- 24 Sep, 2016 40 commits
-
-
Kweh, Hock Leong authored
commit 36afb176 upstream. According to IIO ABI definition, IIO_PRESSURE data output unit is kilopascal: http://lxr.free-electrons.com/source/Documentation/ABI/testing/sysfs-bus-iio This patch fix output unit of HID pressure sensor IIO driver from pascal to kilopascal to follow IIO ABI definition. Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Olof Johansson authored
commit 1c500840 upstream. In at least one known setup, the chip comes up in a state where reading the chip ID returns garbage unless it's been reset, due to noise on the wires during system boot. All supported chips have the same reset method, and based on the datasheets they all need 1.3 or 1.8ms to recover after reset. So, do the conservative thing here and always reset the chip. Signed-off-by: Olof Johansson <olof@lixom.net> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alison Schofield authored
commit 0d9dcf85 upstream. Replace the i2c_smbus_read_byte commmands used to retrieve the sensor data with an i2c_master_recv command. The smbus read byte method fails because the device does not expect a stop condition after sending the first byte. When we issue the second read, we are getting the first byte again. Net effect is that of the 14 bits used for the measurement, the 8 most significant bits are correct, the lower 6 are not. None of the smbus read protocols follow the pattern this device requires (S Addr Rd [A] Data [A] Data NA P), hence the switch to an i2c receive transaction. Applicable from original introduction of this driver, but will require backporting due to churn in the code. Signed-off-by: Alison Schofield <amsfield22@gmail.com> Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Anders Darander authored
commit c2ab4474 upstream. The driver always assumes that an input device has been created when reading channel 3. This causes a kernel panic when dereferencing st->ts_input. The change was introduced in commit 84882b06 ("iio: adc: at91_adc: Add support for touchscreens without TSMR"). Earlier versions only entered that part of the if-else statement if only the following flags are set: AT91_ADC_IER_XRDY | AT91_ADC_IER_YRDY | AT91_ADC_IER_PRDY Signed-off-by: Anders Darander <anders@chargestorm.se> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alison Schofield authored
commit 3c68858d upstream. Use the iio_pollfunc_store_time parameter during triggered buffer set-up to get valid timestamps. Signed-off-by: Alison Schofield <amsfield22@gmail.com> Cc: Daniel Baluta <daniel.baluta@gmail.com> Reviewed-By: Tiberiu Breana <tiberiu.a.breana@intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lars-Peter Clausen authored
commit 7d3cc21d upstream. The data buffer for captured mode for the ad799x driver is allocated in the update_scan_mode() callback. This callback is not set in the iio_info struct for the ad7791/ad7995/ad7999, which means that the data buffer is not allocated when a captured transfer is started. As a result the driver crashes when the first sample is received. To fix this properly set the update_scan_mode() callback. Fixes: d8dca330 ("staging:iio:ad799x: Preallocate sample buffer") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Giorgio Dal Molin authored
commit 522caebb upstream. The call to i2c_get_clientdata(client) returns a struct iio_dev*, not the needed struct ads1015_data*. We need here an intermediate step as in the function: void ads1015_get_channels_config(struct i2c_client *client). Signed-off-by: Giorgio Dal Molin <giorgio.nicole@arcor.de> Fixes: ecc24e72 ("iio: adc: Add TI ADS1015 ADC driver support") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vignesh R authored
commit 7175cce1 upstream. Now that open delay and sample delay for each channel is configurable via DT, the default IDLE_TIMEOUT value is not enough as this is calculated based on hardcoded macros. This results in driver returning EBUSY sometimes. Fix this by increasing the timeout value based on maximum value possible to open delay and sample delays for each channel. Fixes: 5dc11e81 ("iio: adc: ti_am335x_adc: make sample delay, open delay, averaging DT parameters") Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vignesh R authored
