i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This adds devicetree documentation for the bindings of the
ads7828 driver.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add support for VCT-jig parallel port I2C adapter to i2c-parport.

The adapter schematic can be found here (in the RAR file):
http://remont-aud.net/shop/22/desc/vct-jig-komplekt-dlja-samostojatelnoj-sborkiSigned-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Cadence 1.0 version has bugs which have been fixed in the cadence 1.4 version.
This patch removes the quirks present in the driver for cadence 1.4 version.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
[wsa: fixed indentation issues in r1p10_i2c_def]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Tegra I2C controller required to configure the clock divisor
register inside controller to different value based on the clock
speed. The recommended clock divisor for the I2C controller for
standard/fast mode is 0x19 and for fast-mode plus is 0x10.

Add support to configure clock divisor register of I2C controller
based on bus clock rate.

This clock divisor is supported form T114 onwards.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Once the new configuration is set on the conifg register of
I2C controller, it is require to update the CONFIG_LOAD register
to transfer the new SW configuration to actual HW internal
registers that would be used in the actual logic.

It is like, SW is programming only shadow registers through
regular configuration and when these load_config bit fields
are set to 1, it causes the regular/shadows registers
configuration transferred to the HW internal active registers.
So SW has to set these bit fields at the end of all regular
registers configuration. And these config_load bits are HW
auto-clear bits. HW clears these bit fields once the register
configuration is moved to HW internal active registers. So SW
has to wait until these bits are auto-cleared before going
for any further programming

This mechanism is supported on T124 and after this SoCs.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Patch "i2c: omap: abolish variable name confusion" triggered a
coccinelle warning which we fix here:

drivers/i2c/busses/i2c-omap.c:1333:5-24: pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at line 1334
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In case of error conditions like Arbitration lost or NACK lets signal
the waiting process.

Handle error cases in the Rx path
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently only one interrupt is serviced in the isr.
In case the multiple interrupts happen simultenously we service and ack
only one of them. Check for all the causes in the isr and service them.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently there is no slave mode support in the driver
also in the isr we just ack it and do nothing.
So disable the AAS interrupt.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Remove the busy loop  while waiting for bus busy.
Instead let the processor sleep.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently before every transfer the interrupts are disabled.
So incase the slave nacks in the middle of the transfer the
current transfer is not aborted. Upon enabling the interrupts
conditions like NACK , arbitration lost will not be masked.
Remove the disabling of the interrupts.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently before every transfer the controller is reinitialised.
We are already resetting the controller upon errors so upon every
transfer is a performance kill.
Remove the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The xiic_process is a 154 line code that runs in isr context currently
move it to thread context. Also the name xiic_process suggests that the
intension was to run in process context.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
[wsa: initialized irqreturn_t to IRQ_NONE instead of IRQ_HANDLED]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently the interrupts are disabled at the start of the
isr and enabled at the end of the isr. Remove the same.

In case the slave device NACKs the transaction while in the isr
the transfer will continue and the NACK interrupt will arrive
only after the isr is serviced.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch cleans up i2c_pxa_probe() function,

 - Use devm_ variants wherever
   This will clean both probe exit and i2c_pxa_remove() functions

 - Check platform resource before parsing any other data from DT/platform

 - Use dev_err on failure from i2c_add_numbered_adapter()

 - Use pr_info instead of printk for KERN_INFO
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: removed unneeded error prinout after devm_ioremap_resource]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Update i2c_pxa_scream_blue_murder() fn to print more information
in case of error.
Also, use dev_err variants instead of printk.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Fix below warning message, coming from 64 bit toolchain.

drivers/i2c/busses/i2c-pxa.c:1237:15:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Yipeng Yao <ypyao@marvell.com>
[vaibhav.hiremath@linaro.org: Updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In case of timeout in pio mode of operation return I2C_RETRY.
This behavior will be same as interrupt mode of operation.
Signed-off-by: Shouming Wang <wangshm@marvell.com>
[vaibhav.hiremath@linaro.org: Updated changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Normally i2c controller works as master, so slave addr is not needed, or
it will impact some slave device (eg. ST NFC chip) i2c accesses, because
it has the same i2c address with controller.

For example,
On the pxa1928 based platform, where PMIC (88pm860) is present @0x30
address on TWSI0 interface, and if we set 0x30 as a slave address in
pxa1928 TWSI0 module, all the transactions towards PMIC would go for toss.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

During suspend there may still be some i2c access happening, as the
interrupt is shared between multiple drivers.
And if we don't keep i2c irq ON, there may be i2c access timeout if
i2c is in irq mode of operation.
Signed-off-by: Raul Xiong <xjian@marvell.com>
Signed-off-by: Xiaofan Tian <tianxf@marvell.com>
[vaibhav.hiremath@linaro.org: updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

We have a driver now for IIC, so disable reset for them.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

we're about to remove the module, so we can't
really schedule a PM transition in the future,
we must wait for it to finish.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

struct device pointers are usually called
dev. Calling our struct omap_i2c_dev pointers
also dev has caused enough confusion.

