- 11 May, 2012 14 commits
-
-
Linus Walleij authored
The MSP platform data callbacks use the old custom callbacks to set the state of the pins, switch over to using pinctrl. Cc: Ola Lilja <ola.o.lilja@stericsson.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
Alter the db8500_add_msp_i2s() calls to return a struct platform_device * pointer, not an integer. We nee the pointer to obtain a pinctrl handle. Cc: Ola Lilja <ola.o.lilja@stericsson.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
UART0 had a hack that enabled its pins on init and put it to sleep on the exit callback. Replace this with the pinctrl calls to do the same thing and update the runtime table with the two apropriate states for runtime/active and idle. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
At the beginning of the first patch series I included the custom ux500 pin control system to make sure I could eventually replace it with the standard subsystem driver. So now that we've done so, let's remove it. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
This converts the Ux500 family to use the pinctrl driver for configuring pins. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
There is an IDLE definition in the pinctrl framework, but for ux500 SLEEP is more apropriate. I've added some comments on the semantics of the common states so as to avoid misunderstandings. ChangeLog v1->v2: - Fixed terminology "on"->"into". Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
This implements the pin configuration interface for the Nomadik pin controller. As part of the exercise we add a bit in the pin_cfg_t for the Nomadik pinctrl driver that indicates if the pin should be forced into GPIO mode. This is not done to go behind the back of the GPIO subsystem, but to ensure that default modes can be set by hogs on boot and system suspend/resume states. It was used implicitly by the old code defining all config settings and modes in a single config word but we now have a split between pinmux and pinconf leading to the need to have this. We also add a bit for explicitly setting sleepmode of the pin. This was previously handled by custom calls with the _sleep() suffix, but we now have one single interface into the configuration so we replace this with a bit indicating that the pin shall be configured into sleep mode. Some of the configuration can be refactored later to use less custom fields on the pin_cfg_t but we are currently leaving the old function calls in place so we stay compatible. ChangeLog v1->v2: - Drop a hunk changing pinmuxing for GPIO and move it over to the preceding pinmux patch. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
Implements basic pinmux for the Nomadik pin controller. The plan is to split the existing singular pin config interface nmk_config_pin(), nmk_config_pins(), that will configure muxing and other settings at the same time, into two interfaces by splitting the code in pinmux and pinctrl and eventually deleting the old interface and its helper functions when all users are gone. nmk_gpio_set_mode() and nmk_gpio_get_mode() are two older interfaces for just configuring muxing/altfunctions that will also be replaced in the end. We take some extra care to handle the glitch-avoidance here, but it is simpler now since there is only one altsetting per pingroup so we know immediately if we need to avoid altfunc C glitches for a certain group. As part of the makeover implement the .request() and .free() calls on the GPIO chips and have them call back into the pinctrl layer to reserve GPIOs. ChangeLog v1->v2: - Rebased on pinctrl-mergebase-20120418 so we get the latest driver infrastructure where function count is done by a fixed value and we can drop a few range checks since this is now handled by the core. - Include a GPIO muxing hunk erroneously part of the pin config patch. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
Since all pins we can control are GPIOs, match a GPIO range to each pin in the debug function and call into the GPIO debug print function to have the per-pin information. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
Break out the code displaying the status of a single pin so we can use the same code in the pinctrl debug function. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
This adds a scratch pin control interface to the Nomadik pinctrl driver, and defines the pins and groups in the DB8500 ASIC. We define GPIO ranges to cover the pins exposed. The DB8500 has more pins than this but we restrict the driver to the pins that can be controlled from the combined GPIO and pin control hardware to begin with. ChangeLog v1->v2: - Base on the latest pinctrl development from pinctrl-mergebase-20120418 so we can get rid of legacy group count mechanism. Also drop the range checks for group index, this is handled by the core now. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Arnd Bergmann authored
a60b57ed "drivers/gpio: gpio-nomadik: Add support for irqdomains" broke building with CONFIG_OF_GPIO disabled. Without this patch, building nhk8815_defconfig results in: /home/arnd/linux-arm/drivers/gpio/gpio-nomadik.c: In function 'nmk_gpio_probe': /home/arnd/linux-arm/drivers/gpio/gpio-nomadik.c:1238:6: error: 'struct gpio_chip' has no member named 'of_node' make[3]: *** [drivers/gpio/gpio-nomadik.o] Error 1 make[2]: *** [drivers/gpio] Error 2 make[2]: *** Waiting for unfinished jobs.... make[1]: *** [drivers] Error 2 make[1]: *** Waiting for unfinished jobs.... make: *** [sub-make] Error 2 Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
