As a side effect of the following commit, the active TX
serializer may get disabled which may result in distorted
audio output.

ASoC: davinci-mcasp: Add support for multichannel playback
(2952b27e)

For example, if a 4 channel I2S playback with two TX serializers
is activated. Later on, if a recording of 2 channels, with only 1 RX
serializer is started, which will also disable one of the TX
serializer because max_active_serializers is only calculated for
RX (recording) stream. This patch fixes this issue.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Many X86 devices using a BYT SoC + RT5640 codec are cheap devices with
generic DMI strings, causing snd_soc_set_dmi_name() to fail to set a
long_name, making it impossible for userspace to have a correct UCM
profile which only uses inputs / outputs which are actually hooked up
on the device.

Our quirks already specify which input the internal mic is connected to
and if a single (mono) speaker is used or if the device has stereo
speakers.

This commit sets a long_name based on the quirks so that userspace can
have UCM profiles doing the right thing based on the long_name.

Note that if we ever encounter the need for a special UCM profile for
some device we can add a quirk to set a specific long_name for the
device,
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Even with our recently tweaked defaults, quite a few bytcr_rt5640 devices
still need quirks to be fully functional. This commits adds quirks where
necessary for the 16 bytcr_rt5640 devices I have access to.

The quirks are added for the following reasons:

1) Devices with only one speaker need the mono quirk to avoid driving an
unused and potentially short-circuited output. 8 of my sample of 16 devs
are mono, 4 of these would work with the defaults if it were not for their
mono speaker.

2) Devices using a different input for the internal mic then the default,
this is the case for 6 of my sample of 16 devices.

3) BYTCR devices without an ACPI channel map, which do not work with the
default of SSP0-AIF2, this is the case for 2 of my sample of 16 devices.

4) Devices which need non-default jack-detect settings, this is the case
for 6 of my sample of 16 devices.

This commit add quirks for the following devices:

Acer Iconia Tab 8 W1-810
Chuwi Vi8
HP Pavilion X2 10-n000nd
HP Stream 7
I.T. Works TW891
Lamina I8270
MSI S100
Pipo W4
PoV-mobii-800w (v2.0)
PoV-mobii-800w (v2.1)
Toshiba Click Mini L9W-B
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use dmi_first_match() instead of dmi_check_system() + callbacks, this
avoid the need to initialize dmi_system_id.callback for each
byt_rt5640_quirk_table entry.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

As we add more quirks it is useful to have some sort of order in the
quirk list, sort it alphabetically.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Out of the 11 BYTCR devices which I have access to for testing, 6 use
JD1IN4P for jack-detect, 2 use JD1IN4P non-inverted and the other 3 use
JD2IN4N, the ones not using JD1IN4P are all also special in other ways and
need a DMI quirk regardless.

All 5 BYT (non CR) devices which I have access to use JD2IN4N.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently we've 2 places with BYTCR defaults: 1. The generic catch-all
DMI_SYS_VENDOR=="Insyde" DMI quirk which selects SSP0-AIF1 for generic
Insyde BYTCR tablets without the ACPI channel package; and 2. the
defaults in the if (is_bytcr) {} code block.

Currently these are not identical, both select IN3 as the internal mic
output, but the "Insyde" DMI quirk leaves out the DIFF_MIC quirk. The
DIFF_MIC quirk should be enabled by default, because enabling diff. input
helps a lot for devices with a differential mic, where as it is a nop on
devices with a normal mic.

This commit adds the DIFF_MIC quirk to the "Insyde" DMI quirk path, by
adding a new BYTCR_INPUT_DEFAULTS define and using that in both code paths
which set BYTCR defaults.

Having a single place where the BYTCR input defaults are defined also
allows defining jack-detect defaults in a single place in a follow-up
commit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Out of the 11 BYTCR devices which I have access to for testing,
7 use IN3 for the internal mic and only 1 uses IN1 for the internal mic,
the other 3 use DMIC1.

So IN3 clearly is a better default, using IN3 as default avoids the need
to add DMI quirks for some of these devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add code to support setting jack-detect parameters through quirks and
extend the existing DMI quirk table entries for the Asus T100TA and the
Dell Venue 8 Pro 5830 to enable jack detection.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This fixes the following 3 issues:

1) The sys_vendor match should be for "Dell Inc." not "DellInc.",
   without this fixed the quirk never gets applied
2) DMIC1 is used not DMIC2, this was not a problem sofar because for
   regular BYT boards (rather then BYTCR) we default to DMIC1 and because
   of 1. the quirk was not being applied
3) The Dell Venue 8 5830 Pro only has a single speaker
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use device-properties for setting up the dmic, based on the
BYT_RT5640_MAP() value, instead of using the codec specific
rt5640_dmic_enable() function for this.  This also removes the need
for the BYT_RT5640_DMIC_EN quirk, which was always set together with
a MAP() quirk of DMIC1_MAP or DMIC2_MAP.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: 9958e8afbcad ("ASoC: rt5663: Use the set_jack() instead of the export function")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The patch replaces the export function with the new API set_jack().
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The sdma-pcm does not need any information from omap-dma.h, it only needs
to include the omap-dmaengine.h - for the omap_dma_filter_fn, but that
might not be needed at all as OMAP1 was converted to dma_slave_map, but
I can not test OMAP1.

Add the linux/device.h include as well for devm_kzalloc()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

WARNING: modpost: missing MODULE_LICENSE() in sound/soc/omap/snd-soc-sdma.o
see include/linux/module.h for more information
WARNING: modpost: missing MODULE_LICENSE() in sound/soc/omap/snd-soc-sdma.o
see include/linux/module.h for more information

Add the missing MODULE_LICENSE.

This patch also going to solve:
snd_soc_sdma: Unknown symbol devm_kmalloc (err 0)
snd_soc_sdma: Unknown symbol omap_dma_filter_fn (err 0)
snd_soc_sdma: Unknown symbol snd_dmaengine_pcm_prepare_slave_config (err 0)
snd_soc_sdma: Unknown symbol devm_snd_dmaengine_pcm_register (err 0)
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix the compile error introduced by: "ASoC: Intel: bytcr_rt5640:
Configure PLL1 before using it".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Trivial fix to spelling mistake in dev_err message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

There are only one set of ops on the compressed stream so no need to
reassign the copy callback repeatedly, stop after copy is seen to be
necessary.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds some common helper functions like translating dsp error
to linux error codes and channel mappings etc.

These functions are used in all the following qdsp6 drivers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add DT bindings for ASM (Audio Stream Manager) DSP module.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add DT bindings for ADM (Audio Device Manager) DSP module.
This module implements mixer controls to setup the connections between
AFE ports and ASM streams.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add DT bindings for AFE (Audio Frontend) DSP module.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add DT bindings for Q6CORE DSP module.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds support to APR bus (Asynchronous Packet Router) driver.
APR driver is made as a bus driver so that the apr devices can added removed
more dynamically depending on the state of the services on the dsp.
APR is used for communication between application processor and QDSP to
use services on QDSP like Audio and others.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add dt bindings for Qualcomm APR (Asynchronous Packet Router)
bus driver. This bus is used for communicating with DSP which provides
audio and various other services to cpu.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Removed separate byte count variables for playback and capture.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Added byte count register offset variables to audio_substream_data
structure. Modified dma pointer callback.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Added dma configuration parameters to rtd structure.
Moved dma configuration parameters initialization to
hw_params callback.
Removed hard coding in prepare and trigger callbacks.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

I2S controller on EP93xx seems to have undocumented HW issue. According to
"EP93xx User’s Guide", controller can handle underflow and either transmit
last sample or zeroes in such case until FIFO is filled again. In reality
undeflow conditions seem to confuse internal state machine from time to
time and the whole stream gets shifted by one byte (as captured by logic
analyser on the I2S outputs). One could only hear noise instead of original
stream and this continues until the FIFO is disabled and enabled again.

Work this around by watching underflow interrupt and resetting I2S TX
channel + fill FIFO with zero samples until DMA catches up again. This is
a nasty workaround, but it works. Hence, Kconfig option to disable it in
case of problems.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to "EP93xx User’s Guide" it's called I2SINTR and has number 60.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The driver never supported more than 2 channels because of
ep93xx_i2s_dma_data[] supporting only 1 DMA channel in each
direction.
Stop enabling two unused I2S controller FIFOs, this will simplify
future interrupt support.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Lenovo Ideapad Mixx 320 has a digital mic connected to DMIC2
add a DMI based quirk pointing to the intel_braswell_platform_data
for devices with a mic on DMIC2.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Lenovo Ideapad Mixx 310 has a differential internal analog mic,
add platform-data for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

All DAI drivers are now using the new sdma-pcm platform driver. The
omap-pcm can be removed from the tree, but we need to keep the SND_OMAP_SOC
Kconfig option until the relevant defconfigs are updated to avoid
regression due to missing audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the new platform driver in case of sDMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Set the "realtek,in1-differential" or "realtek,in3-differential"
device-property when the BYT_RT5640_DIFF_MIC quirk is set instead of
directly poking the codec registers.

This also fixes the BYT_RT5640_DIFF_MIC quirk not working when
combined with BYT_RT5640_IN3_MAP.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When platform_clock_control() first selects PLL1 as sysclk the PLL_CTRL
registers have not been setup yet and we effectively have an invalid clock
configuration until byt_rt5640_aif1_hw_params() gets called.

Add a new byt_rt5640_prepare_and_enable_pll1() helper and use that from
both platform_clock_control() and byt_rt5640_aif1_hw_params() to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Enable button press detection for headsets by using the ovcd IRQ to get
notified of button presses.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add jack-detect support, loosely based on earlier work on this by:

Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Francisco mendez <francisco.mendez@intel.com>

Note getting the OVCD to work reliable was sort of finicky, so there are
quite a few comments on this to hopefully avoid people breaking it in the
future.

This (and the follow-up button press support) has been tested on the
following devices:

Acer Iconia Tab 8 W1-810
Asus T100CHI
Asus T100TA
Asus T200TA
Axxo WT1011
Chuwi Vi8
Dell Venue 8 Pro 5830
HP Pavilion X2 10-n000nd
HP Stream 7
I.T. Works TW891
Lamina I8270
MSI S100
Peaq C1010
Pipo W4
PoV MobiiTAB-P800W (v2.0)
Toshiba Click Mini L9W-B

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196377Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>