This is the result of a few simple sed rules
to convert all struct omap_i2c_dev pointers
to be called omap instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

there's no need to fetch the platform_device
in order to dereference it back to the dev
pointer to access drvdata, we can use
dev_get_drvdata() instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Start using pr_fmt and convert all remaining printk to use
pr_* family of macros.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
[wsa: remove print on kzalloc failure]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Now parport is using device model so use dev_* macros instead of printk.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull input subsystem fixes from Dmitry Torokhov:
 "Just small ALPS and Elan touchpads, and other driver fixups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elantech - add special check for fw_version 0x470f01 touchpad
  Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning
  Input: alps - only Dell laptops have separate button bits for v2 dualpoint sticks
  Input: axp20x-pek - add module alias
  Input: turbografx - fix potential out of bound access

Pull MIPS fixes from Ralf Baechle:
 "Another round of MIPS fixes for 4.2.  No area does particularly stand
  out but we have a two unpleasant ones:

   - Kernel ptes are marked with a global bit which allows the kernel to
     share kernel TLB entries between all processes.  For this to work
     both entries of an adjacent even/odd pte pair need to have the
     global bit set.  There has been a subtle race in setting the other
     entry's global bit since ~ 2000 but it take particularly
     pathological workloads that essentially do mostly vmalloc/vfree to
     trigger this.

     This pull request fixes the 64-bit case but leaves the case of 32
     bit CPUs with 64 bit ptes unsolved for now.  The unfixed cases
     affect hardware that is not available in the field yet.

   - Instruction emulation requires loading instructions from user space
     but the current fast but simplistic approach will fail on pages
     that are PROT_EXEC but !PROT_READ.  For this reason we temporarily
     do not permit this permission and will map pages with PROT_EXEC |
     PROT_READ.

  The remainder of this pull request is more or less across the field
  and the short log explains them well"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Make set_pte() SMP safe.
  MIPS: Replace add and sub instructions in relocate_kernel.S with addiu
  MIPS: Flush RPS on kernel entry with EVA
  Revert "MIPS: BCM63xx: Provide a plat_post_dma_flush hook"
  MIPS: BMIPS: Delete unused Kconfig symbol
  MIPS: Export get_c0_perfcount_int()
  MIPS: show_stack: Fix stack trace with EVA
  MIPS: do_mcheck: Fix kernel code dump with EVA
  MIPS: SMP: Don't increment irq_count multiple times for call function IPIs
  MIPS: Partially disable RIXI support.
  MIPS: Handle page faults of executable but unreadable pages correctly.
  MIPS: Malta: Don't reinitialise RTC
  MIPS: unaligned: Fix build error on big endian R6 kernels
  MIPS: Fix sched_getaffinity with MT FPAFF enabled
  MIPS: Fix build with CONFIG_OF=y for non OF-enabled targets
  CPUFREQ: Loongson2: Fix broken build due to incorrect include.

Pull btrfs fix from Chris Mason:
 "We have a btrfs quota regression fix.

  I merged this one on Thursday and have run it through tests against
  current master.

  Normally I wouldn't have sent this while you were finalizing rc6, but
  I'm feeding mosquitoes in the adirondacks next week, so I wanted to
  get this one out before leaving.  I'll leave longer tests running and
  check on things during the week, but I don't expect any problems"

* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: qgroup: Fix a regression in qgroup reserved space.

Pull thermal management fixes from Zhang Rui:
 "Specifics:

   - fix an error that "weight_attr" sysfs attribute is not removed
     while unbinding.  From: Viresh Kumar.

   - fix power allocator governor tracing to return the real request.
     From Javi Merino.

   - remove redundant owner assignment of hisi platform thermal driver.
     From Krzysztof Kozlowski.

   - a couple of small fixes of Exynos thermal driver.  From Krzysztof
     Kozlowski and Chanwoo Choi"

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: Drop owner assignment from platform_driver
  thermal: exynos: Remove unused code related to platform_data on probe()
  thermal: exynos: Add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF
  thermal: exynos: Disable the regulator on probe failure
  thermal: power_allocator: trace the real requested power
  thermal: remove dangling 'weight_attr' device file

Pull ARC fixes from Vineet Gupta:
 "Here's a late pull request for accumulated ARC fixes which came out of
  extended testing of the new ARCv2 port with LTP etc.  llock/scond
  livelock workaround has been reviewed by PeterZ.  The changes look a
  lot but I've crafted them into finer grained patches for better
  tracking later.

  I have some more fixes (ARC Futex backend) ready to go but those will
  have to wait for tglx to return from vacation.

