Remove unused rocker_port parameter from rocker_port_kfree.
Also remove the rocker_port parameter from callers of rocker_port_kfree
where the parameter it is now unused.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

API compliance scanning with coccinelle flagged:
./net/irda/timer.c:63:35-37: use of msecs_to_jiffies probably perferable

Converting milliseconds to jiffies by "val * HZ / 1000" technically
is not a clean solution as it does not handle all corner cases correctly.
By changing the conversion to use msecs_to_jiffies(val) conversion is
correct in all cases. Further the () around the arithmetic expression
was dropped.

Patch was compile tested for x86_64_defconfig + CONFIG_IRDA=m

Patch is against 4.1-rc4 (localversion-next is -next-20150522)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These two uses seem to have had carriage returns removed.
Make these entries like all the others in this file.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

API compliance scanning with coccinelle flagged:

Converting milliseconds to jiffies by "val * HZ / 1000" is technically
is not a clean solution as it does not handle all corner cases correctly.
By changing the conversion to use msecs_to_jiffies(val) conversion is
correct in all cases.

in the current code:
  mod_timer(&self->rx_defer_timer, jiffies + (10 * HZ / 1000));
for HZ < 100 (e.g. CONFIG_HZ == 64|32 in alpha) this effectively results
in no delay at all.

Patch was compile tested for x86_64_defconfig (implies CONFIG_USB_IRDA=m)

Patch is against 4.1-rc4 (localversion-next is -next-20150522)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Network managers like netifd (used in OpenWRT for instance) try to
configure interface options after creation but before setting the
interface up.

Unfortunately the sysfs / bridge currently only allows to configure the
hash_max and multicast_router options when the bridge interface is up.
But since br_multicast_init() doesn't start any timers and only sets
default values and initializes timers it should be save to reconfigure
the default values after that, before things actually get active after
the bridge is set up.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>

since commit 6aafeef0 ("netfilter: push reasm skb through instead of
original frag skbs") we will end up sometimes re-fragmenting skbs
that we've reassembled.

ipv6 defrag preserves the original skbs using the skb frag list, i.e. as long
as the skb frag list is preserved there is no problem since we keep
original geometry of fragments intact.

However, in the rare case where the frag list is munged or skb
is linearized, we might send larger fragments than what we originally
received.

A router in the path might then send packet-too-big errors even if
sender never sent fragments exceeding the reported mtu:

mtu 1500 - 1500:1400 - 1400:1280 - 1280
     A         R1         R2        B

1 - A sends to B, fragment size 1400
2 - R2 sends pkttoobig error for 1280
3 - A sends to B, fragment size 1280
4 - R2 sends pkttoobig error for 1280 again because it sees fragments of size 1400.

make sure ip6_fragment always caps MTU at largest packet size seen
when defragmented skb is forwarded.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable irq_coalesce is bool type.
So assign the value true instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable separate_tx_rx_irq is bool type so assigning true
instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Martin KaFai Lau says:

====================
ipv6: Only create RTF_CACHE route after encountering pmtu exception

v4 -> v5:
- Patch 1 is new. Clean up the ipv6_select_ident() and ip6_fragment().

- Further simplify the newly added rt6_get_pcpu_route().  If there is a
  'prev' after cmpxchg, return prev instead of the newly created percpu
  clone.

v3 -> v4:
- Patch 8 is new. It keeps track of the DST_NOCACHE routes in a list to handle
  the iface down/unregister event.

- Remove rcu from the newly added rt6i_pcpu variable.  It is not needed
  because it has already been protected by the existing reader/writer lock.

- Thanks to 'Julian Anastasov <ja@ssi.bg>' for testing the FLOWI_FLAG_KNOWN_NH
  patches.

v2 -> v3:
- Patch 5 to 7 are new.  They take care of cases where the daddr in
  skb is not the one used to do the route look-up.  There is also
  related changes to rt6_nexthop() since v2 which is in patch 2/9.
  Thanks to 'Julian Anastasov <ja@ssi.bg>' for pointing it out.

- Fix a few problems in __ip6_rt_update_pmtu(), like setting the expire
  and mtu before inserting to the tree and don't do dst_destroy() after
  tree insertion failure.  Also update the rt6i_pmtu in fib6_add_rt2node().
  Thanks to 'Steffen Klassert <steffen.klassert@secunet.com>' for pointing
  it out.

- Merge ip6_pmtu_rt_cache_alloc() into ip6_rt_cache_alloc().

v1 -> v2:
- Move the /128 route bug fixes to another series (accepted).
- Create a function for checking (rt6i_flags & (RTF_NONEXTHOP | RTF_GATEWAY)).
- Avoid shuffling the skb network_header.  Instead, change the function
  signature to take iph instead of skb.

- Many Thanks to 'Hannes Frederic Sowa <hannes@stressinduktion.org>' on
  reviewing v1 and v2 and giving advice.