commit 90c43ec6 upstream. It is possible that two or more ADC channels can be simultaneously requested for raw samples, in which case there can be race in access to FIFO data resulting in loss of samples. If am335x_tsc_se_set_once() is called again from tiadc_read_raw(), when ADC is still acquired to sample one of the channels, the second process might be put into uninterruptible sleep state. Fix these issues, by protecting FIFO access and channel configurations with a mutex. Since tiadc_read_raw() might take anywhere between few microseconds to few milliseconds to finish execution (depending on averaging and delay values supplied via DT), its better to use mutex instead of spinlock. Fixes: 7ca6740c ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization") Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Caesar Wang authored
commit 543852af upstream. SARADC controller needs to be reset before programming it, otherwise it will not function properly. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-iio@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alison Schofield authored
commit f8adf645 upstream. Use the iio_pollfunc_store_time parameter during triggered buffer set-up to get valid timestamps. Signed-off-by: Alison Schofield <amsfield22@gmail.com> Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lars-Peter Clausen authored
commit b2f0c096 upstream. Use the IS_ENABLED() helper macro to ensure that the configfs group is initialized either when configfs is built-in or when configfs is built as a module. Otherwise software trigger creation will result in undefined behaviour when configfs is built as a mdoule since the configfs group for the trigger is not properly initialized. Fixes: b662f809 ("iio: core: Introduce IIO software triggers") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Daniel Baluta <daniel.baluta@intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Linus Walleij authored
commit 7ac61a06 upstream. Any readings from the raw interface of the KXSD9 driver will return an empty string, because it does not return IIO_VAL_INT but rather some random value from the accelerometer to the caller. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Paolo Bonzini authored
commit b0eaf450 upstream. When userspace sends KVM_SET_LAPIC, KVM schedules a check between the vCPU's IRR and ISR and the IOAPIC redirection table, in order to re-establish the IOAPIC's dest_map (the list of CPUs servicing the real-time clock interrupt with the corresponding vectors). However, __rtc_irq_eoi_tracking_restore_one was forgetting to set dest_map->vectors. Because of this, the IOAPIC did not process the real-time clock interrupt EOI, ioapic->rtc_status.pending_eoi got stuck at a non-zero value, and further RTC interrupts were reported to userspace as coalesced. Fixes: 9e4aabe2 Fixes: 4d99ba89 Cc: Joerg Roedel <jroedel@suse.de> Cc: David Gilbert <dgilbert@redhat.com> Reviewed-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Suzuki K Poulose authored
commit 293f2936 upstream. On arm/arm64, we depend on the kvm_unmap_hva* callbacks (via mmu_notifiers::invalidate_*) to unmap the stage2 pagetables when the userspace buffer gets unmapped. However, when the Hypervisor process exits without explicit unmap of the guest buffers, the only notifier we get is kvm_arch_flush_shadow_all() (via mmu_notifier::release ) which does nothing on arm. Later this causes us to access pages that were already released [via exit_mmap() -> unmap_vmas()] when we actually get to unmap the stage2 pagetable [via kvm_arch_destroy_vm() -> kvm_free_stage2_pgd()]. This triggers crashes with CONFIG_DEBUG_PAGEALLOC, which unmaps any free'd pages from the linear map. [ 757.644120] Unable to handle kernel paging request at virtual address ffff800661e00000 [ 757.652046] pgd = ffff20000b1a2000 [ 757.655471] [ffff800661e00000] *pgd=00000047fffe3003, *pud=00000047fcd8c003, *pmd=00000047fcc7c003, *pte=00e8004661e00712 [ 757.666492] Internal error: Oops: 96000147 [#3] PREEMPT SMP [ 757.672041] Modules linked in: [ 757.675100] CPU: 7 PID: 3630 Comm: qemu-system-aar Tainted: G D 4.8.0-rc1 #3 [ 757.683240] Hardware name: AppliedMicro X-Gene Mustang Board/X-Gene Mustang Board, BIOS 3.06.15 Aug 19 2016 [ 