This adds a helper function to convert a block req op to a nbd cmd type.
It will be used in the last patch to log the type in the timeout
handler.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Add a helper to set the cmd timeout. It does not really do a lot now,
but will be more useful in the next patches.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The original commit adding the sed-opal library by mistake added two
definitions of OPAL_METHOD_LENGTH, remove one of them.
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

In the function 'response_parse', num_entries will never be 0 as
slen is checked for 0. Hence, the condition 'if (num_entries == 0)'
can never be true.
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The dispatch list is not used any more, as the legacy block IO stack
has been removed.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

As inode wb switching may make sync(2) miss some inodes, they're
synchronized using wb_switch_rwsem so that no wb switching happens
while sync(2) is in progress.  In addition to synchronizing the actual
switching, the rwsem is also used to prevent queueing new switch
attempts while sync(2) is in progress.  This is to avoid queueing too
many instances while the rwsem is held by sync(2).  Unfortunately,
this is too agressive and can block wb switching for a long time if
sync(2) is frequent.

The goal is avoiding expolding the number of scheduled switches, not
avoiding scheduling anything.  Let's use wb_switch_rwsem only for
synchronizing the actual switching and sync(2) and use
isw_nr_in_flight instead for limiting the maximum number of scheduled
switches.  The limit is set to 1024 which should be more than enough
while still avoiding extreme situations.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

WB_FRN_TIME_CUT_DIV is used to tell the foreign inode detection logic
to ignore short writeback rounds to prevent getting confused by a
burst of short writebacks.  The parameter is currently 2 meaning that
anything smaller than half of the running average writback duration
will be ignored.

This is unnecessarily aggressive.  The detection logic uses 16 history
slots and is already reasonably protected against some short bursts
confusing it and the current parameter can lead to tens of seconds of
missed detection depending on the writeback pattern.

Let's change the parameter to 8, so that it only ignores writeback
with are smaller than 12.5% of the current running average.

v2: Add comment explaining what's going on with the foreign detection
    parameters.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

psi tracks the time tasks wait for refaulting pages to become
uptodate, but it does not track the time spent submitting the IO. The
submission part can be significant if backing storage is contended or
when cgroup throttling (io.latency) is in effect - a lot of time is
spent in submit_bio(). In that case, we underreport memory pressure.

Annotate submit_bio() to account submission time as memory stall when
the bio is reading userspace workingset pages.
Tested-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

If blk_mq_init_allocated_queue->elevator_init_mq fails, need to release
the previously requested resources.

Fixes: d3484991 ("blk-mq-sched: allow setting of default IO scheduler")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

As sparse points out, these two copy_from_user() should actually be
copy_to_user().

Fixes: 229b53c9 ("take floppy compat ioctls to sodding floppy.c")
Cc: stable@vger.kernel.org
Acked-by: Alexander Popov <alex.popov@linux.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

A previous commit correctly removed set-but-not-read variables, but
this left two new variables now unused. Kill them.

Fixes: ba6f7da9 ("lightnvm: remove set but not used variables 'data_len' and 'rq_len'")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Enabling Direct I/O with loop devices helps reducing memory usage by
avoiding double caching.  32 bit applications running on 64 bits systems
are currently not able to request direct I/O because is missing from the
lo_compat_ioctl.

This patch fixes the compatibility issue mentioned above by exporting
LOOP_SET_DIRECT_IO as additional lo_compat_ioctl() entry.
The input argument for this ioctl is a single long converted to a 1-bit
boolean, so compatibility is preserved.

Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Alessio Balsini <balsini@android.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

In function sg_split, the second sg_calculate_split will return -EINVAL
when in_mapped_nents is 0.

Indeed there is no need to do second sg_calculate_split and sg_split_mapped
when in_mapped_nents is 0, as in_mapped_nents indicates no mapped entry in
original sgl.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

drivers/lightnvm/pblk-read.c: In function pblk_submit_read_gc:
drivers/lightnvm/pblk-read.c:423:6: warning: variable data_len set but not used [-Wunused-but-set-variable]
drivers/lightnvm/pblk-recovery.c: In function pblk_recov_scan_oob:
drivers/lightnvm/pblk-recovery.c:368:15: warning: variable rq_len set but not used [-Wunused-but-set-variable]

They are not used since commit 48e5da72 ("lightnvm:
move metadata mapping to lower level driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull MD changes from Song.

