During implementation of the new API bcm_qspi_bspi_set_flex_mode() has
been modified breaking calculation of address length. An unnecessary
multiplication was added breaking flash reads.

Fixes: 5f195ee7 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

We'd better have that documented in the kerneldoc header, so that it's
exposed to the doc generated by Sphinx.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add a description for spi_mem_op.data.nbytes to the kerneldoc header.

Fixes: c36ff266 ("spi: Extend the core to ease integration of SPI memory controllers")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When interrupted, wait_event_interruptible_timeout() returns
-ERESTARTSYS, and the SPI transfer in progress will fail, as expected:

    m25p80 spi0.0: SPI transfer failed: -512
    spi_master spi0: failed to transfer one message from queue

However, as the underlying DMA transfers may not have completed, all
subsequent SPI transfers may start to fail:

    spi_master spi0: receive timeout
    qspi_transfer_out_in() returned -110
    m25p80 spi0.0: SPI transfer failed: -110
    spi_master spi0: failed to transfer one message from queue

Fix this by calling dmaengine_terminate_all() not only for timeouts, but
also for errors.

This can be reproduced on r8a7991/koelsch, using "hd /dev/mtd0" followed
by CTRL-C.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

If the SPI queue is running during system suspend, the system may lock
up.

Fix this by stopping/restarting the queue during system suspend/resume,
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks.  In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.

Based on a patch for sh-msiof by Gaku Inami.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

This patch changes writing to the SISTR register according to the H/W
user's manual.

The TDREQ bit and RDREQ bits of SISTR are read-only, and must be written
their initial values of zero.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

If the SPI queue is running during system suspend, the system may lock
up.

Fix this by stopping/restarting the queue during system suspend/resume
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks.  In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Cleanup, reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

This fixes an embarrassing copy-and-paste error in the
errorpath of spi_gpio_request(): we were checking the wrong
struct member for error code right after retrieveing the
sck GPIO.

Fixes: 9b00bc7b ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Depending on the SPI instance one may get an interrupt storm upon
requesting resp. interrupt unless the clock is explicitly enabled
beforehand. This has been observed trying to bring up instance 4 on
T20.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

This patch fixes the dspi_eoq_write function used by the
ColdFire mcf5441x family. The 16 bit cmd part must be re-set at
each data transfer.

Also, now that fifo_size variables are used for eoq_read/write,
a proper fifo size must be set (16 slots for the ColdFire dspi
module version).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Acked-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

If the SPI bus number is provided by a DT alias, idr_alloc() is called
twice, leading to:

    WARNING: CPU: 1 PID: 1 at drivers/spi/spi.c:2179 spi_register_controller+0x11c/0x5d8
    couldn't get idr

Fix this by moving the handling of fixed SPI bus numbers up, before the
DT handling code fills in ctlr->bus_num.

Fixes: 1a4327fb ("spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

On systems where some controllers get a dynamic ID assigned and some have
a fixed number (e.g. from ACPI tables), the current implementation might
run into an IDR collision: in case of a fixed bus number is gotten by a
driver (but not marked busy in IDR tree) and a driver with dynamic bus
number gets the same ID and predictably fails.

Fix this by means of checking-in fixed IDsin IDR as far as dynamic ones
at the moment of the controller registration.

Fixes: 9b61e302 (spi: Pick spi bus number from Linux idr or spi alias)
Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

There is no reason to make spi_mem->name modifiable. Moreover,
spi_mem_ops->get_name() returns a const char *, which generates a gcc
warning when assigning the value returned by spi_mem_ops->get_name()
to spi_mem->name.

Fixes: 5d27a9c8 ("spi: spi-mem: Extend the SPI mem interface to set a custom memory name")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

By calling spi_mem_get_name(), the driver of the (Q)SPI controller can
set a custom name for the memory device if necessary.
This is useful to keep mtdparts compatible when controller drivers are
ported from the MTD to the SPI layer.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When porting (Q)SPI controller drivers from the MTD layer to the SPI
layer, the naming scheme for the memory devices changes. To be able
to keep compatibility with the old drivers naming scheme, a name
field is added to struct spi_mem and a hook is added to let controller
drivers set a custom name for the memory device.

