qh_refresh is always called when the qh is idle and has not been
linked into hardware queue, so EHCI will not access overlay of
the qh at this time. Just before linking qh into hardware queue, there
has already one wmb to order writing qh descriptor and writing dma
address of the qh into hardware queue, so HC can always see
up-to-date qh descriptor once the qh is fetched with its dma address
by EHCI.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

here is the patch to support Owen SI-30 device.
This is a pulse counter controller.
http://www.owen.ru/en/catalog/93788515

usb-drivers output:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=03eb ProdID=0030 Rev=01.01
C:  #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=00 Driver=cdc_acm
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm

This patch is installed on my home system which receives data from this
controller connected to cold water counter.
Signed-off-by: Denis Pershin <dyp@perchine.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

A typo in the configuration variable name prevents from activating the
USB autosuspend on the device.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The allocated chardevice region range is only 1 device but on
unregister it currently tries to deregister 2.

Found this while doing a insmod/rmmod/insmod/rm... of the module
which seemed to eat major numbers.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When a transceiver is available use otg_set_power to submit
the target current to it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In a few places in the kernel, the code prints
a human-readable USB device speed (eg. "high speed").
This involves a switch statement sometimes wrapped
around in ({ ... }) block leading to code repetition.

To mitigate this issue, this commit introduces
usb_speed_string() function, which returns
a human-readable name of provided speed.

It also changes a few places switch was used to use
this new function.  This changes a bit the way the
speed is printed in few instances at the same time
standardising it.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

IDs found in the Windows driver's ZTEusbnet.inf file from the
ZTE MF100 drivers (O2 UK).  Also fixes the ZTE MF626 device
since it really is distinct from the 4G Systems stick and
apparently needs the net interface blacklisted too, while
there's no indication (yet) that the 4G Systems stick does.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

That's what the blacklist is for...
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

It's cleaner than the array stuff, and we're about to add a bunch
more blacklist entries.  Second, there are devices that need both
the sendsetup and the reserved interface blacklists, which the
current code can't accommodate.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

remove the following two paragraphs as they are not needed:

This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public
License for more details.

You should have received a copy of the GNU General Public License along with
this program; if not, write to the Free Software Foundation, Inc.,59
Temple Place - Suite 330, Boston, MA  02111-1307, USA.
Signed-off-by: Klaus Schwarzkopf <schwarzkopf@sensortherm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

There is a multi-year old bug in the MUSB hardware which is not documented.
It causes spurious interrupts and have various symptoms, like endless
"SetupEnd came in a wrong ep0stage" messages. The fix is taken from the
FreeBSD's musb driver.

How to reproduce:
For example issue clear-stall on a couple of endpoints very fast,
like one request per 125us. After a while the bug triggers and the
musb-chip becomes unusable until next re-enumeration.
Signed-off-by: Hans Petter Selasky <hps@bitfrost.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

A return value of -EINPROGRESS from pm_runtime_get indicates that
the device is already resuming due to a previous call.  Internally,
usb_autopm_get_interface_async doesn't treat this as an error and
increments the usage count, but passes the error status along
to the caller.  The logical assumption of the caller is that
any negative return value reflects the device not resuming
and the pm_usage_cnt not being incremented.  Since the usage count
is being incremented and the device is resuming, return success (0)
instead.
Signed-off-by: James Wylder <james.wylder@motorola.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch solves two things:
1) Enables autosense emulation code to correctly
interpret descriptor format sense data, and
2) Fixes a bug whereby the autosense emulation
code would overwrite descriptor format sense data
with SENSE KEY HARDWARE ERROR in fixed format, to
incorrectly look like this:

Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc]  Sense Key : Recovered Error [current] [descriptor]
Oct 21 14:11:07 localhost kernel: Descriptor sense data with sense descriptors (in hex):
Oct 21 14:11:07 localhost kernel:        72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00
Oct 21 14:11:07 localhost kernel:        00 4f 00 c2 00 50
Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc]  ASC=0x4 ASCQ=0x1d
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The xhci_hcd->devs is an array of pointers rather than pointer to pointer.
Hence this check is not required.

