- 17 Aug, 2015 10 commits
-
-
Mathias Nyman authored
commit 7895086a upstream. We need to check that a TRB is part of the current segment before calculating its DMA address. Previously a ring segment didn't use a full memory page, and every new ring segment got a new memory page, so the off by one error in checking the upper bound was never seen. Now that we use a full memory page, 256 TRBs (4096 bytes), the off by one didn't catch the case when a TRB was the first element of the next segment. This is triggered if the virtual memory pages for a ring segment are next to each in increasing order where the ring buffer wraps around and causes errors like: [ 106.398223] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 0 comp_code 1 [ 106.398230] xhci_hcd 0000:00:14.0: Looking for event-dma fffd3000 trb-start fffd4fd0 trb-end fffd5000 seg-start fffd4000 seg-end fffd4ff0 The trb-end address is one outside the end-seg address. Tested-by:
Arkadiusz Miśkiewicz <arekm@maven.pl> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Brian King authored
commit 3f1c0581 upstream. Fixes another signed / unsigned array indexing bug in the ipr driver. Currently, when hrrq_index wraps, it becomes a negative number. We do the modulo, but still have a negative number, so we end up indexing backwards in the array. Given where the hrrq array is located in memory, we probably won't actually reference memory we don't own, but nonetheless ipr is still looking at data within struct ipr_ioa_cfg and interpreting it as struct ipr_hrr_queue data, so bad things could certainly happen. Each ipr adapter has anywhere from 1 to 16 HRRQs. By default, we use 2 on new adapters. Let's take an example: Assume ioa_cfg->hrrq_index=0x7fffffffe and ioa_cfg->hrrq_num=4: The atomic_add_return will then return -1. We mod this with 3 and get -2, add one and get -1 for an array index. On adapters which support more than a single HRRQ, we dedicate HRRQ to adapter initialization and error interrupts so that we can optimize the other queues for fast path I/O. So all normal I/O uses HRRQ 1-15. So we want to spread the I/O requests across those HRRQs. With the default module parameter settings, this bug won't hit, only when someone sets the ipr.number_of_msix parameter to a value larger than 3 is when bad things start to happen. Tested-by:
Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by:
Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Brian King authored
commit bb7c5433 upstream. When ipr's internal driver trace was changed to an atomic, a signed/unsigned bug slipped in which results in us indexing backwards in our memory buffer writing on memory that does not belong to us. This patch fixes this by removing the modulo and instead just mask off the low bits. Tested-by:
-
Brian King authored
commit 36b8e180 upstream. Make sure we have the host lock held when calling scsi_report_bus_reset. Fixes a crash seen as the __devices list in the scsi host was changing as we were iterating through it. Reviewed-by:
-
Alex Deucher authored
commit 0a90a0cf upstream. Fixes a broken hsync start value uncovered by: abc0b144 (drm: Perform basic sanity checks on probed modes) The driver handled the bad hsync start elsewhere, but the above commit prevented it from getting added. bug: https://bugs.freedesktop.org/show_bug.cgi?id=91401Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Jan Kara authored
commit 8f2f3eb5 upstream. fsnotify_clear_marks_by_group_flags() can race with fsnotify_destroy_marks() so that when fsnotify_destroy_mark_locked() drops mark_mutex, a mark from the list iterated by fsnotify_clear_marks_by_group_flags() can be freed and thus the next entry pointer we have cached may become stale and we dereference free memory. Fix the problem by first moving marks to free to a special private list and then always free the first entry in the special list. This method is safe even when entries from the list can disappear once we drop the lock. Signed-off-by:
Jan Kara <jack@suse.com> Reported-by:
Ashish Sangwan <a.sangwan@samsung.com> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
David Daney authored
commit 46011e6e upstream. On MIPS the GLOBAL bit of the PTE must have the same value in any aligned pair of PTEs. These pairs of PTEs are referred to as "buddies". In a SMP system is is possible for two CPUs to be calling set_pte() on adjacent PTEs at the same time. There is a race between setting the PTE and a different CPU setting the GLOBAL bit in its buddy PTE. This race can be observed when multiple CPUs are executing vmap()/vfree() at the same time. Make setting the buddy PTE's GLOBAL bit an atomic operation to close the race condition. The case of CONFIG_64BIT_PHYS_ADDR && CONFIG_CPU_MIPS32 is *not* handled. Signed-off-by:
David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/10835/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Felix Fietkau authored
commit 1d62d737 upstream. p->thread.user_cpus_allowed is zero-initialized and is only filled on the first sched_setaffinity call. To avoid adding overhead in the task initialization codepath, simply OR the returned mask in sched_getaffinity with p->cpus_allowed. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/10740/Signed-off-by:
-
James Hogan authored
commit 106eccb4 upstream. On Malta, since commit a87ea88d ("MIPS: Malta: initialise the RTC at boot"), the RTC is reinitialised and forced into binary coded decimal (BCD) mode during init, even if the bootloader has already initialised it, and may even have already put it into binary mode (as YAMON does). This corrupts the current time, can result in the RTC seconds being an invalid BCD (e.g. 0x1a..0x1f) for up to 6 seconds, as well as confusing YAMON for a while after reset, enough for it to report timeouts when attempting to load from TFTP (it actually uses the RTC in that code). Therefore only initialise the RTC to the extent that is necessary so that Linux avoids interfering with the bootloader setup, while also allowing it to estimate the CPU frequency without hanging, without a bootloader necessarily having done anything with the RTC (for example when the kernel is loaded via EJTAG). The divider control is configured for a 32KHZ reference clock if necessary, and the SET bit of the RTC_CONTROL register is cleared if necessary without changing any other bits (this bit will be set when coming out of reset if the battery has been disconnected). Fixes: a87ea88d ("MIPS: Malta: initialise the RTC at boot") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Reviewed-by:
Paul Burton <paul.burton@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/10739/Signed-off-by:
-
Arnd Bergmann authored
commit dd94d355 upstream. Commit b713aa0b "ARM: fix asm/memory.h build error" broke some configurations on mach-realview with sparsemem enabled, which is missing a definition of PHYS_OFFSET: arch/arm/include/asm/memory.h:268:42: error: 'PHYS_OFFSET' undeclared (first use in this function) #define PHYS_PFN_OFFSET ((unsigned long)(PHYS_OFFSET >> PAGE_SHIFT)) arch/arm/include/asm/dma-mapping.h:104:9: note: in expansion of macro 'PHYS_PFN_OFFSET' return PHYS_PFN_OFFSET + dma_to_pfn(dev, *dev->dma_mask); An easy workaround is for realview to define PHYS_OFFSET itself, in the same way we define it for platforms that don't have a private __virt_to_phys function. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
- 10 Aug, 2015 30 commits
-
-
Greg Kroah-Hartman authored
-
Fupan Li authored
Commit 35d5134b ("x86/efi: Correct EFI boot stub use of code32_start") imported a bug, which will cause 32bit kernel boot failed using efi method. It should use the label's address instead of the value stored in the label to caculate the address of code32_start. Signed-off-by:
Fupan Li <fupan.li@windriver.com> Reviewed-by:
Matt Fleming <matt.fleming@intel.com>
-
Nicholas Bellinger authored
commit 007d038b upstream. This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where an explicit iser-target logout would result in ->tx_thread_active being incorrectly cleared by the logout post handler, and subsequent TX kthread leak: commit 88dcd2da Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, change iscsit_logout_post_handler_closesession() and iscsit_logout_post_handler_samecid() to only cmpxchg() on ->tx_thread_active for traditional iscsi/tcp connections. This is required because iscsi/tcp connections are invoking logout post handler logic directly from TX kthread context, while iser connections are invoking logout post handler logic from a seperate workqueue context. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 417c20a9 upstream. This patch fixes a use-after-free bug in iscsit_release_sessions_for_tpg() where se_portal_group->session_lock was incorrectly released/re-acquired while walking the active se_portal_group->tpg_sess_list. The can result in a NULL pointer dereference when iscsit_close_session() shutdown happens in the normal path asynchronously to this code, causing a bogus dereference of an already freed list entry to occur. To address this bug, walk the session list checking for the same state as before, but move entries to a local list to avoid dropping the lock while walking the active list. As before, signal using iscsi_session->session_restatement=1 for those list entries to be released locally by iscsit_free_session() code. Reported-by:
Sunilkumar Nadumuttlu <sjn@datera.io> Cc: Sunilkumar Nadumuttlu <sjn@datera.io> Signed-off-by:
-
Andy Shevchenko authored
commit 5c02a420 upstream. Since NULL is used as valid clock object on optional clocks we have to handle this case in avr32 implementation as well. Fixes: e1824dfe (net: macb: Adjust tx_clk when link speed changes) Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Hans-Christian Egtvedt <egtvedt@samfundet.no> Signed-off-by:
-
Marc-André Lureau authored
commit 7932c0bd upstream. While reviewing vhost log code, I found out that log_file is never set. Note: I haven't tested the change (QEMU doesn't use LOG_FD yet). Signed-off-by:
Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Wengang Wang authored
commit 4fabb594 upstream. Fixes: 3e0249f9 ("RDS/IB: add refcount tracking to struct rds_ib_device") There lacks a dropping on rds_ib_device.refcount in case rds_ib_alloc_fmr failed(mr pool running out). this lead to the refcount overflow. A complain in line 117(see following) is seen. From vmcore: s_ib_rdma_mr_pool_depleted is 2147485544 and rds_ibdev->refcount is -2147475448. That is the evidence the mr pool is used up. so rds_ib_alloc_fmr is very likely to return ERR_PTR(-EAGAIN). 115 void rds_ib_dev_put(struct rds_ib_device *rds_ibdev) 116 { 117 BUG_ON(atomic_read(&rds_ibdev->refcount) <= 0); 118 if (atomic_dec_and_test(&rds_ibdev->refcount)) 119 queue_work(rds_wq, &rds_ibdev->free_work); 120 } fix is to drop refcount when rds_ib_alloc_fmr failed. Signed-off-by:
Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by:
Haggai Eran <haggaie@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Dmitry Skorodumov authored
commit 7cc03e48 upstream. The efi_info structure stores low 32 bits of memory map in efi_memmap and high 32 bits in efi_memmap_hi. While constructing pointer in the setup_e820(), need to take into account all 64 bit of the pointer. It is because on 64bit machine the function efi_get_memory_map() may return full 64bit pointer and before the patch that pointer was truncated. The issue is triggered on Parallles virtual machine and fixed with this patch. Signed-off-by:
Dmitry Skorodumov <sdmitry@parallels.com> Cc: Denis V. Lunev <den@openvz.org> Signed-off-by:
-
Zhuang Jin Can authored
commit aca3a048 upstream. Port link change with port in resume state should not be reported to usbcore, as this is an internal state to be handled by xhci driver. Reporting PLC to usbcore may cause usbcore clearing PLC first and port change event irq won't be generated. Signed-off-by:
Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by:
-
Zhuang Jin Can authored
commit fac4271d upstream. When the link is just waken, it's in Resume state, and driver sets PLS to U0. This refers to Phase 1. Phase 2 refers to when the link has completed the transition from Resume state to U0. With the fix of xhci: report U3 when link is in resume state, it also exposes an issue that usb3 roothub and controller can suspend right after phase 1, and this causes a hard hang in controller. To fix the issue, we need to prevent usb3 bus suspend if any port is resuming in phase 1. [merge separate USB2 and USB3 port resume checking to one -Mathias] Signed-off-by:
-
Zhuang Jin Can authored
commit 243292a2 upstream. xhci_hub_report_usb3_link_state() returns pls as U0 when the link is in resume state, and this causes usb core to think the link is in U0 while actually it's in resume state. When usb core transfers control request on the link, it fails with TRB error as the link is not ready for transfer. To fix the issue, report U3 when the link is in resume state, thus usb core knows the link it's not ready for transfer. Signed-off-by:
-
Brian Campbell authored
commit 326124a0 upstream. When resetting a device the number of active TTs may need to be corrected by xhci_update_tt_active_eps, but the number of old active endpoints supplied to it was always zero, so the number of TTs and the bandwidth reserved for them was not updated, and could rise unnecessarily. This affected systems using Intel's Patherpoint chipset, which rely on software bandwidth checking. For example, a Lenovo X230 would lose the ability to use ports on the docking station after enough suspend/resume cycles because the bandwidth calculated would rise with every cycle when a suitable device is attached. The correct number of active endpoints is calculated in the same way as in xhci_reserve_bandwidth. Signed-off-by:
Brian Campbell <bacam@z273.org.uk> Signed-off-by:
-
Oliver Neukum authored
commit 5fb2c782 upstream. This device automatically switches itself to another mode (0x1405) unless the specific access pattern of Windows is followed in its initial mode. That makes a dirty unmount of the internal storage devices inevitable if they are mounted. So the card reader of such a device should be ignored, lest an unclean removal become inevitable. This replaces an earlier patch that ignored all LUNs of this device. That patch was overly broad. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Reviewed-by:
Lars Melin <larsm17@gmail.com> Signed-off-by:
-
Lior Amsalem authored
commit 945b4744 upstream. This commit adds the necessary quirk to make the Marvell 4140 SATA PMP work properly. This PMP doesn't like SRST on port number 4 (the host port) so this commit marks this port as not supporting SRST. Signed-off-by:
Lior Amsalem <alior@marvell.com> Reviewed-by:
Nadav Haklai <nadavh@marvell.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Tejun Heo authored
commit 5f6c2d2b upstream. When a blkcg configuration is targeted to a partition rather than a whole device, blkg_conf_prep fails with -EINVAL; unfortunately, it forgets to put the gendisk ref in that case. Fix it. Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Bernhard Bender authored
commit 96849170 upstream. This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30 touch screen. Due to a missing delay between the RESET and SET_RATE commands, the touch screen may become unresponsive during system startup or driver loading. According to the DMC documentation, a delay is needed after the RESET command to allow the chip to complete its internal initialization. As this delay is not guaranteed, we had a system where the touch screen occasionally did not send any touch data. There was no other indication of the problem. The patch fixes the problem by adding a 150ms delay between the RESET and SET_RATE commands. Suggested-by:
Jakob Mustafa <jakob.mustafa@bytecmed.com> Signed-off-by:
Bernhard Bender <bernhard.bender@bytecmed.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Chris Metcalf authored
commit 3f81d244 upstream. We were previously using free_bootmem() and just getting lucky that nothing too bad happened. Signed-off-by:
Chris Metcalf <cmetcalf@ezchip.com> Signed-off-by:
-
NeilBrown authored
commit 34cab6f4 upstream. When we get a read error from the last working device, we don't try to repair it, and don't fail the device. We simple report a read error to the caller. However the current test for 'is this the last working device' is wrong. When there is only one fully working device, it assumes that a non-faulty device is that device. However a spare which is rebuilding would be non-faulty but so not the only working device. So change the test from "!Faulty" to "In_sync". If ->degraded says there is only one fully working device and this device is in_sync, this must be the one. This bug has existed since we allowed read_balance to read from a recovering spare in v3.0 Reported-and-tested-by:
Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054 ("md/raid1: clean up read_balance.") Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Jingju Hou authored
commit 9cd76049 upstream. pdev->dev.platform_data is not initialized if match is true in function sdhci_pxav3_probe. Just local variable pdata is assigned the return value from function pxav3_get_mmc_pdata(). static int sdhci_pxav3_probe(struct platform_device *pdev) { struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; ... if (match) { ret = mmc_of_parse(host->mmc); if (ret) goto err_of_parse; sdhci_get_of_property(pdev); pdata = pxav3_get_mmc_pdata(dev); } ... } Signed-off-by:
Jingju Hou <houjingj@marvell.com> Fixes: b650352d("mmc: sdhci-pxa: Add device tree support") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Joakim Tjernlund authored
commit 8e91125f upstream. Support for 8BIT bus with was added some time ago to sdhci-esdhc but then missed to remove the 8BIT from the reserved bit mask which made 8BIT non functional. Fixes: 66b50a00 ("mmc: esdhc: Add support for 8-bit bus width and..") Signed-off-by:
Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by:
-
Tom Hughes authored
commit 4479004e upstream. If we don't do this, and we then fail to recreate the debugfs directory during a mode change, then we will fail later trying to add stations to this now bogus directory: BUG: unable to handle kernel NULL pointer dereference at 0000006c IP: [<c0a92202>] mutex_lock+0x12/0x30 Call Trace: [<c0678ab4>] start_creating+0x44/0xc0 [<c0679203>] debugfs_create_dir+0x13/0xf0 [<f8a938ae>] ieee80211_sta_debugfs_add+0x6e/0x490 [mac80211] Signed-off-by:
Tom Hughes <tom@compton.nu> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Seymour, Shane M authored
commit e7ac6c66 upstream. Two SLES11 SP3 servers encountered similar crashes simultaneously following some kind of SAN/tape target issue: ... qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-8009:3: DEVICE RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: DEVICE RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8009:3: TARGET RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: TARGET RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8012:3: BUS RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-802b:3: BUS RESET SUCCEEDED nexus=3:0:2. qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8018:3: ADAPTER RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-00af:3: Performing ISP error recovery - ha=ffff88bf04d18000. rport-3:0-0: blocked FC remote port time out: removing target and saving binding qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8017:3: ADAPTER RESET SUCCEEDED nexus=3:0:2. rport-2:0-0: blocked FC remote port time out: removing target and saving binding sg_rq_end_io: device detached BUG: unable to handle kernel NULL pointer dereference at 00000000000002a8 IP: [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 PGD 7e6586f067 PUD 7e5af06067 PMD 0 [1739975.390354] Oops: 0002 [#1] SMP CPU 0 ... Supported: No, Proprietary modules are loaded [1739975.390463] Pid: 27965, comm: ABCD Tainted: PF X 3.0.101-0.29-default #1 HP ProLiant DL580 Gen8 RIP: 0010:[<ffffffff8133b268>] [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP: 0018:ffff8839dc1e7c68 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff883f0592fc00 RCX: 0000000000000090 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000138 RBP: 0000000000000138 R08: 0000000000000010 R09: ffffffff81bd39d0 R10: 00000000000009c0 R11: ffffffff81025790 R12: 0000000000000001 R13: ffff883022212b80 R14: 0000000000000004 R15: ffff883022212b80 FS: 00007f8e54560720(0000) GS:ffff88407f800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00000000000002a8 CR3: 0000007e6ced6000 CR4: 00000000001407f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process ABCD (pid: 27965, threadinfo ffff8839dc1e6000, task ffff883592e0c640) Stack: ffff883f0592fc00 00000000fffffffa 0000000000000001 ffff883022212b80 ffff883eff772400 ffffffffa03fa309 0000000000000000 0000000000000000 ffffffffa04003a0 ffff883f063196c0 ffff887f0379a930 ffffffff8115ea1e Call Trace: [<ffffffffa03fa309>] st_open+0x129/0x240 [st] [<ffffffff8115ea1e>] chrdev_open+0x13e/0x200 [<ffffffff811588a8>] __dentry_open+0x198/0x310 [<ffffffff81167d74>] do_last+0x1f4/0x800 [<ffffffff81168fe9>] path_openat+0xd9/0x420 [<ffffffff8116946c>] do_filp_open+0x4c/0xc0 [<ffffffff8115a00f>] do_sys_open+0x17f/0x250 [<ffffffff81468d92>] system_call_fastpath+0x16/0x1b [<00007f8e4f617fd0>] 0x7f8e4f617fcf Code: eb d3 90 48 83 ec 28 40 f6 c6 04 48 89 6c 24 08 4c 89 74 24 20 48 89 fd 48 89 1c 24 4c 89 64 24 10 41 89 f6 4c 89 6c 24 18 74 11 <f0> ff 8f 70 01 00 00 0f 94 c0 45 31 ed 84 c0 74 2b 4c 8d a5 a0 RIP [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP <ffff8839dc1e7c68> CR2: 00000000000002a8 Analysis reveals the cause of the crash to be due to STp->device being NULL. The pointer was NULLed via scsi_tape_put(STp) when it calls scsi_tape_release(). In st_open() we jump to err_out after scsi_block_when_processing_errors() completes and returns the device as offline (sdev_state was SDEV_DEL): 1180 /* Open the device. Needs to take the BKL only because of incrementing the SCSI host 1181 module count. */ 1182 static int st_open(struct inode *inode, struct file *filp) 1183 { 1184 int i, retval = (-EIO); 1185 int resumed = 0; 1186 struct scsi_tape *STp; 1187 struct st_partstat *STps; 1188 int dev = TAPE_NR(inode); 1189 char *name; ... 