This patch (as892) removes the "locktree" routine from the hub driver.
It currently is used in only one place, by a single kernel thread;
hence it isn't doing any good.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This revised patch (as891b) removes two unnecessary references to
intf->dev.power.power_state from usb-storage, and replaces a reference
to root_hub->dev.power.power_state with a check of hcd->state.  This
is in preparation for the removal of dev.power.power_state, which is
already deprecated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as889) prevents the hub driver from trying to resume a
port when there is a new connection.  For one thing, the resume is not
needed -- the upcoming port reset will clear the suspend feature
automatically.  For another, on some systems the resume fails and
causes problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as885) moves the root-hub bus_suspend() and bus_resume()
method calls from the hub driver's suspend and resume methods into the
usb_generic driver methods, where they make just as much sense.

Their old locations were not fully correct.  For example, in a kernel
compiled without CONFIG_USB_SUSPEND, if one were to do:

	echo -n 1-0:1.0 >/sys/bus/usb/drivers/hub/unbind

to unbind the hub driver from a root hub, there would then be no way
to suspend that root hub.  Attempts to put the system to sleep would
fail; the USB controller driver would refuse to suspend because the
root hub was still active.

The patch also makes a very slight change in the way devices with no
driver are handled during suspend.  Rather than doing a standard USB
port-suspend directly, now the suspend routine in usb_generic is
called.  In practice this should never affect anyone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as884) finally implements the time-saving semantics
possible with the Power Management FREEZE and PRETHAW events.  Their
proper handling requires only that devices be quiesced, with
interrupts and DMA turned off; non-root USB devices don't actually
need to be put in a suspended state.  The patch checks and avoids
doing the suspend call when possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as880) strives to keep the PM core's idea of a USB
interface's power state in synch with usbcore's own idea.  In the end
this doesn't really matter, but it's better to be consistent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes the problem that accesses NULL pointer
when disconnected a cable while play music with usb-speaker.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I would like to submit Renesas R8A66597 USB HCD driver.

R8A66597 is Renesas USB 2.0 host and peripheral combined
controller device originally designed for embedded products.
As a limitation of this device, it does not support externel
hub more than 2 tier, and cannot communicate with a USB
device more than 10. Then this device is not compatible with
EHCI and/or OHCI, I wrote driver support patch based on
sl811 code.

This driver has the following unique specifications:
- Implement transfer timeout to share one pipe with plural endpoint.
- Detach detection of a USB device connected to externel hub.

The driver has been tested external hub, usb-hdd, usb-cdrom,
usb-speaker, mice, keyboard, and usbtest driver.

Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes the problem that used SA_* flags.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I would like to submit Renesas M66592 udc driver.

The M66592 is Renesas USB 2.0 peripheral controller.
This controller supports USB high-speed.

The driver has been tested Gadget Zero, Ethernet Gadget,
File-backed Storage Gadget, and passed usbtest script.

Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add support for Keyspan adapters: USA-49WG and USA-28XG
Signed-off-by: Lucy P. McCoy <lucy@keyspan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This changes the format of unknown status values to be less verbose and
uses an array instead of several different snprintf calls. Since only
enum values are assigned to it, poll_state is changed from int to enum.
Use abs() for dB values instead of two almost identical return lines.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch implements supports for EHCI controllers whose in-memory
data structures are represented in big-endian format. This is needed
(unfortunately) for the AMCC PPC440EPx SoC EHCI controller; the EHCI
spec doesn't specify little-endian format, although that's what most
other implementations use.

The guts of the patch are to introduce the hc32 type and change all
references from le32 to hc32.  All access routines are converted from
cpu_to_le32(...) to cpu_to_hc32(ehci, ...) and similar for the other
"direction".  (This is the same approach used with OHCI.)

David fixed:
	Whitespace fixes; refresh against ehci cpufreq patch; move glue
	for that PPC driver to the patch adding it; fix free symbol
	capture bugs in modified "constant" macros; and make "hc32" etc
	be "le32" unless we really need the BE options, so "sparse" can
	do some real good.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

EHCI controllers that don't cache enough microframes can get MMF errors
when CPU frequency changes occur between the start and completion of
split interrupt transactions, due to delays in reading main memory
(caused by CPU cache snoop delays).