Signed-off-by: Sifram Rajas <Sifram Rajas sifram.rajas@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In xhci_urb_enqueue(), allocate a block of memory for all the TDs instead
of allocating memory for each of them separately. This reduces the number
of kzalloc calling when an isochronous usb is submitted.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Now that the xHCI driver always return a status value of zero for isochronous
URBs, when the last TD of an isochronous URB is short, the local variable
"status" stays set to -EINPROGRESS.  When xHCI driver debugging is turned on,
this causes the log file to fill with messages like this:

[   38.859282] xhci_hcd 0000:00:14.0: Giveback URB ffff88013ad47800, len = 1408, expected = 580, status = -115

Don't print out the status of an URB for isochronous URBs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The xHCI host controller in the Intel Panther Point chipset needs to have
software check whether new devices will fit in the available bus
bandwidth.  Activate the software bandwidth checking quirk when we find
the right PCI device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Now that we have a bandwidth interval table per root port or TT that
describes the endpoint bandwidth information, we can finally use it to
check whether the bus bandwidth is oversubscribed for a new device
configuration/alternate interface setting.

The complication for this algorithm is that the bit of hardware logic that
creates the bus schedule is only 12-bit logic.  In order to make sure it
can represent the maximum bus bandwidth in 12 bits, it has to convert the
endpoint max packet size and max esit payload into "blocks" (basically a
less-precise representation).  The block size for each speed of device is
different, aside from low speed and full speed.  In order to make sure we
don't allow a setup where the scheduler might fail, we also have to do the
bandwidth checking in blocks.

After checking that the endpoints fit in the schedule, we store the
bandwidth used for this root port or TT.  If this is a FS/LS device under
an external HS hub, we also update the TT bandwidth and the root port
bandwidth (if this is a newly activated or deactivated TT).

I won't go into the details of the algorithm, as it's pretty well
documented in the comments.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In order to update the root port or TT's bandwidth interval table, we will
need to keep track of a list of endpoints, per interval.  That way we can
easily know the new largest max packet size when we have to remove an
endpoint.

Add an endpoint list for each root port or TT structure, sorted by
endpoint max packet size.  Insert new endpoints into the list such that
the head of the list always has the endpoint with the greatest max packet
size.  Only insert endpoints and update the interval table with new
information when those endpoints are periodic.

Make sure to update the number of active TTs when we add or drop periodic
endpoints.  A TT is only considered active if it has one or more periodic
endpoints attached (control and bulk are best effort, and counted in the
20% reserved on the high speed bus).  If the number of active endpoints
for a TT was zero, and it's now non-zero, increment the number of active
TTs for the rootport.  If the number of active endpoints was non-zero, and
it's now zero, decrement the number of active TTs.

We have to be careful when we're checking the bandwidth for a new
configuration/alt setting.  If we don't have enough bandwidth, we need to
be able to "roll back" the bandwidth information stored in the endpoint
and the root port/TT interval bandwidth table.  We can't just create a
copy of the interval bandwidth table, modify it, and check the bandwidth
with the copy because we have lists of endpoints and entries can't be on
more than one list.  Instead, we copy the old endpoint bandwidth
information, and use it to revert the interval table when the bandwidth
check fails.

We don't check the bandwidth after endpoints are dropped from the interval
table when a device is reset or freed after a disconnect, because having
endpoints use less bandwidth should not push the bandwidth usage over the
limits.  Besides which, we can't fail a device disconnect.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In the upcoming patches, we'll use some stored endpoint information to
make software keep track of the worst-case bandwidth schedule.  We need to
store several variables associated with each periodic endpoint:
 - the type of endpoint
 - Max Packet Size
 - Mult
 - Max ESIT payload
 - Max Burst Size (aka number of packets, stored in one-based form)
 - the endpoint interval (normalized to powers of 2 microframes)

All this information is available to the hardware, and stored in its
device output context.  However, we need to ensure that the new
information is stored before the xHCI driver drops the xhci->lock to wait
on the Configure Endpoint command, so that another driver requesting a
configuration or alt setting change will see the update.  The Configure
Endpoint command will never fail on the hardware that needs this software
bandwidth checking (assuming the slot is enabled and the flags are set
properly), so updating the endpoint info before the command completes
should be fine.

Until we add in the bandwidth checking code, just update the endpoint
information after the Configure Endpoint command completes, and after a
Reset Device command completes.  Don't bother to clear the endpoint
bandwidth info when a device is being freed, since the xhci_virt_ep is
just going to be freed anyway.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

For upcoming patches, we need to keep information about the bandwidth
domains under the xHCI host.  Each root port is a separate primary
bandwidth domain, and each high speed hub's TT (and potentially each port
on a multi-TT hub) is a secondary bandwidth domain.

If the table were in text form, it would look a bit like this:

EP Interval	Sum of Number	Largest Max	Max Packet
		of Packets	Packet Size	Overhead
	0	   N		   mps		  overhead
...
	15	   N		   mps		  overhead

Overhead is the maximum packet overhead (for bit stuffing, CRC, protocol
overhead, etc) for all the endpoints in this interval.  Devices with
different speeds have different max packet overhead.  For example, if
there is a low speed and a full speed endpoint that both have an interval
of 3, we would use the higher overhead (the low speed overhead).  Interval
0 is a bit special, since we really just want to know the sum of the max
ESIT payloads instead of the largest max packet size.  That's stored in
the interval0_esit_payload variable.  For root ports, we also need to keep
track of the number of active TTs.

For each root port, and each TT under a root port, store some information
about the bandwidth consumption.  Dynamically allocate an array of root
port bandwidth information for the number of root ports on the xHCI host.
Each root port stores a list of TTs under the root port.  A single TT hub
only has one entry in the list, but a multi-TT hub will have an entry per
port.

When the USB core says that a USB device is a hub, create one or more
entries in the root port TT list for the hub.  When a device is deleted,
and it is a hub, search through the root port TT list and delete all
TT entries for the hub.  Keep track of which TT entry is associated with a
device under a TT.

LS/FS devices attached directly to the root port will have usb_device->tt
set to the roothub.  Ignore that, and treat it like a primary bandwidth
domain, since there isn't really a high speed bus between the roothub and
the host.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Since the xHCI driver now has split USB2/USB3 roothubs, devices under each
roothub can have duplicate "fake" port numbers.  For the next set of
patches, we need to keep track of the "real" port number that the xHCI
host uses to index into the port status arrays.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Move the code to check whether we've reached the host controller's limit
on the number of endpoints out of the two conditional statements, to
remove duplicate code.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The "port" field in xhci_virt_dev stores the port number associated with
one of the two xHCI split roothubs, not the unique port number the xHCI
hardware uses.  Since we'll need to store the real hardware port number in
future patches, rename this field to "fake_port".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Some alternate interface settings have no endpoints associated with them.
This shows up in some USB webcams, particularly the Logitech HD 1080p,
which uses the uvcvideo driver.  If a driver switches between two alt
settings with no endpoints, there is no need to issue a configure endpoint
command, because there is no endpoint information to update.

