The EH should fall into I_T recovery (and potentially stronger
remedies) if ABORT TASK fails.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Track sas_ha_struct state so that we ignore events that come in while
we're shutting things down.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Convert the phy port locks to use irq spinlocks.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Add the necessary hooks to the aic94xx driver to support the asynchronous SCSI
device scan infrastructure.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Allowing the phy reset controls to be world-triggerable does not seem like
a terribly good idea because SAS devices can be disrupted (and ATA devices
are really disrupted) by a phy reset.  By default only root should be able
to do things like that.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Extend the use of the DDB lock to include all DDB accesses, because
DDB updates now occur from multiple threads.  This fixes the SMP timeout
problems that we were occasionally seeing with a x260, because the
controller got confused when the DDBs got corrupted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Ed Chim of Adaptec informs us that the DDB registers need to be zeroed at
initialization time and that some SCB initializations need to happen even if
we don't use the SCB.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The vmalloc() blob holding the sequencer firmware wasn't being released at
module unload time, which resulted in a memory leak.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Now that task aborts and device port resets are done by the EH, we can
remove all the code that set up workqueues and such and simply call
sas_task_abort and let libsas figure things out.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

sas_task_abort() should simply abort the upper-level SCSI command and wait
until the error handler to send the actual ABORT TASK command.  By
deferring things to the EH we simplify the concurrency coordination and
eliminate some race conditions.  Note that sas_task_abort has a few hooks
to handle libsas internal commands properly too.

Also rename do_sas_task_abort to __sas_task_abort just in case we really
want to abort the task *right now* and we don't have a scsi_cmnd attached
to the command.  This is a hook for libata internal commands to abort.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

When a SAS LLDD needs to request a device port reset, it needs to have all
commands aborted before it can reset the port.  Since commands are put on
the EH's list in the order that they were queued, the LLDD can set a "need
reset" flag in the last task to be aborted so that the EH can reset the
port after all commands are aborted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This flag is no longer necessary because we push tasks to be aborted into
the EH as soon as we possibly can, and let the SCSI EH code take care of
the coordination for which this flag was used.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

In this driver, TMF_QUERY_TASK translates to QUERY_SSP_TASK.  The
sequencer, it seems, is perfectly happy sending us a SSP response, which
this function promptly "converts" into TMF_RESP_FUNC_FAILED.  This leads to
the SAS EH making bad decisions based on bad data, so we should not perform
the conversion in this case.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Magic number cleanup.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The aic94xx module has a parameter that looks like it should set
lldd_max_execute_num in the sas_ha, but it never sets this value.  Either
we should set it or remove the parameter.  This allows us to enable task
collector mode for this driver, though it is still off by default.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

If we use task collector mode, we can end up destroying the task collector
thread before we release the ports, which is bad if a port release causes
a disk I/O (such as cache flushing).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Every so often, a scsi_cmnd will time out, and the libsas timeout handler
will discover that the scsi_cmnd does not have a sas_task attached to it.
This can happen in two cases: (1) the scsi_cmnd actually made it through
libsas to the HBA and is now going through scsi_done, or (2) the
scsi_cmnd has been held up (host lock, slab alloc, etc) and libsas has
not yet attached a sas_task.  In both cases, it is safe to ask SCSI for
more time to process the command via EH_RESET_TIMER; we cannot blindly
return EH_HANDLED because if (2) happens, we could end up calling
scsi_done while another CPU is heading towards sas_queuecommand, which
causes slab corruption when sas_task_done updates the freed scsi_cmnd.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch lets a user arbitrarily enable or disable a phy via sysfs.
Potential applications include shutting down a phy to replace one
lane of wide port, and (more importantly) providing a method for the
libata SATL to control the phy.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

[SCSI] libsas: Don't give scsi_cmnds to the EH if they never made it to the SAS LLDD or have already returned

On a system with many SAS targets, it appears possible that a scsi_cmnd
can time out without ever making it to the SAS LLDD or at the same time
that a completion is occurring.  In both of these cases, telling the
LLDD to abort the sas_task makes no sense because the LLDD won't know
about the sas_task; what we really want to do is to increase the timer.
Note that this involves creating another sas_task bit to indicate
whether or not the task has been sent to the LLDD; I could have
implemented this by slightly redefining SAS_TASK_STATE_PENDING, but
this way seems cleaner.

This second version amends the aic94xx portion to set the
TASK_AT_INITIATOR flag for all sas_tasks that were passed to
lldd_execute_task.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk.  When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF.  In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.