757.692938] task: ffff80069cdd3580 task.stack: ffff8006adb7c000 [ 757.698840] PC is at __flush_dcache_area+0x1c/0x40 [ 757.703613] LR is at kvm_flush_dcache_pmd+0x60/0x70 [ 757.708469] pc : [<ffff20000809dbdc>] lr : [<ffff2000080b4a70>] pstate: 20000145 ... [ 758.357249] [<ffff20000809dbdc>] __flush_dcache_area+0x1c/0x40 [ 758.363059] [<ffff2000080b6748>] unmap_stage2_range+0x458/0x5f0 [ 758.368954] [<ffff2000080b708c>] kvm_free_stage2_pgd+0x34/0x60 [ 758.374761] [<ffff2000080b2280>] kvm_arch_destroy_vm+0x20/0x68 [ 758.380570] [<ffff2000080aa330>] kvm_put_kvm+0x210/0x358 [ 758.385860] [<ffff2000080aa524>] kvm_vm_release+0x2c/0x40 [ 758.391239] [<ffff2000082ad234>] __fput+0x114/0x2e8 [ 758.396096] [<ffff2000082ad46c>] ____fput+0xc/0x18 [ 758.400869] [<ffff200008104658>] task_work_run+0x108/0x138 [ 758.406332] [<ffff2000080dc8ec>] do_exit+0x48c/0x10e8 [ 758.411363] [<ffff2000080dd5fc>] do_group_exit+0x6c/0x130 [ 758.416739] [<ffff2000080ed924>] get_signal+0x284/0xa18 [ 758.421943] [<ffff20000808a098>] do_signal+0x158/0x860 [ 758.427060] [<ffff20000808aad4>] do_notify_resume+0x6c/0x88 [ 758.432608] [<ffff200008083624>] work_pending+0x10/0x14 [ 758.437812] Code: 9ac32042 8b010001 d1000443 8a230000 (d50b7e20) This patch fixes the issue by moving the kvm_free_stage2_pgd() to kvm_arch_flush_shadow_all(). Tested-by: Itaru Kitayama <itaru.kitayama@riken.jp> Reported-by: Itaru Kitayama <itaru.kitayama@riken.jp> Reported-by: James Morse <james.morse@arm.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Hildenbrand authored
commit a7d4b8f2 upstream. As the meaning of these variables and pointers seems to change more frequently, let's directly access our save area, instead of going via current->thread. Right now, this is broken for set/get_fpu. They simply overwrite the host registers, as the pointers to the current save area were turned into the static host save area. Fixes: 3f6813b9 ("s390/fpu: allocate 'struct fpu' with the task_struct") Reported-by: Hao QingFeng <haoqf@linux.vnet.ibm.com> Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Emanuel Czirai authored
commit d1992996 upstream. AMD F12h machines have an erratum which can cause DIV/IDIV to behave unpredictably. The workaround is to set MSRC001_1029[31] but sometimes there is no BIOS update containing that workaround so let's do it ourselves unconditionally. It is simple enough. [ Borislav: Wrote commit message. ] Signed-off-by: Emanuel Czirai <icanrealizeum@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Yaowu Xu <yaowu@google.com> Link: http://lkml.kernel.org/r/20160902053550.18097-1-bp@alien8.deSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Steven Rostedt authored
commit 15301a57 upstream. Łukasz Daniluk reported that on a RHEL kernel that his machine would lock up after enabling function tracer. I asked him to bisect the functions within available_filter_functions, which he did and it came down to three: _paravirt_nop(), _paravirt_ident_32() and _paravirt_ident_64() It was found that this is only an issue when noreplace-paravirt is added to the kernel command line. This means that those functions are most likely called within critical sections of the funtion tracer, and must not be traced. In newer kenels _paravirt_nop() is defined within gcc asm(), and is no longer an issue. But both _paravirt_ident_{32,64}() causes the following splat when they are traced: mm/pgtable-generic.c:33: bad pmd ffff8800d2435150(0000000001d00054) mm/pgtable-generic.c:33: bad pmd ffff8800d3624190(0000000001d00070) mm/pgtable-generic.c:33: bad pmd ffff8800d36a5110(0000000001d00054) mm/pgtable-generic.c:33: bad pmd ffff880118eb1450(0000000001d00054) NMI watchdog: BUG: soft lockup - CPU#2 stuck for 22s! [systemd-journal:469] Modules linked in: e1000e CPU: 2 PID: 469 Comm: systemd-journal Not tainted 4.6.0-rc4-test+ #513 Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v02.05 05/07/2012 task: ffff880118f740c0 ti: ffff8800d4aec000 task.ti: ffff8800d4aec000 RIP: 0010:[<ffffffff81134148>] [<ffffffff81134148>] queued_spin_lock_slowpath+0x118/0x1a0 RSP: 0018:ffff8800d4aefb90 EFLAGS: 00000246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff88011eb16d40 RDX: ffffffff82485760 RSI: 000000001f288820 RDI: ffffea0000008030 RBP: ffff8800d4aefb90 R08: 00000000000c0000 R09: 0000000000000000 R10: ffffffff821c8e0e R11: 0000000000000000 R12: ffff880000200fb8 R13: 00007f7a4e3f7000 R14: ffffea000303f600 R15: ffff8800d4b562e0 FS: 00007f7a4e3d7840(0000) GS:ffff88011eb00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7a4e3f7000 CR3: 00000000d3e71000 CR4: 00000000001406e0 Call Trace: _raw_spin_lock+0x27/0x30 handle_pte_fault+0x13db/0x16b0 handle_mm_fault+0x312/0x670 __do_page_fault+0x1b1/0x4e0 do_page_fault+0x22/0x30 page_fault+0x28/0x30 __vfs_read+0x28/0xe0 vfs_read+0x86/0x130 SyS_read+0x46/0xa0 entry_SYSCALL_64_fastpath+0x1e/0xa8 Code: 12 48 c1 ea 0c 83 e8 01 83 e2 30 48 98 48 81 c2 40 6d 01 00 48 03 14 c5 80 6a 5d 82 48 89 0a 8b 41 08 85 c0 75 09 f3 90 8b 41 08 <85> c0 74 f7 4c 8b 09 4d 85 c9 74 08 41 0f 18 09 eb 02 f3 90 8b Reported-by: Łukasz Daniluk <lukasz.daniluk@intel.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dan Williams authored
commit 9049771f upstream. track_pfn_insert() in vmf_insert_pfn_pmd() is marking dax mappings as uncacheable rendering them impractical for application usage. DAX-pte mappings are cached and the goal of establishing DAX-pmd mappings is to attain more performance, not dramatically less (3 orders of magnitude). track_pfn_insert() relies on a previous call to reserve_memtype() to establish the expected page_cache_mode for the range. While memremap() arranges for reserve_memtype() to be called, devm_memremap_pages() does not. So, teach track_pfn_insert() and untrack_pfn() how to handle tracking without a vma, and arrange for devm_memremap_pages() to establish the write-back-cache reservation in the memtype tree. Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Toshi Kani <toshi.kani@hpe.com> Reported-by: Kai Zhang <kai.ka.zhang@oracle.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Easwar Hariharan authored
commit b5e71019 upstream. Active QSFP cables were reset only every alternate iteration of the channel tuning algorithm instead of every iteration due to incorrect reset of the flag that controlled QSFP reset, resulting in using stale QSFP status in the channel tuning algorithm. Fixes: 8ebd4cf1 ("Add active and optical cable support") Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jason Gunthorpe authored
commit d1e09f30 upstream. Fixes an oops that might happen if uverbs_close races with remove_one. Both contexts may run ib_uverbs_cleanup_ucontext, it depends on the flow. Currently, there is no protection for a case that remove_one didn't make the cleanup it runs to its end, the underlying ib_device was freed then uverbs_close will call ib_uverbs_cleanup_ucontext and OOPs. Above might happen if uverbs_close deleted the file from the list then remove_one didn't find it and runs to its end. Fixes to protect against that case by a new cleanup lock so that ib_uverbs_cleanup_ucontext will be called always before that remove_one is ended. Fixes: 35d4a0b6 ("IB/uverbs: Fix race between ib_uverbs_open and remove_one") Reported-by: Devesh Sharma <devesh.sharma@broadcom.com> Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mike Marciniszyn authored
commit c62fb260 upstream. The qp init function does a kzalloc() while holding the RCU lock that encounters the following warning with a debug kernel when a cat of the qp_stats is done: [ 231.723948] rcu_scheduler_active = 1, debug_locks = 0 [ 231.731939] 3 locks held by cat/11355: [ 231.736492] #0: (debugfs_srcu){......}, at: [<ffffffff813001a5>] debugfs_use_file_start+0x5/0x90 [ 231.746955] #1: (&p->lock){+.+.+.}, at: [<ffffffff81289a6c>] seq_read+0x4c/0x3c0 [ 231.755873] #2: (rcu_read_lock){......}, at: [<ffffffffa0a0c535>] _qp_stats_seq_start+0x5/0xd0 [hfi1] [ 231.766862] The init functions do an implicit next which requires the rcu read lock before the kzalloc(). Fix for both drivers is to change the scope of the init function to only do the allocation and the initialization of the just allocated iter. The implict next is moved back into the respective start functions to fix the issue. Signed-off-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mike Snitzer authored
