- 29 Aug, 2011 37 commits
-
-
Emmanuel Grumbach authored
Now that the reclaim flow has been moved to the transport layer, a lot of functions can be made static or don't need to be exported outside the transport layer. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Emmanuel Grumbach authored
The reclaim flow is really transport related. Define a simple API to allow the upper layer to request from the transport layer to reclaim packets until an index written in the Tx response / BA notification. The transport layer prepares a list of the packets that are being freed and passes this list to the upper layer. Between the two layers, the CB of the skb is used to pass a pointer to the context (BSS / PAN) in which the skb was sent. Signed-off-by:
-
Emmanuel Grumbach authored
It is accessed by the transport layer only, hence the move. The debugfs handlers that accessed it moved to the transport layer too. The rx_handlers part of it stayed in the upper layer and a special debugfs has been added for it Also add missing includes to iwl-commands.h. Signed-off-by:
-
Wey-Yi Guy authored
Add more comments to iwl_mod_params Signed-off-by:
-
Wey-Yi Guy authored
Add comments for better description Signed-off-by:
-
Wey-Yi Guy authored
Different subsystem ID Signed-off-by:
-
Wey-Yi Guy authored
Enable HT aggregation when it reach reasonable traffic without checking traffic load which delay enabling the aggregation and lower the throughput but this behavior can be overwrite by module parameter this address https://bugzilla.kernel.org/show_bug.cgi?id=40042Signed-off-by:
-
Emmanuel Grumbach authored
It is transport dependent, move to the PCIe transport layer. Signed-off-by:
-
Emmanuel Grumbach authored
Since the ISR is entirely in the transport layer, its data should be in the pcie specific region. Change sync_irq to first disable and then synchronize the IRQ. iwl_isr and iwl_isr_ict now receive iwl_trans. Signed-off-by:
-
Emmanuel Grumbach authored
These flows needs to access the APM and a few other registers that can differ between different transports. Signed-off-by:
-
Emmanuel Grumbach authored
Since this struct is specific to pcie transport, move it the the pcie specific transport layer. Signed-off-by:
-
Emmanuel Grumbach authored
Add a handler in iwl_trans_ops to allow it to add entries under debugfs dir given by the upper level. Signed-off-by:
-
Emmanuel Grumbach authored
Rename the recursive inclusion protection in iwl-bus.h while we are at it. Signed-off-by:
-
Emmanuel Grumbach authored
Remove iwl_transport_register which was a W/A. The bus layer knows what transport to use. So now, the bus layer gives the upper layer a pointer to the iwl_trans_ops struct that it wants to use. The upper layer then, allocates the desired transport layer using iwl_trans_ops->alloc function. As a result of this, priv->trans, no longer exists, priv holds a pointer to iwl_shared, which holds a pointer to iwl_trans. This required to change all the calls to the transport layer from upper layer. While we were at it, trans_X inlines have been renamed to iwl_trans_X to avoid confusions, which of course required to rename the functions inside the transport layer because of conflicts in names. So the static API functions inside the transport layer implementation have been renamed to iwl_trans_pcie_X. Until now, the IRQ / Tasklet were initialized in iwl_transport_layer. This is confusing since the registration doesn't mean to request IRQ, so I added a handler for that. Signed-off-by:
-
Emmanuel Grumbach authored
Since it is used by all the layers, it needs to move to iwl_shared. Signed-off-by:
-
Emmanuel Grumbach authored
instead of IWL_DEBUG(priv, IWL_DL_FW_ERRORS Signed-off-by:
-
Emmanuel Grumbach authored
Since all the layers need to print debug message, the debug macro cannot suppose that they will be given iwl_priv as a parameter and then dereference it. Use iwl_shared instead. Signed-off-by:
-
Emmanuel Grumbach authored
Since it is used by all the layers, it needs to move to iwl_shared. Signed-off-by:
-
Emmanuel Grumbach authored
Since it is used by all the layers, it needs to move to iwl_shared. Signed-off-by:
-
Emmanuel Grumbach authored
Since it is used by all the layers, it needs to move to iwl_shared. Signed-off-by:
-
Emmanuel Grumbach authored
Since it is used by all the layers, it needs to move to iwl_shared. Signed-off-by:
-
Emmanuel Grumbach authored
Since it is used by all the layers, it needs to move to iwl_shared. Signed-off-by:
-
Emmanuel Grumbach authored
Since it is used by all the layers, it needs to move to iwl_shared. Signed-off-by:
-
Emmanuel Grumbach authored
This will allow all the modules to look at it. Signed-off-by:
-
Emmanuel Grumbach authored
