usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add initial version of device tree for S32V234-EVB, including nodes for the
4 Cortex-A53 cores, AIPS bus with UART modules, ARM architected timer and
Generic Interrupt Controller (GIC).

Keep SoC level separate from board level to let future boards with this SoC
share common properties, while the dts files will keep board-dependent
properties.
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Signed-off-by: Dan Nica <dan.nica@nxp.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: Phu Luu An <phu.luuan@nxp.com>
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Assign clocks and clock-rates for audio plls, that audio
drivers can utilize them.

Add dai-tdm-slot-num and dai-tdm-slot-width for sound-wm8524,
that sai driver can generate correct bit clock.

Fixes: 13f3b9fd ("arm64: dts: imx8mm-evk: Enable audio codec wm8524")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add I2C node for switch watchdog present on both Zest and RMB3 boards.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add I2C node for accelerometer present on both Zest and RMB3 boards.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It's 3V3_MAIN, not 3V3V_MAIN on schematic. Fix it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Regulator-vsd-3v3 is supplied via GEN_3V3 rail which is an output of
an "always on" load switch supplied by 3V3_MAIN. GEN_3V3 is also used
as vin-supply by a number of peripherals, so adding it also allows us
to follow the schematic more closely.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update the property #clock-cells = <1> to #clock-cells = <0> of the
dpclk, since the Display output pixel clock driver provides single
clock output.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On i.MX8MQ EVK board, VDD_ARM is from a DC-DC converter which
is always ON, the GPIO1_IO13 is ONLY to switch VDD_ARM's voltage
between 0.9V and 1V for CPU DVFS, so VDD_ARM's GPIO regulator
should be always ON to avoid below confusion after kernel boot
up:

imx8mqevk login:
[   31.776619] vdd_arm: disabling
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable scu key for i.MX8QXP MEK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add scu key node for i.MX8QXP, disabled by default as it
depends on board design.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All nodes are better to follow alphabetical sort except iomuxc
which has huge pinctrl data, better to put it at the end of
file.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adjust some nodes to make them follow alphabetical sort except
iomuxc node which is put at the end of file because of its huge
pinctrl data.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

layerscape otg function should be supported HNP SRP and ADP protocol
accroing to rm doc, but dwc3 code not realize it and use id pin to
detect who is host or device(0 is host 1 is device) this patch is to
enable OTG mode on ls1028ardb ls1088ardb and ls1046ardb in dts
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable pca6416 on i.MX8MM EVK board's i2c3 bus.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable i2c3 for i.MX8MM EVK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The iomuxc node is being put at end of file because of its huge
pinctrl data. I2C devices should be placed in alphabetical sort.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In order to maximise performance of the LCD Controller's 64-bit AXI
bus, for any give speed bin of the device, the AXI master interface
clock(ACLK) clock can be up to CPU_frequency/2, which is already
capable of optimal performance. In general, ACLK is always expected
to be equal to CPU_frequency/2. APB slave interface clock(PCLK) and
Main processing clock(PCLK) both are tied to the same clock as ACLK.

This change followed the LS1028A Architecture Specification Manual.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LX2160A esdhc controllers are setup by the driver to be DMA
coherent, but without marking them as such in DT, Linux thinks they
are not.  This can lead to random sporadic DMA errors, even to the
extent of preventing boot, such as:

mmc0: ADMA error
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr:  0x00000000 | Version:  0x00002202
mmc0: sdhci: Blk size:  0x00000008 | Blk cnt:  0x00000001
mmc0: sdhci: Argument:  0x00000000 | Trn mode: 0x00000013
mmc0: sdhci: Present:   0x01f50008 | Host ctl: 0x00000038
mmc0: sdhci: Power:     0x00000003 | Blk gap:  0x00000000
mmc0: sdhci: Wake-up:   0x00000000 | Clock:    0x000040d8
mmc0: sdhci: Timeout:   0x00000003 | Int stat: 0x00000001
mmc0: sdhci: Int enab:  0x037f108f | Sig enab: 0x037f108b
mmc0: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00002202
mmc0: sdhci: Caps:      0x35fa0000 | Caps_1:   0x0000af00
mmc0: sdhci: Cmd:       0x0000333a | Max curr: 0x00000000
mmc0: sdhci: Resp[0]:   0x00000920 | Resp[1]:  0x001d8a33
mmc0: sdhci: Resp[2]:   0x325b5900 | Resp[3]:  0x3f400e00
mmc0: sdhci: Host ctl2: 0x00000000
mmc0: sdhci: ADMA Err:  0x00000009 | ADMA Ptr: 0x000000236d43820c
mmc0: sdhci: ============================================
mmc0: error -5 whilst initialising SD card

