- 04 Aug, 2013 29 commits
-
-
Felipe Balbi authored
commit cdcedd69 upstream. In case we fail our ->udc_start() callback, we should be ready to accept another modprobe following the failed one. We had forgotten to clear dwc->gadget_driver back to NULL and, because of that, we were preventing gadget driver modprobe from being retried. Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Huang Rui authored
commit 1974d494 upstream. Per dwc3 2.50a spec, the is_devspec bit is used to distinguish the Device Endpoint-Specific Event or Device-Specific Event (DEVT). If the bit is 1, the event is represented Device-Specific Event, then use [7:1] bits as Device Specific Event to marked the type. It has 7 bits, and we can see the reserved8_31 variable name which means from 8 to 31 bits marked reserved, actually there are 24 bits not 25 bits between that. And 1 + 7 + 24 = 32, the event size is 4 byes. So in dwc3_event_type, the bit mask should be: is_devspec [0] 1 bit type [7:1] 7 bits reserved8_31 [31:8] 24 bits This patch should be backported to kernels as old as 3.2, that contain the commit 72246da4 "usb: Introduce DesignWare USB3 DRD Driver". Signed-off-by:
Huang Rui <ray.huang@amd.com> Signed-off-by:
-
Ruchika Kharwar authored
commit 315955d7 upstream. When there is an error with the usb3_phy probe or absence, the error returned is erroneously for usb2_phy. Signed-off-by:
Ruchika Kharwar <ruchika@ti.com> Signed-off-by:
-
Johan Hovold authored
commit 5f8a2e68 upstream. Allocated urbs and buffers were never freed on errors in open. Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Roger Quadros authored
commit 47a64a13 upstream. Set the ehci->resuming flag for the port we receive a remote wakeup on so that resume signalling can be completed. Without this, the root hub timer will not fire again to check if the resume was completed and there will be a never-ending wait on on the port. This effect is only observed if the HUB IRQ IN does not come after we have initiated the port resume. Signed-off-by:
Roger Quadros <rogerq@ti.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Sarah Sharp authored
commit 203a8661 upstream. When the host controller fails to respond to an Enable Slot command, and the host fails to respond to the register write to abort the command ring, the xHCI driver will assume the host is dead, and call usb_hc_died(). The USB device's slot_id is still set to zero, and the pointer stored at xhci->devs[0] will always be NULL. The call to xhci_check_args in xhci_free_dev should have caught the NULL virt_dev pointer. However, xhci_free_dev is designed to free the xhci_virt_device structures, even if the host is dead, so that we don't leak kernel memory. xhci_free_dev checks the return value from the generic xhci_check_args function. If the return value is -ENODEV, it carries on trying to free the virtual device. The issue is that xhci_check_args looks at the host controller state before it looks at the xhci_virt_device pointer. It will return -ENIVAL because the host is dead, and xhci_free_dev will ignore the return value, and happily dereference the NULL xhci_virt_device pointer. The fix is to make sure that xhci_check_args checks the xhci_virt_device pointer before it checks the host state. See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for further details. This patch doesn't solve the underlying issue, but will ensure we don't see any more NULL pointer dereferences because of the issue. This patch should be backported to kernels as old as 3.1, that contain the commit 7bd89b40 "xhci: Don't submit commands or URBs to halted hosts." Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by:
Vincent Thiele <vincentthiele@gmail.com> Signed-off-by:
-
Oleksij Rempel authored
commit d66eaf9f upstream. in some cases where device is attched to xhci port and do not responding, for example ath9k_htc with stalled firmware, kernel will crash on ring_doorbell_for_active_rings. This patch check if pointer exist before it is used. This patch should be backported to kernels as old as 2.6.35, that contain the commit e9df17eb "USB: xhci: Correct assumptions about number of rings per endpoint" Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Signed-off-by:
-
George Cherian authored