This struct will hold pointers to all the layers, so that every layer will find the pointers it needs when calling another layer. Note that the drv_data set to struct device is now a pointer to struct iwl_shared. This solves of bug that I introduced in iwlagn: simplify the bus architecture Bug description: sysfs gets the the driver data from struct device. Till the aforementioned patch, dev_get_drvdata would return iwl_priv. After the patch, dev_get_drvdata return iwl_bus which is buggy since the sysfs handlers rely on this value, and sysfs handlers need iwl_priv. Now, dev_get_drvdata return iwl-shared. Since we have pointers to all the layers in iwl_shared, every layer will be able to get the pointer it needs: bus layer will gets iwl_bus from the PCI suspend callbacks, and the sysfs handlers will get the iwl_priv they need. In order to keep good encapsulation, we need to avoid to dereference iwl_priv from a different layer. This is why instead of including iwl-dev.h from iwl-shared.h, I added a forward declaration to iwl_priv. Moreover we keep type safety while providing encapsulation. Signed-off-by:
-
Emmanuel Grumbach authored
It will hold declaration of functions and forward declaration of struct that are used by several layers. This will allow modules not to include iwl_priv. iwl_bus and iwl_trans are still visible to all. All the layers share the module parameters, move the struct to iwl-shared.h. Also add all module parameters to iwl_mod_params instead of having them as global static. This includes * debug_level * ant_coupling * bt_ch_announce * wanted_ucode_alternative Signed-off-by:
-
Emmanuel Grumbach authored
The latter may return incomplete information. For example, if one switched IWL_DL_TX on through sysfs, IWL_DL_TX bit would have been set in priv->debug_level, but since iwl_alloc_traffic_mem looked at iwl_debug_level only, it wouldn't have allocated the tx_traffic buffer. Signed-off-by:
-
Wey-Yi Guy authored
Portion of iwl_cfg comments is not correct anymore, remove it. Signed-off-by:
-
Wey-Yi Guy authored
There are number of functions with "iwlcore_" prefix which not feels right, rename those to "iwl_". No functional changes by making the renames. Signed-off-by:
-
Mohammed Shafi Shajakhan authored
removed a function declaration, removed a variable, renamed a variable Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
in the Rx path of the driver it would be better to use ATH_DBG_ANY rather than ATH_DBG_XMIT for printing debug messages Signed-off-by:
-
Christian Lamparter authored
Use the do_div macro for 64-bit division. Otherwise, the module will reference __udivdi3 under 32-bit kernels, which is not allowed in kernel space. Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Florian Fainelli authored
AR9340 is not listed in ath_mac_bb_names, which leads to such a message: ieee80211 phy0: Atheros AR???? Rev:0 mem=0xb8100000, irq=2 Signed-off-by:
Florian Fainelli <florian@openwrt.org> Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
John W. Linville authored
This seems a bit less awkward... Signed-off-by: -
Peter Huewe authored
This patch replaces the code for getting an number from a userspace buffer by a simple call to kstrou8_from_user. This makes it easier to read and less error prone. Since the old buffer was only 10 bytes long and the value is masked by a nibble-mask anyway, we don't need to use kstrtoul but rather kstrtou8. Kernel Version: v3.0-rc2 Signed-off-by:
Peter Huewe <peterhuewe@gmx.de> Signed-off-by:
-
-
- 26 Aug, 2011 3 commits
-
-
Luis R. Rodriguez authored
This has been tested in STA and AP mode by Florian. Cc: David Quan <dquan@qca.qualcomm.com> Cc: Kathy Giori <kgiori@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Tested-by:
Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by:
-
Christian Lamparter authored
Use the do_div macro for 64-bit division. Otherwise, the module will reference __udivdi3 under 32-bit kernels, which is not allowed in kernel space. drivers/built-in.o: In function `carl9170_collect_tally': cmd.c:191: undefined reference to `__udivdi3' cmd.c:192: undefined reference to `__udivdi3' cmd.c:193: undefined reference to `__udivdi3' Reported-by:
Kalle Valo <kvalo@adurom.com> Signed-off-by:
-
Luis R. Rodriguez authored
Here are the AR9580 1.0 initvals checksums using the Atheros initvals-tools [1]. This is useful for when we udate the initvals again with other values. It ensures that we match the same initvals used internally. The tool is documented on the wiki [2]. $ ./initvals -f ar9580-1p0 0x00000000e912711f ar9580_1p0_modes_fast_clock 0x000000004a488fc7 ar9580_1p0_radio_postamble 0x00000000f3888b02 ar9580_1p0_baseband_core 0x0000000003f783bb ar9580_1p0_mac_postamble 0x0000000094be244a ar9580_1p0_low_ob_db_tx_gain_table 0x0000000094be244a ar9580_1p0_high_power_tx_gain_table 0x0000000090be244a ar9580_1p0_lowest_ob_db_tx_gain_table 0x00000000ed9eaac6 ar9580_1p0_baseband_core_txfir_coeff_japan_2484 0x00000000c4d66d1b ar9580_1p0_mac_core 0x00000000e8e9043a ar9580_1p0_mixed_ob_db_tx_gain_table 0x000000003521a300 ar9580_1p0_wo_xlna_rx_gain_table 0x00000000301fc841 ar9580_1p0_soc_postamble 0x00000000a9a06b3a ar9580_1p0_high_ob_db_tx_gain_table 0x00000000a15ccf1b ar9580_1p0_soc_preamble 0x0000000029495000 ar9580_1p0_rx_gain_table 0x0000000037ac0ee8 ar9580_1p0_radio_core 0x00000000603a1b80 ar9580_1p0_baseband_postamble 0x000000003d8b4396 ar9580_1p0_pcie_phy_clkreq_enable_L1 0x00000000398b4396 ar9580_1p0_pcie_phy_clkreq_disable_L1 0x00000000397b4396 ar9580_1p0_pcie_phy_pll_on_clkreq [1] git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git [2] http://wireless.kernel.org/en/users/Drivers/ath9k_hw/initvals-tool Cc: David Quan <dquan@qca.qualcomm.com> Cc: Kathy Giori <kgiori@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Tested-by:
-
