- 29 Jan, 2020 40 commits
-
-
Andre Przywara authored
[ Upstream commit 39a1a894 ] Older versions of the Juno *SoC* TRM [1] recommended that the UART clock source should be 7.2738 MHz, whereas the *system* TRM [2] stated a more correct value of 7.3728 MHz. Somehow the wrong value managed to end up in our DT. Doing a prime factorisation, a modulo divide by 115200 and trying to buy a 7.2738 MHz crystal at your favourite electronics dealer suggest that the old value was actually a typo. The actual UART clock is driven by a PLL, configured via a parameter in some board.txt file in the firmware, which reads 7.37 MHz (sic!). Fix this to correct the baud rate divisor calculation on the Juno board. [1] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0515b.b/DDI0515B_b_juno_arm_development_platform_soc_trm.pdf [2] http://infocenter.arm.com/help/topic/com.arm.doc.100113_0000_07_en/arm_versatile_express_juno_development_platform_(v2m_juno)_technical_reference_manual_100113_0000_07_en.pdf Fixes: 71f867ec ("arm64: Add Juno board device tree.") Signed-off-by:
Andre Przywara <andre.przywara@arm.com> Acked-by:
Liviu Dudau <liviu.dudau@arm.com> Signed-off-by:
Sudeep Holla <sudeep.holla@arm.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Sam Bobroff authored
[ Upstream commit 62d91dd2 ] The INTERRUPT_CNTL2 register expects a valid DMA address, but is currently set with a GPU MC address. This can cause problems on systems that detect the resulting DMA read from an invalid address (found on a Power8 guest). Instead, use the DMA address of the dummy page because it will always be safe. Fixes: d8f60cfc ("drm/radeon/kms: Add support for interrupts on r6xx/r7xx chips (v3)") Fixes: 25a857fb ("drm/radeon/kms: add support for interrupts on SI") Fixes: a59781bb ("drm/radeon: add support for interrupts on CIK (v5)") Signed-off-by:
Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Chuhong Yuan authored
[ Upstream commit 340049d4 ] When devm_kcalloc fails, it forgets to call edma_free_slot. Replace direct return with failure handler to fix it. Fixes: 1be5336b ("dmaengine: edma: New device tree binding") Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Link: https://lore.kernel.org/r/20191118073802.28424-1-hslester96@gmail.comSigned-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit b756ad92 ] KCSAN reported the following data-race [1] Adding a couple of READ_ONCE()/WRITE_ONCE() should silence it. Since the report hinted about multiple cpus using the history concurrently, I added a test avoiding writing on it if the victim slot already contains the desired value. [1] BUG: KCSAN: data-race in fanout_demux_rollover / fanout_demux_rollover read to 0xffff8880b01786cc of 4 bytes by task 18921 on cpu 1: fanout_flow_is_huge net/packet/af_packet.c:1303 [inline] fanout_demux_rollover+0x33e/0x3f0 net/packet/af_packet.c:1353 packet_rcv_fanout+0x34e/0x490 net/packet/af_packet.c:1453 deliver_skb net/core/dev.c:1888 [inline] dev_queue_xmit_nit+0x15b/0x540 net/core/dev.c:1958 xmit_one net/core/dev.c:3195 [inline] dev_hard_start_xmit+0x3f5/0x430 net/core/dev.c:3215 __dev_queue_xmit+0x14ab/0x1b40 net/core/dev.c:3792 dev_queue_xmit+0x21/0x30 net/core/dev.c:3825 neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530 neigh_output include/net/neighbour.h:511 [inline] ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116 __ip6_finish_output net/ipv6/ip6_output.c:142 [inline] __ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127 ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152 NF_HOOK_COND include/linux/netfilter.h:294 [inline] ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175 dst_output include/net/dst.h:436 [inline] ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179 ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795 udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173 udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471 inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576 sock_sendmsg_nosec net/socket.c:637 [inline] sock_sendmsg+0x9f/0xc0 net/socket.c:657 ___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311 __sys_sendmmsg+0x123/0x350 net/socket.c:2413 __do_sys_sendmmsg net/socket.c:2442 [inline] __se_sys_sendmmsg net/socket.c:2439 [inline] __x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 write to 0xffff8880b01786cc of 4 bytes by task 18922 on cpu 0: fanout_flow_is_huge net/packet/af_packet.c:1306 [inline] fanout_demux_rollover+0x3a4/0x3f0 net/packet/af_packet.c:1353 packet_rcv_fanout+0x34e/0x490 net/packet/af_packet.c:1453 deliver_skb net/core/dev.c:1888 [inline] dev_queue_xmit_nit+0x15b/0x540 net/core/dev.c:1958 xmit_one net/core/dev.c:3195 [inline] dev_hard_start_xmit+0x3f5/0x430 net/core/dev.c:3215 __dev_queue_xmit+0x14ab/0x1b40 net/core/dev.c:3792 dev_queue_xmit+0x21/0x30 net/core/dev.c:3825 neigh_direct_output+0x1f/0x30 net/core/neighbour.c:1530 neigh_output include/net/neighbour.h:511 [inline] ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116 __ip6_finish_output net/ipv6/ip6_output.c:142 [inline] __ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127 ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152 NF_HOOK_COND include/linux/netfilter.h:294 [inline] ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175 dst_output include/net/dst.h:436 [inline] ip6_local_out+0x74/0x90 net/ipv6/output_core.c:179 ip6_send_skb+0x53/0x110 net/ipv6/ip6_output.c:1795 udp_v6_send_skb.isra.0+0x3ec/0xa70 net/ipv6/udp.c:1173 udpv6_sendmsg+0x1906/0x1c20 net/ipv6/udp.c:1471 inet6_sendmsg+0x6d/0x90 net/ipv6/af_inet6.c:576 sock_sendmsg_nosec net/socket.c:637 [inline] sock_sendmsg+0x9f/0xc0 net/socket.c:657 ___sys_sendmsg+0x2b7/0x5d0 net/socket.c:2311 __sys_sendmmsg+0x123/0x350 net/socket.c:2413 __do_sys_sendmmsg net/socket.c:2442 [inline] __se_sys_sendmmsg net/socket.c:2439 [inline] __x64_sys_sendmmsg+0x64/0x80 net/socket.c:2439 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 18922 Comm: syz-executor.3 Not tainted 5.4.0-rc6+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Fixes: 3b3a5b0a ("packet: rollover huge flows before small flows") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 9d027e3a ] A difference of two unsigned long needs long storage. Fixes: c7fb64db ("[NETLINK]: Neighbour table configuration and statistics via rtnetlink") Signed-off-by:
-
Tiezhu Yang authored
[ Upstream commit dece3c2a ] When call function hwmon_device_register failed, use the actual return value instead of always -ENOMEM. Fixes: 64f09aa9 ("MIPS: Loongson-3: Add CPU Hwmon platform driver") Signed-off-by:
Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by:
Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Huacai Chen <chenhc@lemote.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Janusz Krzysztofik authored
[ Upstream commit 39034bb0 ] Commit da298c6d ("[media] v4l2: replace video op g_mbus_fmt by pad op get_fmt") converted a former ov6650_g_fmt() video operation callback to an ov6650_get_fmt() pad operation callback. However, the converted function disregards a format->which flag that pad operations should obey and always returns active frame format settings. That can be fixed by always responding to V4L2_SUBDEV_FORMAT_TRY with -EINVAL, or providing the response from a pad config argument, likely updated by a former user call to V4L2_SUBDEV_FORMAT_TRY .set_fmt(). Since implementation of the latter is trivial, go for it. Fixes: da298c6d ("[media] v4l2: replace video op g_mbus_fmt by pad op get_fmt") Signed-off-by:
Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Janusz Krzysztofik authored