* 'md-next' of https://github.com/liu-song-6/linux:
  raid1: factor out a common routine to handle the completion of sync write
  md: don't call spare_active in md_reap_sync_thread if all member devices can't work
  md: don't set In_sync if array is frozen
  md: allow last device to be forcibly removed from RAID1/RAID10.
  md: Convert to use int_pow()
  md/raid10: end bio when the device faulty
  md/raid1: end bio when the device faulty
  md/raid6: Set R5_ReadError when there is read failure on parity disk
  raid1: use an int as the return value of raise_barrier()

It's just code clean-up.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

When add one disk to array, the md_reap_sync_thread is responsible
to activate the spare and set In_sync flag for the new member in
spare_active().

But if raid1 has one member disk A, and disk B is added to the array.
Then we offline A before all the datas are synchronized from A to B,
obviously B doesn't have the latest data as A, but B is still marked
with In_sync flag.

So let's not call spare_active under the condition, otherwise B is
still showed with 'U' state which is not correct.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

When a disk is added to array, the following path is called in mdadm.

Manage_subdevs -> sysfs_freeze_array
               -> Manage_add
               -> sysfs_set_str(&info, NULL, "sync_action","idle")

Then from kernel side, Manage_add invokes the path (add_new_disk ->
validate_super = super_1_validate) to set In_sync flag.

Since In_sync means "device is in_sync with rest of array", and the new
added disk need to resync thread to help the synchronization of data.
And md_reap_sync_thread would call spare_active to set In_sync for the
new added disk finally. So don't set In_sync if array is in frozen.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

When the 'last' device in a RAID1 or RAID10 reports an error,
we do not mark it as failed.  This would serve little purpose
as there is no risk of losing data beyond that which is obviously
lost (as there is with RAID5), and there could be other sectors
on the device which are readable, and only readable from this device.
This in general this maximises access to data.

However the current implementation also stops an admin from removing
the last device by direct action.  This is rarely useful, but in many
case is not harmful and can make automation easier by removing special
cases.

Also, if an attempt to write metadata fails the device must be marked
as faulty, else an infinite loop will result, attempting to update
the metadata on all non-faulty devices.

So add 'fail_last_dev' member to 'struct mddev', then we can bypasses
the 'last disk' checks for RAID1 and RAID10, and control the behavior
per array by change sysfs node.
Signed-off-by: NeilBrown <neilb@suse.de>
[add sysfs node for fail_last_dev by Guoqing]
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

Instead of linear approach to calculate power of 10, use generic int_pow()
which does it better.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

Just like raid1, we do not queue write error bio to retry write
and acknowlege badblocks, when the device is faulty.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

When write bio return error, it would be added to conf->retry_list
and wait for raid1d thread to retry write and acknowledge badblocks.

In narrow_write_error(), the error bio will be split in the unit of
badblock shift (such as one sector) and raid1d thread issues them
one by one. Until all of the splited bio has finished, raid1d thread
can go on processing other things, which is time consuming.

But, there is a scene for error handling that is not necessary.
When the device has been set faulty, flush_bio_list() may end
bios in pending_bio_list with error status. Since these bios
has not been issued to the device actually, error handlding to
retry write and acknowledge badblocks make no sense.

Even without that scene, when the device is faulty, badblocks info
can not be written out to the device. Thus, we also no need to
handle the error IO.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

7471fb77 ("md/raid6: Fix anomily when recovering a single device in
RAID6.") avoids rereading P when it can be computed from other members.
However, this misses the chance to re-write the right data to P. This
patch sets R5_ReadError if the re-read fails.

Also, when re-read is skipped, we also missed the chance to reset
rdev->read_errors to 0. It can fail the disk when there are many read
errors on P member disk (other disks don't have read error)

V2: upper layer read request don't read parity/Q data. So there is no
need to consider such situation.

This is Reported-by: kbuild test robot <lkp@intel.com>

Fixes: 7471fb77 ("md/raid6: Fix anomily when recovering a single device in RAID6.")
Cc: <stable@vger.kernel.org> #4.4+
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

Using a sector_t as the return value is misleading, because
raise_barrier() only return 0 or -EINTR.

Also add comments for the return values of raise_barrier().
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

Now that there no module users left of bio_map_kern, stop exporting the
symbol.
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hans Holmberg <hans@owltronix.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

There is no reason now not to use kvmalloc, so replace the internal
metadata allocation scheme.
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hans Holmberg <hans@owltronix.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Now that blk_rq_map_kern can map both kmem and vmem, move internal
metadata mapping down to the lower level driver.
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hans Holmberg <hans@owltronix.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Move the redundant sync handling interface and wait for a completion in
the lightnvm core instead.
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hans Holmberg <hans@owltronix.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Spread queues among present CPUs first, then building mapping on other
non-present CPUs.