  Summary:
   - Enable a reduced config of HS38 (w/o div-rem, ll64...)
   - Add software workaround for LLOCK/SCOND livelock
   - Fallout of a recent pt_regs update"

* tag 'arc-v4.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARCv2: spinlock/rwlock/atomics: reduce 1 instruction in exponential backoff
  ARC: Make pt_regs regs unsigned
  ARCv2: spinlock/rwlock: Reset retry delay when starting a new spin-wait cycle
  ARCv2: spinlock/rwlock/atomics: Delayed retry of failed SCOND with exponential backoff
  ARC: LLOCK/SCOND based rwlock
  ARC: LLOCK/SCOND based spin_lock
  ARC: refactor atomic inline asm operands with symbolic names
  Revert "ARCv2: STAR 9000837815 workaround hardware exclusive transactions livelock"
  ARCv2: [axs103_smp] Reduce clk for Quad FPGA configs
  ARCv2: Fix the peripheral address space detection
  ARCv2: allow selection of page size for MMUv4
  ARCv2: lib: memset: Don't assume 64-bit load/stores
  ARCv2: lib: memcpy: Missing PREFETCHW
  ARCv2: add knob for DIV_REV in Kconfig
  ARC/time: Migrate to new 'set-state' interface

Pull virtio fix from Michael Tsirkin:
 "A last minute fix for the new virtio input driver.  It seems pretty
   obvious, and the problem it's fixing would be quite hard to debug"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio-input: reset device and detach unused during remove

Pull device mapper fixes from Mike Snitzer:

 - stable fix for a dm_merge_bvec() regression on 32 bit Fedora systems.

 - fix for a 4.2 DM thinp discard regression due to inability to
   properly delete a range of blocks in a data mapping btree.

* tag 'dm-4.2-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm btree remove: fix bug in remove_one()
  dm: fix dm_merge_bvec regression on 32 bit systems

Pull sound fixes from Takashi Iwai:
 "The only bulk changes in this request is ABI updates for ASoC topology
  API.  It's a new API that was introduced in 4.2, and we'd like to
  avoid ABI change after the release, so it's taken now.  As there is no
  real in-tree user for this API, it should be fairly safe.

  Other than that, the usual small fixes are found in various drivers:
  ASoC cs4265, rt5645, intel-sst, firewire, oxygen and HD-audio"

* tag 'sound-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: topology: Add private data type and bump ABI version to 3
  ASoC: topology: Add ops support to byte controls UAPI
  ASoC: topology: Update TLV support so we can support more TLV types
  ASoC: topology: add private data to manifest
  ASoC: topology: Add subsequence in topology
  ALSA: hda - one Dell machine needs the headphone white noise fixup
  ALSA: fireworks/firewire-lib: add support for recent firmware quirk
  Revert "ALSA: fireworks: add support for AudioFire2 quirk"
  ASoC: topology: fix typo in soc_tplg_kcontrol_bind_io()
  ALSA: HDA: Dont check return for snd_hdac_chip_readl
  ALSA: HDA: Fix stream assignment for host in decoupled mode
  ASoC: rt5645: Fix lost pin setting for DMIC1
  ALSA: oxygen: Fix logical-not-parentheses warning
  ASoC: Intel: sst_byt: fix initialize 'NULL device *' issue
  ASoC: Intel: haswell: fix initialize 'NULL device *' issue
  ASoC: cs4265: Fix setting dai format for Left/Right Justified

Merge tag 'hwmon-for-linus-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Export module alias information in g762 and nct7904 to support
   auto-loading.

 - Blacklist Dell Studio XPS 8100 in dell-smm to fix fan control
   problems.

* tag 'hwmon-for-linus-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (g762) Export OF module alias information
  hwmon: (nct7904) Export I2C module alias information
  hwmon: (dell-smm) Blacklist Dell Studio XPS 8100

Pull USB fixes from Greg KH:
 "Here are some USB and PHY fixes for 4.2-rc6 that resolve some reported
  issues.

  All of these have been in the linux-next tree for a while, full
  details on the patches are in the shortlog below"

* tag 'usb-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  ARM: dts: dra7: Add syscon-pllreset syscon to SATA PHY
  drivers/usb: Delete XHCI command timer if necessary
  xhci: fix off by one error in TRB DMA address boundary check
  usb: udc: core: add device_del() call to error pathway
  phy: ti-pipe3: i783 workaround for SATA lockup after dpll unlock/relock
  phy-sun4i-usb: Add missing EXPORT_SYMBOL_GPL for sun4i_usb_phy_set_squelch_detect
  USB: sierra: add 1199:68AB device ID
  usb: gadget: f_printer: actually limit the number of instances
  usb: gadget: f_hid: actually limit the number of instances
  usb: gadget: f_uac2: fix calculation of uac2->p_interval
  usb: gadget: bdc: fix a driver crash on disconnect
  usb: chipidea: ehci_init_driver is intended to call one time
  USB: qcserial: Add support for Dell Wireless 5809e 4G Modem
  USB: qcserial/option: make AT URCs work for Sierra Wireless MC7305/MC7355