Currently acpi_gsb_i2c_read_bytes() directly returns i2c_transfer's return
value. i2c_transfer returns a value < 0 on error and 2 (for 2 successfully
executed transfers) on success. But the ACPI code expects 0 on success, so
currently acpi_gsb_i2c_read_bytes()'s caller does:

        if (status > 0)
                status = 0;

This commit makes acpi_gsb_i2c_read_bytes() return a value which can be
directly consumed by the ACPI code, mirroring acpi_gsb_i2c_write_bytes(),
this commit also makes acpi_gsb_i2c_read_bytes() explitcly check that
i2c_transfer returns 2, rather then accepting any value > 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

acpi_gsb_i2c_write_bytes() returns i2c_transfer()'s return value, which
is the number of transfers executed on success, so 1.

The ACPI code expects us to store 0 in gsb->status for success, not 1.

Specifically this breaks the following code in the Thinkpad 8 DSDT:

            ECWR = I2CW = ECWR /* \_SB_.I2C1.BAT0.ECWR */
            If ((ECST == Zero))
            {
                ECRD = I2CR /* \_SB_.I2C1.I2CR */
            }

Before this commit we set ECST to 1, causing the read to never happen
breaking battery monitoring on the Thinkpad 8.

This commit makes acpi_gsb_i2c_write_bytes() return 0 when i2c_transfer()
returns 1, so the single write transfer completed successfully, and
makes it return -EIO on for other (unexpected) return values >= 0.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Document RZ/G2M (R8A774A1) I2C compatibility with the relevant driver
dt-bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Document RZ/G2M (R8A774A1) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Always update the stopped state when busy status have been checked.
This is identical to what was done before, with the exception of error
handling.
Without this change, some errors cause the stopped state to be left in
incorrect state in i2c_imx_stop(), i2c_imx_dma_read(), i2c_imx_read() and
i2c_imx_xfer().
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read.  When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).

Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

The pasemi smbus controller uses PCI_FUNC(dev->devfn) to define which
number bus to attach to, however this fails when something else is
probed first, for example an ATI Radeon graphics card will claim 9 or
10 busses, including the ones the pasemi wants.
Patch the driver to call i2c_add_adapter rather than
i2c_add_numbered_adapter.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Replace short statement in comment with proper SPDX license tag.

Note, for i2c-desingware-slave.c the identifier is chosen
in accordance with MODULE_LICENSE() macro since it is visible to user.
Another point to this choice is that the header seems to be copy'n'paste
from the other file of this very driver.
Acked-by: Luis Oliveira <Luis.Oliveira@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

There are two drivers already using the SDA hold time setting.
It might be more in the future, thus, make I2C core to parse the setting
for us if provided by firmware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Some adapters do not support a message length of 0. Add this as a quirk
so drivers don't have to open code it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This commit fixes this sparse warning:
drivers/i2c/busses/i2c-aspeed.c:875:38: warning: incorrect type in assignment (different modifiers)
drivers/i2c/busses/i2c-aspeed.c:875:38:    expected unsigned int ( *get_clk_reg_val )( ... )
drivers/i2c/busses/i2c-aspeed.c:875:38:    got void const *const data
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Simplify the probe function of the pca954x driver

Add Actions Semiconductor Owl family S900 I2C driver.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add devicetree binding for Actions Semiconductor Owl I2C controller
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This bus driver supports the GENI based i2c hardware controller in the
Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
module supporting a wide range of serial interfaces including I2C. The
driver supports FIFO mode and DMA mode of transfer and switches modes
dynamically depending on the size of the transfer.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
[wsa: squashed the MAINTAINER addition and a RPM fix by Evan Green]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This creates a struct device *dev helper variable in probe()
which IMO makes the code less cluttered and easier to read.
Also rename the of_node veriable to the common shortform "np"
(node pointer).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[peda: slightly edited commit message and removed some surplus newlines]
Signed-off-by: Peter Rosin <peda@axentia.se>

Merge tag 'at24-4.19-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-4.19

at24: updates for v4.19

New property: 'address-width' which allows to specify the number of
addressing bits. Up until now we only could choose one of the defined
models and rely on the flags specified in its corresponding chip data
structure.

Provide a flexible way to determine the addressing bits of eeprom.
Pass the addressing bits to driver through address-width property.
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Currently the only way to use a variant of a supported model with
a different address width is to define a new compatible string and
the corresponding chip data structure.

Provide a flexible way to specify the size of the address pointer
by defining a new property: address-width.
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[Bartosz: fixed the commit message]
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull NVMe fixes from Christoph Hellwig:

 - fix a regression in 4.18 that causes a memory leak on probe failure
   (Keith Bush)

 - fix a deadlock in the passthrough ioctl code (Scott Bauer)

 - don't enable AENs if not supported (Weiping Zhang)

 - fix an old regression in metadata handling in the passthrough ioctl
   code (Roland Dreier)

* tag 'nvme-for-4.18' of git://git.infradead.org/nvme:
  nvme: fix handling of metadata_len for NVME_IOCTL_IO_CMD
  nvme: don't enable AEN if not supported
  nvme: ensure forward progress during Admin passthru
  nvme-pci: fix memory leak on probe failure

Pull vfs fixes from Al Viro:
 "Fix several places that screw up cleanups after failures halfway
  through opening a file (one open-coding filp_clone_open() and getting
  it wrong, two misusing alloc_file()). That part is -stable fodder from
  the 'work.open' branch.

  And Christoph's regression fix for uapi breakage in aio series;
  include/uapi/linux/aio_abi.h shouldn't be pulling in the kernel
  definition of sigset_t, the reason for doing so in the first place had
  been bogus - there's no need to expose struct __aio_sigset in
  aio_abi.h at all"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  aio: don't expose __aio_sigset in uapi
  ocxlflash_getfile(): fix double-iput() on alloc_file() failures
  cxl_getfile(): fix double-iput() on alloc_file() failures
  drm_mode_create_lease_ioctl(): fix open-coded filp_clone_open()

kernel_wait4() expects a userland address for status - it's only
rusage that goes as a kernel one (and needs a copyout afterwards)

[ Also, fix the prototype of kernel_wait4() to have that __user
  annotation   - Linus ]

Fixes: 92ebce5a ("osf_wait4: switch to kernel_wait4()")
Cc: stable@kernel.org # v4.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC fixes from Olof Johansson:

 - Fix interrupt type on ethernet switch for i.MX-based RDU2

 - GPC on i.MX exposed too large a register window which resulted in
   userspace being able to crash the machine.

 - Fixup of bad merge resolution moving GPIO DT nodes under pinctrl on
   droid4.

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: imx6: RDU2: fix irq type for mv88e6xxx switch
  soc: imx: gpc: restrict register range for regmap access
  ARM: dts: omap4-droid4: fix dts w.r.t. pwm

Pull x86 fix from Ingo Molnar:
 "A single fix for a MCE-polling regression, which prevented the
  disabling of polling"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/MCE: Remove min interval polling limitation

Pull x86 pti fixes from Ingo Molnar:
 "An APM fix, and a BTS hardware-tracing fix related to PTI changes"

* 'x86-pti-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apm: Don't access __preempt_count with zeroed fs
  x86/events/intel/ds: Fix bts_interrupt_threshold alignment

Pull scheduler fixes from Ingo Molnar:
 "Two fixes: a stop-machine preemption fix and a SCHED_DEADLINE fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Fix switched_from_dl() warning
  stop_machine: Disable preemption when waking two stopper threads

Pull core kernel fixes from Ingo Molnar:
 "This is mostly the copy_to_user_mcsafe() related fixes from Dan
  Williams, and an ORC fix for Clang"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm/memcpy_mcsafe: Fix copy_to_user_mcsafe() exception handling
  lib/iov_iter: Fix pipe handling in _copy_to_iter_mcsafe()
  lib/iov_iter: Document _copy_to_iter_flushcache()
  lib/iov_iter: Document _copy_to_iter_mcsafe()
  objtool: Use '.strtab' if '.shstrtab' doesn't exist, to support ORC tables on Clang

Pull powerpc fixes from Michael Ellerman:
 "Two regression fixes, one for xmon disassembly formatting and the
  other to fix the E500 build.

  Two commits to fix a potential security issue in the VFIO code under
  obscure circumstances.

  And finally a fix to the Power9 idle code to restore SPRG3, which is
  user visible and used for sched_getcpu().

  Thanks to: Alexey Kardashevskiy, David Gibson. Gautham R. Shenoy,
  James Clarke"

* tag 'powerpc-4.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Fix save/restore of SPRG3 on entry/exit from stop (idle)
  powerpc/Makefile: Assemble with -me500 when building for E500
  KVM: PPC: Check if IOMMU page is contained in the pinned physical page
  vfio/spapr: Use IOMMU pageshift rather than pagesize
  powerpc/xmon: Fix disassembly since printf changes