Current code for offloading IP-in-IP tunneling assumes that there is no
decap without encap. But that's never true for IPv6 overlays, and is not
true for IPv4 ones either, if net.ipv4.conf.*.rp_filter is unset.

To support decap-only tunnels, an IPIP entry is now created as soon as
an offloadable tunneling device is created. When that netdevice is up'd,
a decap route is looked up and possibly offloaded. Thus decap is not
handled implicitly as part of mlxsw_sp_ipip_entry_get() call anymore,
but needs to be done explicitly after the get, if desired.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far, all netdevice notifications that the driver cared about were
related to its own ports, and mlxsw_sp could be retrieved from the
netdevice's private data. For IP-in-IP offloading however, the driver
cares about events on foreign netdevices, and getting at mlxsw_sp or
router data structures from the handler is inconvenient.

Therefore move the netdevice notifier blocks from global scope to struct
mlxsw_sp to allow retrieval from the notifier block pointer itself.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 2f487712 ("tipc: guarantee that group broadcast doesn't
bypass group unicast") there was introduced a last-minute rebasing
error that broke non-group communication.

We fix this here.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
net: core: rcuify rtnl af_ops

None of the rtnl af_ops callbacks sleep, so they can be called while
holding rcu read lock.

Switch handling of af_ops to rcu.

This would allow to later call af_ops functions without holding
the rtnl mutex anymore.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl af_ops currently rely on rtnl mutex: unregister (called from module
exit functions) takes the rtnl mutex and all users that do af_ops lookup
also take the rtnl mutex. IOW, parallel rmmod will block until doit()
callback is done.

As none of the af_ops implementation sleep we can use rcu instead.

doit functions that need the af_ops can now use rcu instead of the
rtnl mutex provided the mutex isn't needed for other reasons.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

next patch will rcu-ify rtnl af_ops, i.e. allow af_ops
lookup and function calls with rcu read lock held instead
of rtnl mutex.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The structure tcp_cdg is local to the source and
does not need to be in global scope, so make it static.

Cleans up sparse warning:
symbol 'tcp_cdg' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The notifier cause a link error when NET_DSA is a loadable
module:

drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_remove':
bcmsysport.c:(.text+0x1582): undefined reference to `unregister_dsa_notifier'
drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_probe':
bcmsysport.c:(.text+0x278d): undefined reference to `register_dsa_notifier'

This adds a dependency that forces the systemport driver to be
a loadable module as well when that happens, but otherwise
allows it to be built normally when DSA is either built-in or
completely disabled.

Fixes: d1565763 ("net: systemport: Establish lower/upper queue mapping")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify baycom driver to use the new parallel port device model.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Notice that for options.c file, I placed the "fall through" comment
on its own line, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes custom flag handling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All the trace events defined in include/trace/events/bpf.h are only
used when CONFIG_BPF_SYSCALL is defined. But this file gets included by
include/linux/bpf_trace.h which is included by the networking code with
CREATE_TRACE_POINTS defined.

If a trace event is created but not used it still has data structures
and functions created for its use, even though nothing is using them.
To not waste space, do not define the BPF trace events in bpf.h unless
CONFIG_BPF_SYSCALL is defined.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to not dirty the cacheline too often, we try to only update
dst->__use and dst->lastusetime at most once per jiffy.
As dst->lastusetime is only used by ipv6 garbage collector, it should
be good enough time resolution.
And __use is only used in ipv6_route_seq_show() to show how many times a
dst has been used. And as __use is not atomic_t right now, it does not
show the precise number of usage times anyway. So we think it should be
OK to only update it at most once per jiffy.

According to my latest syn flood test on a machine with intel Xeon 6th
gen processor and 2 10G mlx nics bonded together, each with 8 rx queues
on 2 NUMA nodes:
With this patch, the packet process rate increases from ~3.49Mpps to
~3.75Mpps with a 7% increase rate.

Note: dst_use() is being renamed to dst_hold_and_use() to better specify
the purpose of the function.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@googl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In fib6_locate(), we need to first make sure fn is not NULL before doing
FIB6_SUBTREE(fn) to avoid crash.

This fixes the following static checker warning:
net/ipv6/ip6_fib.c:1462 fib6_locate()
         warn: variable dereferenced before check 'fn' (see line 1459)

net/ipv6/ip6_fib.c
  1458          if (src_len) {
  1459                  struct fib6_node *subtree = FIB6_SUBTREE(fn);
                                                    ^^^^^^^^^^^^^^^^
We shifted this dereference

  1460
  1461                  WARN_ON(saddr == NULL);
  1462                  if (fn && subtree)
                            ^^
before the check for NULL.