Example for the FSL QSPI driver:

Name with the old driver: 21e0000.qspi,
or with multiple devices: 21e0000.qspi-0, 21e0000.qspi-1, ...

Name with the new driver without spi_mem_get_name: spi4.0
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix a typo in the @drvpriv description.
Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This commit removed include headers of linux/of.h and linux/of_platform.h,
because they are not used.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add SPI_3WIRE support to spi-gpio controller introducing
set_line_direction function pointer in spi_bitbang data structure.
Spi-gpio controller has been tested using hts221 temp/rh iio sensor
running in 3wire mode and lsm6dsm running in 4wire mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add the capability to specify the flag parameter used in
bitbang_txrx_be_cpha{0,1} through the txrx_word function pointers of
spi_bitbang data structure. That feature will be used to add spi-3wire
support to the spi-gpio controller
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add SPI controller driver implemented in Socionext UniPhier SoCs.

UniPhier SoCs have two types SPI controllers; SCSSI supports a
single channel, and MCSSI supports multiple channels.
This driver supports SCSSI only.

This controller has 32bit TX/RX FIFO with depth of eight entry,
and supports the SPI master mode only.

This commit is implemented in PIO transfer mode, not DMA transfer.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add DT bindings for SPI controller implemented in UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The integration of the Designware SPI controller on Microsemi SoCs requires
an extra register set to be able to give the IP control of the SPI
interface.

Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Even if the chip select line is not controlled by the SPFI
hardware, the device select bits need to be set to specify
the chip select line in use for the hardware to know what
parameters to use for the current transfer.
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Variable count, l, mcspi and spi_cntrl are being assigned but are
never used hence they are redundant and can be removed.

Cleans up clang warnings:
warning: variable 'count' set but not used [-Wunused-but-set-variable]
warning: variable 'l' set but not used [-Wunused-but-set-variable]
warning: variable 'mcspi' set but not used [-Wunused-but-set-variable]
warning: variable 'spi_cntrl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Because the SPI controller deasserts the chip select when the TX fifo is
empty (which may happen in the middle of a transfer), the CS should be
handled by linux. Unfortunately, some or all of the first four chip
selects are not muxable as GPIOs, depending on the SoC.

There is a way to bitbang those pins by using the SPI boot controller so
use it to set the chip selects.

At init time, it is also necessary to give control of the SPI interface to
the Designware IP.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Export dw_spi_set_cs so it can be used from the various IP integration
modules.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Log RX and TX fifo counters when a transfer is done and these are not
zero.
Signed-off-by: Tiago Brusamarello <tiago.brusamarello@datacom.ind.br>
Signed-off-by: Mark Brown <broonie@kernel.org>

Dynamic burst mode allows to group together multiple words and send them
in one continuous burst. When the number of bytes to be sent is not a
strict multiple of the FIFO entry size (32 bits), the controller expects
the non aligned bits to be sent first.

This commit adds support for this particular constraint, avoiding the
need to send the non-aligned bytes one by one at the end of the
transfer, speeding-up transfer speed in that case.

With this method, a transfer is divided into multiple bursts, limited in
size by the maximum amount of data that the controller can transfer in
one continuous burst (which is 512 bytes).

The non-512 byte part of the transfer is sent first. The remaining bytes
to be transferred in the current burst is stored in the 'remainder'
field.

With this method, the read_u32 field is no longer necessary, and is
removed.

This was tested on imx6 solo and imx6 quad.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The spi_imx_can_dma function computes the watermark level so that
the transfer will fit in exactly N bursts (without a remainder).

The smallest watermark level possible being one FIFO entry per burst, we
can't never have a case where the transfer size isn't divsiible by 1.

Remove the extra check for the wml being different than 0.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The SPI core enforces that we always use the next power-of-two number of
bytes to store words. As a result, a 24 bits word will be stored in 4
bytes.

This commit fixes the spi_imx_bytes_per_word function to return the
correct number of bytes.

This also allows to get rid of unnecessary checks in the can_dma
function, since the SPI core validates that we always have a transfer
length that is a multiple of the number of bytes per word.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The dynamic bursts mode allows to group together multiple words into a
single burst. To do so, it's necessary that words can be packed into the
32-bits FIFO entries, so we can't allow using this mode with bit_per_words
different to 8, 16 or 32.

This prevents shitfing out extra clock ticks for transfers with
bit_per_word values not aligned on 8 bits.

With that , we are sure that only the correct number of bits is
shifted out at each transfer, so we don't need to mask out the remaining
parts of the words.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some fields in struct spi_imx_data are assigned a different value twice
in a row, in spi_imx_setupxfer.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This changes the data type of the flags field in struct spi_bitbang from
u8 to u16. This matches the size of the mode field of struct spi_device
where these flags are also used.

This is done in preparation of adding a new SPI mode flag that will be
used with this field that would otherwise not fit in 8 bits.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge tag 'spi-dw-set-cs' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-4.19

spi: dw: Allow custom set_cs_callback

Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.

Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Upper layer users of SPI device drivers may rely on 'actual_length',
so it is important that information is correctly reported. One such
example is spi_mem_exec_op() function that will fail if
'actual_length' of the data transferred is not what was requested. Add
necessary code to populate 'actual_length.

Cc: Mark Brown <broonie@kernel.org>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: cphealy@gmail.com
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add "rockchip,px30-spi", "rockchip,rk3066-spi" for spi on px30 platform.
Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Registers of DSPI should not be accessed before enabling its clock.  On
Toradex Colibri VF50 on Iris carrier board this could be seen during
bootup as imprecise abort:

    Unhandled fault: imprecise external abort (0x1c06) at 0x00000000
    Internal error: : 1c06 [#1] ARM
    Modules linked in:
    CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.39-dirty #97
    Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
    Backtrace:
    [<804166a8>] (regmap_write) from [<80466b5c>] (dspi_probe+0x1f0/0x8dc)
    [<8046696c>] (dspi_probe) from [<8040107c>] (platform_drv_probe+0x54/0xb8)
    [<80401028>] (platform_drv_probe) from [<803ff53c>] (driver_probe_device+0x280/0x2f8)
    [<803ff2bc>] (driver_probe_device) from [<803ff674>] (__driver_attach+0xc0/0xc4)
    [<803ff5b4>] (__driver_attach) from [<803fd818>] (bus_for_each_dev+0x70/0xa4)
    [<803fd7a8>] (bus_for_each_dev) from [<803fee74>] (driver_attach+0x24/0x28)
    [<803fee50>] (driver_attach) from [<803fe980>] (bus_add_driver+0x1a0/0x218)
    [<803fe7e0>] (bus_add_driver) from [<803fffe8>] (driver_register+0x80/0x100)
    [<803fff68>] (driver_register) from [<80400fdc>] (__platform_driver_register+0x48/0x50)
    [<80400f94>] (__platform_driver_register) from [<8091cf7c>] (fsl_dspi_driver_init+0x1c/0x20)
    [<8091cf60>] (fsl_dspi_driver_init) from [<8010195c>] (do_one_initcall+0x4c/0x174)
    [<80101910>] (do_one_initcall) from [<80900e8c>] (kernel_init_freeable+0x144/0x1d8)
    [<80900d48>] (kernel_init_freeable) from [<805ff6a8>] (kernel_init+0x10/0x114)
    [<805ff698>] (kernel_init) from [<80107be8>] (ret_from_fork+0x14/0x2c)

Cc: <stable@vger.kernel.org>
Fixes: 5ee67b58 ("spi: dspi: clear SPI_SR before enable interrupt")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Intel Ice Lake SPI host controller follows the Intel Cannon Lake but the
PCI IDs are different. Add the new PCI IDs to the driver supported
devices list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org