So we can minimize count of dead queues which are mapped by un-present
CPUs only. Then bad IO performance can be avoided by unbalanced mapping
between present CPUs and queues.

The similar policy has been applied on Managed IRQ affinity.

Cc: Yi Zhang <yi.zhang@redhat.com>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Implement .cleanup_rq() callback for freeing driver private part
of the request. Then we can avoid to leak this part if the request isn't
completed by SCSI, and freed by blk-mq or upper layer(such as dm-rq) finally.

Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: <stable@vger.kernel.org>
Fixes: 396eaf21 ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

SCSI maintains its own driver private data hooked off of each SCSI
request, and the pridate data won't be freed after scsi_queue_rq()
returns BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE. An upper layer driver
(e.g. dm-rq) may need to retry these SCSI requests, before SCSI has
fully dispatched them, due to a lower level SCSI driver's resource
limitation identified in scsi_queue_rq(). Currently SCSI's per-request
private data is leaked when the upper layer driver (dm-rq) frees and
then retries these requests in response to BLK_STS_RESOURCE or
BLK_STS_DEV_RESOURCE returns from scsi_queue_rq().

This usecase is so specialized that it doesn't warrant training an
existing blk-mq interface (e.g. blk_mq_free_request) to allow SCSI to
account for freeing its driver private data -- doing so would add an
extra branch for handling a special case that all other consumers of
SCSI (and blk-mq) won't ever need to worry about.

So the most pragmatic way forward is to delegate freeing SCSI driver
private data to the upper layer driver (dm-rq).  Do so by adding
new .cleanup_rq callback and calling a new blk_mq_cleanup_rq() method
from dm-rq.  A following commit will implement the .cleanup_rq() hook
in scsi_mq_ops.

Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: <stable@vger.kernel.org>
Fixes: 396eaf21 ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This patch implements newly introduced zone reset all operation for
null_blk driver.
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This patch implements the zone reset all operation for sd_zbc.c. We add
a new boolean parameter for the sd_zbc_setup_reset_cmd() to indicate
REQ_OP_ZONE_RESET_ALL command setup. Along with that we add support in
the completion path for the zone reset all.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This implements REQ_OP_ZONE_RESET_ALL as a special case of the block
device zone reset operations where we just simply issue bio with the
newly introduced req op.

We issue this req op when the number of sectors is equal to the device's
partition's number of sectors and device has no partitions.

We also add support so that blk_op_str() can print the new reset-all
zone operation.

This patch also adds a generic make request check for newly
introduced REQ_OP_ZONE_RESET_ALL req_opf. We simply return error
when queue is zoned and reset-all flag is not set for
REQ_OP_ZONE_RESET_ALL.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

This patch introduces a new request operation REQ_OP_ZONE_RESET_ALL.
This is useful for the applications like mkfs where it needs to reset
all the zones present on the underlying block device. As part for this
patch we also introduce new QUEUE_FLAG_ZONE_RESETALL which indicates the
queue zone reset all capability and corresponding helper macro.
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Change a reference to the legacy block layer into a reference to blk-mq.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

See also commit 8f4236d9 ("block: remove QUEUE_FLAG_BYPASS and ->bypass") # v5.0.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Consider the following example:
* The logical block size is 4 KB.
* The physical block size is 8 KB.
* max_sectors equals (16 KB >> 9) sectors.
* A non-aligned 4 KB and an aligned 64 KB bio are merged into a single
  non-aligned 68 KB bio.

The current behavior is to split such a bio into (16 KB + 16 KB + 16 KB
+ 16 KB + 4 KB). The start of none of these five bio's is aligned to a
physical block boundary.

This patch ensures that such a bio is split into four aligned and
one non-aligned bio instead of being split into five non-aligned bios.
This improves performance because most block devices can handle aligned
requests faster than non-aligned requests.

Since the physical block size is larger than or equal to the logical
block size, this patch preserves the guarantee that the returned
value is a multiple of the logical block size.

Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Move the max_sectors check into bvec_split_segs() such that a single
call to that function can do all the necessary checks. This patch
optimizes the fast path further, namely if a bvec fits in a page.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>