This chip family supports LDPC so enable it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firwmare now allows the driver to disable dummy
notifications. These notifications sent by the firmware
are an overhead for slow buses. They are still useful for
fast buses.
Add a hardware switch to prevent these notifications only
on devices that work on slow buses.
Signed-off-by: Eran <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Edit some 8000 series PCI IDs and add configuration to
Dual Band Wireless N 8260 devices.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use LDPC for Tx and publish support for Rx in case the chip
supports LDPC. Enable it for the 7265 family.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The idea here is to translate a value of 0 received from
the firmware to the lowest rssi figure. As rx_status->chain_signal
is a signed byte the lowest possible value is -128 and not -256.
-256 was causing 0 to get stored in the signed byte.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This change does the following:
1) Add a new 7265 series PCI ID
2) Add two new 3160 series PCI IDs
3) Add the new 3165 series PCI IDs and configurations
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In
https://bugzilla.kernel.org/show_bug.cgi?id=84031,
the submitter said that disabling power saving helped,
do just that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

smps_mode is used uninitialized in a debug statement in AP
mode, so always initialize it.

While at it, fix a typo.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The latter is meant for software implementation of power
save and is not per-virtual interface. Since our driver
supports multiple virtual interfaces, we need to use
vif->bss_conf.dtim_period.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Using the LQ table which is initially set according to
the rssi could lead to EAPOLs being sent in high legacy
rates like 54mbps.
It's better to avoid sending EAPOLs in high rates as it reduces
the chances of a successful 4-Way handshake.
Avoid this and treat them like other mgmt frames which would
initially get sent at the basic rate.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When mac80211 requests multiple BSS config changes, as for example
while associating, we ignore power management and QoS changes and
only apply them later. Fix that by removing the "else" and making
the conditions independent.

Also move it after (potential) beacon filter enablement to have
that already enabled when going into power management code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The chip is able to transmit up to 22dBm, so set
the constant appropriately.

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This code was broken on big endian systems. Sparse didn't
catch the bug since the firmware command was not tagged as
little endian.
Fix the bug for big endian systems and tag the field in the
firmware command to prevent such issues in the future.

Cc: stable@vger.kernel.org [3.14+]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In commit cad3f08c (iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when
forced_assoc_off is set) the code to set the MAC_FILTER_IN_BEACON flag
was accidentally moved to the main block of the if statement, while it
should be in the else block instead.  Move it to the right place.

Fixes: cad3f08c ("iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when forced_assoc_off is set")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The variable 'u32 mode' exists twice, the latter shadowing
the former - remove the latter since there's no need for
two variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The auxiliary station is being handled using the internal
station helper functions, clean that up and make the helpers
static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Unify all the functions that handle the per-interface broadcast
station and make them have mvm and vif parameters. While at it,
add a new function to allocate the broadcast station instead of
open-coding it, and make the combined alloc+send and free+send
functions use the alloc/free & send functions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There are a few places that can call the function
iwl_mvm_mac_get_queues_mask() instead of open-coding the
equivalent, so do that. This requires changing it to return
the multicast queue as part of the bitmap, which broke GO
mode because including it in the broadcast station queues
seems to confuse the firmware, so work around that.

Also, the API defines that the CAB queue shouldn't be
included in the TFD queue mask, adjust the comment
accordingly (not a bug).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of checking whether a given station is the first to
be added on a client interface check for the new TDLS flag
and warn in the unexpected cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The queue handling is a bit unclear - we have an array for
stop_count[IWL_MAX_HW_QUEUES] but indices really are the
mac80211 queue numbers. Change the array to be only of the
right size for mac80211 queues (IEEE80211_MAX_QUEUES) and
rename it to be clearer.

While at it, also remove the unused transport queue stop
bitmap in mvm.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Move all FIFO definitions together into the firmware API
header file and use the same enum/naming scheme for the
command FIFO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware would like to have a MAC context (unassoc)
before the AP station is removed (we do this) but would
like to keep the BSSID until after it is removed, so we
need to send two commands - one with the BSSID before
and one without the BSSID after.

In order to do this, we need to store the BSSID as it
will have been cleared by mac80211 by the time we get
notified of the disassociation. Also pass it around as
an override to the various functions needing it, and
keep taking it from the mac80211 data otherwise. This
avoids having to keep track of the BSSID in all modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

During a channel switch we should tell the firmware to disable TX
temporarily and re-enable it after the switch is done.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the firmware is handling this, but that is wrong as it then
needs to assume a certain command queue, therefore this should be in
the driver; add it here so it can be removed from the firmware in the
future.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently a valid sta_id is assumed to mean that the queue is
meant to also be aggregated, but that assumption will not be
true in the future, so don't make it in the lower level but
only in the inline wrapper.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In a later patch, the hardware configuration will be moved to
firmware. Prepare for this by allowing hardware configuration
in the transport to be skipped by not passing a configuration
on enable and passing configure_scd=false on disable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The tracepoints that are only used in code linked with iwlwifi.ko,
as are the tracepoints, don't need to be exported, so don't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to follow more easily what's going on, add some
debug statements to the quota allocation algorithm.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable fragmented scan that was diabled due to a FW bug.
New fixed FWs use a TLV bit to advertise fragmented scan support.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of having all arguments passed to the function,
add a struct to hold them and only pass some directly.

This will make future work in this area cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Configuring the hw scheduler during queue enablement is done by
writing the appropriate values to the scheduler peripherals, and
it is essentially the same for all buses.

Whenever writing is done via the standard iwl_write_prph, we can
avoid duplicating the code for each bus. Those operations are
queue deactivation, RA/TID mapping, chain-building settings,
enabling/disabling aggregations and activating/deactivating the
TX FIFOs.

Consolidate this code using static inlines in a new header file.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Make sure that when running the TDLS discovery session
protection - the time event that ensures we remain on channel
has been scheduled and started running before leaving.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We need to disable PS when a monitor vif is active or, in the future,
when a channel switch is happening.  Add a boolean to mvmvif that
allows PS to be disabled generically.  Additionally, make the monitor
interface use this new flag when it gets activated.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new iwl_mvm_power_update_ps() function that allows only ps to be
updated according to changes in the vifs.  This allows us to disable
ps only without affecting the pm values of the vifs (and to avoid
sending unnecessary MAC_PM_POWER_TABLE commands to the firmware).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Separate the ps part of iwl_mvm_power_set_pm() into a new
iwl_mvm_power_set_ps() function.  This will enable us to update the ps
part independently from the rest, which is needed by CSA (at least).

This required a bit of refactoring and the creation of a new iterator
function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If a monitor interface is added and then removed, we don't reset the
mvm->ps_disabled flag, so we never re-enable power saving.  Fix that
and rearrange the code a bit.

Additionally, fix a small indentation mistake in the
iwl_mvm_power_set_pm() function declaration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If recovery happened after mvm entered d0i3 (e.g.
due to sysassert when releasing the bus), the
mvm->state wasn't cleared properly, causing the
ongoing recovery to fail (due to iwl_mvm_ref_sync
failure).

This in turn fails the ongoing recovery, and triggers
a reprobe, which terminates any ongoing wifi activity.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>