commit 07f3cb7c upstream. Xhci controllers with hci_version > 0.96 gives spurious success events on short packet completion. During webcam capture the "ERROR Transfer event TRB DMA ptr not part of current TD" was observed. The same application works fine with synopsis controllers hci_version 0.96. The same issue is seen with Intel Pantherpoint xhci controller. So enabling this quirk in xhci_gen_setup if controller verion is greater than 0.96. For xhci-pci move the quirk to much generic place xhci_gen_setup. Note from Sarah: The xHCI 1.0 spec changed how hardware handles short packets. The HW will notify SW of the TRB where the short packet occurred, and it will also give a successful status for the last TRB in a TD (the one with the IOC flag set). On the second successful status, that warning will be triggered in the driver. Software is now supposed to not assume the TD is not completed until it gets that last successful status. That means we have a slight race condition, although it should have little practical impact. This patch papers over that issue. It's on my long-term to-do list to fix this race condition, but it is a much more involved patch that will probably be too big for stable. This patch is needed for stable to avoid serious log spam. This patch should be backported to kernels as old as 3.0, that contain the commit ad808333 "Intel xhci: Ignore spurious successful event." The patch will have to be modified for kernels older than 3.2, since that kernel added the xhci_gen_setup function for xhci platform devices. The correct conflict resolution for kernels older than 3.2 is to set XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts. Signed-off-by:
George Cherian <george.cherian@ti.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 09d8091c upstream. Commit a8227415 "tracing: Protect ftrace_trace_arrays list in trace_events.c" added taking the trace_types_lock mutex in trace_events.c as there were several locations that needed it for protection. Unfortunately, it also encapsulated a call to tracing_reset_all_online_cpus() which also takes the trace_types_lock, causing a deadlock. This happens when a module has tracepoints and has been traced. When the module is removed, the trace events module notifier will grab the trace_types_lock, do a bunch of clean ups, and also clears the buffer by calling tracing_reset_all_online_cpus. This doesn't happen often which explains why it wasn't caught right away. Commit a8227415 was marked for stable, which means this must be sent to stable too. Link: http://lkml.kernel.org/r/51EEC646.7070306@broadcom.comReported-by:
Arend van Spril <arend@broadcom.com> Tested-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Oleg Nesterov authored
commit e70e78e3 upstream. tracing_buffers_open() does trace_array_get() and then it wrongly inrcements tr->ref again under trace_types_lock. This means that every caller leaks trace_array: # cd /sys/kernel/debug/tracing/ # mkdir instances/X # true < instances/X/per_cpu/cpu0/trace_pipe_raw # rmdir instances/X rmdir: failed to remove `instances/X': Device or resource busy Link: http://lkml.kernel.org/r/20130719153644.GA18899@redhat.comSigned-off-by:
Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by:
-
Alexander Z Lam authored
commit f77d09a3 upstream. Some error paths did not handle ref counting properly, and some trace files need ref counting. Link: http://lkml.kernel.org/r/1374171524-11948-1-git-send-email-azl@google.comSigned-off-by:
Alexander Z Lam <azl@google.com> Cc: Vaibhav Nagarnaik <vnagarnaik@google.com> Cc: David Sharp <dhsharp@google.com> Cc: Alexander Z Lam <lambchop468@gmail.com> Signed-off-by:
-
Alexander Z Lam authored
commit 609e85a7 upstream. Remove debugfs directories for tracing instances during creation if an error occurs causing the trace_array for that instance to not be added to ftrace_trace_arrays. If the directory continues to exist after the error, it cannot be removed because the respective trace_array is not in ftrace_trace_arrays. Link: http://lkml.kernel.org/r/1373502874-1706-2-git-send-email-azl@google.comSigned-off-by:
-
Saurav Kashyap authored
commit c3ccb1d7 upstream. This fixes a regression where Xyratex controllers and disks were lost by the driver: https://bugzilla.kernel.org/show_bug.cgi?id=59601Reported-by:
Jack Hill <jackhill@jackhill.us> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Ewan D. Milne authored
