- 24 Jun, 2013 8 commits
-
-
Gabor Juhos authored
The current code uses the same index value both for the channel information array and for the TX power table. The index starts from 14, however the index of the TX power table must start from zero. Fix it, in order to get the correct TX power value for a given channel. The changes in rt61pci.c and rt73usb.c are compile tested only. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Cc: stable@vger.kernel.org Acked-by:
Stanislaw Gruszka <stf_xl@wp.pl> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Dan Carpenter authored
Smatch complains that this is a read past the end of the array. It turns out we are printing the wrong array here. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Sujith Manoharan authored
Since platform support is required for WoW, identify and and enable Wow only for supported cards. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Solomon Peachy authored
Most of these relate to endianness problems, and are purely cosmetic. But a couple of them were legit -- listen interval parsing and some of the rate selection code would malfunction on BE systems. There's still one cosmetic warning remaining, in the (admittedly) ugly code in cw1200_spi.c. It's there because the hardware needs 16-bit SPI transfers, but many SPI controllers only operate 8 bits at a time. If there's a cleaner way of handling this, I'm all ears. Signed-off-by:
Solomon Peachy <pizza@shaftnet.org> Signed-off-by:
-
Wei Yongjun authored
Fix to return -ENOMEM in the ipw_rx_queue_alloc() error handling case instead of 0, as done elsewhere in this function. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Felix Fietkau authored
ath_tx_txqaddbuf assumes that all the linked buffers in the queue passed to it are part of the same A-MPDU or MPDU. The CAB queue rework violates this assumption, which can cause the internal queue depth to go negative. Fix this by increasing the counter for all slots of [bf, bf->bf_lastbf] Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Ben Greear authored
This provides some of the same info found in the ath9k_htc debugfs through the standard ethtool stats API. This logic is only supported when ath9k_htc debugfs kernel feature is enabled, since that is the only time stats are actually gathered. Signed-off-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
-
Ben Greear authored
Signed-off-by:
-
- 19 Jun, 2013 5 commits
-
-
Amitkumar Karwar authored
After receiving channel switch announcement from AP, scan and association on that channel is blocked for DFS_CHAN_MOVE_TIME (10 seconds). Hence station will be able to connect to the AP, once it is moved to new channel. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
Paul Stewart <pstew@chromium.org> Signed-off-by:
-
Amitkumar Karwar authored
This patch adds code to parse requested AP's 11h capabilities and add 11h information in association request. Also, deauth is sent to the AP after receiving channel switch announcement event from firmware. This happens when AP advertises WLAN_EID_CHANNEL_SWITCH IE in it's beacon. Signed-off-by:
-
Antonio Quartulli authored
Do not unconditionally access the chan variable in brcmf_cfg80211_mgmt_tx() as it may be NULL. Use freq instead. Introduced by c2ff8cad ("brcm80211: make mgmt_tx in brcmfmac accept a NULL channel") Reported-by:
Antonio Quartulli <antonio@open-mesh.com> Signed-off-by:
-
Amitkumar Karwar authored
Use negative check (if(!bss_desc)) and return failure instead of failing a NULL check later in mwifiex_check_network_compatibility() routine. Signed-off-by:
-
Larry Finger authored
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the same condition twice. The problem was found using cppcheck-1.49, and the proper fix was verified against the pre-mac80211 version of the code. This patch was originally included as commit 1288aa4e, but was accidentally reverted in a later patch. Reported-by: David Binderman <dcb314@hotmail.com> [original report] Reported-by: Andrea Morello <andrea.merello@gmail.com> [report of accidental reversion] Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: stable <stable@vger.kernel.org> [back to 2.6.39] Signed-off-by:
-
- 18 Jun, 2013 21 commits
-
-
Franky Lin authored
Add scatter gather list support for better rx glom performance. Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
Franky Lin <frankyl@broadcom.com> Signed-off-by:
-
Franky Lin authored
Introducing a new SDIO block data access interface function brcmf_sdio_buffrw. It will act as a unified interface function for any block data access to WiFi dongle through SDIO interface. This patch enables the support for single skb transmission. Reviewed-by:
-
Franky Lin authored
There is an ID table registered to SDIO stack which consists of all SDIO devices supported by brcmfmac. It is not necessary to have an extra check. Reviewed-by:
-
Arend van Spriel authored
Instead of allocating an empty list item and queue that for the dpc data worker to dequeue an atomic counter is used. Reviewed-by:
-
Arend van Spriel authored
Just cleaning up and being consistent in naming operations related to struct brcmf_fws_mac_descriptor objects. Reviewed-by:
-
Arend van Spriel authored
The firmware-signalling code used NL80211_NUM_ACS, but it has its own definition enum brcmf_fws_fifo, which is more appropriate to use. This effectively removes the need to include nl80211.h. Reviewed-by:
-
Arend van Spriel authored
The term prec (precedence) is different from the fifo number. Rename use of prec with fifo to be consistent and clear. Reviewed-by:
-
Hante Meuleman authored
The firmware will sent an event message when bc/mc traffic should be sent to the device using credit mechanism. Reviewed-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
CUS217 is a card based on AR9462. Signed-off-by:
-
Dan Carpenter authored
This should be >= ARRAY_SIZE() instead of > ARRAY_SIZE(). Signed-off-by:
-
Rafał Miłecki authored
This allows writing MTD driver working as a platform driver. In platform_data it will receive struct ssb_sflash, which contains all important data about flash (window, size). Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Sujith Manoharan authored
CUS198 and CUS230 are similar cards, both are AR9485 + xLNA solutions. But, the subsystem IDs differ - identify CUS230 explicitly to make things clearer. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Sujith Manoharan authored
Use the REGULATORY debug level to print the target power details. EEPROM can be used for other purposes and this spams the log. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
-
-
-
- 17 Jun, 2013 6 commits
-
-
Larry Finger authored
This is a new device for this driver. Reported-by:
Tobias Kluge <zielscheibe@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
This data allow writing for example MTD driver. Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Broadocm updated their code, this may be needed for newer hardware or some corner cases. Signed-off-by:
-
Sujith Manoharan authored
The commit "ath9k: Fix ANI monitoring" reverted an earlier commit that adjusted ANI to improve performance. But, this causes adverse effects in AP mode (as reported by Felix based on an OpenWrt report). Use the older INI/period configuration for now until more testing is done. Cc: Felix Fietkau <nbd@openwrt.org> Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
-