  1463                          fn = fib6_locate_1(subtree, saddr, src_len,
  1464                                             offsetof(struct rt6_info, rt6i_src)

Fixes: 66f5d6ce ("ipv6: replace rwlock with rcu and spinlock in fib6_table")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update to llvm excludes assembly instructions.
llvm git revision is below

commit 65fad7c26569 ("bpf: add inline-asm support")

This change will be part of llvm  release 6.0

__ASM_SYSREG_H define is not required for native compile.
-target switch includes appropriate target specific files
while cross compiling

Tested on x86 and arm64.
Signed-off-by: Abhijit Ayarekar <abhijit.ayarekar@caviumnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko <jiri@mellanox.com>

====================
net: sched: remove some tp->q usage

In order to prepare for block sharing, tcf_proto instances need to be
independent on particular qdisc instances. This patchset takes care of
removal of couple occurrences of tp->q usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The callers have this info, they will pass it down to tcf_fill_node.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use tcf_block_q helper to get q pointer to be used for direct call of
sch_tree_lock/unlock instead of tcf_tree_lock/unlock.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use helper to get q pointer per block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc_u_common is now per-q. With blocks, it has to be converted to be
per-block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using tp->q, use block to get the net pointer.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever the block->q is set, it can be used instead of tp->q as it
contains the same value. When it is not set, which can't happen now but
it might happen with the follow-up shared blocks introduction, the class
is not set in the result. That would lead to a class lookup instead
of direct class pointer use for classful qdiscs. However, it is not
planned to support classful qdisqs sharing filter blocks, so that may
never happen.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These helpers allows to get a q and netdev pointers
for given block easily.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Store net pointer in the block structure. Along the way, introduce
qdisc_net helper which allows to easily obtain net pointer for
qdisc instance.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare for removal of tp->q and store Qdisc pointer in the block
structure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes a slight tweak to mqprio in order to bring the
classid values used back in line with what is used for mq. The general idea
is to reserve values :ffe0 - :ffef to identify hardware traffic classes
normally reported via dev->num_tc. By doing this we can maintain a
consistent behavior with mq for classid where :1 - :ffdf will represent a
physical qdisc mapped onto a Tx queue represented by classid - 1, and the
traffic classes will be mapped onto a known subset of classid values
reserved for our virtual qdiscs.

Note I reserved the range from :fff0 - :ffff since this way we might be
able to reuse these classid values with clsact and ingress which would mean
that for mq, mqprio, ingress, and clsact we should be able to maintain a
similar classid layout.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2017-10-11: IPoIB Multi Pkey support

This series provides the support for IPoIB Multi Pkey.
InfiniBand Pkeys are the equivalent of Ethernet vlans.
Currently IPoIB device driver supports only default Pkey and IPoIB Pkey child
interfaces are not supported with IPoIB offloads mode, this series will add
the support for that by allowing creating mlx5 multiple IPoIB netdevices with
a non-default Pkey.

mlx5 IPoIB Pkey child interface is smaller version of mlx5i IPoIB interfaces and shares
most of its resources with the parent IPoIB interface, namely RX steering and ring
queue resources.

The only mlx5 resources a child Pkey interface will be creating are the TX rings,
since they should be assigned to a specific Pkey.

mlx5i Pkey netdev is implemented via new mlx5e netdev profile implemented in
mlx5/core/ipoib/ipoib_vlan.c.

The series starts with a refactoring of mlx5e PTP and mlx5 clock implementation
to move the code to be part of mlx5 core rather than mlx5e netdevice, in order to
make mlx5 clock and PTP registration part of the core to be shared with mlx5e
master Ethernet netdev/IPoIB parent netdev and mlx5_ib in the near future.

Add the support for attaching multiple underlay QPs for the different Pkeys
in mlx5 core RX steering.

Add Pkey index to rdma_netdev to add the ability to set PKEY index to lower
IPoIB offload netdev.

Use hash-table to map between DQPN (Destination QP number) to child netdev
for the IPoIB parent netdev to forward RX packets to the corresponding
child Pkey netdev, since the RX rings are shared.

The reset of the series adds the ipoib child Pkey: mlx5e netdev profile,
netdev nods implementation and minimal set of ethtool callbacks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2017-10-13

This series contains updates to mqprio and i40e.