commit 085b513f upstream. sd_prep_fn will allocate a larger CDB for the command via mempool_alloc for devices using DIF type 2 protection. This CDB was being freed in sd_done, which results in a kernel crash if the command is retried due to a UNIT ATTENTION. This change moves the code to free the larger CDB into sd_unprep_fn instead, which is invoked after the request is complete. It is no longer necessary to call scsi_print_command separately for this case as the ->cmnd will no longer be NULL in the normal code path. Also removed conditional test for DIF type 2 when freeing the larger CDB because the protection_type could have been changed via sysfs while the command was executing. Signed-off-by:
Ewan D. Milne <emilne@redhat.com> Acked-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Jeff Skirvin authored
commit 96f15f29 upstream. This commit fixes a race condition in the isci driver abort task and SSP device task management path. The race is caused when an I/O termination in the SCU hardware is necessary because of an SSP target timeout condition, and the check of the I/O end state races against the HW-termination-driven end state. The failure of the race meant that no TMF was sent to the device to clean-up the pending I/O. Signed-off-by:
Jeff Skirvin <jeffrey.d.skirvin@intel.com> Reviewed-by:
Lukasz Dorau <lukasz.dorau@intel.com> Signed-off-by:
-
Gregory CLEMENT authored
commit faefd550 upstream. When CONFIG_ARM_APPENDED_DTB is selected, if the bootloader provides an ATAG_MEM it replaces the memory size and the memory address in the memory node of the device tree. In the case of a system which can handle more than 4GB, the memory node cell size is 4: each data (memory size and memory address) are 64 bits and then use 2 cells. The current code in atags_to_fdt.c made the assumption of a cell size of 2 (one cell for the memory size and one cell for the memory address), this leads to an improper write of the data and ends with a boot hang. This patch writes the memory size and the memory address on the memory node in the device tree depending of the size of the memory node (32 bits or 64 bits). It has been tested in the 2 cases: - with a dtb using skeleton.dtsi - and with a dtb using skeleton64.dtsi Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by:
Nicolas Pitre <nico@linaro.org> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Nicolin Chen authored
commit 2e7ee15c upstream. Also fix return values for headphone switch updates. Signed-off-by:
Nicolin Chen <b42378@freescale.com> Signed-off-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Richard Zhao authored
commit 647ab784 upstream. The errors were caused by copy/paste mistake in below commit since v3.10: 3489d506 ASoC: tegra: Use common DAI DMA data struct It also corrects slave_id initialization in tegra20_ac97 driver. Signed-off-by:
Richard Zhao <rizhao@nvidia.com> Acked-by:
Stephen Warren <swarren@nvidia.com> Acked-by:
Lucas Stach <dev@lynxeye.de> Signed-off-by:
-
Chih-Chung Chang authored
commit cb6f66a2 upstream. The registers of max98088 are 8 bits, not 16 bits. This bug causes the contents of registers to be overwritten with bad values when the codec is suspended and then resumed. Signed-off-by:
Chih-Chung Chang <chihchung@chromium.org> Signed-off-by:
Dylan Reid <dgreid@chromium.org> Signed-off-by:
-
Fabio Estevam authored
commit 016fcab8 upstream. According to the sgtl5000 reference manual, the default value of CHIP_SSS_CTRL is 0x10. Reported-by:
Oskar Schirmer <oskar@scara.com> Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Clemens Ladisch authored
commit 0699a73a upstream. Commit 18d62711 (firewire: prevent dropping of completed iso packet header data) was intended to be an obvious bug fix, but libdc1394 and FlyCap2 depend on the old behaviour by ignoring all returned information and thus not noticing that not all packets have been received yet. The result was that the video frame buffers would be saved before they contained the correct data. Reintroduce the old behaviour for old clients. Tested-by:
Stepan Salenikovich <stepan.salenikovich@gmail.com> Tested-by:
Josep Bosch <jep250@gmail.com> Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by:
-
David Henningsson authored
commit cd6fb679 upstream. Add two more machines that need quirks for headset mics to work. Tested-by:
Shawn Wang <shawn.wang@canonical.com> BugLink: https://bugs.launchpad.net/bugs/1195636Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
David Henningsson authored
