Before sending a command to the ASIC, set version properly.
This is necessary for the ARM firmware to send correct data to the driver.
This also fixes a bug in certain skews of the ASIC where the statistics
are misreported.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfrm_state_clone calls kfree instead of xfrm_state_put to free
a failed state.  Depending on the state of the failed state, it
can cause leaks to things like module references.

All states should be freed by xfrm_state_put past the point of
xfrm_init_state.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ipcomp_tunnel_attach fails we will call ipcomp_destroy twice.
This may lead to double-frees on certain structures.

As there is no reason to explicitly call ipcomp_destroy, this patch
removes it from ipcomp*.c and lets the standard xfrm_state destruction
take place.

This is based on the discovery and patch by Alexey Dobriyan.
Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like an oversight in GRO design.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to have the WUS register set to all 1's in order for the hardware
to be capable of ever waking up.  Set it here in the ixgbe_probe().
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 82598 has an erratum that receipt of pause frames at 1G
could lead to a Tx Hang.  To avoid this this patch disables
Rx FC while at 1G speed for all 82598 parts.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Steve Hodgson <shodgson@solarflare.com>

Commit 357d46a1 "sfc: QT202x: Remove
unreliable MMD check at initialisation" broke initialisation of the
SFE4002.  efx_mdio_reset_mmd() returns a positive value rather than 0
on success.  The above commit causes this value to be propagated up
by qt202x_reset_phy(), which is treated as a failure by its callers.
Change qt202x_reset_phy() to return 0 if successful.

The PCI layer treats >0 as "fail, but please call remove() anyway",
which means that unloading the driver would cause a crash.  Add a
WARN_ON() on the failure path of efx_pci_probe() to provide early
warning if there are any other cases where we do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For hardware with IEEE80211_HW_HAS_RATE_CONTROL the rate controller is not
initialized. However, calling functions such as ieee80211_beacon_get result
in the rate_control_get_rate function getting called, which is accessing
(in this case uninitialized) rate control structures unconditionally.

Fix by exiting the function before setting the rates for HW with
IEEE80211_HW_HAS_RATE_CONTROL set. The initialization of the ieee80211_tx_info
struct is intentionally still executed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently we treat IGMPv3 reports as if it were an IGMPv2/v1 report.
This is broken as IGMPv3 reports are formatted differently.  So we
end up suppressing a bogus multicast group (which should be harmless
as long as the leading reserved field is zero).

In fact, IGMPv3 does not allow membership report suppression so
we should simply ignore IGMPv3 membership reports as a host.

This patch does exactly that.  I kept the case statement for it
so people won't accidentally add it back thinking that we overlooked
this case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previous patch "use paged Rx" broke AMSDU Rx functionality. If an AP
sends out A-MSDU packets the station will crash.  Fix it by linearizing
skbuff for AMSDU packet before handing it to mac80211 since mac80211
doesn't support paged skbuff.

This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2155Reported-by: Norbert Preining <preining@logic.at>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make sure, that TCP has a nonzero RTT estimation after three-way
handshake. Currently, a listening TCP has a value of 0 for srtt,
rttvar and rto right after the three-way handshake is completed
with TCP timestamps disabled.
This will lead to corrupt RTO recalculation and retransmission
flood when RTO is recalculated on backoff reversion as introduced
in "Revert RTO on ICMP destination unreachable"
(f1ecd5d9).
This behaviour can be provoked by connecting to a server which
"responds first" (like SMTP) and rejecting every packet after
the handshake with dest-unreachable, which will lead to softirq
load on the server (up to 30% per socket in some tests).

Thanks to Ilpo Jarvinen for providing debug patches and to
Denys Fedoryshchenko for reporting and testing.

Changes since v3: Removed bad characters in patchfile.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes two potential races in the velocity driver:

* Move the ACK and error handler to the interrupt handler. This fixes a
  potential race with shared interrupts when the other device interrupts
  before the NAPI poll handler has finished. As the velocity driver hasn't
  acked it's own interrupt, it will then steal the interrupt from the
  other device.

* Use spin_lock_irqsave in velocity_poll. In the current code, the
  interrupt handler will deadlock if e.g., the NAPI poll handler is
  executing when an interrupt (for another device) comes in since it
  tries to take the already held lock.

  Also unlock the spinlock only after enabling the interrupt in
  velocity_poll.

The error path is moved to the interrupt handler since this is where the
ISR is checked now.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Anders Grafstrom <anders.grafstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

velocity_set_coalesce touches ISR and some other sensitive registers not
covered by the rtnl lock, so take the velocity spinlock.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new RTL8187B device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The wrong pointer was tested.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Test the value that was just allocated rather than the previously tested one.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@

if (x == NULL || ...) {
    ... when forall
    return ...; }
... when != goto l;
    when != x = e
    when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

During the rc period, patches that are not bugfixes
should be done using the net-next tree.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The action modules have been prefixed with 'act_', but the Kconfig
description was not changed.
Signed-off-by: Jan Luebbe <jluebbe@debian.org>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify the HW checksum state for frames handed to GRO processing.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel bugzilla #15239

On some workloads, it is quite possible to get a huge dst list to
process in dst_gc_task(), and trigger soft lockup detection.

Fix is to call cond_resched(), as we run in process context.
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reinette found the reason for the warnings that
happened occasionally when a hw-offloaded scan
finished; her description of the problem:

  mac80211 will defer the handling of scan requests if it is
  busy with management work at the time. The scan requests
  are deferred and run after the work has completed. When
  this occurs there are currently two problems.

  * The scan request for hardware scan is not fully populated
    with the band and channels to scan not initialized.

  * When the scan is queued the state is not correctly updated
    to reflect that a scan is in progress. The problem here is
    that when the driver completes the scan and calls
    ieee80211_scan_completed() a warning will be triggered
    since mac80211 was not aware that a scan was in progress.

The reason is that the queued scan work will start
the hw scan right away when the hw_scan_req struct
has already been allocated. However, in the first
pass it will not have been filled, which happens
at the same time as setting the bits. To fix this,
simply move the allocation after the pending work
test as well, so that the first iteration of the
scan work will call __ieee80211_start_scan() even
in the hardware scan case.
Bug-identified-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_set_rxon_ht() only get called in iwl_post_associate(); which cause
possible incorrect ht configuration. Adding the call in iwl_mac_config() if
IEEE80211_CONF_CHANGE_CHANNEL flag is set to re-configure and send rxon
command.

Fixes
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2146Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We only reply to probe request if either the requested SSID is the
broadcast SSID or if the requested SSID matches our own SSID. This
latter case was not properly handled since we were replying to different
SSID with the same length as our own SSID.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As noticed by Jon Masters <jonathan@jonmasters.org>, the conntrack hash
size is global and not per namespace, but modifiable at runtime through
/sys/module/nf_conntrack/hashsize. Changing the hash size will only
resize the hash in the current namespace however, so other namespaces
will use an invalid hash size. This can cause crashes when enlarging
the hashsize, or false negative lookups when shrinking it.

Move the hash size into the per-namespace data and only use the global
hash size to initialize the per-namespace value when instanciating a
new namespace. Additionally restrict hash resizing to init_net for
now as other namespaces are not handled currently.

Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

As per C99 6.2.4(2) when temporary table data goes out of scope,
the behaviour is undefined:

	if (compat) {
		struct foo tmp;
		...
		private = &tmp;
	}
	[dereference private]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>

Expectation hashtable size was simply glued to a variable with no code
to rehash expectations, so it was a bug to allow writing to it.
Make "expect_hashsize" readonly.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>

nf_conntrack_cachep is currently shared by all netns instances, but
because of SLAB_DESTROY_BY_RCU special semantics, this is wrong.

If we use a shared slab cache, one object can instantly flight between
one hash table (netns ONE) to another one (netns TWO), and concurrent
reader (doing a lookup in netns ONE, 'finding' an object of netns TWO)
can be fooled without notice, because no RCU grace period has to be
observed between object freeing and its reuse.

We dont have this problem with UDP/TCP slab caches because TCP/UDP
hashtables are global to the machine (and each object has a pointer to
its netns).

If we use per netns conntrack hash tables, we also *must* use per netns
conntrack slab caches, to guarantee an object can not escape from one
namespace to another one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
[Patrick: added unique slab name allocation]
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>

As discovered by Jon Masters <jonathan@jonmasters.org>, the "untracked"
conntrack, which is located in the data section, might be accidentally
freed when a new namespace is instantiated while the untracked conntrack
is attached to a skb because the reference count it re-initialized.

The best fix would be to use a seperate untracked conntrack per
namespace since it includes a namespace pointer. Unfortunately this is
not possible without larger changes since the namespace is not easily
available everywhere we need it. For now move the untracked conntrack
initialization to the init_net setup function to make sure the reference
count is not re-initialized and handle cleanup in the init_net cleanup
function to make sure namespaces can exit properly while the untracked
conntrack is in use in other namespaces.

Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The report descriptor is read by user space (via the Service
Discovery Protocol), so it is only available during the ioctl
to connect. However, the HID probe function that needs the
descriptor might not be called until a specific module is
loaded. Keep a copy of the descriptor so it is available for
later use.
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Add missing try_to_freeze() to one of the pktgen_thread_worker() code
paths so that it doesn't block suspend/hibernation.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=15006Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Ciprian Dorin Craciun <ciprian.craciun@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change corrects an issue that will cause false hangs when using either
82575 or 82580 in legacy interrupt mode.  The issue is caused when there is
a slow traffic flow and an "ethtool -r" is executed while using legacy or
MSI interrupts.  MSI-X is not affected by this issue due to the fact that
we were already reconfiguring the vectors after reset.

If possible it would be best to push this for net-2.6 since it is resolving
a bug but if that is not possible then net-next-2.6 will be fine.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One ioctl has been forgotten when the BKL was push down into irnet_ppp
ioctl function.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing unlock_kernel in one ioctl operation.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

a developer had complained of getting lots of warnings:

"eth16 selects TX queue 98, but real number of TX queues is 64"

http://www.mail-archive.com/e1000-devel@lists.sourceforge.net/msg02200.html

As there was no follow up on that bug, I am submitting this
patch assuming that the other return points will not return
invalid txq's, and also that this fixes the bug (not tested).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit e5a43549 (ixgbe: remove
skb_dma_map/unmap calls from driver) looks to have introduced a bug in
ixgbe_tx_map. If we get an error from a PCI DMA call, we loop backwards
through count until it becomes -1 and return that.

The caller of ixgbe_tx_map expects 0 on error, so return that instead.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>