The only time a configure endpoint command with just the add slot flag set
makes sense is when the driver is updating hub characteristics in the slot
context.  However, that code never calls xhci_check_bandwidth, so we
should be safe not issuing a command if only the slot context add flag is
set.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This was done to resolve a conflict in this file:
	drivers/usb/host/xhci-ring.c
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix V2 (incremental)
  OMAP: omap_device: only override _noirq methods, not normal suspend/resume
  PM / Runtime: Correct documentation of pm_runtime_irq_safe()
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix
  sh-sci / PM: Use power.irq_safe
  PM: Use spinlock instead of mutex in clock management functions

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: sbp2: fix panic after rmmod with slow targets

This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
 - Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Fix wrong initializer for "locked" variable in assert_panel_unlocked
  i915: do not setup intel_backlight twice

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
  USB: ftdi_sio: add Calao reference board support
  USB option driver K3765/K4505 avoid CDC_DATA interface
  USB: option: add YUGA device id to driver
  usb: s5p-ehci: fix a NULL pointer deference
  USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume().
  USB option driver add PID of Huawei Vodafone K4605
  USB option driver add PID of Huawei Vodafone K3806
  xhci: Handle zero-length isochronous packets.
  USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
  usb: musb: gadget: fix error path
  usb: gadget: f_phonet: unlock in error case
  usb: musb: blackfin: include prefetch head file
  usb: musb: tusb6010: fix compilation
  usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h
  usb: musb: cppi: fix build errors due to DBG and missing musb variable
  usb: musb: ux500: replace missing DBG with dev_dbg
  usb: musb: ux500: set dma config for both src and dst
  usb: musb: fix oops on musb_gadget_pullup
  usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1)
  usb: gadget: hid: don't STALL when processing a HID Descriptor request
  ...

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  omap-serial: Allow IXON and IXOFF to be disabled.
  TTY: serial, document ignoring of uart->ops->startup error
  TTY: pty, fix pty counting
  8250: Fix race condition in serial8250_backup_timeout().
  serial/8250_pci: delete duplicate data definition
  8250_pci: add support for Rosewill RC-305 4x serial port card
  tty: Add "spi:" prefix for spi modalias
  atmel_serial: fix atmel_default_console_device
  serial: 8250_pnp: add Intermec CV60 touchscreen device
  drivers/serial/ucc_uart.c: Fix compiler warning
  pch_uart: Set PCIe bus number using probe parameter
  serial: samsung: Fix build error

Merge branch 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6

* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  drivers:misc: ti-st: fix unexpected UART close
  drivers:misc: ti-st: free skb on firmware download
  drivers:misc: ti-st: wait for completion at fail
  drivers:misc: ti-st: reinit completion before send
  drivers:misc: ti-st: fail-safe on wrong pkt type
  drivers:misc: ti-st: reinit completion on ver read
  drivers:misc:ti-st: platform hooks for chip states
  drivers:misc: ti-st: avoid a misleading dbg msg
  base/devres.c: quiet sparse noise about context imbalance
  pti: add missing CONFIG_PCI dependency
  drivers/base/devtmpfs.c: correct annotation of `setup_done'
  driver core: fix kernel-doc warning in platform.c
  firmware: fix google/gsmi.c build warning

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  staging: tidspbridge: fix compilation on dsp clock functions
  staging: octeon-ethernet: Add missing #includes.
  Staging: zcache: signedness bug in tmem_get()
  staging: zcache: fix crash on high memory swap
  staging: brcm80211: SPARC build error fix
  staging: brcm80211: fix compile error on non-x86 archs since 3.0 kernel

Signed-off-by: Michal Sroczynski <msroczyn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] memory hotplug: only unassign assigned increments
  [S390] Change default action from reipl to stop for on_restart
  [S390] arch/s390/kernel/ipl.c: correct error detection check
  [S390] drivers/s390/block/dasd_ioctl.c: add missing kfree
  [S390] nss,initrd: kernel image and initrd must be in different segments

According to the SFI specification irq number 0xFF means device has no
interrupt or interrupt attached via GPIO.

Currently, we don't handle this special case and set irq field in
*_board_info structs to 255.  It leads to confusion in some drivers.
Accelerometer driver tries to register interrupt 255, fails and prints
"Cannot get IRQ" to dmesg.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>