--Martin

~~~ start: v1 compose message (with the out-dated parts removed) ~~~

This series is to avoid creating a RTF_CACHE route whenever we are consulting
the fib6 tree with a new destination.  Instead, only create RTF_CACHE route
when we see a pmtu exception.

Out of all ipv6 RTF_CACHE routes that are created, the percentage that has a
different mtu is very small. In one of our end-user facing proxy server,
only 1k out of 80k RTF_CACHE routes have a smaller MTU.  For our DC
traffic, there is no mtu exception.

A large fib6 tree has problems like, 'ip -6 r show' takes a long time.
gc may kick in too often.  Also, when a service has restarted and a lot
of new TCP conn requests come in, it creates pressure on the tree by inserting
a lot of RTF_CACHE in a short time and it currently requires a write lock
to do that.

The first few patches are prep works to remove assumption that the
returned rt is always RTF_CACHE.

The patch 'ipv6: Only create RTF_CACHE routes after encountering pmtu exception'
do the lazy RTF_CACHE route creation.

The following patches added percpu rt to compensate the performance loss after
doing the RTF_CACHE lazy creation.

Here is some numbers of the udpflood test.  The udpflood has been
slightly modified to have a time limit instead of count limit.

A /64 via gateway route is used for the test. Each udpflood uses 10000 dst
addresses.  The dst addresses of different udpflood processes do not overlap
with each other.

1                    16M                          15M
10                   61M                          61M
20                   65M                          62M
40                   88M                          83M

~~~ end: v1 compose message ~~~
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After the patch
'ipv6: Only create RTF_CACHE routes after encountering pmtu exception',
we need to compensate the performance hit (bouncing dst->__refcnt).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch breaks up ip6_rt_copy() into ip6_rt_copy_init() and
ip6_rt_cache_alloc().

In the later patch, we need to create a percpu rt6_info copy. Hence,
refactor the common rt6_info init codes to ip6_rt_copy_init().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch keeps track of the DST_NOCACHE routes in a list and replaces its
dev with loopback during the iface down/unregister event.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch always creates RTF_CACHE clone with DST_NOCACHE
when FLOWI_FLAG_KNOWN_NH is set so that the rt6i_dst is set to
the fl6->daddr.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Julian Anastasov <ja@ssi.bg>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The neighbor look-up used to depend on the rt6i_gateway (if
there is a gateway) or the rt6i_dst (if it is a RTF_CACHE clone)
as the nexthop address.  Note that rt6i_dst is set to fl6->daddr
for the RTF_CACHE clone where fl6->daddr is the one used to do
the route look-up.

Now, we only create RTF_CACHE clone after encountering exception.
When doing the neighbor look-up with a route that is neither a gateway
nor a RTF_CACHE clone, the daddr in skb will be used as the nexthop.

In some cases, the daddr in skb is not the one used to do
the route look-up.  One example is in ip_vs_dr_xmit_v6() where the
real nexthop server address is different from the one in the skb.

This patch is going to follow the IPv4 approach and ask the
ip6_pol_route() callers to set the FLOWI_FLAG_KNOWN_NH properly.

In the next patch, ip6_pol_route() will honor the FLOWI_FLAG_KNOWN_NH
and create a RTF_CACHE clone.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Julian Anastasov <ja@ssi.bg>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of doing the rt6->rt6i_node check whenever we need
to get the route's cookie.  Refactor it into rt6_get_cookie().
It is a prep work to handle FLOWI_FLAG_KNOWN_NH and also
percpu rt6_info later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch creates a RTF_CACHE routes only after encountering a pmtu
exception.

After ip6_rt_update_pmtu() has inserted the RTF_CACHE route to the fib6
tree, the rt->rt6i_node->fn_sernum is bumped which will fail the
ip6_dst_check() and trigger a relookup.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

A prep work for creating RTF_CACHE on exception only.  After this
patch, the same condition (rt->rt6i_flags & (RTF_NONEXTHOP | RTF_GATEWAY))
is checked twice. This redundancy will be removed in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

When creating a RTF_CACHE route, RTF_ANYCAST is set based on rt6i_dst.
Also, rt6i_gateway is always set to the nexthop while the nexthop
could be a gateway or the rt6i_dst.addr.

After removing the rt6i_dst and rt6i_src dependency in the last patch,
we also need to stop the caller from depending on rt6i_gateway and
RTF_ANYCAST.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the assumptions that the returned rt is always
a RTF_CACHE entry with the rt6i_dst and rt6i_src containing the
destination and source address.  The dst and src can be recovered from
the calling site.

We may consider to rename (rt6i_dst, rt6i_src) to
(rt6i_key_dst, rt6i_key_src) later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes the ipv6_select_ident() signature to return a
fragment id instead of taking a whole frag_hdr as a param to
only set the frag_hdr->identification.

It also cleans up ip6_fragment() to obtain the fragment id at the
beginning instead of using multiple "if" later to check fragment id
has been generated or not.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for flashing 10GBaseT adapter with BCM 84834 PHY and
Aquantia AQ1202 PHY.

Updating of the PHY firmware must happen before the INITIALIZE_CMD.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two more eBPF test cases for JITs, i.e. the second one revealed a
bug in the x86_64 JIT compiler, where only an int3 filled image from
the allocator was emitted and later wrongly set by the compiler as the
bpf_func program code since optimization pass boundary was surpassed
w/o actually emitting opcodes.

Interpreter:

  [   45.782892] test_bpf: #242 BPF_MAXINSNS: Very long jump backwards jited:0 11 PASS
  [   45.783062] test_bpf: #243 BPF_MAXINSNS: Edge hopping nuthouse jited:0 14705 PASS

After x86_64 JIT (fixed):

  [   80.495638] test_bpf: #242 BPF_MAXINSNS: Very long jump backwards jited:1 6 PASS
  [   80.495957] test_bpf: #243 BPF_MAXINSNS: Edge hopping nuthouse jited:1 17157 PASS

Reference: http://thread.gmane.org/gmane.linux.network/364729Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver updates 2015-05-22

The following patches are included in this driver update series:

- Retrieve and set an additional hardware feature setting
- Fix the initial mode/speed determination when auto-negotiation is
  disabled
- Add additional netif_dbg support to the driver

This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Change more netdev_dbg statements over to netif_dbg and add some new
netif_dbg statements to the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.

Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device private data structure contains all the defined hardware
features for the device. However one of the features is not set. Even
though the feature is not currently used, set it to avoid future
issues of the feature being checked thinking it has been properly set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send icmp pmtu error if we find that the largest fragment of df-skb
exceeded the output path mtu.

The ip output path will still catch this later on but we can avoid the
forward/postrouting hook traversal by rejecting right away.

This is what ipv6 already does.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hannes Frederic Sowa says:

====================
net: af_unix: zerocopy stream bits

This series implements zerocopy support for AF_UNIX SOCK_STREAM sockets.

Changelog in the specific patches. Thanks to all the reviewers!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

unix_stream_recvmsg is refactored to unix_stream_read_generic in this
patch and enhanced to deal with pipe splicing. The refactoring is
inneglible, we mostly have to deal with a non-existing struct msghdr
argument.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare skb_splice_bits to be able to deal with AF_UNIX sockets.

AF_UNIX sockets don't use lock_sock/release_sock and thus we have to
use a callback to make the locking and unlocking configureable.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements sendpage support for AF_UNIX SOCK_STREAM
sockets. This is also required for a complete splice implementation.

The implementation is a bit tricky because we append to already existing
skbs and so have to hold unix_sk->readlock to protect the reading side
from either advancing UNIXCB.consumed or freeing the skb at the socket
receive tail.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
ath10k:

* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware

ath9k:

* spectral scan: add support for multiple FFT frames per report

iwlwifi:

* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure

brcmfmac:

* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4: Enable single ported VFs over IB ports

This series further enhances the support for mlx4 single ported VFs
introduced in 3.15 to work over IB ports too.

Just as quick reminder, the ConnectX3 device family exposes one PCI device
which serves both ports.

This can be non-optimal under virtualization schemes where the admin
would like the VF to expose one interface to the VM, etc.

Since all the VF interaction with the firmware passes through the PF
driver, we can emulate to the VF they have one port, and further create
a set of the VFs which act on port1 of the device and another set which
acts on port2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the limitation that disallows configuring single ported VFs
in the presence of IB ports, after addressing the issues that
prevented that to work.

SMI (QP0) requests/responses are still not supported for single
ported IB VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's legal for drivers to provide the QP port through the
QPC schedule-queue field on the reset-to-init QP state change.

Add adjusting of the schedule queue port in the SRIOV wrapper
for that operation too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some VF drivers flow set the schedule queue in the QP context but
without setting none of OPTPAR_SCHED_QUEUE or OPTPAR_PRIMARY_ADDR_PATH.

To allow for such non-modified drivers to function as single ported
IB VFs, we must adjust the schedule queue port whenever being set,
e.g as currently done for single ported Eth VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of enabling single ported VFs over IB ports we need to handle
some of the flows for generting EQ events for VFs which don't come
into play under Eth ports.

This mainly includes port management events derived from changes of the
phyiscal port (lid change, client re-register, down/up, etc), VF pkey table
changes and VF guid changes initiated by the IB driver.

(1) make sure that events are generated only for VFs sitting on
    the relevant physical port (under the ALL_SLAVES flow).

(2) before generating the event, convert from physical (one or two)
    to VF port (always equals one).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

When multiplexling a MAD sent from VF, we should convert the port used
by the guest to send the packet to the actual physical port which will be
used to transmit the packet, before building the relevant address-handle (AH).

This is needed under VPI for single ported VFs, since the code that builds
the AH (mlx4_ib_query_ah()) makes decisions based on the input port. If we
use the port number provided by the guest, it might have different protocol
vs. the one this packat has to go from, and hence the result could be wrong.

So far, the conversion was done after the AH was built and it worked for
single ported Eth VFs which were not enabled under VPI. When adding support
for single ported IB VFs and VPI, we hit that.

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Single port VFs always provide port = 1 (even if the actual physical
port used is port 2). As such, we need to convert the port provided
by the VF to the physical port before calling into the firmware.

It turns out that the Linux mlx4 VF RoCE driver maintains a copy of
the GID table and hence this change became critical only for single
ported IB VFs, but it could be needed for other RoCE VF drivers too.

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>