I'm moving this driver over to the pinctrl subsystem to convert the custom pin mux/config scheme over to use pinctrl. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
Conflicts: drivers/pinctrl/core.c
-
- 24 Apr, 2012 8 commits
-
-
Ola Lilja authored
Create devices for the MSP-blocks (MSP0, MSP1, MSP2 and MSP3) and associate it with the correct clocks in the clock-framework. Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Lee Jones authored
Add irq domain support to the gpio-nomadik GPIO driver. This enables its users to support dynamic IRQ assignment, which is requried by Device Tree. Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Lee Jones authored
This creates Device Tree bindings for the Nomadik GPIO driver. Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
This updates the Ux500 pin handling to take much more care when applying pin settings for different platforms and peripherals. This is an accumulation of a longer history of updates to the MOP500 family pin file. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Rabin Vincent authored
Implement an API to allow a list of pincfgs to be remuxed to active and sleep modes, for power saving. This is not exported on purpose, because it is not to be called by drivers directly. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
The default configuration for a number of I2C and keypad pins was to pull-up. However on most reference designs the electronics already contain external pull-ups which means the internal pull-ups will lower the common resistance and increase power consumption on these lines, and in some reference designs the keypad inputs are not used so this will just cause problems. So remove these pull-ups and add them on demand instead if needed. Signed-off-by: Magnus Templing <magnus.templing@stericsson.com> Signed-off-by: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
This adds a few sleep mode pin config macros for sleep mode for the Nomadik GPIO/pin controller. Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com> Signed-off-by: Rikard Olsson <rikard.p.olsson@stericsson.com> Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Linus Walleij authored
We were using a custom io_p2v() (physical-to-virtual) translation macro, but it's fully possible to just ioremap() this memory now, so skip use of static addresses altogether. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 23 Apr, 2012 4 commits
-
-
Rabin Vincent authored
Low EMI (Electro-Magnetic Interference) mode means lower slew rate on the signals. The Nomadik GPIO controller supports this so create an interface to enable it. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Rabin Vincent authored
If the pin is switching to altfunc, and there was an interrupt installed on it which has been lazy disabled, actually mask the interrupt to prevent spurious interrupts that would occur while the pin is under control of the peripheral. Only SKE does this. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Rabin Vincent authored
Cache two more registers in the GPIO controller. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Rabin Vincent authored
Setting GPIOs' SLPM value to 1 (WAKEUP_DISABLE) is seen to cause increased power consumption in sleep/deep-sleep. So remove the code which disables SLPM based on the wakeup settings and only ensure it is on as needed. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 21 Apr, 2012 14 commits
-
-
Linus Torvalds authored
-
Yong Zhang authored
Otherwise cpu_active_mask will not set, which lead to other issue. Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Signed-off-by: Konrad Eisele <konrad@gaisler.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull "ARM: SoC fixes" from Olof Johansson: * at91, ux500, imx, omap and bcmring: - at91 fixes for =m driver build issues, irqdomain fixes and config dependency fixes - ux500 kconfig dependency fixes and a smp wakeup bugfix - imx idle bugfix and build fix due to irq domain changes - omap uart pinmux fixes, softreset regression revert and misc fixes - bcmring build error regression fix * ux500 and imx had some small defconfig updates in this branch * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits) ARM: bcmring: fix UART declarations ARM: imx: Fix imx5 idle logic bug ARM: imx27-dt: Fix build due to removal of irq_domain_add_simple() ARM: imx_v4_v5_defconfig: Add support for CONFIG_REGULATOR_FIXED_VOLTAGE ARM: OMAP1: DMTIMER: fix broken timer clock source selection ARM: OMAP: serial: Fix the ocp smart idlemode handling bug ARM: OMAP2+: UART: Fix incorrect population of default uart pads ARM: OMAP: sram: fix BUG in dpll code for !PM case dmaengine: Kconfig: fix Atmel at_hdmac entry USB: gadget/at91_udc: add gpio_to_irq() function to vbus interrupt USB: ohci-at91: change annotations for probe/remove functions leds-atmel-pwm.c: Make pwmled_probe() __devinit ARM: at91: fix at91sam9261ek Ethernet dm9000 irq ARM: at91: fix rm9200ek flash size ARM: at91: remove empty at91_init_serial function ARM: at91: fix typo in at91_pmc_base assembly declaration ARM: at91: Export at91_matrix_base ARM: at91: Export at91_pmc_base ARM: at91: Export at91_ramc_base ARM: at91: Export at91_st_base ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmcLinus Torvalds authored
