This patch adds a flag "no_skb_reserve" in struct eth_dev.
So, if a peripheral driver sets the quirk_avoids_skb_reserve flag,
upper network gadget drivers (e.g. f_ncm.c) can avoid skb_reserve()
calling using the flag as well.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Some platforms (e.g. USB-DMAC on R-Car SoCs) has memory alignment
restriction. If memory alignment is not match, the usb peripheral
driver decides not to use the DMA controller. Then, the performance
is not good.

In the case of u_ether.c, since it calls skb_reserve() in rx_submit(),
it is possible to cause memory alignment mismatch.

So, this patch adds a new quirk "quirk_avoids_skb_reserve" to avoid
skb_reserve() calling in u_ether.c to improve performance.

A peripheral driver will set this flag and network gadget drivers
(e.g. f_ncm.c) will reference the flag via gadget_avoids_skb_reserve().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

trivial typo fix in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for r8a7796 (R-Car M3-W).
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Memory allocated for goku_udc device is not deallocated at error
paths in goku_probe(), because gadget_release() destructor
is not registered yet.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Trivial fix to spelling mistakes in dev_err messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

It's perfectly fine to have all configfs functions
built-in while having modular legacy gadgets. Let's
allow for that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In case our TRB ring is full, we can avoid trying to
kick transfers which won't start and just add requests
to the queue.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead, we can always rely on dwc3_calc_trbs_left()
directly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Use gadget's framework allocation function instead of directly calling
usb_ep_alloc_request().
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We should always use free_ep_req() when allocating requests with
alloc_ep_req().
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The default_length parameter of alloc_ep_req was not really necessary
and gadget drivers would almost always create an inline function to pass
the same value to len and default_len.

This patch removes that parameter and updates all calls to alloc_ep_req() to
use the new API.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].

This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The TX settings can be calibrated for particular hardware.  The
phy is reset by Linux, so this cannot be handled by the bootloader.

The TRM mentions that the maximum resistance should be used for the
DN/DP calibration in order to pass USB certification.

The values for the TX registers are poorly described in the TRM.
The meanings of the register values were taken from another
NXP-provided document:
https://community.nxp.com/message/566147#comment-566912Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jaret Cantu <jaret.cantu@timesys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The dwc3 driver expicitly looks for "usb2-phy" or "usb3-phy", but we
never noted these names in the documentation.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add revision number constants for the 3.00a and 3.10a releases.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Introduces a new FunctionFS descriptor flag named
FUNCTIONFS_CONFIG0_SETUP.

When this flag is enabled, FunctionFS userspace drivers can process
non-standard control requests in configuration 0.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

It can sometimes be necessary for gadget drivers to process non-standard
control requests, which host devices can send without having sent
USB_REQ_SET_CONFIGURATION.

Therefore, the req_match() usb_function method is enhanced with the new
parameter "config0". When a USB configuration is active, this parameter
is false. When a non-core control request is processed in
composite_setup(), without an active configuration, req_match() of the
USB functions of all available configurations which implement this
function, is called with config0=true. Then the control request gets
processed by the first usb_function instance whose req_match() returns
true.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Introduces a new FunctionFS descriptor flag named
FUNCTIONFS_ALL_CTRL_RECIP. When this flag is enabled, control requests,
which are not explicitly directed to an interface or endpoint, can be
handled.

This allows FunctionFS userspace drivers to process non-standard
control requests.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Even if the /dev/hidg* chardev is automatically created, one
has to guess which one belongs to which function. In the case
of multiple HID functions, or maybe even multiple peripherals,
this becomes difficult.

Add the dev (with major and minor number) to configfs to allow
looking up (or even creating) the right device node for each
function. This file is read-only.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When dwc3 core enters into suspend mode, the system (especially for mobile
device) may power off the dwc3 controller for power saving, that will cause
dwc3 controller lost the mode operation when resuming dwc3 core.

Thus we can move the mode setting into dwc3_core_init() function to avoid this
issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This change makes sure that the ALSA buffers are cleaned if an endpoint
becomes disabled.

Before this change, if the internal ALSA buffer did overflow, the MIDI
function would stop sending MIDI to the host.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This refactor results in a cleaner state machine code and promotes
consistency, readability, and maintanability of this driver.

This refactor state machine was well tested and it is currently running in
production code and devices.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

512 is the value used by wMaxPacketSize, as specified by the USB Spec. This
makes sure this driver uses, by default, the most optimal value for IN and OUT
endpoint requests.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The new version of alloc_ep_req() already aligns the buffer size to
wMaxPacketSize on OUT endpoints.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Using usb_ep_align() makes sure that the buffer size for OUT endpoints is
always aligned with wMaxPacketSize (512 usually). This makes sure
that no buffer has the wrong size, which can cause nasty bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Length of buffers should be of type size_t whenever possible. Altough
recommended, this change has no real practical change, unless a driver has a
uses a huge or negative buffer size - it might help find these bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

USB spec specifies wMaxPacketSize to be little endian (as other properties),
so when using this variable in the driver we should convert to the current
CPU endianness if necessary.

This patch also introduces usb_ep_align() which does always returns the
aligned buffer size for an endpoint. This is useful to be used by USB requests
allocator functions.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Introduce an attribute "inquiry_string" to the lun.

In some environments, e. g. BIOS boot menus, the inquiry string
is the only information about devices presented to the user. The
default string depends on the "cdrom" bit of the first lun as
well as the kernel version and allows no further customization.
So without access to the client it is not obvious which gadget is
active at a given point and what any of the available luns might
contain.

If "inquiry_string" is ignored or set to the empty string, the
old behavior is preserved.
Signed-off-by: Philipp Gesang <philipp.gesang@intra2net.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Rockchip platform merely enable usb3 clocks and
populate its children. So we can use this generic
glue layer to support Rockchip dwc3.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds the devicetree documentation required for Rockchip
USB3.0 core wrapper consisting of USB3.0 IP from Synopsys.

It supports DRD mode, and could operate in device mode (SS, HS, FS)
and host mode (SS, HS, FS, LS).
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.

But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>