This patch adds a cpufreq notifier to the EHCI driver that will
inactivate split interrupt transactions during frequency transitions.
It was tested on Intel ICH7 and Serverworks/Broadcom HT1000 EHCI
controllers.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this implements generic support for suspend/resume for usb serial.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch supports LSI/Engenio devices in RDAC mode. Like dm-emc
it requires userspace support. In your multipath.conf file you must have:

path_checker            rdac
hardware_handler        "1 rdac"
prio_callout		"/sbin/mpath_prio_tpc /dev/%n"

And you also then must have a updated multipath tools release which
has rdac support.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When writing to a mirror, the log must be updated first.  Failure
to update the log could result in the log not properly reflecting
the state of the mirror if the machine should crash.

We change the return type of the rh_flush function to give us
the ability to check if a log write was successful.  If the
log write was unsuccessful, we fail the writes to avoid the
case where the log does not properly reflect the state of the
mirror.

A follow-up patch - which is dependent on the ability to
requeue I/O's to core device-mapper - will requeue the I/O's
for retry (allowing the mirror to be reconfigured.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Device-mapper mirroring currently takes a best effort approach to
recovery - failures during mirror synchronization are completely ignored.
This means that regions are marked 'in-sync' and 'clean' and removed
from the hash list.  Future reads and writes that query the region
will incorrectly interpret the region as in-sync.

This patch handles failures during the recovery process.  If a failure
occurs, the region is marked as 'not-in-sync' (aka RH_NOSYNC) and added
to a new list 'failed_recovered_regions'.

Regions on the 'failed_recovered_regions' list are not marked as 'clean'
upon removal from the list.  Furthermore, if the DM_RAID1_HANDLE_ERRORS
flag is set, the region is marked as 'not-in-sync'.  This action prevents
any future read-balancing from choosing an invalid device because of the
'not-in-sync' status.

If "handle_errors" is not specified when creating a mirror (leaving the
DM_RAID1_HANDLE_ERRORS flag unset), failures will be ignored exactly as they
would be without this patch.  This is to preserve backwards compatibility with
user-space tools, such as 'pvmove'.  However, since future read-balancing
policies will rely on the correct sync status of a region, a user must choose
"handle_errors" when using read-balancing.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add ratelimit extension to dm logging macros.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch causes device-mapper to reject any barrier requests.  This is done
since most of the targets won't handle this correctly anyway.  So until the
situation improves it is better to reject these requests at the first place.
Since barrier requests won't get to the targets, the checks there can be
removed.

Cc: stable@kernel.org
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A clear_region function is permitted to block (in practice, rare) but gets
called in rh_update_states() with a spinlock held.

The bits being marked and cleared by the above functions are used
to update the on-disk log, but are never read directly.  We can
perform these operations outside the spinlock since the
bits are only changed within one thread viz.
   - mark_region in rh_inc()
   - clear_region in rh_update_states().

So, we grab the clean_regions list items via list_splice() within the
spinlock and defer clear_region() until we iterate over the list for
deletion - similar to how the recovered_regions list is already handled.
We then move the flush() call down to ensure it encapsulates the changes
which are done by the later calls to clear_region().
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Allow invalid snapshots to be activated instead of failing.

This allows userspace to reinstate any given snapshot state - for
example after an unscheduled reboot - and clean up the invalid snapshot
at its leisure.

Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Process persistent exception store metadata IOs in a separate thread.

A snapshot may become invalid while inside generic_make_request().
A synchronous write is then needed to update the metadata while still
inside that function.  Since the introduction of
md-dm-reduce-stack-usage-with-stacked-block-devices.patch this has to
be performed by a separate thread to avoid deadlock.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

bio_alloc_bioset() will return NULL if 'num_vecs' is too large.
Use bio_get_nr_vecs() to get estimation of maximum number.

Cc: stable@kernel.org
Signed-off-by: "Jun'ichi Nomura" <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix mirror status line broken in dm-log-report-fault-status.patch:
  - space missing between two words
  - placeholder ("0") required for compatibility with a subsequent patch
  - incorrect offset parameter

Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove explicit module name from messages as the macro now includes it
automatically.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use setup_timer().
Replace semaphore with mutex.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use new KMEM_CACHE() macro and make the newly-exposed structure names more
meaningful.  Also remove some superfluous casts and inlines (let a modern
compiler be the judge).
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove dubious prefetch from bio_list_for_each() macro.

Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (50 commits)
  [ARM] sa1100: remove boot time RTC initialisation
  [ARM] sa1100: stop doing our own rtc management over suspend
  [ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
  [ARM] 4473/2:  Take the HWCAP definitions out of the elf.h file
  [ARM] pxa: move platform devices to separate header file
  [ARM] pxa: move device registration into CPU-specific file
  [ARM] pxa: remove boot time RTC initialisation
  [ARM] pxa: stop doing our own rtc management over suspend
  [ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
  [ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
  [ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
  [ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
  [ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
  [ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
  [ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS
  [ARM] 4434/1: PXA: remove PXA_IRQ_SKIP
  [ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
  [ARM] pxa: move pm_ops structure into CPU specific files
  [ARM] pxa: introduce cpu_is_pxaXXX macros
  [ARM] pxa: remove MMC register defines from pxa-regs.h
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  security: unexport mmap_min_addr
  SELinux: use SECINITSID_NETMSG instead of SECINITSID_UNLABELED for NetLabel
  security: Protection for exploiting null dereference using mmap
  SELinux: Use %lu for inode->i_no when printing avc
  SELinux: allow preemption between transition permission checks
  selinux: introduce schedule points in policydb_destroy()
  selinux: add selinuxfs structure for object class discovery
  selinux: change sel_make_dir() to specify inode counter.
  selinux: rename sel_remove_bools() for more general usage.
  selinux: add support for querying object classes and permissions from the running policy

* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Fix sysfs_create_file return value handling
  [CPUFREQ] ondemand: fix tickless accounting and software coordination bug
  [CPUFREQ] ondemand: add a check to avoid negative load calculation
  [CPUFREQ] Keep userspace governor quiet when it is not being used
  [CPUFREQ] Longhaul - Proper register access
  [CPUFREQ] Kconfig powernow-k8 driver should depend on ACPI P-States driver
  [CPUFREQ] Longhaul - Replace ACPI functions with direct I/O
  [CPUFREQ] Longhaul - Remove duplicate multipliers
  [CPUFREQ] Longhaul - Embedded "conservative"
  [CPUFREQ] acpi-cpufreq: Proper ReadModifyWrite of PERF_CTL MSR
  [CPUFREQ] check return value of sysfs_create_file
  [CPUFREQ] Longhaul - Check ACPI "BM DMA in progress" bit
  [CPUFREQ] Longhaul - Move old_ratio to correct place
  [CPUFREQ] Longhaul - VT8237 support
  [CPUFREQ] Longhaul - Use all kinds of support
  [CPUFREQ] powernow-k8: clarify number of cores.

* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
  [AGPGART] Hand off AGP maintainence.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Support multiple CPUs going through OS_MCA
  [IA64] silence GCC ia64 unused variable warnings
  [IA64] prevent MCA when performing MMIO mmap to PCI config space
  [IA64] add sn_register_pmi_handler oemcall
  [IA64] Stop bit for brl instruction
  [IA64] SN: Correct ROM resource length for BIOS copy
  [IA64] Don't set psr.ic and psr.i simultaneously

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
  PCI: Only build PCI syscalls on architectures that want them
  PCI: limit pci_get_bus_and_slot to domain 0
  PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
  PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
  PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
  PCI: hotplug: pciehp: wait for 1 second after power off slot
  PCI: pci_set_power_state(): check for PM capabilities earlier
  PCI: cpci_hotplug: Convert to use the kthread API
  PCI: add pci_try_set_mwi
  PCI: pcie: remove SPIN_LOCK_UNLOCKED
  PCI: ROUND_UP macro cleanup in drivers/pci
  PCI: remove pci_dac_dma_... APIs
  PCI: pci-x-pci-express-read-control-interfaces cleanups
  PCI: Fix typo in include/linux/pci.h
  PCI: pci_ids, remove double or more empty lines
  PCI: pci_ids, add atheros and 3com_2 vendors
  PCI: pci_ids, reorder some entries
  PCI: i386: traps, change VENDOR to DEVICE
  PCI: ATM: lanai, change VENDOR to DEVICE
  PCI: Change all drivers to use pci_device->revision
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (61 commits)
  sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes
  sysfs: make directory dentries and inodes reclaimable
  sysfs: implement sysfs_get_dentry()
  sysfs: move sysfs_drop_dentry() to dir.c and make it static
  sysfs: restructure add/remove paths and fix inode update
  sysfs: use sysfs_mutex to protect the sysfs_dirent tree
  sysfs: consolidate sysfs spinlocks
  sysfs: make kobj point to sysfs_dirent instead of dentry
  sysfs: implement sysfs_find_dirent() and sysfs_get_dirent()
  sysfs: implement SYSFS_FLAG_REMOVED flag
  sysfs: rename sysfs_dirent->s_type to s_flags and make room for flags
  sysfs: make sysfs_drop_dentry() access inodes using ilookup()
  sysfs: Fix oops in sysfs_drop_dentry on x86_64
  sysfs: use singly-linked list for sysfs_dirent tree
  sysfs: slim down sysfs_dirent->s_active
  sysfs: move s_active functions to fs/sysfs/dir.c
  sysfs: fix root sysfs_dirent -> root dentry association
  sysfs: use iget_locked() instead of new_inode()
  sysfs: reorganize sysfs_new_indoe() and sysfs_create()
  sysfs: fix parent refcounting during rename and move
  ...

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (21 commits)
  libata: remove irq_on from ata_bus_reset() and ata_std_postreset()
  ata_piix: kill incorrect invalid map value warning
  libata: add another Maxtor drive with broken NCQ to the list
  [libata] sata_mv: Fix and clean up per-chip-generation tests
  [libata] sata_mv: Convert to new exception handling (EH) infrastructure
  [libata] sata_mv: minor bug fixes, enhancements, and cleanups (prep for new EH)
  [libata] sata_mv: Minor cleanups and renaming, preparing for new EH & NCQ
  libata-link: add PMP related ATA constants
  libata-link: separate out ata_eh_handle_dev_fail()
  pata_hpt3x3: fix DMA Kconfig option to actually have a hope of working
  Add Hitachi HDS7250SASUN500G 0621KTAWSD to NCQ blacklist
  pata_scc.c: Workaround for errata A308
  libata: add FUJITSU MHV2080BH to NCQ blacklist
  pata_hpt3x3: major reworking and testing
  libata: clean up horkage handling
  libata: quirk IOMEGA ZIP 250 ATAPI FLOPPY
  libata: simplify PCI legacy SFF host handling
  pata_mpc52xx: suspend/resume support
  sata_promise: SATA hotplug support, take 2
  pata_sis: FIFO whack
  ...

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (183 commits)
  [TG3]: Update version to 3.78.
  [TG3]: Add missing NVRAM strapping.
  [TG3]: Enable auto MDI.
  [TG3]: Fix the polarity bit.
  [TG3]: Fix irq_sync race condition.
  [NET_SCHED]: ematch: module autoloading
  [TCP]: tcp probe wraparound handling and other changes
  [RTNETLINK]: rtnl_link: allow specifying initial device address
  [RTNETLINK]: rtnl_link API simplification
  [VLAN]: Fix MAC address handling
  [ETH]: Validate address in eth_mac_addr
  [NET]: Fix races in net_rx_action vs netpoll.
  [AF_UNIX]: Rewrite garbage collector, fixes race.
  [NETFILTER]: {ip, nf}_conntrack_sctp: fix remotely triggerable NULL ptr dereference (CVE-2007-2876)
  [NET]: Make all initialized struct seq_operations const.
  [UDP]: Fix length check.
  [IPV6]: Remove unneeded pointer idev from addrconf_cleanup().
  [DECNET]: Another unnecessary net/tcp.h inclusion in net/dn.h
  [IPV6]: Make IPV6_{RECV,2292}RTHDR boolean options.
  [IPV6]: Do not send RH0 anymore.
  ...

Fixed up trivial conflict in Documentation/feature-removal-schedule.txt
manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The RTC library code contains everything necessary to set the
system time from the RTC; for similar reasons as the previous
commit, it's far better to let the RTC library code sort this
out rather than implement something which might not be
appropriate for everyone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>