[ Upstream commit 1c6a2b63 ] User arguments passed to .get/set_fmt() pad operation callbacks may contain unsupported values. The driver takes control over frame size and pixel code as well as colorspace and field attributes but has never cared for remainig format attributes, i.e., ycbcr_enc, quantization and xfer_func, introduced by commit 11ff030c ("[media] v4l2-mediabus: improve colorspace support"). Fix it. Set up a static v4l2_mbus_framefmt structure with attributes initialized to reasonable defaults and use it for updating content of user provided arguments. In case of V4L2_SUBDEV_FORMAT_ACTIVE, postpone frame size update, now performed from inside ov6650_s_fmt() helper, util the user argument is first updated in ov6650_set_fmt() with default frame format content. For V4L2_SUBDEV_FORMAT_TRY, don't copy all attributes to pad config, only those handled by the driver, then fill the response with the default frame format updated with resulting pad config format code and frame size. Fixes: 11ff030c ("[media] v4l2-mediabus: improve colorspace support") Signed-off-by:
-
Janusz Krzysztofik authored
[ Upstream commit 12500731 ] Since its initial submission, the driver selects V4L2_COLORSPACE_JPEG for supported formats other than V4L2_MBUS_FMT_SBGGR8_1X8. According to v4l2-compliance test program, V4L2_COLORSPACE_JPEG applies exclusively to V4L2_PIX_FMT_JPEG. Since the sensor does not support JPEG format, fix it to always select V4L2_COLORSPACE_SRGB. Fixes: 2f6e2404 ("[media] SoC Camera: add driver for OV6650 sensor") Signed-off-by:
-
Marc Dionne authored
[ Upstream commit b485275f ] By default s_maxbytes is set to MAX_NON_LFS, which limits the usable file size to 2GB, enforced by the vfs. Commit b9b1f8d5 ("AFS: write support fixes") added support for the 64-bit fetch and store server operations, but did not change this value. As a result, attempts to write past the 2G mark result in EFBIG errors: $ dd if=/dev/zero of=foo bs=1M count=1 seek=2048 dd: error writing 'foo': File too large Set s_maxbytes to MAX_LFS_FILESIZE. Fixes: b9b1f8d5 ("AFS: write support fixes") Signed-off-by:
Marc Dionne <marc.dionne@auristor.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Stefan Wahren authored
[ Upstream commit bc19c329 ] The reset counter is specific for every QCA700x chip. So move this into the private driver struct. Otherwise we get unpredictable reset behavior in setups with multiple QCA700x chips. Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by:
Stefan Wahren <stefan.wahren@in-tech.com> Signed-off-by:
Stefan Wahren <wahrenst@gmx.net> Signed-off-by:
-
Jakub Kicinski authored
[ Upstream commit e0ad032e ] If packet corruption failed we jump to finish_segs and return NET_XMIT_SUCCESS. Seeing success will make the parent qdisc increment its backlog, that's incorrect - we need to return NET_XMIT_DROP. Fixes: 6071bd1a ("netem: Segment GSO packets on enqueue") Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
Jakub Kicinski authored
[ Upstream commit a7fa12d1 ] To corrupt a GSO frame we first perform segmentation. We then proceed using the first segment instead of the full GSO skb and requeue the rest of the segments as separate packets. If there are any issues with processing the first segment we still want to process the rest, therefore we jump to the finish_segs label. Commit 177b8007 ("net: netem: fix backlog accounting for corrupted GSO frames") started using the pointer to the first segment in the "rest of segments processing", but as mentioned above the first segment may had already been freed at this point. Backlog corrections for parent qdiscs have to be adjusted. Fixes: 177b8007 ("net: netem: fix backlog accounting for corrupted GSO frames") Reported-by:
kbuild test robot <lkp@intel.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Reported-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Robin Gong authored
[ Upstream commit bd73dfab ] Illegal memory will be touch if SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3 (41) exceed the size of structure sdma_script_start_addrs(40), thus cause memory corrupt such as slob block header so that kernel trap into while() loop forever in slob_free(). Please refer to below code piece in imx-sdma.c: for (i = 0; i < sdma->script_number; i++) if (addr_arr[i] > 0) saddr_arr[i] = addr_arr[i]; /* memory corrupt here */ That issue was brought by commit a572460b ("dmaengine: imx-sdma: Add support for version 3 firmware") because SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3 (38->41 3 scripts added) not align with script number added in sdma_script_start_addrs(2 scripts). Fixes: a572460b ("dmaengine: imx-sdma: Add support for version 3 firmware") Cc: stable@vger.kernel Link: https://www.spinics.net/lists/arm-kernel/msg754895.htmlSigned-off-by:
Robin Gong <yibin.gong@nxp.com> Reported-by:
Jurgen Lambrecht <J.Lambrecht@TELEVIC.com> Link: https://lore.kernel.org/r/1569347584-3478-1-git-send-email-yibin.gong@nxp.com [vkoul: update the patch title] Signed-off-by:
-
Jeffrey Hugo authored
[ Upstream commit 78e31c42 ] On msm8998, vblank timeouts are observed because the DSI controller is not reset properly, which ends up stalling the MDP. This is because the reset logic is not correct per the hardware documentation. The documentation states that after asserting reset, software should wait some time (no indication of how long), or poll the status register until it returns 0 before deasserting reset. wmb() is insufficient for this purpose since it just ensures ordering, not timing between writes. Since asserting and deasserting reset occurs on the same register, ordering is already guaranteed by the architecture, making the wmb extraneous. Since we would define a timeout for polling the status register to avoid a possible infinite loop, lets just use a static delay of 20 ms, since 16.666 ms is the time available to process one frame at 60 fps. Fixes: a689554b ("drm/msm: Initial add DSI connector support") Cc: Hai Li <hali@codeaurora.org> Cc: Rob Clark <robdclark@gmail.com> Signed-off-by:
Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Reviewed-by:
Sean Paul <sean@poorly.run> [seanpaul renamed RESET_DELAY to DSI_RESET_TOGGLE_DELAY_MS] Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191011133939.16551-1-jeffrey.l.hugo@gmail.comSigned-off-by:
-
YueHaibing authored
[ Upstream commit 11c9a7d3 ] If tcf_register_action failed, mirred_device_notifier should be unregistered. Fixes: 3b87956e ("net sched: fix race in mirred device removal") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Antonio Borneo authored
[ Upstream commit 5da202c8 ] The field "name" in struct ptp_clock_info has a fixed size of 16 chars and is used as zero terminated string by clock_name_show() in drivers/ptp/ptp_sysfs.c The current initialization value requires 17 chars to fit also the null termination, and this causes overflow to the next bytes in the struct when the string is read as null terminated: hexdump -C /sys/class/ptp/ptp0/clock_name 00000000 73 74 6d 6d 61 63 5f 70 74 70 5f 63 6c 6f 63 6b |stmmac_ptp_clock| 00000010 a0 ac b9 03 0a |.....| where the extra 4 bytes (excluding the newline) after the string represent the integer 0x03b9aca0 = 62500000 assigned to the field "max_adj" that follows "name" in the same struct. There is no strict requirement for the "name" content and in the comment in ptp_clock_kernel.h it's reported it should just be 'A short "friendly name" to identify the clock'. Replace it with "stmmac ptp". Signed-off-by:
Antonio Borneo <antonio.borneo@st.com> Fixes: 92ba6888 ("stmmac: add the support for PTP hw clock driver") Signed-off-by:
-
Eric Biggers authored
[ Upstream commit 36453c85 ] If llc_conn_state_process() sees that llc_conn_service() put the skb on a list, it will drop one fewer references to it. This is wrong because the current behavior is that llc_conn_service() never consumes a reference to the skb. The code also makes the number of skb references being dropped conditional on which of ind_prim and cfm_prim are nonzero, yet neither of these affects how many references are *acquired*. So there is extra code that tries to fix this up by sometimes taking another reference. Remove the unnecessary/broken refcounting logic and instead just add an skb_get() before the only two places where an extra reference is actually consumed. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
Eric Biggers authored
[ Upstream commit fc8d5db1 ] All callers of llc_conn_state_process() except llc_build_and_send_pkt() (via llc_ui_sendmsg() -> llc_ui_send_data()) assume that it always consumes a reference to the skb. Fix this caller to do the same. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johannes Berg authored
[ Upstream commit 95697f99 ] We can process deauth frames and all, but we drop them very early in the RX path today - this could never have worked. Fixes: 2cc59e78 ("mac80211: reply to AUTH with DEAUTH if sta allocation fails in IBSS") Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/20191004123706.15768-2-luca@coelho.fiSigned-off-by:
-
Jose Abreu authored
[ Upstream commit 25683bab ] Some setups may not have all Unicast addresses filters available. Check the number of available filters before trying to setup it. Fixes: 477286b5 ("stmmac: add GMAC4 core support") Signed-off-by:
Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by:
-
Ard Biesheuvel authored
[ Upstream commit 3a8ecc93 ] Commit 7fd8930f "nvme: add a common helper to read Identify Controller data" has re-introduced an issue that we have attempted to work around in the past, in commit a310acd7 ("NVMe: use split lo_hi_{read,write}q"). The problem is that some PCIe NVMe controllers do not implement 64-bit outbound accesses correctly, which is why the commit above switched to using lo_hi_[read|write]q for all 64-bit BAR accesses occuring in the code. In the mean time, the NVMe subsystem has been refactored, and now calls into the PCIe support layer for NVMe via a .reg_read64() method, which fails to use lo_hi_readq(), and thus reintroduces the problem that the workaround above aimed to address. Given that, at the moment, .reg_read64() is only used to read the capability register [which is known to tolerate split reads], let's switch .reg_read64() to lo_hi_readq() as well. This fixes a boot issue on some ARM boxes with NVMe behind a Synopsys DesignWare PCIe host controller. Fixes: 7fd8930f ("nvme: add a common helper to read Identify Controller data") Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 23104218 ] The "gmac->phy_mode" variable is an enum and in this context GCC will treat it as an unsigned int so the error handling will never be triggered. Fixes: b1c17215 ("stmmac: add ipq806x glue layer") Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit d7eb6512 ] The "iface" variable is an enum and in this context GCC treats it as an unsigned int so the error handling is never triggered. Fixes: b7862412 ("of_mdio: Abstract a general interface for phy connect") Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit f1021051 ] The "dwmac->phy_mode" is an enum and in this context GCC treats it as an unsigned int so the error handling is never triggered. Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC") Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 25a58495 ] The "priv->phy_interface" variable is an enum and in this context GCC will treat it as unsigned so the error handling will never be triggered. Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 002dfe80 ] The "priv->phy_mode" variable is an enum and in this context GCC will treat it as unsigned to the error handling will never trigger. Fixes: 57c5bc9a ("net: hisilicon: add hix5hd2 mac driver") Signed-off-by:
-
Filippo Sironi authored
[ Upstream commit 0b15e02f ] To make sure the domain tlb flush completes before the function returns, explicitly wait for its completion. Signed-off-by:
Filippo Sironi <sironi@amazon.de> Fixes: 42a49f96 ("amd-iommu: flush domain tlb when attaching a new device") [joro: Added commit message and fixes tag] Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Gerd Rausch authored
[ Upstream commit 05a82481 ] All entries in 'rds_ib_stat_names' are stringified versions of the corresponding "struct rds_ib_statistics" element without the "s_"-prefix. Fix entry 'ib_evt_handler_call' to do the same. Fixes: f4f943c9 ("RDS: IB: ack more receive completions to improve performance") Signed-off-by:
Gerd Rausch <gerd.rausch@oracle.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
Mao Wenan authored
[ Upstream commit 49f6c90b ] sonic_send_packet will be processed in irq or non-irq context, so it would better use dev_kfree_skb_any instead of dev_kfree_skb. Fixes: d9fb9f38 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers") Signed-off-by:
Mao Wenan <maowenan@huawei.com> Signed-off-by:
-
Dan Robertson authored
[ Upstream commit fdc7d8e8 ] Fix an error in the bitmaskfor the shtc1 and shtw1 bitmask used to retrieve the chip ID from the ID register. See section 5.7 of the shtw1 or shtc1 datasheet for details. Fixes: 1a539d37 ("hwmon: add support for Sensirion SHTC1 sensor") Signed-off-by:
Dan Robertson <dan@dlrobertson.com> Link: https://lore.kernel.org/r/20190905014554.21658-3-dan@dlrobertson.com [groeck: Reordered to be first in series and adjusted accordingly] Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Filipe Manana authored
[ Upstream commit 7764d56b ] If we are able to load an existing inode cache off disk, we set the state of the cache to BTRFS_CACHE_FINISHED, but we don't wake up any one waiting for the cache to be available. This means that anyone waiting for the cache to be available, waiting on the condition that either its state is BTRFS_CACHE_FINISHED or its available free space is greather than zero, can hang forever. This could be observed running fstests with MOUNT_OPTIONS="-o inode_cache", in particular test case generic/161 triggered it very frequently for me, producing a trace like the following: [63795.739712] BTRFS info (device sdc): enabling inode map caching [63795.739714] BTRFS info (device sdc): disk space caching is enabled [63795.739716] BTRFS info (device sdc): has skinny extents [64036.653886] INFO: task btrfs-transacti:3917 blocked for more than 120 seconds. [64036.654079] Not tainted 5.2.0-rc4-btrfs-next-50 #1 [64036.654143] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [64036.654232] btrfs-transacti D 0 3917 2 0x80004000 [64036.654239] Call Trace: [64036.654258] ? __schedule+0x3ae/0x7b0 [64036.654271] schedule+0x3a/0xb0 [64036.654325] btrfs_commit_transaction+0x978/0xae0 [btrfs] [64036.654339] ? remove_wait_queue+0x60/0x60 [64036.654395] transaction_kthread+0x146/0x180 [btrfs] [64036.654450] ? btrfs_cleanup_transaction+0x620/0x620 [btrfs] [64036.654456] kthread+0x103/0x140 [64036.654464] ? kthread_create_worker_on_cpu+0x70/0x70 [64036.654476] ret_from_fork+0x3a/0x50 [64036.654504] INFO: task xfs_io:3919 blocked for more than 120 seconds. [64036.654568] Not tainted 5.2.0-rc4-btrfs-next-50 #1 [64036.654617] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [64036.654685] xfs_io D 0 3919 3633 0x00000000 [64036.654691] Call Trace: [64036.654703] ? __schedule+0x3ae/0x7b0 [64036.654716] schedule+0x3a/0xb0 [64036.654756] btrfs_find_free_ino+0xa9/0x120 [btrfs] [64036.654764] ? remove_wait_queue+0x60/0x60 [64036.654809] btrfs_create+0x72/0x1f0 [btrfs] [64036.654822] lookup_open+0x6bc/0x790 [64036.654849] path_openat+0x3bc/0xc00 [64036.654854] ? __lock_acquire+0x331/0x1cb0 [64036.654869] do_filp_open+0x99/0x110 [64036.654884] ? __alloc_fd+0xee/0x200 [64036.654895] ? do_raw_spin_unlock+0x49/0xc0 [64036.654909] ? do_sys_open+0x132/0x220 [64036.654913] do_sys_open+0x132/0x220 [64036.654926] do_syscall_64+0x60/0x1d0 [64036.654933] entry_SYSCALL_64_after_hwframe+0x49/0xbe Fix this by adding a wake_up() call right after setting the cache state to BTRFS_CACHE_FINISHED, at start_caching(), when we are able to load the cache from disk. Fixes: 82d5902d ("Btrfs: Support reading/writing on disk free ino cache") Reviewed-by:
Nikolay Borisov <nborisov@suse.com> Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Mao Wenan authored
[ Upstream commit 6e1cdedc ] NETDEV_TX_BUSY really should only be used by drivers that call netif_tx_stop_queue() at the wrong moment. If dma_map_single() is failed to map tx DMA buffer, it might trigger an infinite loop. This patch use NETDEV_TX_OK instead of NETDEV_TX_BUSY, and change printk to pr_err_ratelimited. Fixes: d9fb9f38 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers") Signed-off-by:
-
Lorenzo Bianconi authored
[ Upstream commit e1aa1a1d ] Fix following lockdep warning disabling bh in ath_dynack_node_init/ath_dynack_node_deinit [ 75.955878] -------------------------------- [ 75.955880] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. [ 75.955884] swapper/0/0 [HC0[0]:SC1[3]:HE1:SE0] takes: [ 75.955888] 00000000792a7ee0 (&(&da->qlock)->rlock){+.?.}, at: ath_dynack_sample_ack_ts+0x4d/0xa0 [ath9k_hw] [ 75.955905] {SOFTIRQ-ON-W} state was registered at: [ 75.955912] lock_acquire+0x9a/0x160 [ 75.955917] _raw_spin_lock+0x2c/0x70 [ 75.955927] ath_dynack_node_init+0x2a/0x60 [ath9k_hw] [ 75.955934] ath9k_sta_state+0xec/0x160 [ath9k] [ 75.955976] drv_sta_state+0xb2/0x740 [mac80211] [ 75.956008] sta_info_insert_finish+0x21a/0x420 [mac80211] [ 75.956039] sta_info_insert_rcu+0x12b/0x2c0 [mac80211] [ 75.956069] sta_info_insert+0x7/0x70 [mac80211] [ 75.956093] ieee80211_prep_connection+0x42e/0x730 [mac80211] [ 75.956120] ieee80211_mgd_auth.cold+0xb9/0x15c [mac80211] [ 75.956152] cfg80211_mlme_auth+0x143/0x350 [cfg80211] [ 75.956169] nl80211_authenticate+0x25e/0x2b0 [cfg80211] [ 75.956172] genl_family_rcv_msg+0x198/0x400 [ 75.956174] genl_rcv_msg+0x42/0x90 [ 75.956176] netlink_rcv_skb+0x35/0xf0 [ 75.956178] genl_rcv+0x1f/0x30 [ 75.956180] netlink_unicast+0x154/0x200 [ 75.956182] netlink_sendmsg+0x1bf/0x3d0 [ 75.956186] ___sys_sendmsg+0x2c2/0x2f0 [ 75.956187] __sys_sendmsg+0x44/0x80 [ 75.956190] do_syscall_64+0x55/0x1a0 [ 75.956192] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 75.956194] irq event stamp: 2357092 [ 75.956196] hardirqs last enabled at (2357092): [<ffffffff818c62de>] _raw_spin_unlock_irqrestore+0x3e/0x50 [ 75.956199] hardirqs last disabled at (2357091): [<ffffffff818c60b1>] _raw_spin_lock_irqsave+0x11/0x80 [ 75.956202] softirqs last enabled at (2357072): [<ffffffff8106dc09>] irq_enter+0x59/0x60 [ 75.956204] softirqs last disabled at (2357073): [<ffffffff8106dcbe>] irq_exit+0xae/0xc0 [ 75.956206] other info that might help us debug this: [ 75.956207] Possible unsafe locking scenario: [ 75.956208] CPU0 [ 75.956209] ---- [ 75.956210] lock(&(&da->qlock)->rlock); [ 75.956213] <Interrupt> [ 75.956214] lock(&(&da->qlock)->rlock); [ 75.956216] *** DEADLOCK *** [ 75.956217] 1 lock held by swapper/0/0: [ 75.956219] #0: 000000003bb5675c (&(&sc->sc_pcu_lock)->rlock){+.-.}, at: ath9k_tasklet+0x55/0x240 [ath9k] [ 75.956225] stack backtrace: [ 75.956228] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc1-wdn+ #13 [ 75.956229] Hardware name: Dell Inc. Studio XPS 1340/0K183D, BIOS A11 09/08/2009 [ 75.956231] Call Trace: [ 75.956233] <IRQ> [ 75.956236] dump_stack+0x67/0x90 [ 75.956239] mark_lock+0x4c1/0x640 [ 75.956242] ? check_usage_backwards+0x130/0x130 [ 75.956245] ? sched_clock_local+0x12/0x80 [ 75.956247] __lock_acquire+0x484/0x7a0 [ 75.956250] ? __lock_acquire+0x3b9/0x7a0 [ 75.956252] lock_acquire+0x9a/0x160 [ 75.956259] ? ath_dynack_sample_ack_ts+0x4d/0xa0 [ath9k_hw] [ 75.956262] _raw_spin_lock_bh+0x34/0x80 [ 75.956268] ? ath_dynack_sample_ack_ts+0x4d/0xa0 [ath9k_hw] [ 75.956275] ath_dynack_sample_ack_ts+0x4d/0xa0 [ath9k_hw] [ 75.956280] ath_rx_tasklet+0xd09/0xe90 [ath9k] [ 75.956286] ath9k_tasklet+0x102/0x240 [ath9k] [ 75.956288] tasklet_action_common.isra.0+0x6d/0x170 [ 75.956291] __do_softirq+0xcc/0x425 [ 75.956294] irq_exit+0xae/0xc0 [ 75.956296] do_IRQ+0x8a/0x110 [ 75.956298] common_interrupt+0xf/0xf [ 75.956300] </IRQ> [ 75.956303] RIP: 0010:cpuidle_enter_state+0xb2/0x400 [ 75.956308] RSP: 0018:ffffffff82203e70 EFLAGS: 00000202 ORIG_RAX: ffffffffffffffd7 [ 75.956310] RAX: ffffffff82219800 RBX: ffffffff822bd0a0 RCX: 0000000000000000 [ 75.956312] RDX: 0000000000000046 RSI: 0000000000000006 RDI: ffffffff82219800 [ 75.956314] RBP: ffff888155a01c00 R08: 00000011af51aabe R09: 0000000000000000 [ 75.956315] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000002 [ 75.956317] R13: 00000011af51aabe R14: 0000000000000003 R15: ffffffff82219800 [ 75.956321] cpuidle_enter+0x24/0x40 [ 75.956323] do_idle+0x1ac/0x220 [ 75.956326] cpu_startup_entry+0x14/0x20 [ 75.956329] start_kernel+0x482/0x489 [ 75.956332] secondary_startup_64+0xa4/0xb0 Fixes: c774d57f ("ath9k: add dynamic ACK timeout estimation") Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Tested-by:
Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit b1e18768 ] Currently the pointer val is being incorrectly incremented instead of the value pointed to by val. Fix this by adding in the missing * indirection operator. Addresses-Coverity: ("Unused value") Fixes: c03f2c53 ("staging:iio:dac: Add AD5380 driver") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Reviewed-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit 420c20be ] An earlier commit re-worked the setting of the bitmask and is now assigning v with some bit flags rather than bitwise or-ing them into v, consequently the earlier bit-settings of v are being lost. Fix this by replacing an assignment with the bitwise or instead. Addresses-Coverity: ("Unused value") Fixes: 2be25cac ("bcma: add constants for PCI and use them") Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 32910124 ] The problem is in gb_lights_request_handler(). If we get a request to change the config then we release the light with gb_lights_light_release() and re-allocated it. However, if the allocation fails part way through then we call gb_lights_light_release() again. This can lead to a couple different double frees where we haven't cleared out the original values: gb_lights_light_v4l2_unregister(light); ... kfree(light->channels); kfree(light->name); I also made a small change to how we set "light->channels_count = 0;". The original code handled this part fine and did not cause a use after free but it was sort of complicated to read. Fixes: 2870b52b ("greybus: lights: add lights implementation") Signed-off-by:
Rui Miguel Silva <rmfrfs@gmail.com> Link: https://lore.kernel.org/r/20190829122839.GA20116@mwandaSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Masami Hiramatsu authored
[ Upstream commit 7720804a ] Since x86 instruction decoder is not only for kprobes, it should be tested when the insn.c is compiled. (e.g. perf is enabled but kprobes is disabled) Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: cbe5c34c ("x86: Compile insn.c and inat.c only for KPROBES") Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Stephen Boyd authored
[ Upstream commit 82880222 ] We may want to use the device pointer in device_init_wakeup() with functions that expect the device to already be added with device_add(). For example, if we were to link the device initializing wakeup to something in sysfs such as a class for wakeups we'll run into an error. It looks like this code was written with the assumption that the device would be added before initializing wakeup due to the order of operations in power_supply_unregister(). Let's change the order of operations so we don't run into problems here. Fixes: 948dcf96 ("power_supply: Prevent suspend until power supply events are processed") Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Tri Vo <trong@android.com> Cc: Kalesh Singh <kaleshsingh@google.com> Cc: Ravi Chandra Sadineni <ravisadineni@chromium.org> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Stephen Boyd <swboyd@chromium.org> Acked-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by:
-
Guenter Roeck authored
[ Upstream commit 7d82fcc9 ] Writes into limit registers fail if the temperature written is negative. The regmap write operation checks the value range, regmap_write accepts an unsigned int as parameter, and the temperature value passed to regmap_write is kept in a variable declared as long. Negative values are converted large unsigned integers, which fails the range check. Fix by type casting the temperature to u16 when calling regmap_write(). Cc: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk> Fixes: e65365fe ("hwmon: (lm75) Convert to use regmap") Signed-off-by:
-
