Skip to content

L
linux
Switch branch/tag
  1. 21 Jun, 2016 4 commits
  3. 20 Jun, 2016 7 commits
  5. 19 Jun, 2016 1 commit
  7. 17 Jun, 2016 10 commits
  9. 16 Jun, 2016 7 commits
  11. 15 Jun, 2016 4 commits
  13. 14 Jun, 2016 7 commits
    • Lyude's avatar
      drm/i915/ilk: Don't disable SSC source if it's in use · 1c1a24d2
      Lyude authored 
      Thanks to Ville Syrjälä for pointing me towards the cause of this issue.

Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:

[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config]     FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config]     scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A

Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.

A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.

Changes since v4:
 - Fix calculation of final for systems with LVDS panels (fixes BUG() on
   CI test suite)
Changes since v3:
 - Move temp variable into loop
 - Move checks for using_ssc_source to after we've figured out has_ck505
 - Add using_ssc_source to debug output
Changes since v2:
 - Fix debug output for when we disable the CPU source
Changes since v1:
 - Leave the SSC source clock on instead of just shutting it off on all
   of the DPLL configurations.

Cc: stable@vger.kernel.org
Reviewed-by: default avatarVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: default avatarLyude <cpaul@redhat.com>
Signed-off-by: default avatarDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465916649-10228-1-git-send-email-cpaul@redhat.com
      1c1a24d2
    • Daniel Vetter's avatar
      Merge tag 'sphinx-4.8' of git://git.lwn.net/linux into topic/drm-misc · db5dfef7
      Daniel Vetter authored 
      Stable tag for sphinx work

Pull current state of the sphinx rework from Jonathan into drm-misc so
that we can start converting gpu.tmpl.
Signed-off-by: default avatarDaniel Vetter <daniel.vetter@intel.com>
      db5dfef7
    • Daniel Vetter's avatar
      drm/virtio: Don't reinvent a flipping wheel · 0d841ac0
      Daniel Vetter authored 
      Now that the core helpers support nonblocking atomic commits there's
no need to invent that wheel separately (instead of fixing the bug in
the atomic implementation of virtio, as it should have been done!).

v2: Rebased on top of

commit e7cf0963
Author: Gerd Hoffmann <kraxel@redhat.com>
Date:   Tue May 31 08:50:47 2016 +0200

virtio-gpu: add atomic_commit function

Cc: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: default avatarGerd Hoffmann <kraxel@redhat.com>
Reviewed-by: default avatarGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: default avatarDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465510073-20951-1-git-send-email-daniel.vetter@ffwll.ch
      0d841ac0
    • Dave Gordon's avatar
      drm/i915/guc: (re)initialise doorbell h/w when enabling GuC submission · 4d75787b
      Dave Gordon authored 
      During a hibernate/resume cycle, the whole system is reset, including
the GuC and the doorbell hardware. Then the system is booted up, drivers
are loaded, etc -- the GuC firmware may be loaded and set running at
this point. But then, the booted kernel is replaced by the hibernated
image, and this resumed kernel will also try to reload the GuC firmware
(which will fail). To recover, we reset the GuC and try again (which
should work). But this GuC reset doesn't also reset the doorbell
hardware, so it can be left in a state inconsistent with that assumed
by the driver and/or the newly-loaded GuC firmware.

It would be better if the GuC reset also cleared all doorbell state,
but that's not how the hardware currently works; also, the driver cannot
directly reprogram the doorbell hardware (only the GuC can do that).

So this patch cycles through all doorbells, assigning and releasing each
in turn, so that all the doorbell hardware is left in a consistent
state, no matter how it was programmed by the previously-running kernel
and/or GuC firmware.

v2: don't use kmap_atomic() now that client page 0 is kept mapped.
Signed-off-by: default avatarDave Gordon <david.s.gordon@intel.com>
Reviewed-by: default avatarTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: default avatarTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465837054-16245-2-git-send-email-david.s.gordon@intel.com
      4d75787b
    • Dave Gordon's avatar
      drm/i915/guc: replace assign_doorbell() with select_doorbell_register() · f10d69a7
      Dave Gordon authored 
      This version doesn't update the doorbell bitmap, as that will
be done when the selected doorbell is associated with a client.

The call is now slightly earlier, just on the general principle
that potentially-failing operations should be done as early as
possible, to eliminate late failures and simplify recovery.
Suggested-by: default avatarTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: default avatarDave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: default avatarTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: default avatarTvrtko Ursulin <tvrtko.ursulin@intel.com>
      f10d69a7
    • Dave Gordon's avatar
      drm/i915/guc: refactor doorbell management code · a667429b
      Dave Gordon authored 
      This patch refactors the driver's handling and tracking of doorbells, in
preparation for a later one which will resolve a suspend-resume issue.

There are three resources to be managed:
1. Cachelines: a single line within the client-object's page 0
   is snooped by doorbell hardware for writes from the host.
2. Doorbell registers: each defines one cacheline to be snooped.
3. Bitmap: tracks which doorbell registers are in use.

The doorbell setup/teardown protocol starts with:
1. Pick a cacheline: select_doorbell_cacheline()
2. Find an available doorbell register: assign_doorbell()
(These values are passed to the GuC via the shared context
descriptor; this part of the sequence remains unchanged).

3. Update the bitmap to reflect registers-in-use
4. Prepare the cacheline for use by setting its status to ENABLED
5. Ask the GuC to program the doorbell to snoop the cacheline

and of course teardown is very similar:
6. Set the cacheline to DISABLED
7. Ask the GuC to reprogram the doorbell to stop snooping
8. Record that the doorbell is not in use.

Operations 6-8 (guc_disable_doorbell(), host2guc_release_doorbell(), and
release_doorbell()) were called in sequence from guc_client_free(), but
are now moved into the teardown phase of the common function.

Steps 4-5 (guc_init_doorbell() and host2guc_allocate_doorbell()) were
similarly done as sequential steps in guc_client_alloc(), but since it
turns out that we don't need to be able to do them separately they're
now collected into the setup phase of the common function.

The only new code (and new capability) is the block tagged
    /* Update the GuC's idea of the doorbell ID */
i.e. we can now *change* the doorbell register used by an existing
client, whereas previously it was set once for the entire lifetime
of the client. We will use this new feature in the next patch.

v2: Trivial independent fixes pushed ahead as separate patches.
    MUCH longer commit message :) [Tvrtko Ursulin]
Signed-off-by: default avatarDave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: default avatarTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: default avatarTvrtko Ursulin <tvrtko.ursulin@intel.com>
      a667429b
    • Dave Gordon's avatar
      drm/i915/guc: move guc_ring_doorbell() nearer to callsite · 10d2c3e2
      Dave Gordon authored 
      Just code movement, no actual change to the function. This is in
preparation for the next patch, which will reorganise all the other
doorbell code, but doesn't change this function. So let's shuffle it
down near its caller rather than leaving it mixed in with the setup
code. Unlike the doorbell management code, this function is somewhat
time-critical, so putting it near its caller may even yield a tiny
performance improvement.
Signed-off-by: default avatarDave Gordon <david.s.gordon@intel.com>
Reviewed-by: default avatarTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: default avatarTvrtko Ursulin <tvrtko.ursulin@intel.com>
      10d2c3e2
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7