'cpu_data' is updated for policy->cpu first and then for all CPUs in
policy->cpus. policy->cpus is guaranteed to contain policy->cpu as well and so
the first write to 'cpu_data' for policy->cpu is redundant. Remove it.
Acked-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics
and a slightly buggy strncasecmp. The latter is the POSIX name, so
strnicmp was renamed to strncasecmp, and strnicmp made into a wrapper
for the new strncasecmp to avoid breaking existing users.

To allow the compat wrapper strnicmp to be removed at some point in
the future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch ensures the cpus to kexec/reboot at nominal frequency.
Nominal frequency is the highest cpu frequency on PowerPC at
which the cores can run without getting throttled.

If the host kernel had set the cpus to a low pstate and then it
kexecs/reboots to a cpufreq disabled kernel it would cause the target
kernel to perform poorly. It will also increase the boot up time of
the target kernel. So set the cpus to high pstate, in this case to
nominal frequency before rebooting to avoid such scenarios.

The reboot notifier will set the cpus to nominal frequncy.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Its possible today that the pstate of a core is held at a high even after the
entire core is hotplugged out if a load had just run on  the hotplugged cpu. This is
fair, since it is assumed that the pstate does not matter to a cpu in a deep idle
state, which is the expected state of a hotplugged core on powerpc. However on powerpc,
the pstate at a socket level is held at the maximum of the pstates of each core. Even
if the pstates of the active cores on that socket is low, the socket pstate is held
high due to the pstate of the hotplugged core in the above mentioned scenario. This
can cost significant amount of power loss for no good.

Besides, since it is a non active core, nothing can be done from the kernel's end
to set the frequency of the core right. Hence make use of the stop_cpu callback
to explicitly set the pstate of the core to a minimum when the last cpu of the
core gets hotplugged out.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Commit 367dc4aa ("cpufreq: Add stop CPU callback to
cpufreq_driver interface") introduced the stop CPU callback for
intel_pstate drivers. During the CPU_DOWN_PREPARE stage, this
callback is invoked so that drivers can take some action on the
pstate of the cpu before it is taken offline. This callback was
assumed to be useful only for those drivers which have implemented
the set_policy CPU callback because they have no other way to take
action about the cpufreq of a CPU which is being hotplugged out
except in the exit callback which is called very late in the offline
process.

The drivers which implement the target/target_index callbacks were
expected to take care of requirements like the ones that commit
367dc4aa addresses in the GOV_STOP notification event. But there
are disadvantages to restricting the usage of stop CPU callback
to cpufreq drivers that implement the set_policy callbacks and who
want to take explicit action on the setting the cpufreq during a
hotplug operation.

1.GOV_STOP gets called for every CPU offline and drivers would usually
want to take action when the last cpu in the policy->cpus mask
is taken offline. As long as there is more than one cpu in the
policy->cpus mask, cpufreq core itself makes sure that the freq
for the other cpus in this mask is set according to the maximum load.
This is sensible and drivers which implement the target_index callback
would mostly not want to modify that. However the cpufreq core leaves a
loose end when the cpu in the policy->cpus mask is the last one to go offline;
it does nothing explicit to the frequency of the core. Drivers may need
a way to take some action here and stop CPU callback mechanism is the
best way to do it today.

2. We cannot implement driver specific actions in the GOV_STOP mechanism.
So we will need another driver callback which is invoked from here which is
unnecessary.

Therefore this patch extends the usage of stop CPU callback to be used
by all cpufreq drivers as long as they have this callback implemented
and irrespective of whether they are set_policy/target_index drivers.
The assumption is if the drivers find the GOV_STOP path to be a suitable
way of implementing what they want to do with the freq of the cpu
going offine,they will not implement the stop CPU callback at all.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently allocate_resources() supports only CPU0 and it would need to allocate
resources for any CPU going forward.

Add another argument to it, i.e. cpu, and update code accordingly.
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently, we expect regulator name to be "cpu0", but as we are going to support
multiple cpu-blocks (all CPUs in a block share clock/voltage) later, we need to
pass some generic string instead of that.

For backwards compatibility try for "cpu0" first and if it fails, then try for
"cpu".
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently this driver only support platforms on which all CPUs share clock &
voltage lines and there is requirement to support platforms which have separate
clock & voltage lines for CPUs, like Qualcomm's Krait and ARM's big LITTLE.

Each group of CPUs sharing clock/voltage lines are represented by 'struct
cpufreq_policy' in cpufreq framework. And core calls ->init() once for each
policy.

Currently we do all initialization/allocation from probe() which wouldn't work
for above scenario. To make it work for these platforms, the first step is to
move all initialization/allocation to ->init() and add ->exit() to do the
reverse of it.

Also, remove all global variables and allocate space for them at runtime.

This patch creates 'struct private_data' for keeping all such information and
a pointer to that would be stored in policy->driver_data.

The changed probe() routine now tries to see if regulator/clocks are available
or we need to defer probe. In case they are available, it registers cpufreq
driver. Otherwise, returns with -EPROBE_DEFER.

We still *don't* support platforms with separate clock/voltage lines for CPUs.
This would be done in a separate patch later.
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

We already have cpu_dev and is used at multiple places for printing errors using
dev_*(). But some prints are still using pr_*(). Lets make it consistent and
replace those pr_*() macros with dev_*() macros.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently, we defer probe if regulator_get() returned -EPROBE_DEFER, i.e.
regulator isn't registered yet. We do a dev_err() in this case. Sending a
message to the log on probe defer just duplicates what the driver core is
already doing. Convert it to dev_dbg() instead.

We should defer in case of clk_get() as well.

Current code already does it, but it wasn't intentional probably. Its just that
we are returning the right error with wrong print message.

Fix print message to convey right error.
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

CPU clk is not optional for this driver and probe would fail if it couldn't find
a suitable clock.

And so, while calling clk_put() we don't need to validate clocks.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Two people are maintaining it now, Viresh and Shawn. Add Viresh's details in
MODULE_AUTHOR() and copyright section.
Suggested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Drivers supporting multiple clusters or multiple 'struct cpufreq_policy'
instances may need to keep per-policy data. If the core doesn't provide support
for that, they might do it in the most unoptimized way: 'per-cpu' data.

This patch adds another field in struct cpufreq_policy: 'driver_data'. It isn't
accessed by core and is for driver's internal use only.
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

These changes fix the argument to the kcalloc
        @n: number of elements.
        @size: element size.
        @flags: the type of memory to allocate (see kmalloc).

        void *kcalloc(size_t n, size_t size, gfp_t flags)

Fixes: 3c5445ce (cpufreq: OPP: Avoid sleeping while atomic)
Signed-off-by: Anand Moon <moon.linux@yahoo.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

It should have been removed with commit d1b68485
("cpufreq / intel_pstate: Optimize intel_pstate_set_policy")
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull Xtensa updates from Chris Zankel:
 "Xtensa improvements for 3.17:
   - support highmem on cores with aliasing data cache.  Enable highmem
     on kc705 by default
   - simplify addition of new core variants (no need to modify Kconfig /
     Makefiles)
   - improve robustness of unaligned access handler and its interaction
     with window overflow/underflow exception handlers
   - deprecate atomic and spill registers syscalls
   - clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
     statements
   - wire up renameat2 syscall.

  Various fixes:
   - fix address checks in dma_{alloc,free}_coherent (runtime BUG)
   - fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
   - fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
     (runtime unrecoverable exception)
   - fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
     register clobbering)
   - fix kernel/user jump out of fast_unaligned (potential runtime
     unrecoverabl exception)
   - replace termios IOCTL code definitions with constants (userspace
     build breakage)"

* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
  xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
  xtensa: don't allow overflow/underflow on unaligned stack
  xtensa: fix a6 and a7 handling in fast_syscall_xtensa
  xtensa: allow single-stepping through unaligned load/store
  xtensa: move invalid unaligned instruction handler closer to its users
  xtensa: make fast_unaligned store restartable
  xtensa: add double exception fixup handler for fast_unaligned
  xtensa: fix kernel/user jump out of fast_unaligned
  xtensa: configure kc705 for highmem
  xtensa: support highmem in aliasing cache flushing code
  xtensa: support aliasing cache in kmap
  xtensa: support aliasing cache in k[un]map_atomic
  xtensa: implement clear_user_highpage and copy_user_highpage
  xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
  xtensa: allow fixmap and kmap span more than one page table
  xtensa: make fixmap region addressing grow with index
  xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
  xtensa: add renameat2 syscall
  xtensa: fix address checks in dma_{alloc,free}_coherent
  xtensa: replace IOCTL code definitions with constants
  ...

unicore32 builds fail with

  arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
  arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
  arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
  arch/unicore32/kernel/signal.c: In function ‘do_signal’:
  arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
  make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
  make: *** [arch/unicore32/kernel/signal.o] Error 2

Bisect points to commit 649671c9 ("unicore32: Use get_signal()
signal_setup_done()").

This code never even compiled.  Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up.  Compile
tested only.

Fixes: 649671c9 ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM fixes from Russell King:
 "Various assorted fixes:

   - a couple of patches from Mark Rutland to resolve an errata with
     Cortex-A15 CPUs.
   - fix cpuidle for the CPU part ID changes in the last merge window
   - add support for a relocation which ARM binutils is generating in
     some circumstances"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
  ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
  ARM: 8128/1: abort: don't clear the exclusive monitors
  ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations

Pull ARM SoC fixes from Olof Johansson:
 "Here's the weekly batch of fixes from arm-soc.

  The delta is a largeish negative delta, due to revert of SMP support
  for Broadcom's STB SoC -- it was accidentally merged before some
  issues had been addressed, so they will make a new attempt for 3.18.
  I didn't see a need for a full revert of the whole platform due to
  this, we're keeping the rest enabled.

  The rest is mostly:

   - a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
   - some MTD/NAND fixes for OMAP
   - minor DT fixes for shmobile
   - warning fix for UP builds on vexpress/spc

  There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
  so it can boot.  Drivers and the rest had landed for 3.17, and it's
  small and isolated so it made sense to pick up now even if it's not a
  bugfix"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  vexpress/spc: fix a build warning on array bounds
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
  MAINTAINERS: catch special Rockchip code locations
  ARM: dts: microsom-ar8035: MDIO pad must be set open drain
  ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
  ARM: brcmstb: revert SMP support
  ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
  ARM: dts: Enable UART wake-up events for beagleboard
  ARM: dts: Remove twl6030 clk32g "regulator"
  ARM: OMAP2+: omap_device: remove warning that clk alias already exists
  ARM: OMAP: fix %d confusingly prefixed with 0x in format string
  ARM: dts: DRA7: fix interrupt-cells for GPIO
  mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
  ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
  ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
  mtd: nand: omap: Revert to using software ECC by default
  ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
  ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
  ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
  ...

With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:

arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
  struct ve_spc_opp *opps = info->opps[cluster];
                                      ^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:

Add basic subarchitecture support for the DRA72x and DRA74x.  These
are OMAP2+ derivative SoCs.  This should be low-risk to existing OMAP
platforms.

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/

* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull spi bugfixes from Mark Brown:
 "A smattering of bug fixes for the SPI subsystem, all in driver code
  which has seen active work recently and none of them with any great
  global impact.

  There's also a new ACPI ID for the pxa2xx driver which required no
  code changes and the addition of kerneldoc for some structure fields
  that were missing it and generating warnings during documentation
  builds as a result"

* tag 'spi-v3.17-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: sh-msiof: Fix transmit-only DMA transfers
  spi/rockchip: Avoid accidentally turning off the clock
  spi: dw: fix kernel crash due to NULL pointer dereference
  spi: dw-pci: fix bug when regs left uninitialized
  spi: davinci: fix SPI_NO_CS functionality
  spi/rockchip: fixup incorrect dma direction setting
  spi/pxa2xx: Add ACPI ID for Intel Braswell
  spi: spi-au1550: fix build failure
  spi: rspi: Fix leaking of unused DMA descriptors
  spi: sh-msiof: Fix leaking of unused DMA descriptors
  spi: Add missing kerneldoc bits
  spi/omap-mcspi: Fix the spi task hangs waiting dma_rx

spi: Bug fixes for v3.17

A smattering of bug fixes for the SPI subsystem, all in driver code
which has seen active work recently and none of them with any great
global impact.

There's also a new ACPI ID for the pxa2xx driver which required no code
changes and the addition of kerneldoc for some structure fields that
were missing it and generating warnings during documentation builds as a
result.

# gpg: Signature made Sun 31 Aug 2014 13:19:12 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg:                 aka "Mark Brown <broonie@debian.org>"
# gpg:                 aka "Mark Brown <broonie@kernel.org>"
# gpg:                 aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg:                 aka "Mark Brown <broonie@linaro.org>"
# gpg:                 aka "Mark Brown <Mark.Brown@linaro.org>"

Fix tx/rx mixup, which broke transmit-only transfers.

Introduced by commit 4240305f7cbdc7782aa8bc40cc702775d9ac0839
("spi: sh-msiof: Fix leaking of unused DMA descriptors").
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Pull file locking bugfx from Jeff Layton:
 "Just a bugfix for a bug that crept in to v3.15.  It's in a rather rare
  error path, and I'm not aware of anyone having hit it, but it's worth
  fixing for v3.17"

* tag 'locks-v3.17-3' of git://git.samba.org/jlayton/linux:
  locks: pass correct "before" pointer to locks_unlink_lock in generic_add_lease

Merge remote-tracking branches 'spi/fix/au1550', 'spi/fix/davinci', 'spi/fix/doc', 'spi/fix/dw', 'spi/fix/omap-mcspi', 'spi/fix/pxa2xx', 'spi/fix/rockchip' and 'spi/fix/rspi' into spi-linus

Pull x86 fixes from Peter Anvin:
 "One patch to avoid assigning interrupts we don't actually have on
  non-PC platforms, and two patches that addresses bugs in the new
  IOAPIC assignment code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, irq, PCI: Keep IRQ assignment for runtime power management
  x86: irq: Fix bug in setting IOAPIC pin attributes
  x86: Fix non-PC platform kernel crash on boot due to NULL dereference

Pull ACPI and power management fixes from Rafael Wysocki:

 - Fix for an ACPI regression related to the handling of fixed events
   that caused netlink routines to be (incorrectly) run in interrupt
   context from Lan Tianyu

 - Fix for an ACPI EC driver regression on Acer Aspire V5-573G that
   caused AC/battery plug/unplug and video brightness change
   notifications to be delayed on that machine from Lv Zheng

 - Fix for an ACPI device enumeration regression that caused ACPI driver
   probe to fail for some devices where it succeeded before (Rafael J
   Wysocki)

 - intel_pstate driver fix to prevent it from printing an information
   message for every CPU in the system on every boot from Andi Kleen

 - s5pv210 cpufreq driver fix to remove an __init annotation from a
   routine that in fact can be called at any time after init too from
   Mark Brown

 - New Intel Braswell device ID for the ACPI LPSS (Low-Power Subsystem)
   driver from Alan Cox

 - New Intel Braswell CPU ID for intel_pstate from Mika Westerberg

* tag 'pm+acpi-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: s5pv210: Remove spurious __init annotation
  cpufreq: intel_pstate: Add CPU ID for Braswell processor
  intel_pstate: Turn per cpu printk into pr_debug
  ACPI / LPSS: Add ACPI IDs for Intel Braswell
  ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC
  ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
  ACPI: Run fixed event device notifications in process context
  ACPI / scan: Allow ACPI drivers to bind to PNP device objects

Merge patches from Andrew Morton:
 "22 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
  kexec: purgatory: add clean-up for purgatory directory
  Documentation/kdump/kdump.txt: add ARM description
  flush_icache_range: export symbol to fix build errors
  tools: selftests: fix build issue with make kselftests target
  ocfs2: quorum: add a log for node not fenced
  ocfs2: o2net: set tcp user timeout to max value
  ocfs2: o2net: don't shutdown connection when idle timeout
  ocfs2: do not write error flag to user structure we cannot copy from/to
  x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
  drivers/rtc/rtc-s5m.c: re-add support for devices without irq specified
  xattr: fix check for simultaneous glibc header inclusion
  kexec: remove CONFIG_KEXEC dependency on crypto
  kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
  x86,mm: fix pte_special versus pte_numa
  hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
  mm/zpool: use prefixed module loading
  zram: fix incorrect stat with failed_reads
  lib: turn CONFIG_STACKTRACE into an actual option.
  mm: actually clear pmd_numa before invalidating
  memblock, memhotplug: fix wrong type in memblock_find_in_range_node().
  ...

Without this patch the kexec-purgatory.c and purgatory.ro files are not
removed after make mrproper.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add arm specific parts to kdump kernel documentation.
Signed-off-by: Hu Keping <hukeping@huawei.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix building errors occuring due to a missing export of
flush_icache_range() in

kisskb.ellerman.id.au/kisskb/buildresult/11677809/

ERROR: "flush_icache_range" [drivers/misc/lkdtm.ko] undefined!
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>	[arc]
Acked-by: Richard Kuo <rkuo@codeaurora.org>	[hexagon]
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>	[xtensa]
Cc: Noam Camus <noamc@ezchip.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Zhigang Lu <zlu@tilera.com>		[tile]
Cc: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the typo of ARCH when running 'make kselftests'.  Change the 'X86'
to 'x86'.  Test by compilation.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Shuah Khan <shuah.kh@samsung.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For debug use, we can see from the log whether the fence decision is
made and why it is not fenced.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When tcp retransmit timeout(15mins), the connection will be closed.
Pending messages may be lost during this time.  So we set tcp user
timeout to override the retransmit timeout to the max value.  This is OK
for ocfs2 since we have disk heartbeat, if peer crash, the disk
heartbeat will timeout and it will be evicted, if disk heartbeat not
timeout and connection idle for a long time, then this means the cluster
enters split-brain state, since fence can't happen, we'd better keep the
connection and wait network recover.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch series is to fix a possible message lost bug in ocfs2 when
network go bad.  This bug will cause ocfs2 hung forever even network
become good again.

The messages may lost in this case.  After the tcp connection is
established between two nodes, an idle timer will be set to check its
state periodically, if no messages are received during this time, idle
timer will timeout, it will shutdown the connection and try to
reconnect, so pending messages in tcp queues will be lost.  This
messages may be from dlm.  Dlm may get hung in this case.  This may
cause the whole ocfs2 cluster hung.

This is very possible to happen when network state goes bad.  Do the
reconnect is useless, it will fail if network state is still bad.  Just
waiting there for network recovering may be a good idea, it will not
lost messages and some node will be fenced until cluster goes into
split-brain state, for this case, Tcp user timeout is used to override
the tcp retransmit timeout.  It will timeout after 25 days, user should
have notice this through the provided log and fix the network, if they
don't, ocfs2 will fall back to original reconnect way.

This patch (of 3):

Some messages in the tcp queue maybe lost if we shutdown the connection
and reconnect when idle timeout.  If packets lost and reconnect success,
then the ocfs2 cluster maybe hung.

To fix this, we can leave the connection there and do the fence decision
when idle timeout, if network recover before fence dicision is made, the
connection survive without lost any messages.

This bug can be saw when network state go bad.  It may cause ocfs2 hung
forever if some packets lost.  With this fix, ocfs2 will recover from
hung if network becomes good again.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If we failed to copy from the structure, writing back the flags leaks 31
bits of kernel memory (the rest of the ir_flags field).

In any case, if we cannot copy from/to the structure, why should we
expect putting just the flags to work?

Also make sure ocfs2_info_handle_freeinode() returns the right error
code if the copy_to_user() fails.

Fixes: ddee5cdb ('Ocfs2: Add new OCFS2_IOC_INFO ioctl for ocfs2 v8.')
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>