1217 if (scsi_autopm_get_device(STp->device) < 0) { 1218 retval = -EIO; 1219 goto err_out; 1220 } 1221 resumed = 1; 1222 if (!scsi_block_when_processing_errors(STp->device)) { 1223 retval = (-ENXIO); 1224 goto err_out; 1225 } ... 1264 err_out: 1265 normalize_buffer(STp->buffer); 1266 spin_lock(&st_use_lock); 1267 STp->in_use = 0; 1268 spin_unlock(&st_use_lock); 1269 scsi_tape_put(STp); <-- STp->device = 0 after this 1270 if (resumed) 1271 scsi_autopm_put_device(STp->device); 1272 return retval; The ref count for the struct scsi_tape had already been reduced to 1 when the .remove method of the st module had been called. The kref_put() in scsi_tape_put() caused scsi_tape_release() to be called: 0266 static void scsi_tape_put(struct scsi_tape *STp) 0267 { 0268 struct scsi_device *sdev = STp->device; 0269 0270 mutex_lock(&st_ref_mutex); 0271 kref_put(&STp->kref, scsi_tape_release); <-- calls this 0272 scsi_device_put(sdev); 0273 mutex_unlock(&st_ref_mutex); 0274 } In scsi_tape_release() the struct scsi_device in the struct scsi_tape gets set to NULL: 4273 static void scsi_tape_release(struct kref *kref) 4274 { 4275 struct scsi_tape *tpnt = to_scsi_tape(kref); 4276 struct gendisk *disk = tpnt->disk; 4277 4278 tpnt->device = NULL; <<<---- where the dev is nulled 4279 4280 if (tpnt->buffer) { 4281 normalize_buffer(tpnt->buffer); 4282 kfree(tpnt->buffer->reserved_pages); 4283 kfree(tpnt->buffer); 4284 } 4285 4286 disk->private_data = NULL; 4287 put_disk(disk); 4288 kfree(tpnt); 4289 return; 4290 } Although the problem was reported on SLES11.3 the problem appears in linux-next as well. The crash is fixed by reordering the code so we no longer access the struct scsi_tape after the kref_put() is done on it in st_open(). Signed-off-by:
Shane Seymour <shane.seymour@hp.com> Signed-off-by:
Darren Lavender <darren.lavender@hp.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.com> Acked-by:
Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by:
-
Takashi Iwai authored
commit 649ccd08 upstream. MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this seems not working correctly, a fix for pin NID 0x15 is needed in addition. It's equivalent with the fixup for MacBook Air 1,1, so use this instead. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131Reported-and-tested-by:
Jeffery Miller <jefferym@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Yao-Wen Mao authored
commit 2d1cb7f6 upstream. Add the correct dB ranges of Bose Companion 5 and Drangonfly DAC 1.2. Signed-off-by:
Yao-Wen Mao <yaowen@google.com> Signed-off-by:
-
Dominic Sacré authored
commit 0689a86a upstream. The Steinberg MI2 and MI4 interfaces are compatible with the USB class audio spec, but the MIDI part of the devices is reported as a vendor specific interface. This patch adds entries to quirks-table.h to recognize the MIDI endpoints. Audio functionality was already working and is unaffected by this change. Signed-off-by:
Dominic Sacré <dominic.sacre@gmx.de> Signed-off-by:
Albert Huitsing <albert@huitsing.nl> Acked-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Thomas Gleixner authored
commit 75a06189 upstream. The resend mechanism happily calls the interrupt handler of interrupts which are marked IRQ_NESTED_THREAD from softirq context. This can result in crashes because the interrupt handler is not the proper way to invoke the device handlers. They must be invoked via handle_nested_irq. Prevent the resend even if the interrupt has no valid parent irq set. Its better to have a lost interrupt than a crashing machine. Reported-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Alexey Brodkin authored
commit f51e2f19 upstream. Currently instruction_pointer() returns pt_regs->ret and so return value is of type "long", which implicitly stands for "signed long". While that's perfectly fine when dealing with 32-bit values if return value of instruction_pointer() gets assigned to 64-bit variable sign extension may happen. And at least in one real use-case it happens already. In perf_prepare_sample() return value of perf_instruction_pointer() (which is an alias to instruction_pointer() in case of ARC) is assigned to (struct perf_sample_data)->ip (which type is "u64"). And what we see if instuction pointer points to user-space application that in case of ARC lays below 0x8000_0000 "ip" gets set properly with leading 32 zeros. But if instruction pointer points to kernel address space that starts from 0x8000_0000 then "ip" is set with 32 leadig "f"-s. I.e. id instruction_pointer() returns 0x8100_0000, "ip" will be assigned with 0xffff_ffff__8100_0000. Which is obviously wrong. In particular that issuse broke output of perf, because perf was unable to associate addresses like 0xffff_ffff__8100_0000 with anything from /proc/kallsyms. That's what we used to see: ----------->8---------- 6.27% ls [unknown] [k] 0xffffffff8046c5cc 2.96% ls libuClibc-0.9.34-git.so [.] memcpy 2.25% ls libuClibc-0.9.34-git.so [.] memset 1.66% ls [unknown] [k] 0xffffffff80666536 1.54% ls libuClibc-0.9.34-git.so [.] 0x000224d6 1.18% ls libuClibc-0.9.34-git.so [.] 0x00022472 ----------->8---------- With that change perf output looks much better now: ----------->8---------- 8.21% ls [kernel.kallsyms] [k] memset 3.52% ls libuClibc-0.9.34-git.so [.] memcpy 2.11% ls libuClibc-0.9.34-git.so [.] malloc 1.88% ls libuClibc-0.9.34-git.so [.] memset 1.64% ls [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore 1.41% ls [kernel.kallsyms] [k] __d_lookup_rcu ----------->8---------- Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Cc: arc-linux-dev@synopsys.com Cc: linux-kernel@vger.kernel.org Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Martin Schwidefsky authored
commit f9c87a6f upstream. If the kernel is compiled with gcc 5.1 and the XZ compression option the decompress_kernel function calls _sclp_print_early in 64-bit mode while the content of the upper register half of %r6 is non-zero. This causes a specification exception on the servc instruction in _sclp_servc. The _sclp_print_early function saves and restores the upper registers halves but it fails to clear them for the 31-bit code of the mini sclp driver. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Al Viro authored
commit 75a6f82a upstream. Normally opening a file, unlinking it and then closing will have the inode freed upon close() (provided that it's not otherwise busy and has no remaining links, of course). However, there's one case where that does *not* happen. Namely, if you open it by fhandle with cold dcache, then unlink() and close(). In normal case you get d_delete() in unlink(2) notice that dentry is busy and unhash it; on the final dput() it will be forcibly evicted from dcache, triggering iput() and inode removal. In this case, though, we end up with *two* dentries - disconnected (created by open-by-fhandle) and regular one (used by unlink()). The latter will have its reference to inode dropped just fine, but the former will not - it's considered hashed (it is on the ->s_anon list), so it will stay around until the memory pressure will finally do it in. As the result, we have the final iput() delayed indefinitely. It's trivial to reproduce - void flush_dcache(void) { system("mount -o remount,rw /"); } static char buf[20 * 1024 * 1024]; main() { int fd; union { struct file_handle f; char buf[MAX_HANDLE_SZ]; } x; int m; x.f.handle_bytes = sizeof(x); chdir("/root"); mkdir("foo", 0700); fd = open("foo/bar", O_CREAT | O_RDWR, 0600); close(fd); name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0); flush_dcache(); fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR); unlink("foo/bar"); write(fd, buf, sizeof(buf)); system("df ."); /* 20Mb eaten */ close(fd); system("df ."); /* should've freed those 20Mb */ flush_dcache(); system("df ."); /* should be the same as #2 */ } will spit out something like Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 303843 1131 100% / Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 303843 1131 100% / Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 283282 21692 93% / - inode gets freed only when dentry is finally evicted (here we trigger than by remount; normally it would've happened in response to memory pressure hell knows when). Acked-by:
J. Bruce Fields <bfields@fieldses.org> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Kirill A. Shutemov authored
commit 6b7339f4 upstream. Reading page fault handler code I've noticed that under right circumstances kernel would map anonymous pages into file mappings: if the VMA doesn't have vm_ops->fault() and the VMA wasn't fully populated on ->mmap(), kernel would handle page fault to not populated pte with do_anonymous_page(). Let's change page fault handler to use do_anonymous_page() only on anonymous VMA (->vm_ops == NULL) and make sure that the VMA is not shared. For file mappings without vm_ops->fault() or shred VMA without vm_ops, page fault on pte_none() entry would lead to SIGBUS. Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Willy Tarreau <w@1wt.eu> Cc: stable@vger.kernel.org Signed-off-by:
-