commit 299f6230 upstream. v4.8-rc3 commit 99f3c90d ("dm flakey: error READ bios during the down_interval") overlooked the 'drop_writes' feature, which is meant to allow reads to be issued rather than errored, during the down_interval. Fixes: 99f3c90d ("dm flakey: error READ bios during the down_interval") Reported-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mateusz Guzik authored
commit 5efc2443 upstream. Prior to the change the function would blindly deference mm, exe_file and exe_file->f_inode, each of which could have been NULL or freed. Use get_task_exe_file to safely obtain stable exe_file. Signed-off-by: Mateusz Guzik <mguzik@redhat.com> Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mateusz Guzik authored
commit cd81a917 upstream. For more convenient access if one has a pointer to the task. As a minor nit take advantage of the fact that only task lock + rcu are needed to safely grab ->exe_file. This saves mm refcount dance. Use the helper in proc_exe_link. Signed-off-by: Mateusz Guzik <mguzik@redhat.com> Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexandre Bounine authored
commit b3006929 upstream. Fix incorrect condition to identify involvment of a address translation mechanism. This bug results in NULL pointer kernel crash dump in cases when mapping of inbound RapidIO address range is requested within existing aprture. Link: http://lkml.kernel.org/r/20160901173144.2983-1-alexandre.bounine@idt.comSigned-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com> Cc: Barry Wood <barry.wood@idt.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Christoph Hellwig authored
commit 9b4b3f6a upstream. irq already contains the interrupt number for the port, don't add the port index to it. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: d684a90d ("ahci: per-port msix support") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Rientjes authored
commit c11600e4 upstream. KASAN allocates memory from the page allocator as part of kmem_cache_free(), and that can reference current->mempolicy through any number of allocation functions. It needs to be NULL'd out before the final reference is dropped to prevent a use-after-free bug: BUG: KASAN: use-after-free in alloc_pages_current+0x363/0x370 at addr ffff88010b48102c CPU: 0 PID: 15425 Comm: trinity-c2 Not tainted 4.8.0-rc2+ #140 ... Call Trace: dump_stack kasan_object_err kasan_report_error __asan_report_load2_noabort alloc_pages_current <-- use after free depot_save_stack save_stack kasan_slab_free kmem_cache_free __mpol_put <-- free do_exit This patch sets current->mempolicy to NULL before dropping the final reference. Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1608301442180.63329@chino.kir.corp.google.com Fixes: cd11016e ("mm, kasan: stackdepot implementation. Enable stackdepot for SLAB") Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michal Hocko authored
commit 6b4e3181 upstream. There have been several reports about pre-mature OOM killer invocation in 4.7 kernel when order-2 allocation request (for the kernel stack) invoked OOM killer even during basic workloads (light IO or even kernel compile on some filesystems). In all reported cases the memory is fragmented and there are no order-2+ pages available. There is usually a large amount of slab memory (usually dentries/inodes) and further debugging has shown that there are way too many unmovable blocks which are skipped during the compaction. Multiple reporters have confirmed that the current linux-next which includes [1] and [2] helped and OOMs are not reproducible anymore. A simpler fix for the late rc and stable is to simply ignore the compaction feedback and retry as long as there is a reclaim progress and we are not getting OOM for order-0 pages. We already do that for CONFING_COMPACTION=n so let's reuse the same code when compaction is enabled as well. [1] http://lkml.kernel.org/r/20160810091226.6709-1-vbabka@suse.cz [2] http://lkml.kernel.org/r/f7a9ea9d-bb88-bfd6-e340-3a933559305a@suse.cz Fixes: 0a0337e0 ("mm, oom: rework oom detection") Link: http://lkml.kernel.org/r/20160823074339.GB23577@dhcp22.suse.czSigned-off-by: Michal Hocko <mhocko@suse.com> Tested-by: Olaf Hering <olaf@aepfle.de> Tested-by: Ralf-Peter Rohbeck <Ralf-Peter.Rohbeck@quantum.com> Cc: Markus Trippelsdorf <markus@trippelsdorf.de> Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com> Cc: Ralf-Peter Rohbeck <Ralf-Peter.Rohbeck@quantum.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Joonsoo Kim <js1304@gmail.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thiago Jung Bauermann authored