Amritha introduces a new hardware offload mode in tc/mqprio where the TCs,
the queue configurations and bandwidth rate limits are offloaded to the
hardware. The existing mqprio framework is extended to configure the queue
counts and layout and also added support for rate limiting. This is
achieved through new netlink attributes for the 'mode' option which takes
values such as 'dcb' (default) and 'channel' and a 'shaper' option for
QoS attributes such as bandwidth rate limits in hw mode 1.  Legacy devices
can fall back to the existing setup supporting hw mode 1 without these
additional options where only the TCs are offloaded and then the 'mode'
and 'shaper' options defaults to DCB support.  The i40e driver enables the
new mqprio hardware offload mechanism factoring the TCs, queue
configuration and bandwidth rates by creating HW channel VSIs.
In this new mode, the priority to traffic class mapping and the user
specified queue ranges are used to configure the traffic class when the
'mode' option is set to 'channel'. This is achieved by creating HW
channels(VSI). A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC (TC0)
which is for the main VSI. TC0 for the main VSI is also reconfigured as
per user provided queue parameters. Finally, bandwidth rate limits are set
on these traffic classes through the shaper attribute by sending these
rates in addition to the number of TCs and the queue configurations.

Colin Ian King makes an array of constant values "constant".

Alan fixes and issue where on some firmware versions, we were failing to
actually fill out the phy_types which caused ethtool to not report any
link types.  Also hardened against a potentially malicious VF by not
letting the VF to reset itself after requesting to change the number of
queues (via ethtool), let the PF reset the VF to institute the requested
changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Lucas Bates says:

====================
tc-testing: Test suite updates

This patch series is a roundup of changes to the tc-testing
suite:

 - Add test cases for police and mirred modules and some coverage
   in already-submitted test categories
 - Break the test case files down into more user-friendly sizes
 - Bug fix to the tdc.py script's handling of the -l argument

v2: fix the lack of final newlines in two new files (thanks David)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug in the tdc script, where executing tdc
with the -l argument would cause the tests to start running
as opposed to listing all the known test cases.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add basic unit tests for police and skbmod actions in tc.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original submission had the test cases stored in one
monolithic file. This can be unwieldy to edit, especially as more
test cases are added. This patch removes the original tests.json
file in favour of individual ones broken down by category.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tests for flushing gact and mirred were missing. This patch
adds test cases to explicitly test the flush of any installed
gact/mirred actions.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
net: Minor macvlan source mode cleanups

So this patch series is just a few minor cleanups for macvlan source mode.
The first patch addresses double receives when a packet is being routed to
the macvlan destination address, and the other addresses the pkt_type being
updated in cases where it most likely should not be.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the pkt_type to PACKET_HOST only if the destination MAC
address matches on the on the source based macvlan. It didn't make sense to
be updating broadcast, multicast, and non-local destined frames with
PACKET_HOST.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch intoduces a slight adjustment for macvlan to address the fact
that in source mode I was seeing two copies of any packet addressed to the
macvlan interface being delivered where there should have been only one.

The issue appears to be that one copy was delivered based on the source MAC
address and then the second copy was being delivered based on the
destination MAC address. To fix it I am just treating a unicast address
match as though it is not a match since source based macvlan isn't supposed
to be matching based on the destination MAC anyway.

Fixes: 79cf79ab ("macvlan: add source mode")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need a real-time notification for tcp retransmission
for monitoring.

Of course we could use ftrace to dynamically instrument this
kernel function too, however we can't retrieve the connection
information at the same time, for example perf-tools [1] reads
/proc/net/tcp for socket details, which is slow when we have
a lots of connections.

Therefore, this patch adds a tracepoint for __tcp_retransmit_skb()
and exposes src/dst IP addresses and ports of the connection.
This also makes it easier to integrate into perf.

Note, I expose both IPv4 and IPv6 addresses at the same time:
for a IPv4 socket, v4 mapped address is used as IPv6 addresses,
for a IPv6 socket, LOOPBACK4_IPV6 is already filled by kernel.
Also, add sk and skb pointers as they are useful for BPF.

1. https://github.com/brendangregg/perf-tools/blob/master/net/tcpretrans

Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Brendan Gregg <bgregg@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Apparently ife_meta_id2name() is only called when
CONFIG_MODULES is defined.

This fixes:

net/sched/act_ife.c:251:20: warning: ‘ife_meta_id2name’ defined but not used [-Wunused-function]
 static const char *ife_meta_id2name(u32 metaid)
                    ^~~~~~~~~~~~~~~~

Fixes: d3f24ba8 ("net sched actions: fix module auto-loading")
Cc: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Haiyang Zhang says:

====================
hv_netvsc: Add init of send table and var renames

Add initialization of send indirection table. Otherwise it may contain
old info of previous device with different number of channels.

Also, did some variable renaming for easier reading.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>