This patch fixes up sas_expander.c separately because jejb has some
cleanup patches of his own that are a prerequisite.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk.  When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF.  In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Removed spin_unlock_irq()/spin_lock_irq() pairs surrounding
starget_for_each_device() calls.
As Matthew W. pointed out, starget_for_each_device() can be called under
a spinlock being held.
The change has been tested and verified on qla2xxx.ko module.
Thanks Matthew W. and Hisashi H. for help.
Signed-off-by: Andrew Vasquez <Andrew.vasquez@qlogic.com>
Signed-off-by: Seokmann Ju <Seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Hi,

Minor typo ...
In my first iteration of patches (that got merged), the
BLIST_ATTACH_PQ3 actually had the value 0x800000, but that
got changed later to avoid conflicts. This piece must have
been overlooked.
You could obviously do something like %x and then add the
bitflags, but that looks overkill for something that does
not tend to change.

Please merge.
(Patch applied against latest 2.6.20rc version that I tested.)

From: Kurt Garloff <kurt@garloff.de>
Subject: [SCSI SCAN] Fix logging message for PQ3 devices

The blacklist flags BLIST_ATTACH_PQ3 has value 0x1000000,
not 0x800000.
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

More megaraid kernel-doc fixes.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sumant Patro <sumantp@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

kernel-doc modifications:
- change "@param var" notation to @var;
- change function/description separator from ':' to '-';
- change var/description separator from '-' to ':';
- fix a few doc. typos;
- don't use kernel-doc /** lead-in when the doc. block is not kernel-doc;
- use Linux common */ ending comment format instead of **/;
- use correct function parameter names;
- place function parameters immediately after the function short description;
- place kernel-doc immediately before its function or macro;
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sumant Patro <sumantp@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

1.      Changes in Initialization to fix kdump failure.
        Send SYNC command on loading.
        This command clears the pending commands in the adapter
        and re-initialize its internal RAID structure.
        Without this change, megaraid driver either panics or fails to
        initialize the adapter during kdump's second kernel boot
        if there are pending commands or interrupts from other devices
        sharing the same IRQ.
2.      Authors email-id domain name changed from lsil.com to lsi.com.
        Also modified the MODULE_AUTHOR to megaraidlinux@lsi.com
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

After discussions in the thread titled:
    [PATCH] scsi_debug: illegal blocking memory allocation
here is a patch containing the discussed fix and some other
fixes and additions. The patch is against lk 2.6.20-rc3 .
The version is bumped to 1.81 .

ChangeLog:
  - Change several GFP_KERNEL allocations to GFP_ATOMIC
    as they can be called from queuecommand() context
  - check above allocation returns and if out of memory
    report DID_REQUEUE in two cases, DID_NO_CONNECT in
    another, and fail slave configure() in another
  - add support for WRITE BUFFER command
  - add aborted_command error injection support
    (opts mask 0x10), similar mechanism to
    recovered_error injection.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch makes the mptctl pass through available if
the mptsas driver is selected. Without this patch
if mptsas is the only fusion driver chosen, then
the mptctl is not presented as an option.

smp_utils uses the mptctl driver to pass SAS SMP
functions through a MPT SAS HBA.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

scsi_retry_command only has a single caller, so there is no point
in having this function.  Additionally the memset of the sense
buffer it does is entirely superflous as scsi_request_fn already
calls scsi_init_cmd_errh to perform this memset before the command
is reissued.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch adds a SCSI driver for the onboard 53c710 chip of some
SNI RM machines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The D700 needs the burst length setting to the previous 53c700 default
of 8 otherwise it will be effectively disabled.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This is a patch, which allows not only disabling bursting but to specify
different burst lenghts. This feature is needed to get the 53c700 driver
working for the onboard SCSI controller of SNI RM machines, which only
work reliably with a 4 word burst length.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Currently we issue a bounce trace when __blk_queue_bounce() is called,
but that merely means that the device has a lower dma mask than the
higher pages in the system. The bio itself may still be lower pages. So
move the bounce trace into __blk_queue_bounce(), when we know there will
actually be page bouncing.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
  HID: Fix DRIVER_DESC macro
  HID: mousepoll parameter makes no sense for generic HID
  HID: tiny patch to remove a kmalloc cast
  HID: fix mappings for DiNovo Edge Keyboard - Logitech USB BT receiver

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  Revert "ACPI: ibm-acpi: make non-generic bay support optional"
  ACPI: update MAINTAINERS
  ACPI: schedule obsolete features for deletion
  ACPI: delete two spurious ACPI messages
  ACPI: rename cstate_entry_s to cstate_entry
  ACPI: ec: enable printk on cmdline use
  ACPI: Altix: ACPI _PRT support

* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  i915: Fix a DRM_ERROR that should be DRM_DEBUG.

Setting .ConfigBase and .Present is now done at the pcmcia core.

The driver cleanup missed a few places where the driver did set .Present
to PRESENT_OPTION and later to the values from the CIS.  Setting to
PRESENT_OPTION now overrides the values from the CIS.  So just remove
those lines.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

unionfs managed to hit this on s390.  Some architectures use __ptr_t in their
FD_ZERO implementation.  We don't have a __ptr_t.  Switch them over to plain
old void*.

Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We write back the wrong register when configuring the Geode processor.
Instead of storing to CCR4, it stores to CCR3.

Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>