commit 070c43ee upstream. If kexec_apply_relocations fails, kexec_load_purgatory frees pi->sechdrs and pi->purgatory_buf. This is redundant, because in case of error kimage_file_prepare_segments calls kimage_file_post_load_cleanup, which will also free those buffers. This causes two warnings like the following, one for pi->sechdrs and the other for pi->purgatory_buf: kexec-bzImage64: Loading purgatory failed ------------[ cut here ]------------ WARNING: CPU: 1 PID: 2119 at mm/vmalloc.c:1490 __vunmap+0xc1/0xd0 Trying to vfree() nonexistent vm area (ffffc90000e91000) Modules linked in: CPU: 1 PID: 2119 Comm: kexec Not tainted 4.8.0-rc3+ #5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: dump_stack+0x4d/0x65 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 ? find_vmap_area+0x19/0x70 ? kimage_file_post_load_cleanup+0x47/0xb0 __vunmap+0xc1/0xd0 vfree+0x2e/0x70 kimage_file_post_load_cleanup+0x5e/0xb0 SyS_kexec_file_load+0x448/0x680 ? putname+0x54/0x60 ? do_sys_open+0x190/0x1f0 entry_SYSCALL_64_fastpath+0x13/0x8f ---[ end trace 158bb74f5950ca2b ]--- Fix by setting pi->sechdrs an pi->purgatory_buf to NULL, since vfree won't try to free a NULL pointer. Link: http://lkml.kernel.org/r/1472083546-23683-1-git-send-email-bauerman@linux.vnet.ibm.comSigned-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Dave Young <dyoung@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Trond Myklebust authored
commit b519d408 upstream. Ensure that we conform to the algorithm described in RFC5661, section 18.36.4 for when to bump the sequence id. In essence we do it for all cases except when the RPC call timed out, or in case of the server returning NFS4ERR_DELAY or NFS4ERR_STALE_CLIENTID. Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Trond Myklebust authored
commit bf0291dd upstream. According to RFC5661, the client is responsible for serialising LAYOUTGET and LAYOUTRETURN to avoid ambiguity. Consider the case where we send both in parallel. Client Server ====== ====== LAYOUTGET(seqid=X) LAYOUTRETURN(seqid=X) LAYOUTGET return seqid=X+1 LAYOUTRETURN return seqid=X+2 Process LAYOUTRETURN Forget layout stateid Process LAYOUTGET Set seqid=X+1 The client processes the layoutget/layoutreturn in the wrong order, and since the result of the layoutreturn was to clear the only existing layout segment, the client forgets the layout stateid. When the LAYOUTGET comes in, it is treated as having a completely new stateid, and so the client sets the wrong sequence id... Fix is to check if there are outstanding LAYOUTGET requests before we send the LAYOUTRETURN (note that LAYOUGET will already wait if it sees an outstanding LAYOUTRETURN). Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Chuck Lever authored
commit 88584818 upstream. nfsd4_release_lockowner finds a lock owner that has no lock state, and drops cl_lock. Then release_lockowner picks up cl_lock and unhashes the lock owner. During the window where cl_lock is dropped, I don't see anything preventing a concurrent nfsd4_lock from finding that same lock owner and adding lock state to it. Move release_lockowner() into nfsd4_release_lockowner and hang onto the cl_lock until after the lock owner's state cannot be found again. Found by inspection, we don't currently have a reproducer. Fixes: 2c41beb0 ("nfsd: reduce cl_lock thrashing in ... ") Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Trond Myklebust authored
commit 98b0f80c upstream. On error, the callers expect us to return without bumping nn->cb_users[]. Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Trond Myklebust authored
commit e09c978a upstream. The slot table hasn't been an array since v3.7. Ensure that we use nfs4_lookup_slot() to access the slot correctly. Fixes: 87dda67e ("NFSv4.1: Allow SEQUENCE to resize the slot table...") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Trond Myklebust authored
