAPABILITY 0x8000 /* IEEE MMD Register 3.20 */
#define I217_EEE_ADVERTISEMENT 0x8001 /* IEEE MMD Register 7.60 */ #define I217_EEE_ADVERTISEMENT 0x8001 /* IEEE MMD Register 7.60 */
#define I217_EEE_LP_ABILITY 0x8002 /* IEEE MMD Register 7.61 */ #define I217_EEE_LP_ABILITY 0x8002 /* IEEE MMD Register 7.61 */
#define I217_RX_CONFIG 0xB20C /* Receive configuration */
#define E1000_EEE_RX_LPI_RCVD 0x0400 /* Tx LP idle received */ #define E1000_EEE_RX_LPI_RCVD 0x0400 /* Tx LP idle received */
#define E1000_EEE_TX_LPI_RCVD 0x0800 /* Rx LP idle received */ #define E1000_EEE_TX_LPI_RCVD 0x0800 /* Rx LP idle received */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment