We don't create a connector but let panel_bridge handle that so there's
no point in rejecting DRM_BRIDGE_ATTACH_NO_CONNECTOR.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/8b6545b991afce6add0a24f5f5d116778b0cb763.1595096667.git.agx@sigxcpu.org

Fine tune the HBP and HFP to avoid the dot noise on the left and right edges.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714123332.37609-1-jitao.shi@mediatek.com

On boe_nv133fhm_n62 (and presumably on boe_nv133fhm_n61) a scope shows
a small spike on the HPD line right when you power the panel on.  The
picture looks something like this:

         +--------------------------------------
         |
         |
         |
Power ---+
                                           +---
                                           |
              ++                           |
         +----+|                           |
HPD -----+     +---------------------------+

So right when power is applied there's a little bump in HPD and then
there's small spike right before it goes low.  The total time of the
little bump plus the spike was measured on one panel as being 8 ms
long.  The total time for the HPD to go high on the same panel was
51.2 ms, though the datasheet only promises it is < 200 ms.

When asked about this glitch, BOE indicated that it was expected and
persisted until the TCON has been initialized.

If this was a real hotpluggable DP panel then this wouldn't matter a
whole lot.  We'd debounce the HPD signal for a really long time and so
the little blip wouldn't hurt.  However, this is not a hotpluggable DP
panel and the the debouncing logic isn't needed and just shows down
the time needed to get the display working.  This is why the code in
panel_simple_prepare() doesn't do debouncing and just waits for HPD to
go high once.  Unfortunately if we get unlucky and happen to poll the
HPD line right at the spike we can try talking to the panel before
it's ready.

Let's handle this situation by putting in a 15 ms prepare delay and
decreasing the "hpd absent delay" by 15 ms.  That means:
* If you don't have HPD hooked up at all you've still got the
  hardcoded 200 ms delay.
* If you've got HPD hooked up you will always wait at least 15 ms
  before checking HPD.  The only case where this could be bad is if
  the panel is sharing a voltage rail with something else in the
  system and was already turned on long before the panel came up.  In
  such a case we'll be delaying 15 ms for no reason, but it's not a
  huge delay and I don't see any other good solution to handle that
  case.

Even though the delay was measured as 8 ms, 15 ms was chosen to give a
bit of margin.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716132120.1.I01e738cd469b61fc9b28b3ef1c6541a4f48b11bf@changeid

After the drm_bridge_connector_init() helper function has been added,
the ADV driver has been changed accordingly. However, the 'type'
field of the bridge structure was left unset, which makes the helper
function always return -EINVAL.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org> # tested on DragonBoard 410c
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720124228.12552-1-laurentiu.palcu@oss.nxp.com

Fix double-free bug in the error path.

Fixes: 65290075 ("drm: of: Add drm_of_lvds_get_dual_link_pixel_order")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1595502654-40595-1-git-send-email-biju.das.jz@bp.renesas.com

PP bcast is marked as doing async reset after job is done.
When resume after suspend, each PP is reset individually,
so no need to reset in PP bcast resume. But I forgot to
clear the PP bcast async reset mark so call into async wait
before job run and gets timeout.

Closes: https://gitlab.freedesktop.org/lima/linux/-/issues/34
Fixes: 3446d7e9 ("drm/lima: add resume/suspend callback for each ip")
Reviewed-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200719073050.776962-1-yuq825@gmail.com

When the extra HPD polling in sun4i_hdmi was removed, the result of
HPD was accidentally inverted.

Fix this by inverting the check.

Fixes: bda8eaa6 ("drm: sun4i: hdmi: Remove extra HPD polling")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200711011030.21997-1-wens@kernel.org

There exists a sleep-while-atomic bug while accessing the dmabuf->name
under mutex in the dmabuffs_dname(). This is caused from the SELinux
permissions checks on a process where it tries to validate the inherited
files from fork() by traversing them through iterate_fd() (which
traverse files under spin_lock) and call
match_file(security/selinux/hooks.c) where the permission checks happen.
This audit information is logged using dump_common_audit_data() where it
calls d_path() to get the file path name. If the file check happen on
the dmabuf's fd, then it ends up in ->dmabuffs_dname() and use mutex to
access dmabuf->name. The flow will be like below:
flush_unauthorized_files()
  iterate_fd()
    spin_lock() --> Start of the atomic section.
      match_file()
        file_has_perm()
          avc_has_perm()
            avc_audit()
              slow_avc_audit()
	        common_lsm_audit()
		  dump_common_audit_data()
		    audit_log_d_path()
		      d_path()
                        dmabuffs_dname()
                          mutex_lock()--> Sleep while atomic.

Call trace captured (on 4.19 kernels) is below:
___might_sleep+0x204/0x208
__might_sleep+0x50/0x88
__mutex_lock_common+0x5c/0x1068
__mutex_lock_common+0x5c/0x1068
mutex_lock_nested+0x40/0x50
dmabuffs_dname+0xa0/0x170
d_path+0x84/0x290
audit_log_d_path+0x74/0x130
common_lsm_audit+0x334/0x6e8
slow_avc_audit+0xb8/0xf8
avc_has_perm+0x154/0x218
file_has_perm+0x70/0x180
match_file+0x60/0x78
iterate_fd+0x128/0x168
selinux_bprm_committing_creds+0x178/0x248
security_bprm_committing_creds+0x30/0x48
install_exec_creds+0x1c/0x68
load_elf_binary+0x3a4/0x14e0
search_binary_handler+0xb0/0x1e0

So, use spinlock to access dmabuf->name to avoid sleep-while-atomic.

Cc: <stable@vger.kernel.org> [5.3+]
Signed-off-by: Charan Teja Kalla <charante@codeaurora.org>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
 [sumits: added comment to spinlock_t definition to avoid warning]
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/a83e7f0d-4e54-9848-4b58-e1acdbe06735@codeaurora.org

The following backtrace is seen when running aspeed G5 kernels.

WARNING: CPU: 0 PID: 1 at drivers/gpu/drm/drm_fb_helper.c:2233 drm_fbdev_generic_setup+0x138/0x198
aspeed_gfx 1e6e6000.display: Device has not been registered.
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.8.0-rc3 #1
Hardware name: Generic DT based system
Backtrace:
[<8010d6d0>] (dump_backtrace) from [<8010d9b8>] (show_stack+0x20/0x24)
r7:00000009 r6:60000153 r5:00000000 r4:8119fa94
[<8010d998>] (show_stack) from [<80b8cb98>] (dump_stack+0xcc/0xec)
[<80b8cacc>] (dump_stack) from [<80123ef0>] (__warn+0xd8/0xfc)
r7:00000009 r6:80e62ed0 r5:00000000 r4:974c3ccc
[<80123e18>] (__warn) from [<80123f98>] (warn_slowpath_fmt+0x84/0xc4)
r9:00000009 r8:806a0140 r7:000008b9 r6:80e62ed0 r5:80e631f8 r4:974c2000
[<80123f18>] (warn_slowpath_fmt) from [<806a0140>] (drm_fbdev_generic_setup+0x138/0x198)
r9:00000001 r8:9758fc10 r7:9758fc00 r6:00000000 r5:00000020 r4:9768a000
[<806a0008>] (drm_fbdev_generic_setup) from [<806d4558>] (aspeed_gfx_probe+0x204/0x32c)
r7:9758fc00 r6:00000000 r5:00000000 r4:9768a000
[<806d4354>] (aspeed_gfx_probe) from [<806dfca0>] (platform_drv_probe+0x58/0xa8)

Since commit 1aed9509 ("drm/fb-helper: Remove return value from
drm_fbdev_generic_setup()"), drm_fbdev_generic_setup() must be called
after drm_dev_register() to avoid the warning. Do that.

Fixes: 1aed9509 ("drm/fb-helper: Remove return value from drm_fbdev_generic_setup()")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701001002.74997-1-linux@roeck-us.net

The HiSilicon hibmc driver triggers a splat at boot time as below

[   14.137806] ------------[ cut here ]------------
[   14.142405] hibmc-drm 0000:0a:00.0: Device has not been registered.
[   14.148661] WARNING: CPU: 0 PID: 496 at drivers/gpu/drm/drm_fb_helper.c:2233 drm_fbdev_generic_setup+0x15c/0x1b8
[   14.158787] [...]
[   14.278307] Call trace:
[   14.280742]  drm_fbdev_generic_setup+0x15c/0x1b8
[   14.285337]  hibmc_pci_probe+0x354/0x418
[   14.289242]  local_pci_probe+0x44/0x98
[   14.292974]  work_for_cpu_fn+0x20/0x30
[   14.296708]  process_one_work+0x1c4/0x4e0
[   14.300698]  worker_thread+0x2c8/0x528
[   14.304431]  kthread+0x138/0x140
[   14.307646]  ret_from_fork+0x10/0x18
[   14.311205] ---[ end trace a2000ec2d838af4d ]---

This turned out to be due to the fbdev device hasn't been registered when
drm_fbdev_generic_setup() is invoked. Let's fix the splat by moving it down
after drm_dev_register() which will follow the "Display driver example"
documented by commit de99f060 ("drm/drv: DOC: Add driver example
code").
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200706144713.1123-1-yuzenghui@huawei.com

The burst length is configured in VIU_OSD1_FIFO_CTRL_STAT[31] and
VIU_OSD1_FIFO_CTRL_STAT[11:10]. The public S905D3 datasheet describes
this as:
- 0x0 = up to 24 per burst
- 0x1 = up to 32 per burst
- 0x2 = up to 48 per burst
- 0x3 = up to 64 per burst
- 0x4 = up to 96 per burst
- 0x5 = up to 128 per burst

The lower two bits map to VIU_OSD1_FIFO_CTRL_STAT[11:10] while the upper
bit maps to VIU_OSD1_FIFO_CTRL_STAT[31].

Replace meson_viu_osd_burst_length_reg() with pre-defined macros which
set these values. meson_viu_osd_burst_length_reg() always returned 0
(for the two used values: 32 and 64 at least) and thus incorrectly set
the burst size to 24.

Fixes: 147ae1cb ("drm: meson: viu: use proper macros instead of magic constants")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200620155752.21065-1-martin.blumenstingl@googlemail.com

The HPD sense mechanism in Allwinner's old HDMI encoder hardware is more
or less an input-only GPIO. Other GPIO-based HPD implementations
directly return the current state, instead of polling for a specific
state and returning the other if that times out.

Remove the I/O polling from sun4i_hdmi_connector_detect() and directly
return a known state based on the current reading. This also gets rid
of excessive CPU usage by kworker as reported on Stack Exchange [1] and
Armbian forums [2].

 [1] https://superuser.com/questions/1515001/debian-10-buster-on-cubietruck-with-bug-in-sun4i-drm-hdmi
 [2] https://forum.armbian.com/topic/14282-headless-systems-and-sun4i_drm_hdmi-a10a20/

Fixes: 9c568101 ("drm/sun4i: Add HDMI support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629060032.24134-1-wens@kernel.org

Charan Teja reported a 'use-after-free' in dmabuffs_dname [1], which
happens if the dma_buf_release() is called while the userspace is
accessing the dma_buf pseudo fs's dmabuffs_dname() in another process,
and dma_buf_release() releases the dmabuf object when the last reference
to the struct file goes away.

I discussed with Arnd Bergmann, and he suggested that rather than tying
the dma_buf_release() to the file_operations' release(), we can tie it to
the dentry_operations' d_release(), which will be called when the last ref
to the dentry is removed.

The path exercised by __fput() calls f_op->release() first, and then calls
dput, which eventually calls d_op->d_release().

In the 'normal' case, when no userspace access is happening via dma_buf
pseudo fs, there should be exactly one fd, file, dentry and inode, so
closing the fd will kill of everything right away.

In the presented case, the dentry's d_release() will be called only when
the dentry's last ref is released.

Therefore, lets move dma_buf_release() from fops->release() to
d_ops->d_release()

Many thanks to Arnd for his FS insights :)

[1]: https://lore.kernel.org/patchwork/patch/1238278/

Fixes: bb2bb903 ("dma-buf: add DMA_BUF_SET_NAME ioctls")
Reported-by: syzbot+3643a18836bce555bff6@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> [5.3+]
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Charan Teja Reddy <charante@codeaurora.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Tested-by: Charan Teja Reddy <charante@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200611114418.19852-1-sumit.semwal@linaro.org

In the past we had a pile of hacks to orchestrate access between fbdev
emulation and native kms clients. We've tried to streamline this, by
always preferring the kms side above fbdev calls when a drm master
exists, because drm master controls access to the display resources.

Unfortunately this breaks existing userspace, specifically Xorg. When
exiting Xorg first restores the console to text mode using the KDSET
ioctl on the vt. This does nothing, because a drm master is still
around. Then it drops the drm master status, which again does nothing,
because logind is keeping additional drm fd open to be able to
orchestrate vt switches. In the past this is the point where fbdev was
restored, as part of the ->lastclose hook on the drm side.

Now to fix this regression we don't want to go back to letting fbdev
restore things whenever it feels like, or to the pile of hacks we've
had before. Instead try and go with a minimal exception to make the
KDSET case work again, and nothing else.

This means that if userspace does a KDSET call when switching between
graphical compositors, there will be some flickering with fbcon
showing up for a bit. But a) that's not a regression and b) userspace
can fix it by improving the vt switching dance - logind should have
all the information it needs.

While pondering all this I'm also wondering wheter we should have a
SWITCH_MASTER ioctl to allow race-free master status handover. But
that's for another day.

v2: Somehow forgot to cc all the fbdev people.

v3: Fix typo Alex spotted.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=208179
Cc: shlomo@fastmail.com
Reported-and-Tested-by: shlomo@fastmail.com
Cc: Michel Dänzer <michel@daenzer.net>
Fixes: 64914da2 ("drm/fbdev-helper: don't force restores")
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.7+
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Qiujun Huang <hqjagain@gmail.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200624092910.3280448-1-daniel.vetter@ffwll.ch

The main DRM device is actually a virtual device so it doesn't have the
iommus property, which is instead on the DMA masters, in this case the
mixers.

Add a call to of_dma_configure with the mixers DT node but on the DRM
virtual device to configure it in the same way than the mixers.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/9a4daf438dd3f2fe07afb23688bfb793a0613d7d.1589378833.git-series.maxime@cerno.tech
(cherry picked from commit b718102d)
[Maxime: Applied to -fixes since it missed the merge window and display is
         broken without it]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The Acer S1003 has proper DMI strings for sys-vendor and product-name,
so we do not need to match by BIOS-date.

This means that the Acer S1003 can use the generic lcd800x1280_rightside_up
drm_dmi_panel_orientation_data struct which is also used by other quirks.
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200531093025.28050-2-hdegoede@redhat.com

Like the Asus T100HA the Asus T101HA also uses a panel which has been
mounted 90 degrees rotated, albeit in the opposite direction.
Add a quirk for this.
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200531093025.28050-1-hdegoede@redhat.com

Fix the recent regression.

Fixes: dbc7ece1 ("video: uvesafb: use true,false for bool variables")
Cc: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/81c9f140-d6fb-803a-18c8-04dae1007ab3@samsung.com

Add connector type for newhaven_nhd_43_480272ef_atxl, as
drm_panel_bridge_add() requires connector type to be set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609102809.753203-1-tomi.valkeinen@ti.com

The LogicPD Type28 display used by several Logic PD products has not
worked since v5.6.

The connector type for the LogicPD Type 28 display is missing and
drm_panel_bridge_add() requires connector type to be set.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 0d35408a ("drm/panel: simple: Add Logic PD Type 28 display support")
Cc: Adam Ford <aford173@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.6+
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200615131934.12440-1-aford173@gmail.com

Unable to handle kernel NULL pointer dereference at virtual address 00000918
pgd = (ptrval)
[00000918] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.7.0-15001-gfa384b50b96b-dirty #514
Hardware name: ST-Ericsson Ux5x0 platform (Device Tree Support)
PC is at mcde_display_enable+0x78/0x7c0
LR is at mcde_display_enable+0x78/0x7c0

Fix this by using to_mcde() as in other functions.

Fixes: fd7ee85c ("drm/mcde: Don't use drm_device->dev_private")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200613223027.4189309-2-linus.walleij@linaro.org

The following bug appeared in the MCDE driver/display
initialization during the recent merge window.

First the place we call drm_fbdev_generic_setup() in the
wrong place: this needs to be called AFTER calling
drm_dev_register() else we get this splat:

 ------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at ../drivers/gpu/drm/drm_fb_helper.c:2198 drm_fbdev_generic_setup+0x164/0x1a8
mcde a0350000.mcde: Device has not been registered.
Modules linked in:
Hardware name: ST-Ericsson Ux5x0 platform (Device Tree Support)
[<c010e704>] (unwind_backtrace) from [<c010a86c>] (show_stack+0x10/0x14)
[<c010a86c>] (show_stack) from [<c0414f38>] (dump_stack+0x9c/0xb0)
[<c0414f38>] (dump_stack) from [<c0121c8c>] (__warn+0xb8/0xd0)
[<c0121c8c>] (__warn) from [<c0121d18>] (warn_slowpath_fmt+0x74/0xb8)
[<c0121d18>] (warn_slowpath_fmt) from [<c04b154c>] (drm_fbdev_generic_setup+0x164/0x1a8)
[<c04b154c>] (drm_fbdev_generic_setup) from [<c04ed278>] (mcde_drm_bind+0xc4/0x160)
[<c04ed278>] (mcde_drm_bind) from [<c04f06b8>] (try_to_bring_up_master+0x15c/0x1a4)
(...)
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200613223027.4189309-1-linus.walleij@linaro.org

Beginning a new release cycles for what will become v5.8. Updating
drm-misc-fixes accordingly.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

ttm_bo_add_move_fence() invokes dma_fence_get(), which returns a
reference of the specified dma_fence object to "fence" with increased
refcnt.

When ttm_bo_add_move_fence() returns, local variable "fence" becomes
invalid, so the refcount should be decreased to keep refcount balanced.

The reference counting issue happens in one exception handling path of
ttm_bo_add_move_fence(). When no_wait_gpu flag is equals to true, the
function forgets to decrease the refcnt increased by dma_fence_get(),
causing a refcnt leak.

Fix this issue by calling dma_fence_put() when no_wait_gpu flag is
equals to true.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/370221/Signed-off-by: Christian König <christian.koenig@amd.com>

ttm_bo_vm_fault_reserved() invokes dma_fence_get(), which returns a
reference of the specified dma_fence object to "moving" with increased
refcnt.

When ttm_bo_vm_fault_reserved() returns, local variable "moving" becomes
invalid, so the refcount should be decreased to keep refcount balanced.

The reference counting issue happens in several exception handling paths
of ttm_bo_vm_fault_reserved(). When those error scenarios occur such as
"err" equals to -EBUSY, the function forgets to decrease the refcnt
increased by dma_fence_get(), causing a refcnt leak.

Fix this issue by calling dma_fence_put() when no_wait_gpu flag is
equals to true.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/370219/Signed-off-by: Christian König <christian.koenig@amd.com>

Pull SafeSetID update from Micah Morton:
 "Add additional LSM hooks for SafeSetID

  SafeSetID is capable of making allow/deny decisions for set*uid calls
  on a system, and we want to add similar functionality for set*gid
  calls.

  The work to do that is not yet complete, so probably won't make it in
  for v5.8, but we are looking to get this simple patch in for v5.8
  since we have it ready.

  We are planning on the rest of the work for extending the SafeSetID
  LSM being merged during the v5.9 merge window"

* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
  security: Add LSM hooks to set*gid syscalls

The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>

Pull btrfs updates from David Sterba:
 "This reverts the direct io port to iomap infrastructure of btrfs
  merged in the first pull request. We found problems in invalidate page
  that don't seem to be fixable as regressions or without changing iomap
  code that would not affect other filesystems.

  There are four reverts in total, but three of them are followup
  cleanups needed to revert a43a67a2 cleanly. The result is the
  buffer head based implementation of direct io.

  Reverts are not great, but under current circumstances I don't see
  better options"

* tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: switch to iomap_dio_rw() for dio"
  Revert "fs: remove dio_end_io()"
  Revert "btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK"
  Revert "btrfs: split btrfs_direct_IO to read and write part"

Pull networking fixes from David Miller:

 1) Fix cfg80211 deadlock, from Johannes Berg.

 2) RXRPC fails to send norigications, from David Howells.

 3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
    Geliang Tang.

 4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.

 5) The ucc_geth driver needs __netdev_watchdog_up exported, from
    Valentin Longchamp.

 6) Fix hashtable memory leak in dccp, from Wang Hai.

 7) Fix how nexthops are marked as FDB nexthops, from David Ahern.

 8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.

 9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.

10) Fix link speed reporting in iavf driver, from Brett Creeley.

11) When a channel is used for XSK and then reused again later for XSK,
    we forget to clear out the relevant data structures in mlx5 which
    causes all kinds of problems. Fix from Maxim Mikityanskiy.

12) Fix memory leak in genetlink, from Cong Wang.

13) Disallow sockmap attachments to UDP sockets, it simply won't work.
    From Lorenz Bauer.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
  net: ethernet: ti: ale: fix allmulti for nu type ale
  net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
  net: atm: Remove the error message according to the atomic context
  bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
  libbpf: Support pre-initializing .bss global variables
  tools/bpftool: Fix skeleton codegen
  bpf: Fix memlock accounting for sock_hash
  bpf: sockmap: Don't attach programs to UDP sockets
  bpf: tcp: Recv() should return 0 when the peer socket is closed
  ibmvnic: Flush existing work items before device removal
  genetlink: clean up family attributes allocations
  net: ipa: header pad field only valid for AP->modem endpoint
  net: ipa: program upper nibbles of sequencer type
  net: ipa: fix modem LAN RX endpoint id
  net: ipa: program metadata mask differently
  ionic: add pcie_print_link_status
  rxrpc: Fix race between incoming ACK parser and retransmitter
  net/mlx5: E-Switch, Fix some error pointer dereferences
  net/mlx5: Don't fail driver on failure to create debugfs
  net/mlx5e: CT: Fix ipv6 nat header rewrite actions
  ...

This reverts commit a43a67a2.

This patch reverts the main part of switching direct io implementation
to iomap infrastructure. There's a problem in invalidate page that
couldn't be solved as regression in this development cycle.

The problem occurs when buffered and direct io are mixed, and the ranges
overlap. Although this is not recommended, filesystems implement
measures or fallbacks to make it somehow work. In this case, fallback to
buffered IO would be an option for btrfs (this already happens when
direct io is done on compressed data), but the change would be needed in
the iomap code, bringing new semantics to other filesystems.

Another problem arises when again the buffered and direct ios are mixed,
invalidation fails, then -EIO is set on the mapping and fsync will fail,
though there's no real error.

There have been discussions how to fix that, but revert seems to be the
least intrusive option.

Link: https://lore.kernel.org/linux-btrfs/20200528192103.xm45qoxqmkw7i5yl@fiona/Signed-off-by: David Sterba <dsterba@suse.com>

On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.

This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f6447 ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").

Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().

Fixes: 9d1f6447 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2020-06-12

The following pull-request contains BPF updates for your *net* tree.

We've added 26 non-merge commits during the last 10 day(s) which contain
a total of 27 files changed, 348 insertions(+), 93 deletions(-).

The main changes are:

1) sock_hash accounting fix, from Andrey.

2) libbpf fix and probe_mem sanitizing, from Andrii.

3) sock_hash fixes, from Jakub.

4) devmap_val fix, from Jesper.

5) load_bytes_relative fix, from YiFei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Looking into the context (atomic!) and the error message should be dropped.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more cifs updates from Steve French:
 "12 cifs/smb3 fixes, 2 for stable.

   - add support for idsfromsid on create and chgrp/chown allowing
     ability to save owner information more naturally for some workloads

   - improve query info (getattr) when SMB3.1.1 posix extensions are
     negotiated by using new query info level"

* tag '5.8-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add debug message for new file creation with idsfromsid mount option
  cifs: fix chown and chgrp when idsfromsid mount option enabled
  smb3: allow uid and gid owners to be set on create with idsfromsid mount option
  smb311: Add tracepoints for new compound posix query info
  smb311: add support for using info level for posix extensions query
  smb311: Add support for lookup with posix extensions query info
  smb311: Add support for SMB311 query info (non-compounded)
  SMB311: Add support for query info using posix extensions (level 100)
  smb3: add indatalen that can be a non-zero value to calculation of credit charge in smb2 ioctl
  smb3: fix typo in mount options displayed in /proc/mounts
  cifs: Add get_security_type_str function to return sec type.
  smb3: extend fscache mount volume coherency check

Let's keep "git status" happy and quiet.

Fixes: 9762dc14 ("samples: add binderfs sample program
Fixes: fca5e949 ("samples: binderfs: really compile this sample and fix build issues")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm not convinced the script makes useful automaed help lines anyway,
but since we're trying to deprecate the use of "---help---" in Kconfig
files, let's fix the doc example code too.

See commit a7f7f624 ("treewide: replace '---help---' in Kconfig
files with 'help'")

Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more Kbuild updates from Masahiro Yamada:

 - fix build rules in binderfs sample

 - fix build errors when Kbuild recurses to the top Makefile

 - covert '---help---' in Kconfig to 'help'

* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  treewide: replace '---help---' in Kconfig files with 'help'
  kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
  samples: binderfs: really compile this sample and fix build issues

Pull more SCSI updates from James Bottomley:
 "This is the set of changes collected since just before the merge
  window opened. It's mostly minor fixes in drivers.

  The one non-driver set is the three optical disk (sr) changes where
  two are error path fixes and one is a helper conversion.

  The big driver change is the hpsa compat_alloc_userspace rework by Al
  so he can kill the remaining user. This has been tested and acked by
  the maintainer"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
  scsi: acornscsi: Fix an error handling path in acornscsi_probe()
  scsi: storvsc: Remove memset before memory freeing in storvsc_suspend()
  scsi: cxlflash: Remove an unnecessary NULL check
  scsi: ibmvscsi: Don't send host info in adapter info MAD after LPM
  scsi: sr: Fix sr_probe() missing deallocate of device minor
  scsi: sr: Fix sr_probe() missing mutex_destroy
  scsi: st: Convert convert get_user_pages() --> pin_user_pages()
  scsi: target: Rename target_setup_cmd_from_cdb() to target_cmd_parse_cdb()
  scsi: target: Fix NULL pointer dereference
  scsi: target: Initialize LUN in transport_init_se_cmd()
  scsi: target: Factor out a new helper, target_cmd_init_cdb()
  scsi: hpsa: hpsa_ioctl(): Tidy up a bit
  scsi: hpsa: Get rid of compat_alloc_user_space()
  scsi: hpsa: Don't bother with vmalloc for BIG_IOCTL_Command_struct
  scsi: hpsa: Lift {BIG_,}IOCTL_Command_struct copy{in,out} into hpsa_ioctl()
  scsi: ufs: Remove redundant urgent_bkop_lvl initialization
  scsi: ufs: Don't update urgent bkops level when toggling auto bkops
  scsi: qedf: Remove redundant initialization of variable rc
  scsi: mpt3sas: Fix memset() in non-RDPQ mode
  scsi: iscsi: Fix reference count leak in iscsi_boot_create_kobj
  ...