commit 6c29d68a upstream. This quirk is needed for the headset mic to work on this Dell machine. BugLink: https://bugs.launchpad.net/bugs/1195597Signed-off-by:
-
Ren Bigcren authored
commit e7a6121f upstream. The device report an error capacity when read_capacity_16(). Using read_capacity_10() can get the correct capacity. Signed-off-by:
Ren Bigcren <bigcren.ren@sonymobile.com> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by:
Oskar Andero <oskar.andero@sonymobile.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 186a9647 upstream. This patch adds target_get_sess_cmd reference counting for iscsit_handle_task_mgt_cmd(), and adds a target_put_sess_cmd() for the failure case. It also fixes a bug where ISCSI_OP_SCSI_TMFUNC type commands where leaking iscsi_cmd->i_conn_node and eventually triggering an OOPs during struct isert_conn shutdown. Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit b2cb9649 upstream. This patch addresses a bug where RDMA_CM_EVENT_DISCONNECTED may occur before the connection shutdown has been completed by rx/tx threads, that causes isert_free_conn() to wait indefinately on ->conn_wait. This patch allows isert_disconnect_work code to invoke rdma_disconnect when isert_disconnect_work() process context is started by client session reset before isert_free_conn() code has been reached. It also adds isert_conn->conn_mutex protection for ->state within isert_disconnect_work(), isert_cq_comp_err() and isert_free_conn() code, along with isert_check_state() for wait_event usage. (v2: Add explicit iscsit_cause_connection_reinstatement call during isert_disconnect_work() to force conn reset) Cc: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Joern Engel authored
commit 0fbfc46f upstream. This patch fixes a potential buffer overflow while processing iscsi_node_auth input for configfs attributes within NodeACL tfc_tpg_nacl_auth_cit context. Signed-off-by:
Joern Engel <joern@logfs.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 3df8f68a upstream. This patch adds the missing isert_put_reject() logic to post a outgoing payload buffer to hold the 48 bytes of original PDU header request payload for the rejected cmd. It also fixes ISTATE_SEND_REJECT handling in isert_response_completion() -> isert_do_control_comp() code, and drops incorrect iscsi_cmd_t->reject_comp usage. Signed-off-by:
-
Vineet Gupta authored
commit e6c495a9 upstream. zap_pte_range loops from @addr to @end. In the middle, if it runs out of batching slots, TLB entries needs to be flushed for @start to @interim, NOT @interim to @end. Since ARC port doesn't use page free batching I can't test it myself but this seems like the right thing to do. Observed this when working on a fix for the issue at thread: http://www.spinics.net/lists/linux-arch/msg21736.htmlSigned-off-by:
Vineet Gupta <vgupta@synopsys.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: Rik van Riel <riel@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Acked-by:
Catalin Marinas <catalin.marinas@arm.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
- 28 Jul, 2013 11 commits
-
-
Greg Kroah-Hartman authored
-
Takashi Iwai authored
commit 1ea9a69d upstream. The EAPD GPIO is dynamically turned on/off for some machines with Sigmatel codecs, but this didn't work as expected, and it resulted in spontaneous lost of speaker outputs per HP plugging or power-saving. This patch fixes the bug by simply including spec->eapd_mask into spec->gpio_mask and spec->gpio_data bits. Reported-and-tested-by:
Eric Shattow <lucent@gmail.com> Signed-off-by:
-
Eldad Zack authored
commit be2f93a4 upstream. Return SNDRV_PCM_POS_XRUN (snd_pcm_uframes_t) instead of SNDRV_PCM_STATE_XRUN (snd_pcm_state_t) from the pointer function of 6fire, as expected by snd_pcm_update_hw_ptr0(). Caught by sparse. Signed-off-by:
Eldad Zack <eldad@fogrefinery.com> Signed-off-by:
-
Takashi Iwai authored
commit f3e351ee upstream. The quirk for Dell laptops with STAC9228 overrides the pin default config of NID 0x0f to the value with AC_DEFCFG_MISC_NO_PRESENCE bit on. I'm not quite sure why this was done so, but can guess that this was introduced for avoiding this to be muted by another headphone plug. Now, after transition to the generic parser, this workaround rather causes a problem (notably as unexpected speaker mutes) because the pin is seen as if it's always plugged in. Since the generic parser can handle multiple headphone plugging gracefully, we can get rid of this override now. Reported-and-tested-by:
-
Thomas Gleixner authored
commit 5ec2481b upstream. smp_call_function_* must not be called from softirq context. But clock_was_set() which calls on_each_cpu() is called from softirq context to implement a delayed clock_was_set() for the timer interrupt handler. Though that almost never gets invoked. A recent change in the resume code uses the softirq based delayed clock_was_set to support Xens resume mechanism. linux-next contains a new warning which warns if smp_call_function_* is called from softirq context which gets triggered by that Xen change. Fix this by moving the delayed clock_was_set() call to a work context. Reported-and-tested-by:
Artem Savkov <artem.savkov@gmail.com> Reported-by:
Sasha Levin <sasha.levin@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: H. Peter Anvin <hpa@zytor.com>, Cc: Konrad Wilk <konrad.wilk@oracle.com> Cc: John Stultz <john.stultz@linaro.org> Cc: xen-devel@lists.xen.org Cc: stable@vger.kernel.org Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
David Jeffery authored
commit 1c327d96 upstream. In nlmsvc_retry_blocked, the check that the list is non-empty and acquiring the pointer of the first entry is unprotected by any lock. This allows a rare race condition when there is only one entry on the list. A function such as nlmsvc_grant_callback() can be called, which will temporarily remove the entry from the list. Between the list_empty() and list_entry(),the list may become empty, causing an invalid pointer to be used as an nlm_block, leading to a possible crash. This patch adds the nlm_block_lock around these calls to prevent concurrent use of the nlm_blocked list. This was a regression introduced by f904be9c "lockd: Mostly remove BKL from the server". Signed-off-by:
David Jeffery <djeffery@redhat.com> Cc: Bryan Schumaker <bjschuma@netapp.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Soeren Moch authored
commit 414abbd2 upstream. In dvb_ringbuffer lock-less synchronizationof reader and writer threads is done with separateread and write pointers. Sincedvb_ringbuffer_flush() modifies the read pointer, this function must not be called from the writer thread. This patch removes the dvb_ringbuffer_flush() calls in the dmxdev ringbuffer write functions, this fixes Oopses "Unable to handle kernel paging request" I could observe for the call chaindvb_demux_read ->dvb_dmxdev_buffer_read -> dvb_ringbuffer_read_user -> __copy_to_user (the reader side of the ringbuffer). The flush calls at the write side are not necessary anyway since ringbuffer_flush is also called in dvb_dmxdev_buffer_read() when an error condition is set in the ringbuffer. This patch should also be applied to stable kernels. Signed-off-by:
Soeren Moch <smoch@web.de> Reviewed-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by:
-
Takashi Iwai authored
commit e6355ad7 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
Liu ShuoX authored
commit e5248a11 upstream. Prevent automatic system suspend from happening during system shutdown by making try_to_suspend() check system_state and return immediately if it is not SYSTEM_RUNNING. This prevents the following breakage from happening (scenario from Zhang Yanmin): Kernel starts shutdown and calls all device driver's shutdown callback. When a driver's shutdown is called, the last wakelock is released and suspend-to-ram starts. However, as some driver's shut down callbacks already shut down devices and disabled runtime pm, the suspend-to-ram calls driver's suspend callback without noticing that device is already off and causes crash. [rjw: Changelog] Signed-off-by:
Liu ShuoX <shuox.liu@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Theodore Ts'o authored
commit 8acd5e9b upstream. Previously ext4_ext_truncate() was ignoring potential error returns from ext4_es_remove_extent() and ext4_ext_remove_space(). This can lead to the on-diks extent tree and the extent status tree cache getting out of sync, which is particuarlly bad, and can lead to file system corruption and potential data loss. Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Signed-off-by:
-
Barry Grussling authored
commit b579fa52 upstream. This patch adds support for the Schweitzer Engineering Laboratories C662 USB cable based off the CP210x driver. Signed-off-by:
Barry Grussling <barry@grussling.com> Signed-off-by:
-
