The purpose of this housekeeping is to make some room for
VHT flags. The radiotap vendor fields weren't in use.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In association request frames, there may be IEs passed from
userspace (such as interworking IEs) between HT and VHT, so
add code to insert those inbetween them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In probe request frames, the VHT IEs should come before any
vendor IEs, but after interworking and similar, so add code
to order them correctly wrt. the IEs passed from userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The element ID list is currently almost sorted by amendment
or similar topic, but the order is difficult to maintain and
not very transparent. Sort the list by ID instead, and add
a lot of missing IDs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Update the operating mode field is needed when an association
request contains the operating mode notification element and
it's not just changed later on the fly.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
[clarify commit log, comments & fix whitespace]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In case we will get regulatory request with rule
where max_bandwidth_khz is set to 0 handle this
case as a special one.

If max_bandwidth_khz == 0 we should calculate maximum
available bandwidth base on all frequency contiguous rules.
In case we need auto calculation we just have to set:

country PL: DFS-ETSI
        (2402 - 2482 @ 40), (N/A, 20)
        (5170 - 5250 @ AUTO), (N/A, 20)
        (5250 - 5330 @ AUTO), (N/A, 20), DFS
        (5490 - 5710 @ 80), (N/A, 27), DFS

This mean we will calculate maximum bw for rules where
AUTO (N/A) were set, 160MHz (5330 - 5170) in example above.
So we will get:
        (5170 - 5250 @ 160), (N/A, 20)
        (5250 - 5330 @ 160), (N/A, 20), DFS

In other case:
country FR: DFS-ETSI
        (2402 - 2482 @ 40), (N/A, 20)
        (5170 - 5250 @ AUTO), (N/A, 20)
        (5250 - 5330 @ 80), (N/A, 20), DFS
        (5490 - 5710 @ 80), (N/A, 27), DFS

We will get 80MHz (5250 - 5170):
        (5170 - 5250 @ 80), (N/A, 20)
        (5250 - 5330 @ 80), (N/A, 20), DFS

Base on this calculations we will set correct channel
bandwidth flags (eg. IEEE80211_CHAN_NO_80MHZ).

We don't need any changes in CRDA or internal regulatory.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[extend nl80211 description a bit, fix typo]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

It was possible to break interface combinations in
the following way:

 combo 1: iftype = AP, num_ifaces = 2, num_chans = 2,
 combo 2: iftype = AP, num_ifaces = 1, num_chans = 1, radar = HT20

With the above interface combinations it was
possible to:

 step 1. start AP on DFS channel by matching combo 2
 step 2. start AP on non-DFS channel by matching combo 1

This was possible beacuse (step 2) did not consider
if other interfaces require radar detection.

The patch changes how cfg80211 tracks channels -
instead of channel itself now a complete chandef
is stored.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.

The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.

Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This patch moves the rfkill poll_work to the power efficient workqueue.
This work does not have to be bound to the CPU that scheduled it, hence
the selection of CPU that executes it would be left to the scheduler.
Net result is that CPU idle times would be extended, resulting in power
savings.

This behaviour is enabled when CONFIG_WQ_POWER_EFFICIENT is selected.

Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Shaibal Dutta <shaibal.dutta@broadcom.com>
[zoran.markovic@linaro.org: Rebased to latest kernel, added commit message.
Fixed workqueue selection after suspend/resume cycle.]
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For better use of CPU idle time, allow the scheduler to select the CPU
on which the timeout work of regulatory settings would be executed.
This extends CPU idle residency time and saves power.

This functionality is enabled when CONFIG_WQ_POWER_EFFICIENT is selected.

Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Shaibal Dutta <shaibal.dutta@broadcom.com>
[zoran.markovic@linaro.org: Rebased to latest kernel. Added commit message.]
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Action, disassoc and deauth frames are bufferable, and as such don't
have the PM bit in the frame control field reserved which means we
need to react to the bit when receiving in such a frame.

Fix this by introducing a new helper ieee80211_is_bufferable_mmpdu()
and using it for the RX path that currently ignores the PM bit in
any non-data frames for doze->wake transitions, but listens to it in
all frames for wake->doze transitions, both of which are wrong.

Also use the new helper in the TX path to clean up the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Compiling with W=1 found a few variables that are set
but not used (-Wunused-but-set-variable), remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add helper function that will return regdomain.
Follow the driver's regulatory domain, if present,
unless a country IE has been processed or a user
wants to help compliance further.
Signed-off-by: Janusz Dziedzic <janusz.dziedzi@tieto.com>
[remove useless reg variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Set preset_chandef in channel switch notification.
In other case we will have old preset_chandef.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Responding to probe requests for scanning clients will often create
excessive retries, as it happens quite often that the scanning client
already left the channel. Therefore do it like hostapd and send probe
responses for wildcard SSID only once by using the noack flag.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
[fix typo & 'wildcard SSID' in commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.

This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.

To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)

To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.

I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The ieee80211_vif_use_channel() function calls
ieee80211_vif_release_channel(), so there's no need to call it
explicitly in __ieee80211_sta_join_ibss().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The patch adds a missing sdata lock and adds a few
lockdeps for easier maintenance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

radar_required setting wasn't protected by
local->mtx in some places. This should prevent
from scanning/radar detection/roc colliding.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The sdata->vif.csa_active could be left set after,
e.g. channel context constraints check fail in STA
mode leaving the interface in a strange state for
a brief period of time until it is disconnected.
This was harmless but ugly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If CSA for AP interface failed and the interface
was not stopped afterwards another CSA request
would leak sdata->u.ap.next_beacon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of having
ieee80211_bss_info_change_notify() scattered all
over the place just call it once when finalizing
CSA.

As a side effect this patch adds missing error
checking for IBSS CSA beacon update.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
[fix err vs. changed variable usage in ieee80211_csa_finalize()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There are a few cases, e.g. suspend, where an AP interface is
stopped by the kernel rather than by userspace request, most
commonly when suspending. To let userspace know about this,
send the NL80211_CMD_STOP_AP command as an event every time
an AP interface is stopped. This also happens when userspace
did in fact request the AP stop, but that's not a problem.

For full-MAC drivers this may need to be extended to also
cover cases where the device stopped the AP operation for
some reason, this a bit more complicated because then all
cfg80211 state also needs to be reset; such API is not part
of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

A few places weren't checking that the frame passed to the
function actually has enough data even though the function
clearly documents it must have a payload byte. Make this
safer by changing the function to take an skb and checking
the length inside. The old version is preserved for now as
the rtl* drivers use it and don't have a correct skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If there's a policy, then nla_parse() return values must be
checked, otherwise the policy is useless and there's nothing
that ensures the attributes are actually what we expect them
to be.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ATM, {ADD,DEL}BA and BAR frames are sent on the AC matching the TID of
the BA parameters. In the discussion [1] about this patch, Johannes
recalled that it fixed some races with the DELBA and indeed this
behavior was introduced in [2].
While [2] is right for the BARs, the part queueing the {ADD,DEL}BAs on
their BA params TID AC violates the spec and is more a workaround for
some drivers. Helmut expressed some concerns wrt such drivers, in
particular DELBAs in rt2x00.

ATM, DELBAs are sent after a driver has called (hence "purposely")
ieee80211_start_tx_ba_cb_irqsafe and Johannes and Emmanuel gave some
details wrt intentions behind the split of the IEEE80211_AMPDU_TX_STOP_*
given to the driver ampdu_action supposed to call this function, which
could prove handy to people trying to do the right thing in faulty
drivers (if their fw/hw don't get in their way).

[1] http://mid.gmane.org/1390391564-18481-1-git-send-email-karl.beldan@gmail.com
[2] Commit: cf6bb79a ("mac80211: Use appropriate TID for sending BAR, ADDBA and DELBA frames")
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Advertise to mac80211 that we can do channel switch both
for STA and AP/GO.
After each beacon transmission check if CSA is done and
call ieee80211_csa_finish if needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When creating new devices, allow P2P-Device support to be
turned off to be able to test default behaviour with and
without the support.

Also add a module parameter for the default setting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's not a single rate control algorithm actually in
a separate module where the module refcount would be
required. Similarly, there's no specific rate control
module.

Therefore, all the module handling code in rate control
is really just dead code, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The sample table is initialized only once at module start, so
is really __read_mostly. Additionally, the code to init it can
be marked __init since it will never be needed again, it is
likely automatically inlined into the __init function already
by the compiler, so this doesn't really make a difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The netlink policy in hwsim should be const, there's no
reason for it not to be.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instances of struct device_type are never modified, make them const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no reason for netlink attribute policies to be
__read_mostly, they can just be const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The wiphy privid (to identify wiphys) and the cfg80211
ops should both be const, so change them to be.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Change the code to allow making all the rate control ops
const, nothing ever needs to change them. Also change all
drivers to make use of this and mark the ops const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Restrict our published beamformee STS capability according
to the AP value.
Some AP show bad behaviour in interoperability testing
when our capabilities are better.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Initialize the buffer to all zeroes, otherwise the stack
data might be interpreted as the TID, which is likely to
fail completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In case the given ROC duration is 0, update it to a minimal value before
setting the ieee80211_roc_work parameters, so it also would be valid
for cases where scan is in progress or there are other ROCs queued.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since we copy the mesh_id_len into our own data structures,
use it consistently and don't sometimes use cfg80211's copy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The mesh_id is an array so can't ever be NULL, it looks
like mesh_id_len check was intended instead. However,
since the previous patch, cfg80211 does the check, so
just remove it here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>