commit b88fa69e upstream. Ensure that the client conforms to the normative behaviour described in RFC5661 Section 12.7.2: "If a client believes its lease has expired, it MUST NOT send I/O to the storage device until it has validated its lease." So ensure that we wait for the lease to be validated before using the layout. Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Trond Myklebust authored
commit 3dc14735 upstream. If the attempt to connect to a DS fails inside ff_layout_pg_init_read or ff_layout_pg_init_write, then we currently end up clearing the layout segment carried by the struct nfs_pageio_descriptor, causing an Oops when we later call into ff_layout_read_pagelist/ff_layout_write_pagelist. The fix is to ensure we return the layout and then retry. Fixes: 446ca219 ("pNFS/flexfiles: When initing reads or writes, we...") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Tejun Heo authored
commit df6a58c5 upstream. kernfs_notify_workfn() sends out file modified events for the scheduled kernfs_nodes. Because the modifications aren't from userland, it doesn't have the matching file struct at hand and can't use fsnotify_modify(). Instead, it looked up the inode and then used d_find_any_alias() to find the dentry and used fsnotify_parent() and fsnotify() directly to generate notifications. The assumption was that the relevant dentries would have been pinned if there are listeners, which isn't true as inotify doesn't pin dentries at all and watching the parent doesn't pin the child dentries even for dnotify. This led to, for example, inotify watchers not getting notifications if the system is under memory pressure and the matching dentries got reclaimed. It can also be triggered through /proc/sys/vm/drop_caches or a remount attempt which involves shrinking dcache. fsnotify_parent() only uses the dentry to access the parent inode, which kernfs can do easily. Update kernfs_notify_workfn() so that it uses fsnotify() directly for both the parent and target inodes without going through d_find_any_alias(). While at it, supply the target file name to fsnotify() from kernfs_node->name. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Evgeny Vereshchagin <evvers@ya.ru> Fixes: d911d987 ("kernfs: make kernfs_notify() trigger inotify events too") Cc: John McCutchan <john@johnmccutchan.com> Cc: Robert Love <rlove@rlove.org> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Gavin Shan authored
commit caa58f80 upstream. In pnv_ioda_free_pe(), the PE object (including the associated PE number) is cleared before resetting the corresponding bit in the PE allocation bitmap. It means PE#0 is always released to the bitmap wrongly. This fixes above issue by caching the PE number before the PE object is cleared. Fixes: 1e916772 ("powerpc/powernv: Use PE instead of number during setup and release" Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Paul Mackerras authored
commit f077aaf0 upstream. In commit c60ac569 ("powerpc: Update kernel VSID range", 2013-03-13) we lost a check on the region number (the top four bits of the effective address) for addresses below PAGE_OFFSET. That commit replaced a check that the top 18 bits were all zero with a check that bits 46 - 59 were zero (performed for all addresses, not just user addresses). This means that userspace can access an address like 0x1000_0xxx_xxxx_xxxx and we will insert a valid SLB entry for it. The VSID used will be the same as if the top 4 bits were 0, but the page size will be some random value obtained by indexing beyond the end of the mm_ctx_high_slices_psize array in the paca. If that page size is the same as would be used for region 0, then userspace just has an alias of the region 0 space. If the page size is different, then no HPTE will be found for the access, and the process will get a SIGSEGV (since hash_page_mm() will refuse to create a HPTE for the bogus address). The access beyond the end of the mm_ctx_high_slices_psize can be at most 5.5MB past the array, and so will be in RAM somewhere. Since the access is a load performed in real mode, it won't fault or crash the kernel. At most this bug could perhaps leak a little bit of information about blocks of 32 bytes of memory located at offsets of i * 512kB past the paca->mm_ctx_high_slices_psize array, for 1 <= i <= 11. Fixes: c60ac569 ("powerpc: Update kernel VSID range") Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-