These are caused by the device's descriptor fetch hitting speculatively
loaded CPU cache lines that the CPU does not see through the normal,
non-cacheable DMA coherent mapping that it uses for non-coherent
devices.

DT and the device must agree wrt whether the device is DMA coherent or
not.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add ddr pmu node for i.MX8MN EVK board.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Temperature and hysteresis were picked after the CPU.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use "fsl,imx8mm-ocotp" as i.MX8MN ocotp's fallback compatible instead
of "fsl,imx7d-ocotp" to support SoC UID read, as i.MX8MN reuses
i.MX8MM's SoC ID driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Compared to i.MX7D, i.MX8MM has different ocotp layout, so it should
NOT use "fsl,imx7d-ocotp" as ocotp's fallback compatible, remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable i.MX8MN cpu-idle using generic ARM cpu-idle driver, 2 states
are supported, details as below:

root@imx8mnevk:~# cat /sys/devices/system/cpu/cpu0/cpuidle/state0/name
WFI
root@imx8mnevk:~# cat /sys/devices/system/cpu/cpu0/cpuidle/state0/usage
3098
root@imx8mnevk:~# cat /sys/devices/system/cpu/cpu0/cpuidle/state1/name
cpu-pd-wait
root@imx8mnevk:~# cat /sys/devices/system/cpu/cpu0/cpuidle/state1/usage
3078
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8MN system counter node to enable timer-imx-sysctr
broadcast timer driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8MN can reuse i.MX8MQ's src driver, add "fsl,imx8mq-src" as
src's fallback compatible to enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8MN DDR4 EVK board has a GPIO LED to indicate status,
add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull btrfs fixes from David Sterba:
 "A bunch of fixes that accumulated in recent weeks, mostly material for
  stable.

  Summary:

   - fix for regression from 5.3 that prevents to use balance convert
     with single profile

   - qgroup fixes: rescan race, accounting leak with multiple writers,
     potential leak after io failure recovery

   - fix for use after free in relocation (reported by KASAN)

   - other error handling fixups"

* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
  btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
  btrfs: Fix a regression which we can't convert to SINGLE profile
  btrfs: relocation: fix use-after-free on dead relocation roots
  Btrfs: fix race setting up and completing qgroup rescan workers
  Btrfs: fix missing error return if writeback for extent buffer never started
  btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
  Btrfs: fix selftests failure due to uninitialized i_mode in test inodes

Pull csky updates from Guo Ren:
 "This round of csky subsystem just some fixups:

   - Fix mb() synchronization problem

   - Fix dma_alloc_coherent with PAGE_SO attribute

   - Fix cache_op failed when cross memory ZONEs

   - Optimize arch_sync_dma_for_cpu/device with dma_inv_range

   - Fix ioremap function losing

   - Fix arch_get_unmapped_area() implementation

   - Fix defer cache flush for 610

   - Support kernel non-aligned access

   - Fix 610 vipt cache flush mechanism

   - Fix add zero_fp fixup perf backtrace panic

   - Move static keyword to the front of declaration

   - Fix csky_pmu.max_period assignment

   - Use generic free_initrd_mem()

   - entry: Remove unneeded need_resched() loop"

* tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux:
  csky: Move static keyword to the front of declaration
  csky: entry: Remove unneeded need_resched() loop
  csky: Fixup csky_pmu.max_period assignment
  csky: Fixup add zero_fp fixup perf backtrace panic
  csky: Use generic free_initrd_mem()
  csky: Fixup 610 vipt cache flush mechanism
  csky: Support kernel non-aligned access
  csky: Fixup defer cache flush for 610
  csky: Fixup arch_get_unmapped_area() implementation
  csky: Fixup ioremap function losing
  csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range
  csky/dma: Fixup cache_op failed when cross memory ZONEs
  csky: Fixup dma_alloc_coherent with PAGE_SO attribute
  csky: Fixup mb() synchronization problem

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes that have trickled in through the merge window:

   - Video fixes for OMAP due to panel-dpi driver removal

   - Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7

   - Fixing arch version on ASpeed ast2500

   - Two fixes for reset handling on ARM SCMI"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: aspeed: ast2500 is ARMv6K
  reset: reset-scmi: add missing handle initialisation
  firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
  bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
  ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
  ARM: dts: am3517-evm: Fix missing video
  ARM: dts: logicpd-torpedo-baseboard: Fix missing video
  ARM: omap2plus_defconfig: Fix missing video
  bus: ti-sysc: Fix handling of invalid clocks
  bus: ti-sysc: Fix clock handling for no-idle quirks

Pull tracing fixes from Steven Rostedt:
 "A few more tracing fixes:

   - Fix a buffer overflow by checking nr_args correctly in probes

   - Fix a warning that is reported by clang

   - Fix a possible memory leak in error path of filter processing

   - Fix the selftest that checks for failures, but wasn't failing

   - Minor clean up on call site output of a memory trace event"

* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  selftests/ftrace: Fix same probe error test
  mm, tracing: Print symbol name for call_site in trace events
  tracing: Have error path in predicate_parse() free its allocated memory
  tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
  tracing/probe: Fix to check the difference of nr_args before adding probe

Pull more MMC updates from Ulf Hansson:
 "A couple more updates/fixes for MMC:

   - sdhci-pci: Add Genesys Logic GL975x support

   - sdhci-tegra: Recover loss in throughput for DMA

   - sdhci-of-esdhc: Fix DMA bug"

* tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: host: sdhci-pci: Add Genesys Logic GL975x support
  mmc: tegra: Implement ->set_dma_mask()
  mmc: sdhci: Let drivers define their DMA mask
  mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence
  mmc: sdhci: improve ADMA error reporting

Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):

arch/csky/kernel/perf_event.c:1340:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Pull Documentation/process update from Greg KH:
 "Here are two small Documentation/process/embargoed-hardware-issues.rst
  file updates that missed my previous char/misc pull request.

  The first one adds an Intel representative for the process, and the
  second one cleans up the text a bit more when it comes to how the
  disclosure rules work, as it was a bit confusing to some companies"

* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Documentation/process: Clarify disclosure rules
  Documentation/process: Volunteer as the ambassador for Intel

Pull more vfs updates from Al Viro:
 "A couple of misc patches"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  afs dynroot: switch to simple_dir_operations
  fs/handle.c - fix up kerneldoc

Pull more cifs updates from Steve French:
 "Fixes from the recent SMB3 Test events and Storage Developer
  Conference (held the last two weeks).

  Here are nine smb3 patches including an important patch for debugging
  traces with wireshark, with three patches marked for stable.

  Additional fixes from last week to better handle some newly discovered
  reparse points, and a fix the create/mkdir path for setting the mode
  more atomically (in SMB3 Create security descriptor context), and one
  for path name processing are still being tested so are not included
  here"

* tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Fix oplock handling for SMB 2.1+ protocols
  smb3: missing ACL related flags
  smb3: pass mode bits into create calls
  smb3: Add missing reparse tags
  CIFS: fix max ea value size
  fs/cifs/sess.c: Remove set but not used variable 'capabilities'
  fs/cifs/smb2pdu.c: Make SMB2_notify_init static
  smb3: fix leak in "open on server" perf counter
  smb3: allow decryption keys to be dumped by admin for debugging