Pull MMC fixes from Chris Ball: - Build fix for omap_hsmmc with OF against 3.4-rc1. - Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3, which broke hotplug card detection when UNSAFE_RESUME is set. - Fix a race condition in omap_hsmmc with runtime PM. - Fix two libertas SDIO-powered-resume regressions. - Small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx. * tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: mmc: core: Do not pre-claim host in suspend mmc: dw_mmc: prevent NULL dereference for dma_ops mmc: unbreak sdhci-esdhc-imx on i.MX25 mmc: cd-gpio: Include header to pickup exported symbol prototypes mmc: sdhci: refine non-removable card checking for card detection mmc: dw_mmc: Fix switch from DMA to PIO mmc: remove MMC bus legacy suspend/resume method mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage mmc: omap_hsmmc: build fix for CONFIG_OF=y and CONFIG_MMC_OMAP_HS=m mmc: fixes for eMMC v4.5 sanitize operation mmc: fixes for eMMC v4.5 discard operation
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-mediaLinus Torvalds authored
Pull media fixes from Mauro Carvalho Chehab: - Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on Kaffeine (Fedora 16 Bugzilla #812895); - Fixes a mutex unlock at an error condition at drx-k; - Fix winbond-cir set mode; - mt9m032: Fix a compilation breakage with some random Kconfig; - mt9m032: fix two dead locks; - xc5000: don't require an special firmware (that won't be provided by the vendor) just because the xtal frequency is different; - V4L DocBook: fix some typos at multi-plane formats description. * 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: [media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware [media] V4L: mt9m032: fix compilation breakage [media] V4L: DocBook: Fix typos in the multi-plane formats description [media] V4L: mt9m032: fix two dead-locks [media] rc-core: set mode for winbond-cir [media] drxk: Does not unlock mutex if sanity check failed in scu_command() [media] dvb_frontend: Fix a regression when switching back to DVB-S
-
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6Linus Torvalds authored
Pull MFD fixes from Samuel Ortiz: "We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040 conversion to an i2c driver. The latter may not sound like a fix but the twl6040 MFD driver won't probe without it, triggering an OMAP4 audio regression." * tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: mfd: Fix modular builds of rc5t583 regulator support mfd: Fix asic3_gpio_to_irq ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue mfd: Convert twl6040 to i2c driver, and separate it from twl core mfd : Fix dbx500 compilation error
-
Al Viro authored
it's always current->mm Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
pfm_vm_munmap() is simply vm_munmap() and pfm_remove_smpl_mapping() always get current as the first argument. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
... since exit_mmap() is coming and it will munmap() everything anyway. In all other cases aio_free_ring() has ctx->mm == current->mm; moreover, all other callers of vm_munmap() have mm == current->mm, so this will allow us to get rid of mm argument of vm_munmap(). Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Ulf Hansson authored
Since SDIO drivers may want to do some SDIO operations in their suspend callback functions, we must not keep the host claimed when calling them. Daniel Drake reported that libertas_sdio encountered a deadlock in its suspend function. Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Tested-by: Daniel Drake <dsd@laptop.org> [stable@: please apply to 3.2-stable and 3.3-stable] Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
-
Jaehoon Chung authored
Now, dma_ops is assumed that use the IDMAC. But if dma_ops is assigned the pdata->dma_ops, we didn't ensure that callback function is defined. If the callback isn't defined, then we should run in PIO mode. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
-
Eric Bénard authored
This was broken by me in 37865fe9 ("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more extensive tests would have shown that read or write of data to the card were failing (even if the partition table was correctly read). Signed-off-by: Eric Bénard <eric@eukrea.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
-
H Hartley Sweeten authored
Include the linux/mmc/cd-gpio.h header to pickup the prototypes for the two exported symbols. This quiets the sparse warnings: warning: symbol 'mmc_cd_gpio_request' was not declared. Should it be static? warning: symbol 'mmc_cd_gpio_free' was not declared. Should it be static? Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Venkatraman S <svenkatr@ti.com> Signed-off-by: Chris Ball <cjb@laptop.org>
-
Daniel Drake authored
Commit c79396c1 ("mmc: sdhci: prevent card detection activity for non-removable cards") disables card detection where the cards are marked as non-removable. This makes sense, but the implementation detail of calling mmc_card_is_removable() causes some problems, because mmc_card_is_removable() is overloaded with CONFIG_MMC_UNSAFE_RESUME semantics. In the OLPC XO case, we need CONFIG_MMC_UNSAFE_RESUME because our root filesystem is stored on SD, but we also have external SD card slots where we want automatic card detection. Refine the check to only apply to hosts marked as MMC_CAP_NONREMOVABLE, which is defined to mean that the card is *really* nonremovable. This could be revisited in future if we find a way to improve CONFIG_MMC_UNSAFE_RESUME semantics. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Chuanxiao Dong <chuanxiao.dong@intel.com> [stable@: please apply to 3.3-stable] Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
-