[PATCH] I2C: remove bus scan logic from i2c chip drivers

This patch drops bus scan from i2c-algo-ite and i2c-ibm_iic. It also
removes the incomplete and broken SLO_IO stuff from i2c-algo-ite.

drivers/i2c/algos/i2c-algo-ite.c

@@ -60,27 +60,13 @@
  	/* debug the protocol by showing transferred bits */
 #define DEF_TIMEOUT 16
 
-/* debugging - slow down transfer to have a look at the data .. 	*/
-/* I use this with two leds&resistors, each one connected to sda,scl 	*/
-/* respectively. This makes sure that the algorithm works. Some chips   */
-/* might not like this, as they have an internal timeout of some mils	*/
-/*
-#define SLO_IO      jif=jiffies;while(jiffies<=jif+i2c_table[minor].veryslow)\
-                        cond_resched();
-*/
-
 
 /* ----- global variables ---------------------------------------------	*/
 
-#ifdef SLO_IO
-	int jif;
-#endif
-
 /* module parameters:
  */
 static int i2c_debug=1;
 static int iic_test=0;	/* see if the line-setting functions work	*/
-static int iic_scan=0;	/* have a look at what's hanging 'round		*/
 
 /* --- setting states on the bus with the right timing: ---------------	*/
 
@@ -757,8 +743,6 @@ static struct i2c_algorithm iic_algo = {
  */
 int i2c_iic_add_bus(struct i2c_adapter *adap)
 {
-	int i;
-	short status;
 	struct i2c_algo_iic_data *iic_adap = adap->algo_data;
 
 	if (iic_test) {
@@ -782,24 +766,6 @@ int i2c_iic_add_bus(struct i2c_adapter *adap)
 	i2c_add_adapter(adap);
 	iic_init(iic_adap);
 
-	/* scan bus */
-	/* By default scanning the bus is turned off. */
-	if (iic_scan) {
-		printk(KERN_INFO " i2c-algo-ite: scanning bus %s.\n",
-		       adap->name);
-		for (i = 0x00; i < 0xff; i+=2) {
-			iic_outw(iic_adap, ITE_I2CSAR, i);
-			iic_start(iic_adap);
-			if ( (wait_for_pin(iic_adap, &status) == 0) && 
-			    ((status & ITE_I2CHSR_DNE) == 0) ) { 
-				printk(KERN_INFO "\n(%02x)\n",i>>1); 
-			} else {
-				printk(KERN_INFO "."); 
-				iic_reset(iic_adap);
-			}
-			udelay(iic_adap->udelay);
-		}
-	}
 	return 0;
 }
 
@@ -839,11 +805,9 @@ MODULE_DESCRIPTION("ITE iic algorithm");
 MODULE_LICENSE("GPL");
 
 MODULE_PARM(iic_test, "i");
-MODULE_PARM(iic_scan, "i");
 MODULE_PARM(i2c_debug,"i");
 
 MODULE_PARM_DESC(iic_test, "Test if the I2C bus is available");
-MODULE_PARM_DESC(iic_scan, "Scan for active chips on the bus");
 MODULE_PARM_DESC(i2c_debug,
         "debug level - 0 off; 1 normal; 2,3 more verbose; 9 iic-protocol");
 

drivers/i2c/busses/i2c-ibm_iic.c

@@ -48,10 +48,6 @@
 MODULE_DESCRIPTION("IBM IIC driver v" DRIVER_VERSION);
 MODULE_LICENSE("GPL");
 
-static int iic_scan = 0;
-MODULE_PARM(iic_scan, "i");
-MODULE_PARM_DESC(iic_scan, "Scan for active chips on the bus");
-
 static int iic_force_poll = 0;
 MODULE_PARM(iic_force_poll, "i");
 MODULE_PARM_DESC(iic_force_poll, "Force polling mode");
@@ -517,32 +513,6 @@ static struct i2c_algorithm iic_algo = {
 	.functionality	= iic_func
 };
 
-/*
- * Scan bus for valid 7-bit addresses (ie things that ACK on 1 byte read)
- * We only scan range [0x08 - 0x77], all other addresses are reserved anyway
- */
-static void __devinit iic_scan_bus(struct ibm_iic_private* dev)
-{
-	int found = 0;
-	char dummy;
-	struct i2c_msg msg = {
-		.buf   = &dummy,
-		.len   = sizeof(dummy),
-		.flags = I2C_M_RD
-	};
-	
-	printk(KERN_INFO "ibm-iic%d: scanning bus...\n" KERN_INFO, dev->idx);
-	
-	for (msg.addr = 8; msg.addr < 0x78; ++msg.addr)
-		if (iic_xfer(&dev->adap, &msg, 1) == 1){
-			++found;
-			printk(" 0x%02x", msg.addr);
-		}
-
-	printk("%sibm-iic%d: %d device(s) detected\n", 
-		found ? "\n" KERN_INFO : "", dev->idx, found);
-}
-
 /*
  * Calculates IICx_CLCKDIV value for a specific OPB clock frequency
  */
@@ -649,10 +619,6 @@ static int __devinit iic_probe(struct ocp_device *ocp){
 	printk(KERN_INFO "ibm-iic%d: using %s mode\n", dev->idx,
 		dev->fast_mode ? "fast (400 kHz)" : "standard (100 kHz)");
 
-	/* Scan bus if requested by user */
-	if (iic_scan)
-		iic_scan_bus(dev);
-
 	return 0;
 
 fail: